For more information, visit www.fmiproducts.com
INSTALLATION INSTRUCTIONS FOR
BI-FOLD AND CABINET GLASS DOORS
If any of these parts are missing or damaged, call FMI
PRODUCTS, LLC at 1-866-328-4537.
BI-FOLD GLASS DOORS
USE GLASS DOORS CERTIFIED FOR USE WITH YOUR
APPLIANCE OR FIREPLACE ONLY
Door Installation
Pivot and spring clips have been installed and pretested at
the factory, but some readjustments may be needed due to
movement during shipping or handling.
Install doors using the following steps. If you nd the doors
do not close properly or do not appear level or straight,
proceed with section on door adjustment.
1. With bi-fold door completely folded, insert bottom pivot
pin into pivot plate or pivot hole located near bottom
corner of front face. Open and swing door to vertical
position making sure top pins slide into door track.
Door is installed when top door pin snaps into spring
clip (see Figure 1).
2. Repeat step 1 for remaining door.
Spring Clip
Fold Door and
Slide Top Pins
into Track
Insert Pin into
Spring Clip
Pivot Plate or
Pivot Hole
Insert Bottom
Pivot Pin into
Pivot Plate or
Pivot Hole and
Swing Door
to the Vertical
Position
Care and Operating Guidelines
• Glass doors should be operated in the fully open or
fully closed positions only (see Figure 3).
• When operating doors, do not slam shut or abuse
them.
• Always keep area below bottom edge of doors clear
from obstacles or debris.
• Do not operate this appliance if glass doors are broken
or damaged.
• Do not use abrasive liquids or cleaners for cleaning
of glass and door trims. Any household glass cleaner
should sufce. Do not clean doors when hot, allow ap
Figure 3 - Bi-Fold Doors Fully Open
Figure 2 - Door Adjustment
Figure 1 - Bi-Fold Door Installation
Spring
Clip
Side Front
Face
Partially
Opened
Door
FULLY OPEN
Door Adjustment
Remove doors and slightly loosen lower pivot plate (if
equipped) and upper spring clips. Replace doors and fully
close them. Use 1/8'' shims (any material) to level doors.
Once the proper setting is achieved, carefully open doors
enough so that you can access pivot and spring clips with a
Phillips screwdriver. Tighten screws (see Figure 2).
Please read Care and Operating Guidelines, column 2,
before operating your appliance or replace.
www.fmiproducts.com
107540-01F
2
2. With cabinet door open, insert bottom pivot pin into
pivot plate located near bottom corner of front face
opening. Swing door to the vertical position, making
sure top pin slides into door track. Door is installed
when top door pin snaps into spring clip (see gur 5).
Please read Care and Operating Guidelines on page 1
before operating your appliance or replace.
Figure 4 - Replacing Door Stops on Various Models
CABINET GLASS DOORS
Door Installation
Cabinet type doors require a different type of door stop
than the standard factory-installed door stop basically de-
signed for bi-fold doors.
1. Remove old door stop by removing screws. Some
models may have old door stops fastened with rivets.
In this case, drilling will be required. Using new door
stop bracket as a template, measure and align to the
center of bottom front face and proceed to drill a 0.42''
diameter hole (see Figure 4). Install bracket with pro-
vided screws.
Figure 5 - Installing Glass Door
FULLY OPEN
CABINET TYPE DOORS
Figure 6 - Cabinet Doors Fully Opened
Use Door Stop
Bracket as
Template to Drill
Two 0.42'' dia.
Holes for Bullet
Retainers and
Two 0.124'' dia.
Pilot Holes for
Screws
Door Stop
Bracket
Bullet
Retainer
May Be
Adjusted
Bullet
Retainer
May Be
Adjusted
Use Door Stop
Bracket as
Template to Drill
Two 0.42'' dia.
Holes for Bullet
Retainers and
Two 0.124'' dia.
Pilot Holes for
Screws
Door Stop
Bracket
Pivot Plate
Spring Clip
Insert Pin into
Spring Clip
Insert Bottom
Pivot Pin into
Pivot Plate and
Swing Door
to the Vertical
Position
Side Top
Pin into
Door
Track
www.fmiproducts.com
107540-01F
3
CABINET GLASS DOORS AND SIDE PANEL
DBPPN36, DC36PN AND DG36PN MODELS
ONLY.
Installation
1. Identify the left and right doors and side panel (see
Figure 7)
2. To install the glass panel, insert the two pins, located
on the top of the glass panel frame, into the top corner
holes (see gure 8).
3. Push the glass panel as far up as possible so that the
two pins located on the bottom of the glass panel will t
into the two holes located on the bottom corners of the
replace opening. Adjust the glass panel until it is fully
seated. Refer to Figures 8.
4. Install the left and right doors. Be sure top spring clip
hole is aligned with hole in replace frame (see Figure
9). Fit glass door top pin into aligned holes.
5. Swing inner end of bottom clip out away from replace
frame. Fit door bottom pin into clip. Push clip into frame
until bottom door pin slips into hole in frame.
6. Check door alignment. If doors do not align with each
other, use top spring clip to align.
7. Use Phillips screwdriver to loosen screw that holds top
spring clip in place.
8. Push spring clip left or right in its alignment slot until
door is at proper angle (aligned with opposing door).
Moving spring clip to the LEFT (your left as you face
the replace) moves glass door’s top, inner corner UP;
moving spring clip to the RIGHT moves glass door’s top,
inner corner DOWN.
9. When door alignment is satisfactory, use Phillips screw-
driver to retighten spring clip screw.
Note: When glass doors are aligned properly, the bot-
tom hole of the aluminum trim, snaps into the bullet
catch.
WARNING: When replace is in operation, both sets
of cabinet doors on each side of the replace must be
either FULLY OPEN or FULLY CLOSED. If not, a re haz-
ard may be created.
Figure 8 - Mounting Hole Locations for Side Panel
Figure 7 - Identifying Cabinet Doors
Figure 9 - Installing Glass Doors
Adjustment
Clip
Adjustment
Screw
Top Slot
Under Frame
Long
Pivot Pin
Bottom Pin
Bottom Slot
Adjustment Clip
Left Cabinet Door
Right Cabinet Door
Side Panel
Holes for the
Left Cabinet
Door
Holes for
the Glass
Panel
Figure 10 - Cabinet Glass Doors Shown Fully Open
Glass Doors Must be Fully Open (as Shown) or Fully Closed when
Appliance is in Operation
107540-01
Rev. F
09/13
2701 S. Harbor Blvd.
Santa Ana, CA 92704
1-866-328-4537
www.fmiproducts.com
-
1
-
2
-
3
-
4
