Troy-Bilt 21A-644H063 Owner's manual

Brand: Troy-Bilt

Model: 21A-644H063

Category: Mini tillers

Type: Owner's manual

This manual is also suitable for

0 TRtlI BILT°

Operator's Manual

Rear-tine Tiller Models

644H--Bronco TM

645A--Bronco TM

Model 644H Shown (bumper syles vary)

IMPORTANT:READ SAFETY RULES AND INSTRUCTIONS CAREFULLY

Warning: This unit is equipped with an internal combustion engine and should not be used on or near any unimproved forest-covered, brush-

covered or grass-covered land unless the engine's exhaust system is equipped with a spark arrester meeting applicable local or state laws (if any).

If a spark arrester is used, it should be maintained in effective working order by the operator. In the State of California the above is required by law

(Section 4442 of the California Public Resources Code). Other states may have similar laws. Federal laws apply on federal lands. A spark arrester

for the muffler is available by contacting the service department at Troy-Bilt LLC, P.O. Box 361131 Cleveland, Ohio 44136-0019.

TROY-BILT LLC, P.O. BOX 361131, CLEVELAND, OH 44136-0019

PRINTED IN USA FROM NO. 769-00585A

(01/2003)

TABLE OF CONTENTS

Content Page

Calling Customer Support .................................................... 2

Safety ................................................................... 3

Assembly................................................................. 6

Features and Controls ....................................................... 10

Operation ................................................................ 13

Maintenance .............................................................. 19

Off-Season Storage ........................................................ 24

Troubleshooting ........................................................... 25

Parts List................................................................. 26

Warrany Information ........................................................ Back Cover

FINDINGMODELNUMBER

This Operator's Manual is an important part of your new Rear-tineTiller. It wilt help you assemble, prepare and

maintain the unit for best performance. Please read and understand what itsays.

Before you start assembling your new equipment, please locate the model plate on the equipment and copy the infor-

mation from it in the space provided below. This information is very important if you need help from our Customer

Support Department or an authorized dealer.

You can locate the model number by looking at the rear surface of the tine shield. A sample model plate is

explained below. For future reference, please copy the model number and the serial number of the equipment

in the space below

OTRII BILT" TROY-BILT LLC

P. O. BOX 361131

www.troybilt.com CLEVELAND,OH44136

330-558-7220

• 866-840-6483j

Copy Model Number Here

Copy Serial Number Here

ENGINEINFORMATION

The engine manufacturer is responsible for all engine-related issues with regards to performance, power-rating, speci-

fications, warranty and service. Please refer to the engine manufacturer's Owner's/Operator's Manual packed sepa-

rately with your unit for more information.

CALLING CUSTOMER SUPPORT

If you have difficulty assembling this product or have any questions regarding the controls, operation or maintenance

of this unit, please call the Customer Support Department.

Call 1- (330) 558-7220 or 1- (866) 840-6483 to reach a Customer Support representative. Please have

your unit's model number and serial number ready when you call. See previous section to locate this

information. You will be asked to enter the serial number in order to process your call ..

Safety

SPARKARRESTERWARNINGTORESIDENTSOFCALIFORNIAANDSEVERALOTHERSTATES

UnderCalifornia law,and under the laws of severalother states,you are not permitted to operatean

internalcombustion engineusing hydrocarbon fuels on anyforest, brush, hay, grain, orgrass

covered land;or land covered byany flammableagricultural crop without an engine spark arrester in

continuous effectiveworking order.

Theengineon theunit is an internal combustion engine whichburns gasoline,a hydrocarbon fuel, and must be equippedwith a

spark arrester muffler in continuous effectiveworking order. Thespark arrester must be attachedto the engine exhaustsystem in

such a manner that flames or heatfrom the systemwill not ignite flammablematerial. Failureof the owner/operator of the unit to

comply with this regulation is a misdemeanorunder California law (and other states) and may also bea violation of other state

and/or federalregulations, laws, ordinancesor codes, Contactyour localfire marshal or forest servicefor specific information

aboutwhich regulations applyin your area,

Training

1. Carefully readthis

Owner's Manual,the

separateEngineOwner's

Manual, andany other literature you may

receive,Bethoroughly familiar with the

controls and the proper useof the tiller

and its engine. Know howto stop theunit

and disengagethe controls quickly.

2. Neverallow children to operatethe

tiller,Neverallow adults to operatethe

tiller without proper instruction,

3, Keepthe area of operationclear of all

persons, particularlychildren and pets.

4. Keepin mindthat theoperator or user

is responsible for accidents or hazards

occurring to other people,their property,

and themselves.

Preparation

1. Thoroughly inspect theareawhere the

tilleris to be usedand remove all foreign

objects.

2. Besure all tiller controls are released

and both wheels arein the WheelDrive

position beforestarting theengine,

3. Do not operatethetiller without

wearingadequateouter garments. Avoid

loosegarments orjewelry that could get

caught in moving parts.

4. Do not operatethetillerwhen barefoot

or wearing sandals,sneakers,or light

footwear. Wearprotective footwearthat

will improve footing on slippery surfaces,

5. Donot till near underground electric

cables,telephonelines, pipesor hoses. If

in doubt, contact your telephoneor utility

company,

6. Warning: Handlefuel with care; it is

highly flammableand its vaporsare

explosive. Besureto take thefollowing

precautions:

a, Storefuel in containers specifically

designedfor this purpose.

b, Thegascap shall neverbe removed

or fuel addedwhile the engine is

running, Allow theengine to cool

for several minutes beforeadding

fuel.

Keepmatches,cigarettes, cigars,

pipes, open flames,and sparks

away from the fuel tank and fuel

container.

d, Fillfueltank outdoors with extreme

care. Neverfill fuel tank indoors,

Usea funnel or spout to prevent

spillage.

e, Replaceall fuel tank and container

caps securely,

f. If fuel is spilled, do not attempt to

start the engine, but move the

machineaway from the areaof

spillage and avoidcreating any

source of ignition until fuel vapors

havedissipated,

7. Never makeadjustments whenengine

is running (unless recommendedby

manufacturer).

Operation

1. Do not put hands or feet nearor under

rotating parts. Thetines begin to rotate

oncethe engine starts and the Forward

Clutch Bail (or ReverseClutchControl) is

engaged.

2. Exerciseextremecaution whenon or

crossing gravel drives,walks, or roads,

Stay alert for hidden hazardsor traffic. Do

not carry passengers,

3. After striking a foreign object, stop the

engine,remove thewire from the spark

plug and preventit from touchingthe

spark plug, thoroughly inspectthe

machine for any damage,and repair the

damagebeforerestarting and operating

the machine.

4. Exercisecaution to avoid slipping or

falling.

5. If the unit should start to vibrate abnor-

mally, stop theengine, disconnect the

spark plug wire and prevent it from

touching the spark plug, and check

immediately for thecause.Vibration is

generallya warning of trouble.

6. Stop theengine, disconnect the spark

plug wire and preventit from touching

the spark plug wheneveryou leavethe

operating position, beforeunclogging the

tines, or when making anyrepairs,adJust-

ments or inspections,

Section1: Safety

7. Takeall possible precautionswhen

leavingthe machineunattended,Stop the

engine. Disconnectspark plug wire and

move it away from the spark plug. Be

sure both wheels are in the WheelDrive

position,

8. Beforecleaning, repairing, or inspect-

ing,stop the engineand makecertain all

moving parts havestopped, Disconnect

the spark plug wire and prevent it from

touching the spark plug to prevent acci-

dentalstarting.

9. Theflap on the tine hood must be

down whenoperating thetiller.

10. Neverusethe tiller unless proper

guards, plates,or other safety protective

devicesare in place.

11. Do not run enginein an enclosed

area,Engineexhaustcontains carbon

monoxide gas,a deadlypoisonthat is

odorless, colorless, and tasteless,

12. Keepchildren andpetsaway.

13. Never operatethetiller under

enginepowerifthewheels are in the

Freewheelposition.In the Freewheel

position,thewheels will not holdthe

tiller backandthe revolvingtines could

propelthetiller rapidly, possibly

causinglossofcontrol.Alwaysengage

thewheelswith thewheel drive pinsin

theWheelDrive positionbefore starting

theengineor engaging thetines/wheels

with theForward Clutch Bailor the

ReverseClutchControl.

14. Beawarethat the tiller may unexpect-

edly bounceupward orjump backward

and be propelled toward you if the tines

should strike extremely hard packedsoil,

frozen ground, or buried obstacles like

largestones, roots, or stumps, If in doubt

about thetilling conditions, alwaysuse

the following operating precautions to

assist you in maintaining control of the

tiller:

a. Walk behindand toone sideofthe

tiller, usingone handon thehan-

dlebars. Relaxyourarm, butusea

securehandgrip.

b. Usea deepdepthregulator

setting.

c. Useslowerengine speeds.

d. Clearthetilling area ofall large

stones,rootsandotherdebris.

e. Avoidusingdownwardpressure

on handlebars.If needbe, use

slightupwardpressuretokeepthe

tinesfrom diggingtoodeeply.

f. Beforecontactinghardpackedsoil

at the endofa row, reduceengine

speedand lift handlebarstoraise

tinesout ofthesoil.

In anemergency,stoptinesand

wheelsbyreleasingwhichever

clutchcontrolisengaged. Donot

attemptto restrainthetiller.

15. Do not overloadthetiller's capacity

by attempting to till too deeplyat too fast

a rate.

16. Neveroperatethe tiller at high

transport speedson slippery surfaces,

Look behind and usegreat carewhen

backing up,

17. Do not operatethe tiller on a slope

that istoo steep for safety,When on

slopes, slow down and makesureyou

havegood footing, Never permit the tiller

to freewheeldown slopes,

18. Neverallow bystanders nearthe unit,

19. Onlyuseattachments and acces-

sories that areapproved bythe manufac-

turer of the tiller,

20. Usetiller attachments and acces-

sories when recommended.

21. Neveroperatethe tiller withoutgood

visibility or light.

22. Neveroperatethe tiller ifyouare

tired, or under the influenceof alcohol,

drugs or medication.

23. Operatorsshall not tamper with the

engine-governorsettings on the machine;

the governor controls the maximum safe

operating speedto protect the engineand

all moving parts from damagecausedby

overspeed, Authorized serviceshall be

sought if a problem exists.

24. Do nottouch engine partswhichmay

be hot from operation. Let parts cool

down sufficiently.

25. Pleaseremember:Youcan always

stop the tines and wheels by releasingthe

ForwardClutchcontrol or the Reverse

Clutchcontrol (whichevercontrol you

haveengaged),or by moving the throttle

control lever on the engineto "OFF"or

"STOP".

26. To load or unload the tiller, seethe

instructions in Section4 of this Manual.

27. Useextremecaution whenreversing

or pulling the machinetowards you.

28. Start theengine carefullyaccordingto

instructions and with feet well awayfrom

thetines.

29. Neverpick up or carry a machine

while theengine is running.

MaintenanceandStorage

1. Keepthe tiller, attachments and acces-

sories in safeworking condition.

2. Checkall nuts, bolts, and screws at

frequent intervalsfor proper tightness to

besure the equipment is in safeworking

condition.

3. Neverstore the tiller with fuel in the

fueltank insidea building whereignition

sourcesare present such as hot water

andspace heaters,furnaces,clothes

dryers, stoves,electric motors, etc.).

Allow engineto cool beforestoring in any

enclosure.

4. To reducethechancesof a fire hazard,

keepthe engine freeof grass,leaves,or

excessivegrease.

5. Storegasolinein a cool, well-ventilated

area,safelyaway from any spark- or

flame-producing equipment, Store

gasolinein anapproved container,safely

awayfrom the reachof children.

6. Referto the Maintenancesections of

this Manualand theseparateEngine

Owner'sManual for instructions if the

tiller isto be stored for an extended

period.

7. Neverperform maintenancewhile the

engineis running or the spark plug wire

is connected,exceptwhen specifically

instructed to do so.

8. If the fuel tank hasto be drained,do

this outdoors,

Section1: Safety

Decals

Foryour safety andthe safety of others,

various safetyand operational decalsare

located on your unit (seeFigure1 below).

Keepthe decals cleanand legible atall

times, Contactyour localservice dealer

or the factory for replacementsif any

decalsare damagedor missing,

Referto the separateparts catalog for

decallocations, part numbers and

ordering instructions.

ForwardClutchControl

OperatingInstruction

ReverseClutchControl

_ OperaUngInstruction

StartingStabilization

Messageonengine

WarningMessages

ontinehood

HotSurfaces

Warningonbeltcover

Figure1:LocationofSafetyandOperatingDecals(Model 644Hshown).

OperatingSymbols

Various symbols (shown here, with word

descript'_ns)are used on the tiller and engine

(your unit may not haveallof thesymbols).

FAST SLOW STOP

H I÷1

CHOKE CHOKE

ON OFF

(--411

TILLERDIRECTION

REVERSE

ROTATING

TINES

(-- o--->

LEVERDIRECTION

BAIL

ENGAGED

BAIL

DISENGAGED

TO AVOID SERIOUS INJURY:

READTHE OWNER'SMANUAL.

KNOWLOCATIONSANDFUNCTIONSOFALLCONTROLS.

KEEPALLSAFETYDEVICESAND SHIELDSIN PLACEANDWORKING.

NEVERALLOWCHILDRENOR UNINSTRUCTEDADULTSTO OPERATETILLER.

SHUTOFFENGINEANDDISCONNECTSPARKPLUGWIRE BEFOREMANUALLYUNCLOG-

GINGTINESORMAKINGREPAIRS.

KEEPBYSTANDERSAWAYFROMMACHINE.

KEEPAWAYFROMROTATINGPARTS.

USEEXTREMECAUTIONWHENREVERSINGORPULLINGTHEMACHINETOWARDSYOU.

Assembly

WARNING

To prevent personal injury or

property damage, do not start

the engine until all assembly

steps are complete and you

have read and understand the

safety and operating instruc-

tions in this manual.

Introduction

Carefullyfollow theseassembly steps to

correctly prepareyour tiller for use, It is

recommendedthat you readthis Section

in its entirety before beginningassembly,

NOTE: Enginesylesvary by model, The

engineon your tiller may appeardiffer-

ently than those shown in illustrations

and Figuresthroughout this manual,

Inspect unit

Inspect the unit and carton for damage

immediately after delivery. Contactthe

carrier (trucking company) if you find or

suspect damage, Inform them of the

damageand request instructions for filing

aclaim. To protect your rights, put your

claim in writing and mail acopy to the

carrierwithin 15 daysafter theunit has

beendelivered,

STEP1: UnpackingInstructions

1. Removeanycardboard inserts and

packagingmaterial from the carton.

Removeany staplesfrom the bottom of

thecarton and then lift thecarton up and

off theunit.

2,Thetiller is heavyandyou should not

attempt to remove it from the shipping

platform until the handlebarsare

installed, Theprocedurefor removing the

tiller is explainedin Step3 of these

assemblysteps.

NOTE:Becareful not to severelybendany

of the control cables on the unit.

3. Removeall unassembledpartsand

the separatehardwarebag from the

carton, Checkthat you havethe items

listed below (contact your localdealer or

the factory if any items are missing or

damaged), NOTE: Usethe screw length

template (Fig, 2-1) to identify screws,

LoosePartsList

Qty. Description

1 HandlebarSupport (seeA, Fig, 2-2,

page7)

1 HandlebarAssembly

(seeK, Fig,2-2)

Thefollowing itemsare in the

hardwarebag:

1 Slotted hd. screw, #10-24 x 2"

1 Hexhd, screw, 1/4-20 x 1-1/4"

6 Curvedhd. screw, 5/16-18 x 1-1/2"

2 Hexhd, screw, 3/8-16 x 3/4"

2 Flatwasher,3/8"

6 Split Iockwasher,5/16"

1 HexIocknut, 1/4"-20

6 Hexnut, 5/16"-18

2 HexIocknut, 3/8"-16

1 Hexnut,#10-24

1 Spring, cable(seeW, Fig. 2-5,

page8)

1 Bracket,forward clutch cable (see

P,Fig, 2-5, page8)

1 Bracket,reverseclutch cable (see

BB,Fig, 2-8, page9).

IMPORTANT:Motoroil mustbeaddedto

the enginecrankcasebeforethe engine

isstarted. Followthe instructionsinthis

"Assembly"section.

NOTE:LEFTand RIGHTsides of the tiller

are asviewed from the operator's

position behindthe handlebars.

Tools]MaterialsNeededfor

Assembly

(1) 3/8" open-endwrench*

(2) 7/16" open-endwrench*

(1) l/2" open-endwrench*

(2) 9/16" open-endwrench*

(1) Large adjustablewrench

(1) Scissors (to trim plastic ties)

(1) Ruler (for belt tension check)

(1) Block of wood (to support tiller

whenremoving wheels)

(1) Automotive-type air pressure gauge

(1) Cleanoil funnel

(1) Clean,high-quality engine oil Refer

to the EngineOwnerManualfor

engineoil specifications andquantity

required, Do not overfill,

* Adjustablewrenches may be used.

Figure2-1: Toidentifylengthofscrew,

placescrewontemplateasshownand

measuredistancebetweenbottomofscrew

headandtipofscrew.

STEP2: Attach Handlebar

1. Attachthe two legs ofthe handlebar

support (A, Fig.2-2) loosely tothe inner

sides of the tiller frame using two 3/8"-16

x 3/4" hexhd. screws(B), 3/8" flat

washers(C) and 3/8"-16 hexIocknuts (D).

2. Using the middle holesin the handlebar

support brackets (Eand F,Fig. 2-2),

loosely attachthe support brackets to the

handlebarsupport (A) using two 5/16"-18

x 1-1/2" curvedhd. screws (G),5/16" split

Iockwashers (H)and 5/16"-18 hexnuts (I).

NOTE:If a support bracketwill not move,

loosenattaching screw (J) and nut.

3. Attach the handlebarassembly (K) to

thehandlebarsupport (A) using four

5/16"-18 x 1-1/2" curvedhd. screws (G),

5/16" split Iockwashers(H) and 5/16"-18

hexnuts (1).Tighten the four screws

securely.

4. Tighten all handlebarmounting

hardwaresecurely.

STEP3: MoveTiller OffShipping

Platform

Tomove the tiller withouttheengine

running, put the wheelsin their

FREEWHEELposition, asdescribed below.

1. Usea sturdy block to raiseonewheel

off theground.

2. Removethe hairpin cotter (L, Fig.2-3)

and wheeldrive pin (M). Slide the wheel

inward on the wheelshaft (N). Reinstall

thewheel drive pin and hairpin cotter

through the wheelshaft only (not through

thewheel hub). Repeatwith the other

wheel.

3. Using the handlebaras a lever,roll the

tiller to aflat area.

IMPORTANT:Beforestarting the engine,

thewheels must be placedin theirWHEEL

DRIVEposition (pins through wheel hubs

and wheelshaft). This procedureis

described in "Wheel DrivePins" in

Section 3.

Fig. 2-2: Attachhandlebar.

Fig. 2-3: Wheel in FREEWHEELING

position(wheel drivepin throughwheel

shaRonly).

Section2: Assembly

STEP4: Install ForwardClutch Cable

1. Placetheforward clutch cablebracket

(P,Fig. 2-4) on the handlebarsupport (A).

Attach thecable bracketusing a 1/4"-20 x

1-1/4" hexhd, screw (R,Fig. 2-4) and

1/4"-20 hexIocknut (S).Tighten securely.

2. Carefullyunwrap the forward clutch

cable (thecablewithout a knob attachedto

it) from its shipping position and slide the

thin cablewire (T, Fig. 2-4) into the slot in

thecablebracket. Pushthecableconnector

(U, Fig,2-4) up through the hole in the

bracket until the groove in the connector

snaps into placeon the bracket.

3. Insertthe #10-24 x 2"slotted hd. screw

(V,Fig. 2-5) down into the cablespring

(W). Thethreadedend of thescrew will

extend from the bottom of the spring.

4. Threadthe#10-24 hex nut (Z) on the

slottedheadscrew(V).Threadit halfwayup,

5. Threadscrew (V) intocableadjuster (X),

6. Hook cablespring (W, Fig. 2-6) into "V"-

shapedbend in theforward clutch bail (Y).

7. Lift and hold the ForwardClutch bail

against the handlebar.SeeFig, 2-7,

8. Measurethe length of the cablespring

betweenthe ends of the coils (Fig. 2-7).

Thelength should be approximately 1-7/8".

If the length is correct, turn the #10-24 hex

nut (Z) down tightly againstthe cable

adjuster (X) while holding theadjuster in

place. SeeFigure2-7, If the length is

incorrect, you must makean adjustmentto

the cabletension as described in

"Checking andAdjusting Forward Drive

Belt Tension"in Section 5. Whenthe

spring length is correct, tighten the hex nut

(Z)against the cableadjuster (X).

STEP5: Install ReverseClutch

Cable

1. Removethetwo pre-installedself-tapping

screws (AA,Fig, 2-8) from the handlebars.

2. Position the reversecablemounting

bracket (BB,Fig, 2-8) asshown and

reinstall thetwo self-tapping screws.

3. Unwrapthe reverseclutch cable (the

cablewith a knoband a large hex nut

attachedto it) from around its shipping

positionand routethe cable(CC,Fig.2-8

and Fig,2-9) up to thecable bracket(BB,

Fig, 2-8), Be surethat thecable goes

beneaththe ForwardClutch Bailas it is

routed up to the cablebracket.

Fig. 2-4: Installing forwardclutchcable bracketand cable.

W-- Fig.2-5:Assemble

springandadjuster.

V-- --Z

X--

Fig,2-6:Installforwardclutchcable,

Fig.2-7:Measurecablespring.

Section2: Assembly

4. Insertthe cableup through the slot in

the cablebracketand position the

threadedassembly asshown in Fig, 2-8,

Makesurethat the flat sideof the

threadedassembly is aligned with the fiat

side of the mounting hole, Slidethe large

hexnut (DD) up thecableand tighten it

securely,

5. Usea cabletie (EE,Fig,2-9) to fasten

the reverseclutch cableto the left side

handlebar,

6. Testthe function of the reverseclutch

cable by pulling the knob out and

releasingit. Theknob should return to its

neutralposition(resting against bracket)

when it is released. If it doesn't, contact

your localdealer or the factory for

technical assistance,

AA_

FlatSide

Fig.2-8:Installreversecablemounting

bracketandthereverseclutchcable.

STEP6: CheckLevelof

TransmissionGearOil

Thetransmission was filled with gear oil

at the factory. However,you should check

the gear oil levelto make certain it is

correct.

IMPORTANT:Donot operatethe tiller if

the gear oil levelis low. Doingso will

result in severedamageto the transmis-

sion components,

1. Putthe tiller on level ground. Pull the

DepthRegulator Lever (FF,Fig. 2-10)

back and then adjust it up or down to the

notch that makesthe tiller level.

2. Removethe oil fill plug (GG,Fig, 2-11)

from the transmission housing and look

into theoil fill hole. You will seethe main

drive shaft on one sideof the hole,

3. The gearoil level is correct if the gear

oil is approximately halfwayup the side of

the drive shaft,

4. Ifthe gear oil levelis low, add gear oil

by referring to "A. To Checkthe Transmis-

sion GearOil Level"in Section 5,

STEP7: Add Motor Oil to Engine

The tiller isshippedwithoutoil in the

engine.

IMPORTANT: Do not start the engine

without first adding motor oil.Severe

engine damagewill result if the engineis

run without oil,

1. Referto the EngineOwner's Manual

(suppliedwith tiller) for engine oilspecifi-

cations and capacities,

2. With the tiller on levelground, pullthe

DepthRegulator Lever (FF,Fig. 2-10)

back and then slide it up or downas

necessaryuntil theengine is level.

3. Add motor oil asdescribed in the

EngineOwner's Manual.

4. Movethe Depth RegulatorLeverall the

way down until the highest notch is

engaged, This placesthetines in the

"travel" position,

Fig, 2-10: AdjustDepthRegulator Lever.

Fig.2-11:Removegearoilfillplug.

STEP9: CheckAirPressurein

Tires)

Usea tire pressuregauge to checktheair

pressurein both tires, Deflateor inflate

both tires equallyto 15-to-20 PSI

(pounds per square inch), Be surethat

both tires are inflatedequallyor the unit

will pullto one side.

IMPORTANT: This completes the

assembly steps, Beforeoperating your

tiller, make sureyou readthe following

Sectionsin this Manual, aswell as the

separateEngineOwner's Manual:

• Section 1: "Safety"

• Section 3: "FeaturesandControls"

• Section 4: "Operation"

Fig. 2-9: Routereverseclutchcable(CC)as

shown. Attachtohandlebarwith cable tie

(EE).

STEP8: CheckHardwarefor

Tightness

Checkall nuts and screws for tightness,

FeaturesandControls

WARNING

Before operating your

machine, carefully read and

understand all safety, controls

and operating instructions in

this Manual, the separate

Engine Owner's Manual, and

on the decals on the machine.

Failure to follow these

instructions can result in

serious personal injury.

Forward ReverseClutch

ClutchBail Control

ulator

ight

Adjustment

Anti-ReverseStake

DrivePin

(on eachwheel)

Figure3-1: Featuresandcontrols.

Introduction

Thissectiondescribes thelocationsand

functions of thecontrols on your tiller.

Referto the next section ("Operation")

for detailedoperating instructions.

Practiceusing thesecontrols, with the

engine shut off, until you understand the

operationof the controls and feel

confident with eachof them,

IMPORTANT:Referto theseparate

engine manufacturer's EngineOwner's

Manualfor informationabout the

controls on theengine.

WheelDrivePins

WARNING

Never allow either of the

wheels to be in the

FREEWHEEL position when

the engine is running. Always

put both wheels in the WHEEL

DRIVE position before starting

the engine.

Failure to comply could cause

loss of tiller control, property

damage, or personal injury.

Eachwheel isequippedwith aWheel

Drive Pin (A,Figures 3-2 and 3-3) that

securesthe wheelto the wheelshaft (B).

Thewheelscan be positioned in either a

WHEELDRIVEor a FREEWHEELmode.

Beforestarting the engine,put both

wheels inthe WHEELDRIVEposition by

inserting theWheel Drive Pinsthrough

the wheelhubs and thewheel shaft, This

"locks" thewheelsto the wheel shaft,

causing the wheelsto turn when either

the ForwardClutch Bailor the Reverse

ClutchControl is engaged.

Usethe FREEWHEELmode only whenthe

engineis not running, In FREEWHEEL,

theWheel Drive Pinsare placedonly

through the holesin the wheel shaft (not

thewheel hubs), thus allowingthe wheels

to turn freely whenthe tiller is pushed or

pulled by hand,

To Place theWheelsin WHEELDRIVEor

FREEWHEEL:

1. Stop the engine,disconnectthe spark

plug wire from the spark plug and allow

theengine to cool,

2. Raiseonewheeloff theground and

placea sturdy supportunder the

transmission.

3. Removethe wheeldrive pin (A,

WARNING

Do not place the tiller on its

side when changing the wheel

drive positions as doing so

could result in gasoline

leaking from the fuel tank.

Failure to follow this instruc-

tion could result in personal

injury or propertydamage.

Figures 3-2 and 3-3) byremoving the

hairpin cotter (C).

Section3: FeaturesandControls

4. FORWHEELDRIVEmode (Figure3-2):

Slidethe wheeloutward and alignthe

holesin the wheel hub (D, Figure3-2))

and the wheelshaft (B). Insertthe wheel

drive pin (A) through the wheelhub and

the wheelshaft, Securethe wheeldrive

pin with the hairpin cotter (C) by pushing

the hairpin cotter in asfar as it will go.

Repeatfor the other wheeland then

removethe support from beneaththe

transmission,

5. FORFREEWHEELmode (Figure3-3):

Slidethe wheelinward and insert the

wheeldrive pin (A, Figure3-3) only

through the hole in the wheel shaft (B).

Securethewheel drive pin with the

hairpin cotter (C)by pushing the hairpin

cotter in as far asit will go, Repeatfor the

other wheeland then remove the support

from beneaththe transmission.

Figure3-2: WHEELDRIVEposition,

Figure3-3: FREEWHEELposition.

ForwardClutchBail

TheForward ClutchBail (E, Figure3-4)

controls theengagementof forward drive

to the wheels and powerto the tines,

NOTE: Thewheelswill rotate in a forward

direction; the tines will rotatecounter-

clockwise(backwardtoward the operator),

To OperatetheForwardClutchBail:

1. Putthe wheels in theWHEELDRIVE

position(seethe following "WARNING"

statement).

2. Lift and holdthe bail againstthe

handlebar. Thewheels and tines will

rotate- and the tiller will moveina

forward direction.

3. Releasethe bail to disengage(stop)

thewheelsandtines. Forwardtiller motion

will stop (theengine will continue to run).

WARNING

Before starting the engine, be

sure that both wheels are in

the WHEEL DRIVE position.

See "Wheel Drive Pins" for

instructions.

Engaging the Forward Clutch

Bail or the Reverse Clutch

Control when the wheels are

not in the WHEEL DRIVE

position could allow the tines

to rapidly propel the tiller

forward or backward.

Failure to comply could cause

loss of tiller control, property

damage, or personal injury.

ReverseClutchControl

The ReverseClutchControl (F,Figure3-4)

controls the engagementof reversedrive

to thewheels and tines, This powered

reversing feature is usedfor maneuvering

the tiller only - neverengagethetines in

the ground while going in thereverse

direction.

To OperatetheReverseClutchControl:

1. Operateonlywhen the wheels arein

the WHEELDRIVEposition (seethe

"WARNING"statement atthe left).

2. Stopall tiller motion by releasingthe

ForwardClutch Bail.

3. Lift up thehandlebar until the tines

clear the ground, look behind you to avoid

anyobstacles,and then pull the reverse

clutch control knobtoward you. The

wheels will rotate in a reversedirection.

4. Releasethe reverseclutch control

knobto disengage(stop) the wheels and

tines, All reversemotion will stop (the

engine will continue to run),

WARNING

• Use extreme cautionwhen

reversing or pulling the

machine towards you. Look

behind to avoid obstacles.

• Never attempt to till in

reverse.

Failure to follow this warning

could result in personal injury

or propertydamage.

Figure3-4:ForwardClutchBail(E)andReverse

ClutchControl(F).

Section3: FeaturesandControls

DepthRegulatorLever

Thislever (G,Figure3-5) controls the

tilling depthof the tines, Pull the lever

straight backand slideit up or down to

engagethe notched height settings.

Thehighest notch (lever allthe way

down) raisesthe tines approximately 1-

1/2"off the ground. This "travel" setting

allows the tiller to be movedwithout the

tines digging into the ground. Also use

this setting when starting the engine.

Move the lever upwardto increasethe

tilling depth, Thelowest notch allows a

tilling depthof approximately 6"-8",

dependingon soil conditions,

Forbest results, begin tilling at the

deepestdepthpossiblewithout causing

the tiller to bog down. Increasethe tilling

depthfrom one passover the soil to the

next.

Travel

Position

Figure3-5."Depthregulatorlever,

WARNING

• Place the Depth Regulator

Lever in the "travel"

position before starting the

engine. This position

prevents the tines from

touching the ground until you

are ready to begin tilling.

Failure to follow this warning

HandlebarHeightAdjustment

Thehandlebarheight is adjustableto

threedifferent settings (seeFigure3-6).

Asa general rule,adjust the handlebars

sothey areat waist levelwhen thetines

are3"-4"into thesoil.

ToAdjustthe Handlebars:

1. Stopthe engine, disconnectthe spark

plug wire from thespark plug and allow

theengine to cool,

2. Removethe screws, Iockwashersand

nuts, reposition the handlebars,and

reinstall the hardware.

Figure3-6."Handlebarheightadjustment.

Anti-ReverseStake

Thisstakeis locatedat the rear of the

transmission,under the tine hood (seeH,

Figure3-7). Its purposeis to automati-

cally help preventthe counter-rotating

tines from letting thetiller back up in the

direction of the operator if the tiller

wheels had beeninadvertently left in the

FREEWHEELposition. In this situation,

the Anti-ReverseStakewill be forced

down into theground, lifting the tines

upward out of the soil and helping

prevent backwardmotion of the tiller.

TheAnti-ReverseStakerequiresno adjust-

ment, but should be inspectedbefore

eachtiller use to verify that it swivels

freely. Removeanyclogged materials

(dirt, roots, rocks, etc.) that preventthe

Anti-ReverseStakefrom swinging freely.

Figure3-7:Anti-ReverseStake.

ENGINECONTROLS

could result in personal injury Referto theengine manufacturer's Engine

or propertydamage. Owner'sManual(includedin thetiller lit-

eraturepackage)to identify thecontrols

onyour engine.

IMPORTANT:Thecontrol for stopping the

engine is located on the engine.

Operation

WARNING

Before operating your

machine, carefully read and

understand all safety (Section

1), controls (Section 3) and

operating instructions (Section

4) in this Manual, in the

separate Engine Owner's

Manual, and on the decals on

the machine.

Failure to follow these instruc-

tions can result in serious

personal injury.

INTRODUCTION

Readthis Section of the manualthor-

oughly beforeyou start the engine, Then,

take thetime to familiarizeyourself with

the basic operation of thetiller before

using it in the garden, Findan open, level

areaand practiceusing the tiller controls

without the tines engaging the soil (put

tines in "travel" setting), Onlyafter

you've becomecompletely familiar with

the tiller should you begin using it in the

garden.

INITIAL OPERATION

Perform the following maintenanceduring

thefirst hours of newoperation (see

"Maintenance"section in this manualand

in the EngineOwner's Manual).

1. Changeengine oil after first 2 hours of

newengineoperation.

2. Checkfor looseor missing hardware

on unit, Tighten or replaceasneeded.

3. Checktension on forward drive belt

after first 2 hours of operation,

4. Checktransmission gearoil levelafter

first 2 hours of operation,

,Reverse ClutchControl

ForwardClutchBail

ulatorLever

Recoil Starter

Figure4-1

Wheel DrivePin

(on eachwheel)

STARTINGANDSTOPPINGTHE

ENGINE

Pre-StartChecklist

Makethefollowing checksand perform

the following services beforestarting the

engine,

1. Readthe"Safety" and "Controls"

sections in this manual. Readthe

separateEngineOwner's Manual

provided bythe engine manufacturer,

2. Checkthat the wheelsare in the

WHEELDRIVEposition (wheel pins must

bethrough the wheel hubsand the wheel

shaft holes).

3. Checkunit for looseor missing

hardware. Serviceas required,

4. Checkengine oil level. See Engine

Owner's Manual,

5. Checkthatall safety guards and

coversare in place,

6. Checkair cleanerand enginecooling

system, SeeEngineOwner's Manual.

7. Attach spark plug wire to spark plug.

8. Fill thefuel tank with gasoline

according to the directions in the

separateEngineOwner's Manual. Follow

all instructions and safety rules carefully.

DANGER

GASOLINE IS HIGHLY

FLAMMABLE AND ITS

VAPORSARE EXPLOSIVE.

Followgasolinesafetyrulesin

this manual (see Section 1)

and in the separate Engine

Owner'sManual.

Failure to follow gasoline

safety instructionscan result

in serious personal injury

and property damage.

Section4: Operation

Startingthe Engine

Thefollowing stepsdescribe how to start

and stop theengine. DOnotattemptto

engagetines or wheels untilyouhave

read all the operatinginstructionsinthis

Section. Also review thesafetyrules in

Section1: "Safety" andthetiller and

engine controlsinformationin Section

3: "Features andControls."

CAUTION

To help prevent serious

personal injury or damage to

equipment:

• Before starting engine, put

both wheels in the WHEEL

DRIVE position. Never have

the wheels in the

FREEWHEEL position when

the engine is running. When

the wheels are in

FREEWHEEL, they do not

hold back the tiller and the

tines could propel the tiller

rapidly backward.

• Before starting engine, put

Forward Clutch Bail (all

Models) and Reverse Clutch

Control in neutral (disen-

gaged) positionsbyreleasing

levers.

• Never run engine indoors or

in enclosed, poorly venti-

lated areas. Engine exhaust

contains carbon monoxide,

an odorlessand deadly gas.

*Avoid engine muffler and

nearby areas. Temperatures

in these areas may exceed

150OF.

1. Completethe"Pre-Start Checklist" on

theprevious page.

2. PutthewheelsintheWHEELDRIVE

position (see"Wheel DrivePins"in

Section 3)+

3. Putthe DepthRegulator Leverin the

"travel" position (leverallthe waydown)

so that thetines areclear of the ground.

4. Releaseall controls on the tiller.

5. If engineis equipped witha fuel valve,

turn valveto open position asinstructed

intheseparateEngineOwner's Manual.

6. Put ignitionswitch and/or throttle

control leveron enginein "ON," "RUN,"

"FAST"or "START" positionas instructed

in the separateEngineOwner's Manual.

7. Chokeor primeengineas instructed in

theseparateEngineOwner's Manual.

8. Placeone hand on the fueltank to

stabilizethe unit whenyou pullthe starter

handle. Usethe recoil starter ropeto start

theengine asinstructed in the separate

EngineOwner's Manual. When engine

starts,gradually movechoke lever(on

enginesso equipped)to "NOCHOKE,"

"CHOKEOFF"or "RUN" position.

WARNING

Hot surfaces can causesevere

burns. Do not touch muffler or

adjacent areas.

9. Usethe"FAST"throttlespeedsetting

whentilling.

WARNING

Keep away from rotating

tines. Rotating tines will

cause injury.

Stoppingthe EngineandTiller

1. To stop the wheelsand tines, release

theForward Clutch Bail or the Reverse

ClutchControl -- whichevercontrol is in

use.

2. To stop the engine,put the throttle

control leveron enginein "OFF"or

"STOP"position.

OPERATINGTHETILLER

Thefollowing pagesprovide guidelinesto

using your tiller effectivelyand safelyin

various gardening applications. Besure

to read "Tilling Tips & Techniques" in this

Section beforeyou actually putthe tines

into the soil.

This is a CRT(counter-rotating tine) tiller.

Asthe wheels pull forward, thetines

rotate backward.

Thiscreatesan "uppercut" tine action

which digs deeply,uprooting soil and

weeds. Don't overloadthe engine,but dig

asdeeplyas possible on eachpass. On

later passes,thewheels may tend to spin

in thesoft dirt. Helpthem along by lifting

up slightly on the handlebar(palm facing

up).

1. Followthe"Pre-Start Checklist" onthe

previous page. Besure that the wheels

are in the WHEELDRIVEposition.

2. Put theDepth Regulator Leverin the

"travel" position (leverall the way down)

so that the tines are clear of the ground.

Usethis position when practicing with

your tiller or when moving to or from the

garden. When you are readyto begin

tilling, you must move the Depth

Regulator Leverto the desireddepth

setting (see"Tilling Tips & Techniques").

Checkthat theAnti-Reverse Stakeswivels

freelybackand forth. Removeanyclogged

material on or around thestake.

Figure4-2: Useonehandtoguidetiller

whenmovingforward.

3. Starttheengine andallow itto warm

up. When warm, putthrottle control in

fast speedsetting.

4. Forforward motion of wheelsand

powerto the tines:

(a) Pull the Forward ClutchBail up and

hold it againstthe handlebar. Release

the bail to stop forward motion of

thewheels and powerto the tines.

(b) Asthe tiller movesforward, relaxand

letthewheelspulltheunit alongwhile

the tines dig. Walk behindand a

little to one side of thetiller. Usea

light but securegrip with one hand

on the handlebars,keepingyour arm

loose. SeeFigure4-2.

Section4: Operation

WARNING

Do not push down on the

handlebars to try to make the

tiller till more deeply. This

prevents the wheels from

holding the tiller back and can

allow the tines to rapidly

propel the tiller backward

toward the operator, which

could result in loss of control,

property damage, or personal

injury.

Letthetiller move at its own paceand do

not push down on the handlebarsto tryto

dig deeper- this takesweight off the

wheels,cuts traction, andcausesthetines

to try and propel the tiller.

5. Forreversemotion of thewheels and

tines:

(a) Lookbehind andexercisecaution

when operating in reverse. DOnet

till while in reverse.

(b) Stop all forward motion before

reversing, Lift the handlebarswith

one hand until the tines are off the

ground and thenpull the Reverse

ClutchControl knob out to engage

reversemotion (seeFigure4-3). To

stop reversemotion, let go of the

ReverseClutch Control knob.

6. To Turn theTiller Around:

(a) Practiceturning the tillerin a level,

open area. Be very careful to keep

your feetand legsawayfrom the

tines,

(b) To makea turn, lift the handlebars

until theengine and tines are

balancedover the wheels (Figure

4-4). Thetines must be out of the

ground while turning the tiller.

sideways on the handlebarto move

the tiller in the direction of the turn

(Figure4-5). After completing the

turn, slowly lower the tines into the

soil to resume tilling.

Figure4-3: Raise tinesoff groundand look

behind whenmovingin reverse.

WARNING

Before tilling, contact your

telephone or utilities company

and inquire if underground

equipment or lines are used in

your area. Their representa-

tive will be glad to answer

your questions and tell you if

any of their equipment or lines

are buried underground on

yourproperty.

Turningthe TillerAround

Figure4-4: Tobeginturn,lift handlebars

untilengineandtinesarebalancedover

wheels.Besuretinesareoutofground.

Figure4-5: Withtiller balancedover

wheels(and tinesoutof theground),push

handlebarssidewaystoturn tiller.

StoppingtheTiller andEngine

1. To stop thewheels and tines, release

the ForwardClutch Bailor the Reverse

Clutch Control - whichever is engaged.

2. To stop theengine, movethe throttle

control leveron engineto "OFFIIor

"STOP"position.

Section4: Operation

TillingTips& Techniques

Letthetiller dothe work

• Whiletilling, relaxandlet thewheels

pull the tiller along whilethe tinesdo

the digging. Walk on the side that is

not yet finished (to avoid making foot-

printsin the freshly tilled soil) and

lightly, but securelygrip the handlebar

with just one hand,SeeFigure4-2.

•Avoid the temptation to push down on

the handlebarsin an attemptto force

the tiller to dig deeper. Doing so takes

the weight off the poweredwheels,

causing them to lose traction. Without

the wheels helping to hold the tiller

back, thetines will attempt to propel

the tiller backwardtoward the

operator- often causing thetiller to

skip rapidly acrossthe ground,

Tilling depths

•When preparing the soil, till a fresh

pathon eachpass ratherthan overlap-

ping passes, Thisgives the wheels

maximum traction on undisturbed soil.

SeeFigure4-6. Digasdeeplyas

possible on eachpasswithout over-

loading theengine, Later passescan

be overlapped, (Watering thegarden

area afew days prior to tilling will

make tilling easier,as will letting the

newly worked soil set for a day or two

before making a final, deeptilling

pass.)

•Whencultivating (breakingup the

surfacesoil around plantsto help

destroyweeds),adjust thetines to dig

only 1-1/2"to 2"deep, Using shallow

tilling depthshelpspreventinjury to

plantswhoseroots often growcloseto

the surface, ff needed,lift up onthe

handlebarsslightly topreventthetines

from digging toodeeply. Cultivatingon

a regularbasisnotonlyeliminates

weeds,it alsoloosensandaeratesthe

soil for bettermoistureabsorptionand

fasterplantgrowth,

Avoidtilling soggy,wetsoil

Tilling wet soil often results in large,

hard clumps of soil that can interfere

with planting. If time permits, wait a day

or two after heavyrainsto allow the soil

to dry beforetilling, Test soil by

squeezing it into a ball, If it compresses

too easily,it is too wet to till.

Avoidmaking footprints

Wheneverpossible,walk on the untilled

side of theunit to avoidmaking foot-

prints in your freshlytilled or cultivated

soil. Footprintscausesoil compaction

that can hamperroot penetrationand

contribute to soil erosion. Theycanalso

"plant" unwantedweedseedsbackinto

the freshlytilled ground,

Choosingcorrectwheel

andtine speeds

With experience,you will find the'_just

right" tilling depth and tilling speed

combination that is best for your

garden,

Set theengine throttle leverat a high

enough speedto give the engine

adequatepowerand yet allow it to

operatewithout overloading it. Fastest

engine speedsmay bedesirablewhen

making final passesthrough the

seedbedor when cultivating. Selection

of thecorrect enginespeed, in relation

to thetilling depth, will ensurea suffi-

cient power levelto do thejob without

causing the engineto labor.

Suggestedtilling patterns

• Whenpreparing a seedbed,go over

the same pathtwice in the first row,

then makeindividual passesright next

to eachother (seeFigure4-6), When

finished in onedirection, makesecond

passesata right angle asshown in

Figure4-7,

In very hard ground it may takethree

or four overlapping passesto thor-

oughly pulverizethe soil, (SeeFigure

4-8.)

• If thegarden sizewill not permit

lengthwiseand then crosswise tilling,

then overlapthe first passesby one-

halfa tiller width, followed by succes-

sive passesat one-quarterwidth (see

Figure4-8).

•With planning, you canallow enough

room between rows to cultivate (see

Figure4-9). Leaveroom for the hood

width, plus enough extra room for

future plant growth.

Figure4-6

Figure4-7

Figure4-8

Figure4-9

Section4: Operation

TillingTips& Techniques

Clearingthetines

Dry grass, stringy stalks or tough vines

may become tangledin thetines. Follow

these proceduresto help avoidtangling

and to cleanthe tines, if necessary.

• Toreducetangling, set the depth

regulator to maximum depth.

• Whiletilling, try swaying the handle-

barsfrom sideto side (about6" to 12").

This "fishtailing" action often clears the

tines of debris.

• If tangling occurs, lift the tines out of

thesoil and run the tiller in reversefor

a few feet, This may unwind a good

dealof debris.

• It may be necessaryto remove the

debris by hand (a pocket knifewill help

youto cut awaythe material).

WARNING

Before clearing the tines by

hand, stop the engine, allow

all moving parts to stop and

disconnect the spark plug

wire.

Failure to follow this warning

could result in personal

injury.

Tilling onslopes

If you must garden on a moderate slope,

pleasefollow two very important guide-

lines:

1.Till only on moderate slopes, neveron

steepground wherefooting is difficult

(review safety rules in the "Safety"

sectionof this manual).

2.We recommend tillingup and down

slopes ratherthan terracing, Tilling

vertically on a slopeallows maximum

planting areaand also leavesroom for

cultivating,

IMPORTANT:Whentilling on slopes, be

surethe correct oil levelis maintained in

the engine (checkevery one-haff hour of

operation). Theincline of the slopewill

cause the oil to slant awayfrom its

normal leveland this canstarve engine

parts of required lubrication. Keepthe

engine oil levelat the full point atall

times!

A. Tilling upand downslopes:

•To keepsoil erosion to a minimum, be

sure to add enough organicmatter to

the soil so that ithas good moisture-

holding texture and try to avoid leaving

footprints or wheelmarks.

•When tillingvertically, try to makethe

first passuphill as thetiller digs more

deeplygoing uphill than it does

downhill, In soft soil or weeds,you

may haveto lift handlebarsslightly

while going uphill.

B. Tilling acrossslopeswithout

usingterraces:

If previouslydescribed tilling methods

aren't practicalfor you, thenyou cantill

laterallyacross a slope. However,we

don't reallyrecommendthis method as

it cancreate unsurefooting and invites

soilerosion.

Section4: Operation

LOADINGANDUNLOADINGTHE

TILLER

WARNING

Loading and unloading the

tiller into or from a vehicle is

potentially hazardous. We

don't recommend doing so

unless absolutely necessary,

as this couldresult in person-

al injury or properly damage.

However, if you must load or

unload the tiller, follow the

guidelines given next.

• Beforeloading or unloading, stop the

engine,waitfor all parts to stop

moving, disconnect thespark plug wire

and letthe engine and muffler cool,

• Thetiller istoo heavyand bulky tolift

safelyby one person. Two or more

peopleshould sharethe load,

• Usesturdy ramps and manually (engine

shut off) rollthe tiller into and out of the

vehicle. Two or more people areneeded

to do this.

• Rampsmust be strong enough to

support the combined weight of the tiller

and any handlers.The ramps should

providegood traction to prevent

slipping; they should haveside rails to

guide the tiller along the ramps;and

they should havea locking device to

secure them to thevehicle.

•The handlersshould wearsturdy

footwear that willhelp to prevent

slipping.

• Position the loading vehicleso that the

rampangle is as flat as possible (the

less inclineto the ramp, the better).

Turn the vehicle'sengine off and apply

its parkingbrake.

•When going up ramps, stand in the

normal operating position and pushthe

tiller aheadofyou. Havea personat

eachside to turn the wheels,

• Whengoing down ramps, walk

backwardwith thetillerfollowing you,

Keepalertfor anyobstacles behind you.

Position a personat eachwheel to

control the speedof thetiller, Nevergo

down ramps tiller-first, as thetiller could

tip forward.

• Usewooden blocks to placeon the

downhill sideof the wheels if you need

to stop the tiller from rolling down the

ramp, Also, usethe blocks to temporar-

ily keepthetiller in placeon theramps

(if necessary),and to chock the wheels

in placeafter the tiller is in the vehicle,

• Whenthe tiller is in the vehicle,prevent

it from rolling by chocking the wheels

with blocks and securelytie the tiller

down.

Maintenance

WARNING

Before inspecting,

cleaning or servicing the

machine, shut off engine,

wait for all moving parts to

come to a complete stop,

disconnectspark plug wire

and move wire away from

spark plug.

Failure to follow these

instructions can result in

serious personal injury or

propertydamage.

REQUIRED MAINTENANCE SCHEDULE

Before Every Every As

PROCEDURE Each 10 30 Noted

Use Hours Hours

Checkengine oil level

Cleanengine

Checkdrive belttension

Checknuts and bolts

Changeengine oil

Lubricate tiller

Serviceengine air cleanersystem

Checkgearoil levelin

transmission

Checktines for wear

Checkair pressure in tires

(if pneumatic)

Service spark plug

CheckAnti-ReverseStake

And every 5

operating hours

* Changemore frequently in dusty or dirty conditions. Changeafter first 2 hours of

break-in operation.

t Checkafter first2 hours of break-inoperation.

• SeeEngineOwner'sManualforserviceintervalsandinstructions.

Section5: Maintenance

WARNINGBefore inspecting,cleaning or servicingthe unit, shutoff engine, wait for all i_

partsto cometo a completestop,disconnectspark plugwire and movewire away from spark ..,Lol

plug. Failure to follow these instructions can result in serious personal injury or

propertydamage.

TILLERLUBRICATION

Proper lubrication of the tiller is an

essentialpart of maintenance. After

every 10 operating hours, oil or grease

the lubrication points shown in Figures

5-1 and 5-1A and described below.

Usea good quality lubricating oil (#30

weight engineoil is suitable) and aquality

generalpurposegrease(with a metal

lubricant, ifavailable).

• Removewheels,cleanwheel shaft (A,

Fig, 5-1) and apply thin coating of

greaseto the shaft.

• Greaseback,front and sides of depth

regulator lever(B, Fig.5-1).

• Removetines, cleantine shafts (C,Fig.

5-1)+Inspectfor rust, rough spots or

burrs (lookaround holes). Fileor sand

smooth, coat ends of shaft with grease.

• Oil the threads on the handlebarheight

adjustment screws andthe handlebar

attaching screws (D, Fig.5-1).

• ShiftingMechanism,Lightlyoil pivot

pointsforsmoothoperation(E,Fig.5-1A).

A C

Figure5-1

Figure5-1A

CHECKFOROILLEAKS

Beforeeachuse,checkyour tiller for

signs of an oil leak- usually a dirty, oily

accumulation either on the unit or on the

floor where it hasbeenparked,

A little seepagearound a cover or oil seal

is usually not a cause for alarm. However,

if the oil drips overnight then immediate

attention is neededasignoring a leakcan

result in severetransmission damage.

If a coveris leaking, try tightening any

loosescrews. If the screws aretight, a

newgasketor oil sealmay berequired. If

the leakis from around ashaft and oil

seal,the oil sealprobablyneedsto be

replaced. Seeyour authorizeddealer or

contact the factory for serviceor advice.

IMPORTANT:Neveroperatethetiller if

thetransmissionis low on oil. Checkthe

oil levelafter every30 hours of operation

and wheneverthere is anyoil leakage.

CHECKHARDWARE

Checkfor looseor missing hardwareafter

every 10 operating hours, Tighten or

replacehardwarebeforeusing the tiller.

Besure to checkthe screws underneath

thetiller hood (lift the hood flap) that

securethe transmission cover andthe

depth regulator leverto the transmission.

CHECKTIREPRESSURE(on

machines equipped with

pneumatic tires)

Checkthe air pressurein both tires.

Deflateor inflate both tires evenlyfrom

15-to-20 PSI (pounds per squareinch).

Besure that bothtires havethe sameair

pressure or the unit will tend to pullto

one side.

NOTE:Your tillermay not beequipped

with pneumatictires, eliminating the need

for air pressurechecks,

TRANSMISSIONGEAROILSERVICE

Checkthe transmission gear oil levelafter

every30 hours of operation or whenever

you notice anyoil leak. Operatingthe

tiller when the transmission is low on oil

canresult in severedamage.

A. To Checkthe Transmission

GearOil Level:

1. Checkthe gearoil levelwhen the trans-

mission is cool, Gearoil will expandin

warm operating temperatures and this

expansionwill provide an incorrect oil

levelreading.

2. With thetilleron level ground, adjust

theDepth RegulatorLeverup or down to

the notch that makesthetiller level,.

3. Removethe oil fill plug (A,Fig. 5-2)

from the transmission housingand look

into the oil fill hole. You will seethe main

drive shaft on one sideof the hole.

4. Thegear oil levelis correct ifthe gear

oil is approximately half wayup the side

of the drive shaft.

5. Ifthe gearoil levelis low, add gear oil

asdescribed next. If the gearoil levelis

okay,securely replacethe oil fill plug.

IMPORTANT:Do not operatethetiller if

thegear oil level is low. Doing so will

result in severedamageto the transmis-

sion components.

6. Ifadding only afew ouncesof gear

oil, use APIratedGL-4 or GL-5 transmis-

sion gearoil havinga viscosity of SAE

140, SAE85W-140 or SAE80W-90. If

refilling an empty transmission, useonly

GL-4 transmission gear oil havinga

viscosity of SAE85W-140 or SAE140.

NOTE:Do not useautomatic transmission

fluid or engine oil in the transmission.

7. Whilecheckingfrequently to avoid

overfilling, slowly add gear oil intothe oil

fill hole until it reachesthe halfway point

on the drive shaft.

8. Securely replacethe oil fill plug,

Page is loading ...

Troy-Bilt 21A-644H063 Owner's manual

Brand: Troy-Bilt

Model: 21A-644H063

Category: Mini tillers

Type: Owner's manual

This manual is also suitable for

Download PDF

report

Troy-Bilt 21A-644H063 Owner's manual

This manual is also suitable for

Troy-Bilt 21A-644H063 Owner's manual

Related papers

Other documents