Goal Zero Yeti Lithium MPPT User manual

Brand: Goal Zero

Model: Yeti Lithium MPPT

Type: User manual

This manual is also suitable for

YETI MPPT

Goal Zero Yeti Lithium MPPT

The Goal Zero Yeti Lithium MPPT is a 25 Amp MPPT charge controller with multiple ports for charging Goal Zero Yeti Lithium models. It features an MPPT (Maximum Power Point Tracker) that optimizes the power source to maximize power, resulting in up to 40% faster charge times, especially from solar panels.

Capabilities:

Charges the following Goal Zero Yeti models:
- Yeti 1000
- Yeti 1400
- Yeti 3000
Ports:
- 8mm Charging port: 14 - 22V, Do not exceed 150W per port
- Power Pole charging port: 14 - 22V
Do not exceed 22V input under standard use

Goal Zero Yeti Lithium MPPT

Capabilities:

Charges the following Goal Zero Yeti models:
- Yeti 1000
- Yeti 1400
- Yeti 3000
Ports:
- 8mm Charging port: 14 - 22V, Do not exceed 150W per port
- Power Pole charging port: 14 - 22V
Do not exceed 22V input under standard use

Page is loading ...

Please save these instructions

Read all the instructions and cautions before

beginning installation.

Do NOT disassemble or attempt to repair the module.

Do NOT allow water to enter the module, or the Goal Zero

Yeti Lithium.

Make sure all connections are tight and secure before using.

Do NOT exceed 22V (350W) input for the module; this can

cause serious damage to the Yeti Lithium and potential

bodily injury. Check third party solar panels specs before

attempting to use them with the module.

Do NOT chain solar panels in series (connecting positive

to negative, positive to negative, etc.), as this can result in

dangerously high levels of voltage that can cause serious

damage to the Yeti Lithium and

potential bodily injury.

Use ONLY with appropriate Goal Zero Yeti Lithium

Portable Power Stations.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: Do not exceed 22V input for the module under standard

use. Doing so can cause serious damage to the Yeti Lithium and

potential bodily injury. Take note of voltages when using third party

solar panels with the module. Do not chain solar panels in series

(positive to negative, positive to negative, etc.), as this can result in

dangerously high voltages.

WARNING: Never connect a power source to the module before

installing into the Yeti Lithium. Always connect the module to the Yeti

Lithium before connecting any power source.

GET TO KNOW YOUR GEAR

Data Transfer Connector

Anderson Power Pole Input

2 x 8mm Inputs

Indicator Light

Blue Connector

Table of Contents

Important Safety Instructions 1

Get To Know Your Gear 3

How It Works 4

Frequently Asked Questions 6

Technical Specifications 7

Français 8-13

Deutsch 14-19

Español 20-25

HOW IT WORKS

Tools you’ll need: Screwdriver

1. Turn off all the output ports and unplug the Yeti Lithium from any

power source.

2. Open the lid of the Yeti Lithium and remove the expansion module

carriage from the Yeti by removing the six screws and sliding out

the carriage.

a. Use both hands to work the expansion module carriage out of

its position.

3. Take note of the positive and negative terminals on the Yeti’s port, as

well as on the blue connector. Insert the blue module connector into the

module port on the Yeti Lithium, matching positive to positive, negative

to negative.

4. Insert the data transfer connector on the module into the data transfer

port on the Yeti Lithium.

5. Gently set in the Solar Charging Optimization Module into place, tucking

the cables into the opening.

6. Using the provided four screws, secure the module into place.

7. Using the APP or 8mm ports, plug the power source into the module.

8. Know the MPPT is working when the indicator light turns blue.

WARNING: Never connect a power source to the module before

installing into the Yeti Lithium. Always connect the module to the Yeti

Lithium before connecting any power source.

WARNING: Do not exceed 22V input for the module under standard

use. Doing so can cause serious damage to the Yeti Lithium and

potential bodily injury. Take note of voltages when using third party

solar panels with the module. Do not chain solar panels in series

(positive to negative, positive to negative, etc.), as this can result in

dangerously high voltages.

Black Cable (-)

Red Cable (+)

Blue Connector

Data Transfer

Connector

TECHNICAL SPECIFICATIONS

25 Amp MPPT Charge Controller

Charges the following: Approx. Charge time:

GOAL ZERO Yeti 1000 @ Max Input 3.5 hrs

GOAL ZERO Yeti 1400 @ Max Input 5 hrs

GOAL ZERO Yeti 3000 @ Max

Input

10 hrs

Ports: Do not exceed 22V input under standard use

8mm Charging port 14 - 22V, Do not exceed

150W per port

Power Pole charging port 14 - 22V

Expansion Module Connector

(Output)

25A MPPT charge controller

General:

Weight 1.3 lbs (583 g)

Dimensions 10.25 x 3.3 x 1.5 in (26 x

8.4 x 3.8 cm)

Warranty 12 months

Certs

FREQUENTLY ASKED QUESTIONS

Q: How many solar panels can I plug into the module?

A: There are three inputs on the module that can be used at the same time;

however, do not exceed more than 22V under standard use, as this

can result in damage to the Yeti Lithium and potential bodily injury. We

recommend chaining solar panels in parallel (positive to positive, negative

to negative, etc). We’ve taken the guesswork out of chaining when using

Goal Zero Boulder Solar Panels, the 8mm blue-ringed connector and

combiner cables properly chain our panels together for approved use

with the Yeti Portable Power Stations. Please call our solar experts at

888-794-6250.

Q: Can I plug solar panels into the module and the Goal Zero Yeti Lithium

input ports at the same time?

A: Yes; however, we recommend using the module’s inputs for solar panels

since it can optimize the charging efficiency up to 40%. You may even

notice up to 20% more efficiency when charging the Yeti Lithium from

the wall when using the module.

Q: Can I use non-Goal Zero Solar Panels or a custom wiring solution or any

solar configuration that may be over 22V open circuit voltage

A: Please call our solar experts at 888-794-6250.

Yeti Lithium MPPT Expansion Module

INDICATOR LIGHT

FLASHING BLUE – Battery Charging

BLUE – Battery Full

NO LIGHT – Off

FLASHING RED – Input over voltage, unit over temperature, or

improper connection

WHAT IS MPPT?

MPPT stands for Maximum Power Point Tracker. The Solar Charging

Optimization Module is an external MPPT and when installed properly,

actively monitors the energy source you’re using to charge the Goal Zero

Yeti Lithium and optimizes the source to maximize power, resulting in up to

40% faster charge times, especially from solar panels. You may also notice

better charge times from AC when utilizing the Yeti Lithium’s AC charging

cable plugged into the module.

Page is loading ...

SM110217

GOAL ZERO HEADQUARTERS

675 West 14600 South

Bluffdale, UT 84065

Designed in the U.S.A.

Made in China

1-888-794-6250

This equipment has been tested and found to comply with the limits for a Class

B digital device, pursuant to part 15 of the FCC Rules. These limits are designed

to provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television reception,

which can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the following

measures:

—Reorient or relocate the receiving antenna.

—Increase the separation between the equipment and receiver.

—Connect the equipment into an outlet on a circuit different from that to which

the receiver is connected.

—Consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the

following two conditions: (1) This device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that

may cause undesired operation.

Goal Zero Yeti Lithium MPPT User manual

Brand: Goal Zero

Model: Yeti Lithium MPPT

Type: User manual

This manual is also suitable for

YETI MPPT

Goal Zero Yeti Lithium MPPT

Capabilities:

Charges the following Goal Zero Yeti models:
- Yeti 1000
- Yeti 1400
- Yeti 3000
Ports:
- 8mm Charging port: 14 - 22V, Do not exceed 150W per port
- Power Pole charging port: 14 - 22V
Do not exceed 22V input under standard use