George Kovacs P1383-077-L User manual

Brand: George Kovacs

Model: P1383-077-L

Type: User manual

George Kovacs P1383-077-L is a wall-mounted light fixture that provides ample lighting for various indoor spaces. Its adjustable arm allows you to direct light precisely where needed, making it suitable for reading, task lighting, or accentuating artwork. The fixture's sleek design complements modern and contemporary decors, adding a touch of sophistication to any room. With its easy installation process, you can quickly and effortlessly enhance the ambiance of your living space.

IMPORTANT: Fixture should be installed by a qualified

electrician to ensure proper wiring and installation.

Dimmable with ELV dimmer switches.

INSTALLATION INSTRUCTIONS FOR P1382-077-L/P1383-077-L/P1384-077-L

For Wall Mount Fixture

WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER.

AVE RT I SS E ME N T ! CO U P E R L E C O U RA NT A U N I V E AU D E S FU S I B L E S O U D O D I SJ O N C TE U R.

AV E R T I S S E M E N T ! C O U P E R L E C O U R A N T A U N I V E A U D E S F US I B L E S OU D O D IS J O N C T EU R .

PREPARATION

1. Shut off power at the fuse box or circuit breaker box. If

necessary remove the old fixture and mounting hardware.

2. Carefully unpack your new fixture and lay out all the parts

on a clear area. Take care not to lose any small parts

necessary for installation.

MOUNTING THE FIXTURE (FIG. 1)

3. Align the glass (K) to the metal arm (I), tighten with washer

(J), gasket (O) and screw (L). Fix the metal arm (I) to the

bracket (N) by screw (M). Use the “key holes” located on

the mounting plate (B) as a template to mark the location of

the plastic anchors (D) and pre-drill two holes

4. Install the plastic anchors (D) into the wall.

5. Secure mounting plate (B) to junction box (A) using

junction boxes screws (C) (Size: 8-32*1/2”L). The side of

the mounting back plate marked “GND” must face out.

6. Align the “key holes” on the mounting plate (B) to the

plastic anchors (D) and secure with screws (E).

CONNECTING THE WIRES (FIG. 2)

7. At this point, connect the electrical wires as shown in Fig. 2,

making sure that all wire connectors are secured. If your

outlet has a ground wire (green or bare copper), connect

the fixtures ground wire to it. Otherwise, connect the fixture

ground wire directly to the mounting plate (B) using the

green screw (G) provided. After wires are connected, tuck

them carefully inside the junction box.

COMPLETING THE INSTALLATION (Fig. 1)

8. Install the bracket (Z) into mounting plate (B) using screw

(H).

Your installation is now completed. Return power to the junction box

and test the fixture.

CAUTION /ATTENTION: When handling the fixture, do not

apply pressure to the LEDs. Hold the fixture by the base or

bracket.

Replacing LED module (Fig. 3)

The LED module can be replaced by a qualified electrician

without cutting of wire and without damage to any decorative

element to which the fixture is attached. See installation steps

for more details (Fig 3.)

a. Shut off power. Remove the fixture from the wall.

b. Remove the screw (P) to disconnect the heat sink (W) from

the bracket.

c. Remove screw (U) and use a pin to press the hole on the

quick connector (X) to disconnect LED module.

d. Reverse steps a-c for installing the new LED module.

Note: The LED module should be provided by a specified

supplier.

FIG.1

Set #

P1382-077-L : A-021-341113

P1383-077-L : A-021-564113A

P1384-077-L : A-021-803113

- Mounting plate - Ground screw

- Mounting screw*2pcs

Fig.3

Fig.2

FIXTURE

WIRES

Black or

Smooth

HOUSE

WIRES

Black

(Hot)

FIXTURE

WIRES

White or

Ribbed

HOUSE

WIRES

White

(Neutral)

FIXTURE

WIRES

Bare

Copper

(Ground)

HOUSE

WIRES

Green or

Bare

Copper(G

round)

George Kovacs P1383-077-L User manual

Brand: George Kovacs

Model: P1383-077-L

Type: User manual

Download PDF

report

George Kovacs P1383-077-L User manual

George Kovacs P1383-077-L User manual

Related papers

Other documents