George Kovacs P1305-655-L User manual

Type
User manual
Page 1/2
Fig.1
D
E
F1
F2
G
Rod#
W30-1-077*3(F1)
W30-H-077*1(F2)
C
B
A
J
M
N
I
H
K
L
INSTALLATION INSTRUCTIONS FOR P1305-L
For LED Pendant
READ AND SAVE THESE INSTRUCTIONS
WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER
AVERTISSEMENT!COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DO DISJONCTEU
ASSEMBLING THE FIXTURE (Fig.1, Fig. 2)
1 Shut off power at the fuse box or circuit breaker. If necessary, remove the old
fixture including the mounting hardware.
2 Carefully remove the fixture from the carton and check that all parts are included
as show in Figure 1.
3 Loosen screws (D) and remove mounting plate (A) from canopy (E). Attach
mounting plate (A) (Part# LTG BKT10) to the junction box using mounting screws
(B) (size:8-32*1/2L).
4 This fixture includes three 12" and one 6" rod. Determine the desired hanging
height and thread rods (F1/F2) to nipple (G). Pass the wires carefully through
each rod during assembly. Next place canopy (E) over rods (F) and thread
hanger ball (C) to rod (F). Please remove the nipple if installing with one 6" rod
only.
5 Run safety cable through a slot located in mounting plate (A) one circle, then lace
the safety cable through the set screws assembly and secure with screw close to
the hanger ball with the length desired.
6 While holding the fixture body, install the fixture into the mounting plate (A) by
tilting at a slight angle so that the hanger ball (C) slips into the mounting plate (A)
as shown. Align the notch in the hanger ball (C) to the tab on the mounting plate
(A) to prevent the fixture from turning.
CONNECTING THE WIRES (Fig. 3)
7 At this point, connect the electrical wire as shown in figure 3, making sure that all
wire connectors are secured. If your outlet has a ground wire (green or bare
copper), connect the ground wire from the hanger ball and mounting plate to it.
Otherwise, connect the ground wire from hanger ball directly to the mounting
plate ground wire and secure with wire connectors provided. After the wires are
connected, tuck them carefully into the ceiling junction box.
FINISHING THE INSTALLATION (Fig.1)
1 Align canopy (E) over mounting plate (A) and secure with screws (D).
2 Secure frame (J) to pan (I) with screws (H).
3 Thread rod (L) to joint (K). Align glass (M) to the frame and secure with finial (N).
Your installation is now complete. Return power to the junction box and test the fixture.
CAUTION/ATTENTION: When handling the fixture, do not apply pressure to the LEDs.
Hold the fixture by the base only.
Replacing LED module (Fig. 4)
The LED module can be replaced by a qualified electrician without cutting of wire and
without damage to any decorative element to which the fixture is attached. See
installation steps for more details (Fig. 4)
Warning: Turn off power at the circuit breaker before replacing LED module.
a. Loosen finial (N) and remove glass (M).
b. Loosen screws (U) and remove gasket (T), glass (S).
c. Loosen screws (Q), spacer (R), and remove gasket (P). Carefully remove LED
module (O) from pan (I) and disconnect the wire using screwdriver from wire
connector.
d. Reverse steps a-c for installing the new LED module.
Note: The LED module should be provided by a specified supplier.
IMPORTANT: Fixture should be installed by a qualified electrician to ensure proper
wiring and installation.
Dimmable with ELV and/or LED compatible wall dimmer switches.
Fig.3
Fig.4
M
N
S
T
U
P
Q
O
R
Fig.2
Page 2/2
Canopy x 1
b.
Hardware Bag:
F1. ROD 12" x 3
F2. ROD 6" x 1
F1
F3
F
  • Page 1 1
  • Page 2 2

George Kovacs P1305-655-L User manual

Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI