LG AMNW24GTPA0 User manual

Brand: LG

Model: AMNW24GTPA0

Category: Split-system air conditioners

Type: User manual

www.lg.com

MFL67655308

Rev.02_071420

Please read this manual carefully before operating

your set and retain it for future reference.

4-WAY CEILING CASSETTE

OWNER’S MANUAL

AIR

CONDITIONER

ENGLISH

ESPAÑOL

PORTUGUÊS

TABLE of Contents

2 Ceiling Cassette-Type Air Conditioner

3 SAFETY INSTRUCTIONS

6 PRODUCT INTRODUCTION

6 Name and function of parts

6 What to do before operation

6 Operation Indication Lamps

7 OPERATING INSTRUCTION

7 Wireless Remote Controller

8 How to insert the Batteries

8 Wireless Remote Controller Maintenance

8 Operating Method

9 OWNER'S INSTRUCTION

9 Cooling Mode - Standard Operation

9 Cooling Mode - Power Cooling

10 Auto Operation Mode

11 Auto Changeover Mode

12 Auto Changeover Mode - Setting the Mode Change Temperature

13 Dehumidification Mode

14 Heating Mode

15 Fan Mode

16 TEMPERATURE SETTING/ROOM

TEMPERATURE CHECKING

17 AIRFLOW SETTING

17 Up/Down Airflow Direction Control (Optional)

17 Left/Right Airflow Direction Control (Optional)

18 SUB FUNCTION

18 Plasma Purification(Optional)

18 Auto Clean (Optional)

19 Smart Clean (Optional)

20 LCD Luminosity Control (Optional)

20 Celsius/Fahrenheit Switching

20 Electric heater (Optional)

21 Individual vane angle control (Optional)

22 TIMER

22 Setting the Current Time

22 Sleep Timer Setting

22 On Timer Setting

22 Off Timer Setting

22 To cancel the Timer Setting

23 MAINTENANCE AND SERVICE

23 Indoor Unit

24 Purifying filter(Optional)

25 Operation Tips!

25 When the air conditioner is not going....

26 Troubleshooting Tips! Save time and money!

26 Call the service immediately in the following situations

TABLE OF CONTENTS

Safety instructions

Owner's Manual 3

ENGLISH

Safety instructions

Installation

• Do not use a defective or underrated circuit breaker. Use this appliance on a dedicated circuit.

- There is risk of fire or electric shock.

• For electrical work, contact the dealer, seller, a qualified electrician, or an Authorized Service Center.

- Do not disassemble or repair the product. There is risk of fire or electric shock.

• Always ground the product.

- There is risk of fire or electric shock.

• Install the panel and the cover of control box securely.

- There is risk of fire or electric shock.

• Always install a dedicated circuit and breaker.

- Improper wiring or installation may cause fire or electric shock.

• Use the correctly rated breaker or fuse.

- There is risk of fire or electric shock.

• Do not modify or extend the power cable.

- There is risk of fire or electric shock.

• Do not install, remove, or re-install the unit by yourself (customer).

- There is risk of fire, electric shock, explosion, or injury.

• Be cautious when unpacking and installing the product.

- Sharp edges could cause injury. Be especially careful of the case edges and the fins on the condenser and

evaporator.

• For installation, always contact the dealer or an Authorized Service Center.

- There is risk of fire, electric shock, explosion, or injury.

• Do not install the product on a defective installation stand.

- It may cause injury, accident, or damage to the product.

• Be sure the installation area does not deteriorate with age.

- If the base collapses, the air conditioner could fall with it, causing property damage, product failure, and

personal injury.

• Do not turn on the breaker or power under condition that front panel, cabinet, top cover, control box cover are

removed or opened.

- Otherwise, it may cause fire, electric shock, explosion or death.

• Use a vacuum pump or Inert (nitrogen) gas when doing leakage test or air purge. Do not compress air or Oxygen

and Do not use Flammable gases. Otherwise, it may cause fire or explosion.

- There is the risk of death, injury, fire or explosion.

WARNING

The following safety guidelines are intended to prevent unforeseen risks or damage from unsafe or incorrect

operation of the appliance.

The guidelines are separated into ‘WARNING’ and ‘CAUTION’ as described below.

WARNING

This indicates that the failure to follow the instructions can cause serious injury or death.

CAUTION

This indicates that the failure to follow the instructions can cause the minor injury or damage to the

product.

This symbol is displayed to indicate matters and operations that can cause risk.

Read the part with this symbol carefully and follow the instructions in order to avoid risk.

Safety instructions

4 Ceiling Cassette-Type Air Conditioner

Operation

• Do not let the air conditioner run for a long time when the humidity is very high and a door or a window is left

open.

- Moisture may condense and wet or damage furniture.

• Take care to ensure that power cable could not be pulled out or damaged during operation.

- There is risk of fire or electric shock.

• Do not place anything on the power cable.

- There is risk of fire or electric shock.

• Do not plug or unplug the power supply plug during operation.

- There is risk of fire or electric shock.

• Do not touch(operate) the product with wet hands.

- There is risk of fire or electrical shock.

• Do not place a heater or other appliances near the power cable.

- There is risk of fire and electric shock.

• Do not allow water to run into electric parts.

- It may cause There is risk of fire, failure of the product, or electric shock.

• Do not store or use flammable gas or combustibles near the product.

- There is risk of fire or failure of product.

• Do not use the product in a tightly closed space for a long time.

- Oxygen deficiency could occur.

• When flammable gas leaks, turn off the gas and open a window for ventilation before turn the product on.

- Do not use the telephone or turn switches on or off. There is risk of explosion or fire.

• If strange sounds, or small or smoke comes from product. Turn the breaker off or disconnect the power supply

cable.

- There is risk of electric shock or fire.

• Stop operation and close the window in storm or hurricane. If possible, remove the product from the window

before the hurricane arrives.

- There is risk of property damage, failure of product, or electric shock.

• Do not open the inlet grill of the product during operation. (Do not touch the electrostatic filter, if the unit is so

equipped.)

- There is risk of physical injury, electric shock, or product failure.

• When the product is soaked (flooded or submerged), contact an Authorized Service Center.

- There is risk of fire or electric shock.

• Be cautious that water could not enter the product.

- There is risk of fire, electric shock, or product damage.

• Ventilate the product from time to time when operating it together with a stove, etc.

- There is risk of fire or electric shock.

• Turn the main power off when cleaning or maintaining the product.

- There is risk of electric shock.

• When the product is not be used for a long time, disconnect the power supply plug or turn off the breaker.

- There is risk of product damage or failure, or unintended operation.

• Take care to ensure that nobody could step on or fall onto the outdoor unit.

- This could result in personal injury and product damage.

Installation

• Always check for gas (refrigerant) leakage after installation or repair of product.

- Low refrigerant levels may cause failure of product.

• Install the drain hose to ensure that water is drained away properly.

- A bad connection may cause water leakage.

• Keep level even when installing the product.

- To avoid vibration or water leakage.

CAUTION

Safety instructions

Owner's Manual 5

ENGLISH

• Do not install the product where the noise or hot air from the outdoor unit could damage the neighborhoods.

- It may cause a problem for your neighbors.

• Use two or more people to lift and transport the product.

- Avoid personal injury.

• Do not install the product where it will be exposed to sea wind (salt spray) directly.

- It may cause corrosion on the product. Corrosion, particularly on the condenser and evaporator fins, could

cause product malfunction or inefficient operation.

• If anyone other than a licensed professional installs, repairs, or alters LG Electronics air conditioning products,

the warranty is voided.

- All costs associated with repair are then the full responsibility of the owner.

• Do not install the unit in potentially explosive atmospheres.

Operation

• Do not expose the skin directly to cool air for long periods of time. (Don't sit in the draft.)

- This could harm to your health.

• Do not use the product for special purposes, such as preserving foods, works of art, etc. It is a consumer air

conditioner, not a precision refrigeration system.

- There is risk of damage or loss of property.

• Do not block the inlet or outlet of air flow.

- It may cause product failure.

• Use a soft cloth to clean. Do not use harsh detergents, solvents, etc.

- There is risk of fire, electric shock, or damage to the plastic parts of the product.

• Do not touch the metal parts of the product when removing the air filter. They are very sharp!

- There is risk of personal injury.

• Do not step on or put anything on the product. (outdoor units)

- There is risk of personal injury and failure of product.

• Always insert the filter securely. Clean the filter every two weeks or more often if necessary.

- A dirty filter reduces the efficiency of the air conditioner and could cause product malfunction or damage.

• Do not insert hands or other objects through the air inlet or outlet while the product is operated.

- There are sharp and moving parts that could cause personal injury.

• Do not drink the water drained from the product.

- It is not sanitary and could cause serious health issues.

• Use a firm stool or ladder when cleaning or maintaining the product.

- Be careful and avoid personal injury.

• Replace the all batteries in the remote control with new ones of the same type. Do not mix old and new batteries

or different types of batteries.

- There is risk of fire or explosion.

• Do not recharge or disassemble the batteries. Do not dispose of batteries in a fire.

- They may burn or explode.

• If the liquid from the batteries gets onto your skin or clothes, wash it well with clean water. Do not use the remote

if the batteries have leaked.

- The chemicals in batteries could cause burns or other health hazards.

• If you eat the liquid from the batteries, brush your teeth and see doctor. Do not use the remote if the batteries

have leaked.

- The chemicals in batteries could cause burns or other health hazards.

• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental

capabilities, or lack of experience and knowledge unless they have been given supervision or instruction

concerning use of the appliance by a person responsible for their safety.

- Children should be supervised to ensure that they do not play with the appliance.

• The user must carry out checks and cleaning of routine to avoid defective performance.

- In a special situation, only service personnel can carry out repair work.

6 Ceiling Cassette-Type Air Conditioner

Product Introduction

1: Indoor unit

2: Outdoor unit

3: Remote controller

4: Inlet air

5: Discharge air

6: Refrigerant piping, connection

electric wire

7: Drain pipe

8: Ground wire

Wire to ground outdoor unit to

prevent electrical shocks.

Multi system

Pair system or simultaneous operation system

: Lights up during the system operation.

Filter Sign : Lights up after 2 400 hours from the time of first operating unit.

Timer : Lights up during Timer operation.

Defrost Mode : Lights up during Defrost Mode or Hot Start operation.(Heat pump model only)

On/Off

Forced

•

: To operate the unit when the remote control can't be used

for any reason.

What to do before operation

Name and function of parts

Product Introduction

• This function may not be supported, depending on the model.

• The feature can be changed according a type of model.

Operation Indication Lamps

If your installation has a customized

control system, ask your LG dealer for

the operation that corresponds to your

system.

1: Unit with remote controller

2: Unit without remote controller (when

used as simultaneous operation)

Owner's Manual 7

ENGLISH

Operating Instruction

Wireless Remote Controller

Cooling Mode

Auto Mode or Auto Changeover

Dehumidification mode

Heating Mode

Fan Mode

•

Cooling Model( ), Heat Pump Model( )

Operation Mode

VANE ANGLE Button

Used to set each vane angle.

FUNCTION SETTING Button

Used to set or clear Auto Clean, Smart Clean,

Electric heater or Individual vane angle control.

ON/OFF Button

Used to turn on/off the unit.

JET COOL Button

Speed cooling operates super high fan speed.

LEFT/RIGHT AIRFLOW Button (OPTIONAL)

Used to set the desired left/right(horizontal)

airflow direction.

UP/DOWN AIRFLOW Button

Used to stop or start louver movement and set

the desired up/down airflow direction.

ON TIMER Button

Used to set the time of starting operation.

SLEEP TIMER Button

Used to set the time of sleeping operation.

SET / CLEAR Button

Used to set/clear the timer.

Used to set the current time.(if it input for 3 s)

PLASMA Button (OPTIONAL)

Used to start or stop the plasma-purification

function.

ROOM TEMPERATURE SETTING Button

Used to select the room temperature.

OPERATION MODE SELECTION Button

Used to select the operation mode.

INDOOR FAN SPEED SELECTION Button

Used to select fan speed in four steps low,

medium, high and chaos.

ROOM TEMPERATURE CHECKING Button

Used to check the room temperature.

OFF TIMER Button

Used to set the time of stopping operation.

TIMER SETTING(Up/Down)/LIGHT Button

Used to set the timer.

Used to adjust the brightness.(if it is not time

adjust mode)

RESET Button

Used to reset the remote controller.

Operating Instruction

8 Ceiling Cassette-Type Air Conditioner

Operating Instruction

1. Choose a suitable place where its safe & easy

to reach.

2. Fix the holder to wall etc with the supplied

screws firmly.

3. Slide the remote controller inside the holder.

1. Remote controller should never be exposed to

direct sunlight.

2. Signal transmitter & receiver should always be

clean for proper communication. Use a soft

cloth to clean them.

3. In case some other appliances also get

operated with remote control, change their

position or consult your serviceman.

1. The signal receiver is inside the unit.

Aim the remote controller towards the unit to operate it.

There should not be any blockage in between.

1. Remove the battery cover by pulling it according to the arrow

direction.

2. Insert new batteries making sure that the (+) and (-) of battery are

installed correctly.

3. Reattach the cover by sliding it back into position.

1. Always use/replace both batteries of same type.

2. If the system is not to be used for a long time, remove the

batteries to save their working life.

3. If the display screen of remote controller starts, fading replace

both of the batteries.

Operating Method

Wireless Remote Controller Maintenance

How to insert the Batteries

Accessory

Holder(1 EA) Fixing Screw (2 EA) Owner's / Installation

Manual

Owner's Instruction

Owner's Manual 9

ENGLISH

Press the ON/OFF button.

The unit will respond with beep sound.

Press MODE button to select Cooling Mode.

To lower the temperature

To raise the temperature

Set the desired temperature by pressing TEMP button.

Press ROOM TEMPERATURE CHECKING button to

check the room temperature. When setting the desired

temperature is higher than room temperature, cooling

wind isn’t blow out.

h Setting Temp. Range : 18~30 °C (64~86 °F)

Press the ON/OFF button.

The unit will respond with beep sound.

Press MODE button to select Cooling Mode.

Press the JET COOL button. The unit will operate in super

high fan speed in cooling mode.

h Wall mounted models operate power cooling mode for

30 minutes.

To cancel the Power cooling Mode press the Jet Cool button or the fan button

or the room temperature setting button again and the unit will operate in high

fan speed in cooling mode.

or or

Cooling Mode - Power Cooling

Cooling Mode - Standard Operation

Owner's Instruction

10 Ceiling Cassette-Type Air Conditioner

Owner's Instruction

This Function is only available on some products.

Auto Operation Mode

Press the ON/OFF button.

The unit will respond with beep sound.

Press MODE button to select Auto Operation Mode.

During Auto Operation Mode

• If the system is not operating as desired, manually switch to another mode. The system will not

automatically switch from the cooling mode to the heating mode, or from heating to cooling, then you must

set the mode and the desired temperature again.

Set the desired temperature.

The temperature and fan speed are automatically set by the

electronic controls based on the actual room temperature.

If you feel hot or cold, press TEMPERATURE SETTING buttons for

more cooling or heating effect.

You cannot switch the indoor fan speed. It has already been set by

the Auto Operation Mode rule.

You can set desired temperature and indoor

fan speed.

Setting Temp. Range : 18~30 °C (64~86 °F)

Code Feel

2 Cold

1 Slightly cool

0 Neutral

-1 Slightly warm

-2 Warm

❈ Please select the code

depend on your feeling.

To lower the temperature

To raise the temperature

Owner's Manual 11

ENGLISH

Owner's Instruction

Auto Changeover Mode

Press the ON/OFF button.

The unit will respond with beep sound.

Press MODE button to select Auto Changeover Mode.

Set the desired room temperature.

You can select the fan speed in four steps low, medium, high and

chaos. Each time the button is pressed, the fan speed mode is

shifted.

To lower the temperature

To raise the temperature

h Setting Temp. Range in Auto

Changeover Mode : 18~30 °C

(64~86 °F)

• During Auto changeover Mode

- The air conditioner changes the operation mode automatically to keep indoor temperature.

When room temperature vary over ±2 °C(4 °F) with respect to setting temperature, air conditioner keeps the

room temperature within ±2 °C(4 °F) with respect to setting temperature by auto changeover mode.

• This function may not be supported, depending on the model.

12 Ceiling Cassette-Type Air Conditioner

Owner's Instruction

Auto Changeover Mode - Setting the Mode Change Temperature

This Function is to set the operating mode of the Auto Changeover Mode.

In Auto Changeover Mode, Press FUNCTION button to select Setting the Mode Change

Temperature.

Press the TEMPERATURE SETTING button to set desired Mode Change Temperature.

(Default value is 2 °C(4 °F).)

To lower the temperature

To raise the temperature

h Mode Change Temp. Range : 1~7 °C(2~14 °F)

• The Mode Change Temperature is the difference of temperature when from cooling mode to heating mode or

from heating mode to cooling mode.

- When setting temperature is 25 °C(76 °F) and room temperature is 20 °C(68 °F), then operating mode is

heating. If you set the mode change temperature to 2 °C(4 °F), when the room temperature up to

27 °C(25 °C + 2 °C)(80 °F(76 °F + 4 °F)), the unit start cooling operation.

• This function may not be supported, depending on the model.

Owner's Manual 13

ENGLISH

Owner's Instruction

Dehumidification Mode

Press the ON/OFF button.

The unit will respond with beep sound.

Press MODE button to select Dehumidification Mode.

Set the fan speed. You can select the fan speed in four steps - low,

medium, high, or chaos. Each time the button is pressed, the fan

speed mode is shifted.

During Dehumidification Mode

• If you select the dehumidification mode on the operation selection button, the indoor unit starts to run the

dehumidification function, automatically setting the room temp. and air volume to the best condition for

dehumidification based on the sensed room temp.

In this case, the setting temp. is not displayed in the Remote Controller and you are not able to control the

room temp. either.

• During the healthy dehumidification function, the air volume is automatically set according to the algorithm

responding to the current room temp. and makes the room condition healthy and comfortable even in the

high humidity season.

14 Ceiling Cassette-Type Air Conditioner

Owner's Instruction

Set the desired temperature by pressing TEMP button.

Press ROOM TEMPERATURE CHECKING button to check the room

temperature.

When setting the desired temperature is lower than room

temperature, heating wind isn’t blow out.

Set the fan speed again. You can select the fan speed in four steps–

low, medium, high, or chaos. Each time the button is pressed, the fan

speed mode is shifted.

Press the ON/OFF button.

The unit will respond with beep sound.

Press MODE button to select Heating Mode.

Heating Mode

This Function is only for H/P model.

To lower the temperature

To raise the temperature

h Setting Temp. Range in

Heating Mode : 16~30 °C

(60~86 °F)

Owner's Manual 15

ENGLISH

Owner's Instruction

Fan Mode

Set the fan speed again. You can select the fan speed in four steps–

low, medium, high, or chaos. Each time the button is pressed, the fan

speed mode is shifted.

Press the ON/OFF button.

The unit will respond with beep sound.

Press MODE button to select Fan Mode.

Natural Wind by the chaos Logic

• For more fresh feeling than other fan speed, press the Indoor Fan Speed Selector and set to chaos mode. In

this mode, the wind blows like natural breeze by automatically changing fan speed according to the chaos

logic.

During Fan Mode

• The outdoor compressor doesn't work.

Have a function to circulate the indoor as it sends out the air that doesn't have much temperature difference

with indoor.

16 Ceiling Cassette-Type Air Conditioner

Temperature Setting/Room Temperature checking

We can simply adjust the desired temperature

• Press the buttons to adjust the desired temperature

: Increase Temp. per one time pressing

: Decrease Temp. per one time pressing

Room temp: Indicate the current room temperature

Set temp: Indicate the temperature that user want to set

The cooling mode doesn't work if desired temperature is higher than

room temperature Please lower the desired temperature

The heating mode doesn't work if desired temperature is lower than room

temperature Please increase the desired temperature

Whenever press ROOM TEMPERATURE button, the room temperature

will be displayed within 5 seconds.

After 5 seconds, it turns to display the desired temperature.

Because of location of remote controller, the real room temperature and

the this displayed value can be different.

Press ROOM TEMPERATURE button for 5 seconds, temperature unit

change Celsius to Fahrenheit or Fahrenheit to Celsius.

Temperature Setting/Room Temperature checking

Owner's Manual 17

ENGLISH

Airflow Setting

The up/down airflow (Vertical Airflow) can be adjusted by using the remote controller.

1. Press the ON/OFF button to start the unit.

2. Press UP/DOWN AIRFLOW button and the louvers will swing up and down.

Press the UP/DOWN AIRFLOW button again to set the vertical louver at the desired airflow direction.

• If you press the UP/DOWN AIRFLOW button, the horizontal airflow direction is changed automatically based

on the Auto Swing algorithm to distribute the air in the room evenly and at the same time to make the human

body feel more comfortable, as if enjoying a natural breeze.

• Always use the remote controller to adjust the up/down airflow direction. Manually moving the vertical airflow

direction louver by hand, could damage the air conditioner.

• When the unit is shut off, the up/down airflow direction louver will close the air outlet vent of the system.

The left/right(horizontal) airflow can be adjusted by using the remote control.

1. Press the ON/OFF button to start the unit.

2. Press the LEFT/RIGHT AIRFLOW button and the louvers will swing left and right. Press the

Horizontal Airflow Direction Control Button again to set the horizontal louver at the desired

airflow direction.

h Up/Down and Left/Right Airflow function isn’t shown on display of remote controller.

Left/Right Airflow Direction Control (Optional)

Up/Down Airflow Direction Control (Optional)

Airflow Setting

• This function may not be supported, depending on the model.

• The feature can be changed according a type of model.

18 Ceiling Cassette-Type Air Conditioner

Sub function

Press the ON/OFF button.

The unit will respond with beep sound.

Press the PLASMA button. Plasma Purification will

start when the button is pressed and stop when the

button is pressed again.

PLASMA Purification only

If you press the PLASMA button, Plasma Purification operates.

• Plasma filter is a technology developed by LG to get rid of

microscopic contaminants in the intake air generating a

plasma of high charge electrons. This plasma kills and

destroys the contaminants completely to provide clean and

hygienic air.

• This function can be used in any operation mode and any fan

speed can be used while plasma filter is functioning.

Auto Clean (Optional)

This function operate when the unit is turned off.

Press the FUNCTION SETTING button 1 time.

Auto Clean symbol will blink.

Press the SET/CLEAR button to reserve or cancel the Auto Clean function.

If the Auto Clean function is reserved, whenever the unit is turned off, the indoor fan is

still running for about 30 minutes internally without cooling or dehumidification operation.

Also the louver is closed.

This dries up any remains of moisture & cleans the unit internally.

Plasma Purification(Optional)

Sub function

Owner's Manual 19

ENGLISH

Sub function

Smart Clean (Optional)

The Smart Clean function can be used by setting to manual or automatic.

Auto Smart Clean operation

If the accumulated operation time of the product exceeds 30 hours, the Smart Clean automatically starts

when the unit is turned off.

1. Press the FUNCTION SETTING button 2 times.

Smart Clean symbol will blink.

2. Press the SET/CLEAR button to reserve or cancel the Smart

Clean function.

You can set/clear with out on or off.

1. When the unit stop, press the FUNCTION button to select Smart Clean.

Smart Clean symbol blinks, then press SET/CLEAR button.

2. To stop Manual Smart Clean operation, press the FUNCTION button to select

Smart clean and press SET/CLEAR button.

Manual Smart Clean operation

The brush clean a dust from the filter by moving from left to right or from right to left on the filter.

The sucked dust is collected into the dust box.

The operating process of Smart Clean is different from the product type.

20 Ceiling Cassette-Type Air Conditioner

Sub function

Electric heater (Optional)

It can only be set during heating operation.

Press the FUNCTION SETTING button 3 times.

Electric heater symbol will blink.

Press the SET/CLEAR button to reserve or cancel the Electric heater function.

• The indoor unit displays during the heating mode, the Auxiliary heater is automatically turned on, but it is not

displayed on the wireless remote controller separately.

• It operates in Floor heating mode in Console products.

Press the LCD LUMINOSITY button.

It is comfortable when you feel that the display of the unit too bright .

Press the °C / °F SWITCH button to change from Celsius to Fahrenheit or from Fahrenheit to Celsius.

Whenever press TEMPERATURE SETTING button in Fahrenheit mode, the temperature

will increase/drop 2 °F.

Celsius/Fahrenheit Switching

LCD Luminosity Control (Optional)

Page is loading ...

LG AMNW24GTPA0 User manual

Brand: LG

Model: AMNW24GTPA0

Category: Split-system air conditioners

Type: User manual

Download PDF

report

LG AMNW24GTPA0 User manual

LG AMNW24GTPA0 User manual

Other documents