Dacor HRTP486SNG Installation guide

Brand: Dacor

Model: HRTP486SNG

Category: Cookers

Type: Installation guide

This manual is also suitable for

HRTP366SNGH

Dacor HRTP486SNG is a rangetop with advanced features designed to make cooking easier and more enjoyable. Its 48-inch width provides ample space for multiple pots and pans, while the high-powered burners deliver precise temperature control for consistent results. The rangetop also features a built-in griddle, perfect for cooking pancakes, eggs, and other breakfast favorites.

Installation Instructions

Heritage Rangetop

HRTP366, HRTP486

Part No. 113928 Rev. B

THIS APPLIANCE HAS BEEN TESTED IN ACCORDANCE WITH THE LATEST

EDITION OF ANSI Z21.1 STANDARD FOR HOUSEHOLD GAS APPLIANCES.

Installation Instructions .................................................... 8

Rangetop Installation ....................................................... 8

Gas Line Connection ....................................................... 9

Burner Component Installation ...................................... 10

Burner Knob Installation ..................................................11

Verifying Proper Operation ............................................. 12

Installation Checklist ...................................................... 13

Wiring Diagram ................................................................ 14

Notes................................................................................. 15

Table of Contents

Before You Begin...

Important Safety Instructions .......................................... 1

Important Information About Safety Instructions .............. 1

General Safety Precautions ............................................. 2

Installation Requirements ................................................ 3

Electrical Requirements ................................................... 3

Gas Supply Requirements ............................................... 3

Product Dimensions ......................................................... 3

Cabinet and Countertop Layout ....................................... 4

Cabinet/Cutout Dimensions ............................................. 5

All specifications are subject to change without notice. Dacor

assumes no liability for changes to specifications.

Important:

• Installer: In the interest of safety and to minimize problems, read these installation instructions completely and care-

fully before you begin the installation process. Leave these installation instructions with the appliance.

• Customer: Keep these installation instructions for future reference and the local building inspector’s use.

CALIFORNIA PROPOSITION 65 WARNING

The burning of gas cooking fuel generates some by-products that are on the list of substances which are known by

the State of California to cause cancer or reproductive harm. California law requires businesses to warn customers of

potential exposure to such substances. To minimize exposure to these substances, always operate this unit according

to the use and care manual, ensuring you provide good ventilation when cooking with gas.

If You Need Help...

If you have installation issues or repair/operation/warranty

questions, contact Dacor Customer Assurance. Before call-

ing, have available the rangetop model and serial numbers,

which are on the data label on the chassis bottom.

Dacor Customer Assurance

Phone: 833-35-ELITE (833-353-5483 USA, Canada

Mon – Fri 5:00

a.m. to 5:00 p.m. Pacific Time

Website: www.dacor.com/customer-care/contact-us

Customer Service Information

Product Data Label

• The product data label contains the model and serial

number information and the electrical and gas supply

requirements.

• It is attached to the bottom of the chassis.

Model Identification

HRTP366S/NG/H

SIZE (in inches)

GAS TYPE

NG = Natural Gas

LP = Liquid Petroleum

(Propane)

ALTITUDE

H = High Altitude Model, 4000 ft.(1219 m) and up

No character = Equipped for low altitude operation

Important Information About

Safety Instructions

• The Important Safety Instructions and warnings in

this manual are not meant to cover all possible prob-

lems and conditions that can occur. Use common

sense and caution when installing, maintaining or oper-

ating this or any other appliance.

• Always contact Dacor Customer Assurance with issues

and conditions you cannot resolve. See If You Need

Help... (previous page).

Important Safety Instructions

Safety Symbols and Labels

DANGER

Immediate hazards that WILL result in severe personal

injury or death.

WARNING

Hazards or unsafe practices that COULD result in severe

personal injury or death.

CAUTION

Hazards or unsafe practices that COULD result in minor

personal injury or property damage.

WARNING

TO REDUCE THE RISK OF INJURY TO PERSONS IN

THE EVENT OF A RANGE TOP GREASE FIRE:

a. SMOTHER FLAMES with a close-fitting lid, cookie

sheet or metal tray, then turn off the burner. BE

CAREFUL TO PREVENT BURNS. If the flames do

not go out immediately, EVACUATE AND CALL THE

FIRE DEPARTMENT.

b. NEVER PICK UP A FLAMING PAN - you may be

burned.

c. DO NOT USE WATER, including wet dish cloths or

towels - a violent steam explosion may result.

d. Use a fire extinguisher ONLY if:

◊ You have a Class ABC extinguisher, and you

already know how to operate it.

◊ The fire is small and contained in the area where

it started.

◊ The fire department is being called.

◊ You can fight the fire with your back to an exit.

WARNING

If the information in this manual is not

followed exactly, a fire or explosion may

result causing property damage, personal

injury or death.

- Do not store or use gasoline or other

flammable vapors and liquids in the

vicinity of this or any other appliance.

- WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not use any phone in your build-

ing.

• Immediately call your gas supplier

from a neighbor’s phone. Follow the

gas supplier’s instructions.

• If you cannot reach your gas supplier,

call the fire department.

- Installation and service must be per-

formed by a qualified installer, service

agency or the gas supplier.

WARNING

WARNING – NEVER use this appliance as a space

heater to heat or warm the room. Doing so may result

in carbon monoxide poisoning and overheating of the

appliance.

WARNING

WARNING – NEVER cover any slots, holes or passages

on the rangetop or rangetop chassis. Doing so blocks

air flow through the rangetop and may cause carbon

monoxide poisoning. Aluminum foil linings may also trap

heat, causing a fire hazard. Keep all slots, holes and

passages clear of grease and grime.

READ AND SAVE THESE INSTRUCTIONS

Important Safety Instructions

• Read the accompanying use and care manual com-

pletely before operating this appliance.

• Keep packaging materials away from children.

Plastic sheets and bags can cause suffocation.

• If you receive a

damaged product, immediately con-

tact your dealer or builder. Do not install or use a

damaged appliance.

• This rangetop must be properly installed and ground-

ed by a qualified installer according to these instal-

lation instructions prior to use. The installer should

show the customer the location of the gas shut off

valve and the electrical outlet so that they know

where and how to turn off the gas supply and dis-

connect power to the rangetop. Proper installation is

the responsibility of the customer.

• This appliance is not designed for installation in a

mobile home or recreational vehicle.

• Installations with less than 2 1/2” (6.4 cm) from the

rear of the rangetop to a combustible material must

use a non-combustible material. See the latest

version of ANSI Z223.1.

• Do not use this appliance in combination with a

surface (countertop) ventilation system, air curtain or

other type of range hood that directs airflow in a

downward direction.

• Do not install, repair or replace any part of the ran-

getop unless specifically recommended in the litera-

ture accompanying it. A qualified service technician

should perform all other service. Do not tamper with

the controls. Do not operate the rangetop without the

knobs and trim rings in place.

• Before cleaning, servicing or installing this rangetop,

make sure that the gas supply is turned off at the gas

supply valve and that the power plug is discon-

nected from the electrical outlet.

• Do not connect this rangetop to the gas supply with-

out the supplied gas pressure regulator installed.

• Clean this appliance only in the manner specified in

the use and care manual.

• Only use the rangetop for cooking tasks expected of

a home appliance as outlined in the literature accom-

panying it. This rangetop is not intended for commer-

cial or laboratory use.

WARNING

General Safety Precautions

To reduce the risk of fire, electric shock, serious injury or death when using your appliance, follow basic safety precau-

tions, including the following:

• DO NOT TOUCH THE SURFACES OF THE

Rangetop OR THE SURROUNDING AREAS DURING

OR IMMEDIATELY AFTER USE

• Do not climb on any part of the appliance.

• To avoid a fire hazard, do not hang flammable or

heat sensitive objects over the rangetop.

• Do not leave children alone or unattended in the

area around the rangetop. Do not allow children

to play with the controls or touch other parts of the

rangetop. Do not store items of interest to children

on top of or above the rangetop. Children could be

burned or injured while climbing on the appliance.

• Clean the rangetop thoroughly before operating it for

the first time. Make sure that all the rangetop parts

are dry before lighting a burner.

• Keep flammable items, such as paper, cardboard,

plastic and cloth away from the burners and other

hot surfaces. Do not place such items on the ran-

getop. Do not allow pot holders to touch hot surfaces

or gas burners.

• Do not wear loose or hanging apparel while using

the rangetop. Do not allow clothing to come into con-

tact with the rangetop and surrounding areas during

and immediately after use. Do not use towels or

bulky cloth as pot holders.

• If the rangetop is near a window, do not use long

curtains as window treatment. The curtains could

blow over the rangetop and create a fire hazard.

IMPORTANT - This appliance is equipped with a

three prong grounding plug for your protection against

possible electric shock hazards.

Plug it only into a dedicated,

grounded three prong electrical

outlet. It is the responsibility

of the customer to make sure

the proper type of outlet is

installed. Do not under any

circumstances:

• Cut or remove the third (ground) prong from the

power cord.

• Use an adapter plug.

• Use an extension cord.

• Use a power cord that is frayed or damaged.

• Connect to an electrical outlet with a ground fault

interrupter (GFI).

WARNING

Product Dimensions

WIDTH (A)

HRTP366 35 7/8” (91.1 cm)

HRTP486 47 7/8” (121.6 cm)

Installation Requirements

WARNING

• The installation of this appliance must conform with

local codes or, in the absence of local codes, with the

National Fuel Gas Code, ANSI Z223.1/NFPA 54.

• To prevent an electric shock hazard, the power sup-

ply must meet the specifications stated below.

The electrical and gas supply data on this page is for refer-

ence only. If the requirements below do not agree with the

product data label, use the data on the product data label.

Electrical Requirements

• The appliance installation must be electrically grounded

in accordance with local codes or, in the absence of

local codes, with the National Electrical Code, ANSI/

NFPA 70.

• The correct voltage, frequency and amperage must be

supplied to the electrical outlet according to the product

data label located on the bottom of the chassis.

• The electrical outlet must be installed by a licensed

electrician in an accessible location so that the power

cord may easily be disconnected during cleaning and

service.

ELECTRIC CIRCUIT REQUIREMENTS

Circuit Required Total Connected Load

120 Vac 60 Hz,

15 Amp. (3 wire)

0.25 Amp @ 120 Vac, 60 Hz

Gas Supply Requirements

• Check your local building codes for the proper method

of installation. In the absence of local codes, this

appliance should be installed in accordance with the

National Fuel Gas Code ANSI Z223.1/NFPA 54. The

gas service must be installed by a qualified profes-

sional.

• Be certain that the rangetop being installed is cor-

rect for the gas service being provided (natural gas or

LP gas). Also, if operating the rangetop at an altitude

above 4000 ft. (1219 m) make sure it is equipped for

high altitude operation. See the inside cover for more

information.

• An external manual shut-off valve must be installed

between the gas inlet and the rangetop for the purpose

of turning on or shutting off gas to the appliance.

• The factory provided regulator shipped with the appli-

ance must be installed in the gas line that runs from the

gas shut off valve to the rangetop gas inlet. Use only

the regulator provided. The regulator inlet accommo-

dates a 3/4” gas supply line and is also compatible with

a 1/2” house gas supply. The inlet to the rangetop itself

is equipped with a 3/4” male NPT fitting.

GAS SUPPLY PRESSURE REQUIREMENTS*

Gas Type

Manifold

Pressure

Minimum Gas

Supply Pressure

Natural Gas 5” Water Column 6” Water Column

Propane (LP)

10” Water

Column

11” Water Column

* Maximum gas supply pressure for all models is 1/2 psi

3 3/8”

(8.6 cm)

7/16”

(1.1 cm)

7 3/4”

(19.7 cm)

Trim:

1/4”

(6.4 mm)

thick

25 3/8” (64.5 cm)

1 1/4” (3.2 cm) cooking surface

height (grate level) above

countertop

3/4” NPT gas inlet, connects to regulator

from bottom or rear of unit, end is recessed

2” (5.1 cm) from chassis bottom

26 5/16” (66.8 cm)

27 5/16” (69.4 cm)

Power cord

40” long

Product tolerances: ±1/16” (±1.6 mm) unless otherwise

noted.

SIDE VIEW

Cabinet and Countertop Layout

WARNING

To avoid the risk of fire or personal injury, all minimum

and maximum specified clearances on this and the

following pages must be maintained or exceeded.

General Considerations

• The minimum distance from the back of the rangetop

to a combustible rear wall is 2 1/2” (6.4 cm) minimum

(Figure 1).

• Installation of a non-combustible material (up to the

hood) or

a backsplash is always recommended, and

mandatory if the distance to the back wall from the

ran-getop is less than 2 1/2” (Figure 2). Consult local

codes and ordinances for acceptable non-combustible

materials.

• Carefully check the location where the rangetop is

to be installed. For best performance, the rangetop

should be installed away from drafts caused by doors,

windows and heating and air conditioning outlets. To

reduce the risk of personal injury from reaching over a

hot appliance, avoid cabinet installations directly above.

• All contact surfaces between the rangetop and the

counter must be solid and level.

Installation Requirements

• To reduce the risk of personal injury and to reduce

accumulated smoke in the room, Dacor strongly rec-

ommends installing a range hood or downdraft vent. A

hood should project horizontally a minimum of five (5)

inches beyond the face of the cabinets.

• The installation must allow access to the underside

of the rangetop for service and inspection purposes,

including the ability to turn off the rangetop gas supply

valve and electrical outlet.

• The countertop overhang on the sides of the cutout

shown on the following pages covers the recessed por-

tions of the rangetop behind the control panel and cre-

ates a seamless look for the installation.

• IMPORTANT: When installing the rangetop into a lami-

nated or synthetic countertop, radius the corners of the

cutout to help avoid cracking. Consult the countertop

manufacturer’s instructions for minimum corner radius,

reinforcement and heat protection requirements.

• For installations with a downdraft vent, install this appli-

ance only with the approved Dacor downdraft vent

models listed on page 6.

Gas and Electric Service Location

• A manual gas shut-off valve must be installed in an

accessible location in the gas line external to the appli-

ance for the purpose of turning on or shutting off gas to

the appliance.

• The gas supply piping, gas shut-off valve and the elec-

trical outlet must be located so they do not interfere

with the rangetop when it is installed. If installing anoth-

er appliance in the cabinet below, allow for the routing

of gas and electrical service out the back of the unit.

• The shaded area on the facing page shows the rec-

ommended location of the gas inlet and the electrical

outlet. For replacement purposes, the location of the

existing utilities may be utilized provided they do not

interfere with the sides or rear of the rangetop. Check

local building codes for permissible utility locations.

• For best performance and to minimize gas pressure

loss, attach the gas supply regulator as close as pos-

sible to the rangetop gas inlet.

The installation must:

• Allow for access to the gas shut-off valve and regulator

when the unit is installed.

• Allow for access to the electrical outlet, when the ran-

getop is in place so that the power cord may be easily

disconnected if the unit needs service.

• Allow for connection of the (40”) power cord to the

electrical outlet.

• If a downdraft vent is to be installed, allow for access

to the gas supply valve and electrical outlet when the

downdraft vent is in place.

Non-combustible material or

backsplash mandatory if gap

from back of cooktop to

combustible wall is less than

2 1/2”

Combustible

rear wall

2 1/2” (6.4 cm) min. to

combustible rear wall

FIGURE 1

FIGURE 2

Combustible

rear wall

Recommended

gas and electrical

service location,

consult local code

10” (25.4 cm) to

combustible side

wall min. both sides

1/2” (1.3 cm)

overhang,

both sides

1 1/2” (3.8 cm)

typical countertop

thickness

7 3/4”

(19.7 cm)

36” (91.4 cm)

typical

Mounting platform

1” (2.5 cm) min.

thickness

Installation Requirements

Cabinet/Cutout Dimensions

Cabinet/Countertop Dimensions - Front View

Cabinet/Countertop Dimensions -

ISO View

Cabinet tolerances ±1/16” (±1.6 mm) unless otherwise noted.

continued on following

pages...

See note 2

See Cabinet/Countertop Dimensions - Top View

This specification not applicable for cabinets more

than a horizontal distance of 10” (25.4 cm) from the

edge of the rangetop.

Vertical to combustible surface from rangetop grate level;

if installing an overhead vent hood, also check the hood

specifications for minimum required clearances.

13” (33.0 cm)

max.

Top of

finished

counter

Grate

level

Grate

level

15” (40.6 cm)

min.

1, 3

30” (76.2 cm)

min.

Cutout for

utility access

Rangetop

Model

B C

HRTP366 36” (91.4 cm)

36” (91.4 cm)*

42” (106.7 cm)**

HRTP486 48” (121.9 cm)

48” (121.9 cm)*

54” (137.2 cm)**

* Minimum ** Recommended

Cabinet/Countertop Dimensions (cont.)

Installation Requirements

Non-combustible

rear wall, rear of

mounting platform

10” (25.4 cm) min.

to combustible wall

above countertop,

both sides

Cabinet face

below countertop

overhang

Increase countertop and overhang

additional 2 1/2” (6.4 cm) min. for

combustible rear wall above

countertop

3/8” (1.3 cm)

countertop overhang

Hole 1/2” dia. (1.3 cm),

2 places, through platform

for hold down bolts

Gas/electrical utility cut-out in right rear corner of

mounting platform 8” W X 6” D (20.3 cm X 15.2 cm),

if gas and electrical are routed through bottom

1/2” (1.3 cm)

countertop

overhang

1” (2.5 cm) thick mounting platform min.

Countertop

1/2” (1.3 cm)

countertop

overhang

2” (5.1 cm)

Counterop

overhang

1” (2.5 cm)

typical

1 3/8”

(3.5 cm)

max.

11 7/16”

(29.1 cm)

24”

(63.5 cm)

min.

cabinet

depth

D D

Rangetop

Model

B - Cutout

Width

D - Hole

Offset

E - Downdraft

Vent Cutout

Approved Downdraft

Vent Models

HRTP366

36”

(91.4 cm)

16 5/8”

(42.2 cm)

33 1/2”

(85.1 cm)

MRV3615S

HRTP486

48”

(121.9 cm)

20 13/16”

(52.9 cm)

43 1/2”

(110.5 cm)

MRV48S

Cabinet/Countertop Cutout Dimensions without Downdraft Vent - Top View

Installed Rangetop - Side View

Gas connection and power cord may be

routed through bottom or back of chassis

Gas and electrical connections at

right rear section of chassis

Cabinet

face

Installed control

panel overhang

1/3/8” (3.5 cm)

24” (61.0 cm)

Countertop

Mounting platform

IMPORTANT: Use only the downdraft vent models specified.

Cabinet tolerances ±1/16” (±1.6 mm) unless otherwise noted.

Installation Requirements

NOTE: Gas and electrical connections may only be routed through

the bottom of the rangetop when installed with a downdraft vent.

Non combustible rear

wall recommended

10” (2.5 cm) min. to

combustible wall

above countertop,

both sides

Cabinet face

below countertop

overhang

3/8” (1.0 cm) min.

countertop overhang

2 5/8”

(6.7 cm)

Hole 1/2” dia. (1.3 cm),

2 places, through platform

for hold down bolts

1/2” (1.3 cm)

countertop

overhang

1” (2.5 cm) thick mounting platform min.

Open to below to allow for raised

vent, gas and electrical connections

Countertop

1/2” (1.3 cm)

countertop

overhang

2” (5.1 cm)

11 7/16”

(29.1 cm)

26 5/8”

(67.6 cm)

min.

cabinet

depth

Counterop

overhang

1” (2.5 cm)

typical

1 3/8”

(3.5 cm)

max.

15”

(38.1 cm)

Cabinet/Countertop Cutout Dimensions with Downdraft vent - Top View

Cabinet/Countertop with Downdraft vent - Side View

Stiffener

Cabinet face

Control panel

overhang

1 3/8” (3.5 cm)

Countertop

Dacor approved

downdraft vent

IMPORTANT: See downdraft

installation instructions for

duct system layout/planning

DYRTP366 or

DYRTP486 rangetop

3/8” min. (1.0 cm)

space behind

downdraft vent

chassis to clear

stiffener

3/8” min. (1.0 cm)

flat countertop overhang

required behind cutout

Minimum

countertop

height:

30 1/4"

(76.8 cm)

HRTP366, HRTP486

Installation Instructions

Unpack the Rangetop

WARNING

• If the gas and electric service provided does not

meet the product specifications, do not proceed with

the installation. Call the dealer, the gas supplier or a

licensed electrician.

• The rangetop is heavy. A minimum of two people are

required to safely install it.

Unpack the parts box and verify that all required compo-

nents have been provided. If any item is missing or dam-

aged, please contact your dealer immediately. Do not install

a damaged or incomplete appliance. The customer must

report cosmetic issues within 30 days of installation.

• 3 Grates

• 8 standard burner caps (4 brass, 4 porcelain)*

• 4 standard burner rings

• 4 SimmerSear™ burner caps (2 brass, 2 porcelain)*

• 2 SimmerSear burner rings

• 2 SimmerSear burner heads

• 4 standard knobs

• 2 MAX GRIDDLE knobs

• Dacor Stainless Steel Cleaner

• WOK ring

• Griddle

• 2 hold down bolts

• 2 washers (for hold down bolts)

• Gas regulator

• Product literature

*The rangetop is supplied with two different types of burner

caps (brass and porcelain) to suit the customer’s prefer-

ence.

Rangetop Installation

WARNING

• To prevent damage to the gas pressure regulator,

install it only after the rangetop is mounted in its per-

manent position.

• Do not over-tighten the hold down bolts. Over tight-

ening the hold down bolts may result in improper

burner operation.

IMPORTANT

Do not use a hardening compound or caulk to

permanently seal the rangetop into place. The rangetop

must be readily removable if service is required. Removal

of sealant to service the unit will be performed at the

customer’s expense.

1. Lower the rangetop into the cutout while feeding the

electrical cord into the utility cutout. Center the ran-

getop in the cutout.

2. Secure the rangetop to the countertop using the two

(2) provided hold-down bolts and washers provided. Do

not overtighten the bolts.

Installation Instructions

Gas Line Connection

WARNING

• Verify that the gas supply meets specifications before connection. See page 3.

• The maximum gas supply pressure to the regulator must never exceed 1/2 pounds per square inch (psi) or 3.5 kPa.

• Do not install or use the rangetop without the included gas regulator installed.

• Ensure that the arrow on the regulator points in the direction of the gas flow, towards the rangetop.

• Do not apply excessive pressure when tightening gas connections and fittings.

• Do not use Teflon tape or plumber’s putty on flexible gas line connections.

• Test the gas lines for leaks as instructed before use. Do not use a flame to check for leaks.

• The gas supply pressure for testing the regulator setting shall be at least 1 inch water column (249 Pa) above the

specified manifold pressure. See page 3.

• The rangetop and shut-off valve must be disconnected from the gas supply piping system during any pressure test-

ing exceeding 1/2 psi (3.5 kPa).

• The rangetop must be isolated from the gas supply piping system by closing the shut-off valve to the rangetop dur-

ing any gas supply piping system pressure testing equal to or less than 1/2 psi (3.5 kPa).

• For LP gas installations, the LP gas tank must have its own high-pressure regulator in addition to the pressure regu-

lator supplied with the rangetop.

IMPORTANT

Within the Commonwealth of Massachusetts, this appliance must be installed by a licensed plumber or gas fitter.

1. Attach the gas pressure regulator (included with the

rangetop) to the 3/4” (1.9 cm) male NPT gas inlet on

the rangetop. The inlet is located on the bottom, at the

right rear portion of the chassis. For tight installations,

the regulator may be installed upstream from the pipe

nipple, anywhere between the shut-off valve and the

rangetop. For best performance, minimize gas pressure

loss by attaching the regulator as close as possible to

the rangetop gas inlet.

2. Complete connection of the gas supply to the ran-

getop by installing a minimum 1/2” flexible gas line (not

included) between the pressure regulator and the shut-

off valve.

3. Check for gas leaks:

◊ Turn all rangetop control valves to the OFF posi-

tion.

◊ Turn on the gas supply valve and check all lines

and connections for leaks using a soap and water

solution or a gas leak detector.

◊ Turn the gas supply valve off.

Installation Instructions

SimmerSear Burner Assembly Standard Burner Assembly

Spill tray

Standard

burner

SimmerSear

burner

Burner cap

Burner ring

Burner head

Burner base

Keyed hole

Ridge on bottom

of burner cap

Ridge on bottom

of burner cap

Burner Component Installation

WARNING

• Never attempt to operate the rangetop with any of the

burner parts removed.

• Do not attempt to adjust the burner air mixture set-

tings. All adjustments are preset at the factory.

• Remove the burner parts and grates from their shipping

packages.

• Install the burners as shown. Either type (color) of the

supplied burner caps may be used. When installing the

burner components, twist each piece back and forth

slightly until it drops completely into place. The burners

will not operate properly unless all of the burner pieces

are properly seated.

• Gently set the grates on top of the spill tray. Make sure

that the rubber feet are positioned in the dimples.

STEP 1: Install

burner head.

Put locating

tap into keyed

hole.

STEP 1: Put

burner ring on

top of the head.

STEP 3: Install

burner cap.

Ridge on cap

must surround

top of ring.

STEP 3: Install

burner cap. Ridge

on cap must sur-

round top of ring.

STEP 2: Install

burner ring. Line

up ring tabs

with head slots.

Twist back and

forth to assure

proper seating.

STEP 2: Turn

ring until it drops

into place. Twist

back and forth

to assure proper

seating.

Installation Instructions

Burner Knob Installation

CAUTION

Installing the rangetop knobs in the wrong position may

result in damage to the rangetop griddle. The knobs for

the center burners are marked with the maximum griddle

settings.

There are two (2) different types of knobs supplied with the

rangetop. The knobs for the center burners have the words

MAX GRIDDLE on them.

• If not already installed, put the knobs with the words

MAX GRIDDLE on them onto the inner (center burner)

valve shafts.

• Put the remaining knobs on the outer valve shafts .

• When installing the knobs, align the “D-shaped” open-

ing on the back of the knob with the end of the valve

shaft. Carefully push the knob on until it stops.

Icons on outer burner knobs

Icons on center burner knobs

Verifying Proper Operation

WARNING

• Make sure that power to the electrical outlet is turned

off at the circuit breaker or fuse box and that the gas

is turned off at the gas supply valve before proceed-

ing.

• The rangetop must be properly grounded at all times

when electrical power is applied.

Prior to operating the rangetop, read the accompanying use

and care manual carefully.

1. Make sure all the

rangetop burner con-

trols are in the OFF

position.

2. Connect the power

cord to the electrical outlet.

3. Turn on power to the electrical outlet at the circuit

breaker panel or fuse box.

4. Gently push in and turn one of the burner control knobs

counterclockwise to the HIGH position. Verify that the

associated burner igniter sparks, then return the knob

to the OFF position. Repeat for all of the remaining

burner knobs.

5. Turn on the gas supply valve.

6. Perform the following ignition test for all of the burners,

one at a time:

• Push in and turn one of the control knobs counter-

clockwise to the HIGH position. Only the igniter for

the selected burner will spark. It may take up to four

seconds for the gas to ignite, at which time the ignit-

er will stop sparking. If ignition does not occur within

four seconds, turn the knob to the OFF position, wait

for at least five minutes to allow any gas to dissipate,

then repeat the test.

• Once the burner lights, the control knob can be rotat-

ed counterclockwise from HIGH to LOW to adjust the

flame height progressively.

• When the unit is installed properly, the flame will be

steady. It will also have

a sharp, blue inner cone

that will vary in length

proportional to the

burner size. The flame

will be reduced by the

Smart Flame™ feature

under the grate fingers

to increase grate life.

NOTE: If the rangetop does not operate properly, follow

these troubleshooting steps:

• Verify that power and gas are supplied to the rangetop.

• Check to make sure that the power plug is connected

to the electrical outlet and that power is turned on at

the circuit breaker panel or fuse box.

• Check to make sure that all burner parts are properly

seated.

• If the burner continues to spark after ignition without

stopping, have a licensed electrician check the electri-

cal outlet for proper grounding or reversed polarity.

• Repeat the burner ignition test.

If the appliance still does not work, contact Dacor

Distinctive Service at (800) 793-0093 ex 2822. Do not

attempt to repair the appliance yourself. Be sure to have

the model and serial numbers available when you call. See

the inside cover for location.

Dacor is not responsible for the cost of correcting problems

caused by a faulty installation.

Removing the Rangetop for

Repair

To remove the appliance for repair, perform the installation

process on the previous pages in reverse order.

Normal Flame

Appearance

Installation Instructions

OFF HIGH LOW

Installation Instructions

Installation Checklist

WARNING

• To ensure a safe and proper installation, the follow-

ing checklist should be completed by the installer to

ensure that no part of the installation has been over-

looked.

• Proper installation is the responsibility of the home-

owner. The importance of proper installation of your

Dacor rangetop cannot be overemphasized.

□ Is the electrical outlet for the rangetop grounded and

located according to these instructions and in accor-

dance with all applicable electrical codes? See pages

3 and 4.

□ Is the gas service for the rangetop located and installed

according to these instructions and in accordance with

all applicable codes? See pages 3 and 4.

□ Has the gas supply inlet pressure been measured to

ensure that it does not exceed the maximums stated in

these instructions? See page 3.

□ Is the rangetop secured using the provided hold-down

bolts and washers? See page 8.

□ Is the rangetop connected to the gas supply according

to these instructions and in accordance with all appli-

cable codes? Did the installer check the gas supply for

leaks? See page 9.

□ Are all burner parts and grates properly installed

according to these instructions? See page 10.

□ Are the knobs installed in the proper positions? See

page 11.

□ Has proper operation been verified?

□ Has the warranty been activated on-line or the warranty

card filled out completely and mailed?

Wiring Diagram

AFTER SERVICING

VERIFY PROPER OPERATION

120V, 60Hz, 0.25A

POWER SUPPLY

CAUSE IMPROPER AND DANGEROUS OPERATION.

WHEN SERVICING CONTROLS. WIRING ERRORS CAN

CAUTION: LABEL ALL WIRES PRIOR TO DISCONNECTION

WIRING DIAGRAM

DYRTP366/DYRTP486

RR LED HARNESS

RL BURNER

IGNITOR, IGNITOR,

RC BURNER

RR BURNER

IGNITOR,

FR BURNER

IGNITOR,

FL BURNER

FC BURNER

IGNITOR,

B B

BLACK

WHITE

FR LED HARNESS

FL LED HARNESS

Single Point

Spark Module

Single Point

Spark Module

Single Point

Spark Module

Single Point

Spark Module

Single Point

Spark Module

FC LED HARNESS

RL LED HARNESS

RC LED HARNESS

Single Point

Spark Module

WIRING DIAGRAM

HRTP366, HRTP486

Notes

Dacor ● 14425 Clark Avenue, City of Industry, CA 91745 ● Phone: (800) 793-0093 ● Fax: (626) 403-3130 ● www.dacor.com

Dacor HRTP486SNG Installation guide

Brand: Dacor

Model: HRTP486SNG

Category: Cookers

Type: Installation guide

This manual is also suitable for

HRTP366SNGH

Download PDF

report

Dacor HRTP486SNG Installation guide

This manual is also suitable for

Dacor HRTP486SNG Installation guide

Related papers

Other documents