Miller KG000000 Owner's manual

Miller
Brand
Miller
Model
KG000000
Type
Owner's manual

This manual is also suitable for

OWNER’S MANUAL
1996 MILLER Electric Mfg. Co.
FORM: OM-690 174 313A
November 1996
Metro Running Gear (042 941)
WARNING
FALLING EQUIPMENT can cause serious personal injury and equipment damage.
• Use lifting eye to lift unit only, NOT running gear, gas cylinders, trailer, or any other heavy options, accessories, or devices.
• Use equipment of adequate capacity to lift the unit.
rwarn1.1* 3/93
SAFETY CHAINS CAN PREVENT RUNAWAY
TRAILER in case hitch/coupler fails.
1. Always use safety chains when towing.
2. Cross safety chains under coupling to prevent tongue from
dropping to ground.
3. Allow only enough slack for tight turns.
4. Do not let safety chains drag on ground.
5. Twist safety chains equally from hook ends to take up slack.
6. Use safety chains rated equal to or greater than twice the
maximum gross trailer weight rating.
Bottom
View
Side
View
PRE-TOWING CHECKLIST
Check that the correct hitch is properly installed on towing vehicle.
When coupling, check that coupler locking device (safety pin), and safety chains are properly connected.
Check that tires are properly inflated and that wheel nuts are properly torqued.
OM-690 Page 2
ST-801 281-A / 801 081-B
Description (Qty)
Part
No.
Item
No.
1 158 266 Fender, w/bracket (2)
2 174 566 Wheel, w/tire (2)
3 174 569 Jack, 750 lb w/wheel (1)
4 601 966 Screw, .375-16 x 1.25 (3)
5 157 245 Washer, cone (22)
6 010 909 Nut, .375-16 (4)
7 130 226 Safety Chain, (2)
8 088 058 Nut, .500-13
9 602 246 Washer, flat (4)
10 601 978 Screw, .500-13 x 3.50 (2)
11 087 952 Lunette Eye (1)
12 149 638 Screw, .500-13 x 4.500 (2)
13 087 949 Bar, hitch clevis (2)
14 087 639 Coupler, hitch 2 in (1)
15 150 393 Pin, lynch .312dia (1)
16 157 390 Screw, .375-16 x 3.50 (1)
17 158 274 Towbar (1)
18 167 632 Screw, .375-16 x 1.50 (14)
19 174 570 Axle (1)
20 176 862 · Hub Assembly (2)
21 133 812 · Washer, flat (2)
22 088 866 · Nut, 1.250 (2)
23 088 879 · Nut, wheel .500-20 (10)
24 167 786 · Kit, bearing (2)
25 · · Grease Cap (1)
26 · · Pin, cotter (1)
27 · · Bearing (2)
28 · · Cup (2)
29 · · Oil Seal (1)
Be sure to provide Model when ordering re-
placement parts.
9/16, 13/16 in
1
4
2
5
3
Torque Lug Nuts
To 70 ft-lbs (95 N·m)
Torquing Sequence
Tools Needed:
1
2
3
4
5
5
6
5
7
8
9
10
9
11
12
9
13
9
8
9
8
14
15
9
10
*
16
1718
20
21
22
23
19
Includes
Items
24–29
*Included in Item 3
24
25
26
27
28
27
29
18
18
. Be sure label on axle (19) faces
rear of running gear when installed.
Optional Hitches
. Torque screws (18) to 18
- 23 ft lb (24 – 31 N·m)
5
Figure 1. Installing Running Gear
OM-690 Page 3
Ref. ST- 801 081 / Ref. ST-800 441-A
Check bearings once a year, and
repack if needed.
Torque wheel bearings whenever
hub nut is removed or hub is too
loose.
Torque nut while turning hub forward. Turn nut until “just loose.”
Install new cotter pin and bend ends around nut.
Install cap. Install wheel and recheck endplay.
Check hub endplay. If loose,
remove wheel and go to next step.
Remove cap and cotter pin.
Tools Needed:
0.01 in (0.2 mm)
endplay maximum
Further loosen nut until first slot
in nut aligns with hole in spindle.
Do not further loosen
nut more than 1/6 turn.
Pin must not
rub on cap.
13/16, 1-1/2 in
Torquing Bearings
Repacking Bearings
. Torque to 12 ft lb (16 N·m)
Figure 2. Wheel Bearing Maintenance
  • Page 1 1
  • Page 2 2
  • Page 3 3

Miller KG000000 Owner's manual

Miller
Brand
Miller
Model
KG000000
Type
Owner's manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents