Miller LH190559L Owner's manual

Type
Owner's manual

This manual is also suitable for

Miller LH190559L is a Cart Runner 300 244, designed to transport welding equipment and gas cylinders safely and conveniently. It features a sturdy construction with a weight capacity of 73 lb (33 Kg) and overall dimensions of 41-1/2 inches in length, 23-1/4 inches in width, and 45-1/4 inches in height. The cart includes a gas cylinder rack with a chain for securing the cylinder, a foot control holder, and cable holders for organizing and storing cables. It also has three side rails with screw holes for attaching accessories such as a cooling system and welding power source.

Miller LH190559L is a Cart Runner 300 244, designed to transport welding equipment and gas cylinders safely and conveniently. It features a sturdy construction with a weight capacity of 73 lb (33 Kg) and overall dimensions of 41-1/2 inches in length, 23-1/4 inches in width, and 45-1/4 inches in height. The cart includes a gas cylinder rack with a chain for securing the cylinder, a foot control holder, and cable holders for organizing and storing cables. It also has three side rails with screw holes for attaching accessories such as a cooling system and welding power source.

OWNER’S MANUAL
OM-232 455B 201004
Cart Runner 300 244
SECTION 1 CART RUNNER
1-1. Safety Symbol Definitions
DANGER! Indicates a hazardous situation which, if not
avoided, will result in death or serious injury. The possible
hazards are shown in the adjoining symbols or explained
in the text.
Cylinders contain gas under high pressure and can ex-
plode if damaged. Never let a welding electrode touch
any cylinder. Always secure cylinder to running gear,
wall, or other stationary support.
Indicates a hazardous situation which, if not avoided,
could result in death or serious injury. The possible ha-
zards are shown in the adjoining symbols or explained in
the text.
Welding processes cause flying pieces of metal and slag.
Wear safety glasses with side shields.
NOTICE
Indicates statements not related to personal injury.
Indicates special instructions.
Trailers
Falling equipment can cause serious personal injury and
equipment damage. Use lifting eye to lift unit only, not
trailer, gas cylinders, or any other accessories. Use
equipment of adequate capacity to lift unit or parts such
as engine or generator.
Running Gear
Falling equipment can cause injury and damage, over-
sized cylinder can cause tipping. Properly install and se-
cure all equipment onto cart before using cart. Always
secure or remove any tools stored on cart before moving
unit. Do not lift cart in any manner when equipment and
cylinder(s) are installed use handles to move cart. Do
not overload handles with cables use standard 10 to 15
foot cables as maximum lengths.
Beware of electric shock from welding electrode or wiring.
Touching the electrode while in contact with the work or
ground can cause electric shock. Always wear dry
gloves. Keep all panels and covers closed.
CALIFORNIA PROPOSITION 65 WARNINGS
Welding or cutting equipment produces fumes or gases which contain chemicals known to the State of California to cause birth defects
and, in some cases, cancer. (California Health & Safety Code Section 25249.5 et seq.)
This product contains chemicals, including lead, known to the state of California to cause cancer, birth defects, or other reproductive
harm. Wash hands after use.
OM-232 455 Page 2
1-2. Assembled Cart & Cylinder Rack
41-1/2
23-1/4
45-1/4
1054
591
1149
73 lb 33 Kg
Overall Dimensions
Length
Width
Height
Inches Millimeters
Weight
804 873-A
OM-232 455 Page 3
1-3. Typical Cart With Welding Power Source, Cooling System, And Gas Cylinder
5
1
2
8
804 874-A
3
6
! Be careful when placing or mov-
ing unit over uneven surfaces.
Tipping or falling equipment can
cause injury and damage equip-
ment.
1 Gas cylinder - Not Supplied
2 Chain
Obtain and install gas cylinder. Secure
gas cylinder with chain.
3 Foot Control - Not Supplied
4 Foot Control Holder
5 Cable Holders (3)
Install foot control holder and cable hold-
ers in any of the screw holes located on
top of side rails. Secure with supplied
.25020 X .50 hex head screws.
6 Cooling System - Not Supplied
7 Cart
8 Welding Power Source - Not
Supplied
7
4
Tools Needed:
3/8 in.
OM-232 455 Page 4
1-4. Cart Parts List
804 872-A
. Hardware is common and
not available unless listed.
1
2
3
4
5
6
9
10
11
12
11
13
15
14
16
17
18
7
8
Figure 1-1. Complete Assembly
Description
Part
No.
Dia.
Mkgs.
230 157
Item
No.
Figure 1-1 Complete Cart Assembly.
Quantity
1 226 927 Handle, Cart 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2 +226 929 Panel, Side Rail LH 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3 210 224 Chain, Straight Link 1/0 X 27 Bright Zinc Pld 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4 226 926 Support, Bottle 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5 192 236 Label, Caution Over Turning Can Cause Injury 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6 +226 930 Panel, Side Rail RH 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7 199 403 Holder, Foot Control 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8 191 875 Hanger, Cable/Torch 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9 226 919 Base, Cart 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10 226 920 Tray, Bottle Assy 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11 602 250 Washer, Flat .812 ID x 1.469 OD x .134t Stl Pld Ansi .750 8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12 209 869 Wheel, Polyolefin 10 In Diax 2.000 wide x .750 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
13 121 614 Ring, Rtng Ext .750 Shaft X .085 Thk E Style Pld 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
14 226 925 Support, Base Drawer Slides 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
15 226 923 Caster, Swvl 4.00 In Polyolefin 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
16 216 594 Slide, Drawer Full Extension 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
17 191 884 Drawer, 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
18 228 585 Base, Front Panel 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
To maintain the factory original performance of your equipment, use only Manufacturers Suggested
Replacement Parts. Model and serial number required when ordering parts from your local distributor.
+When ordering a component originally displaying a precautionary label, the label should also be ordered.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Miller LH190559L Owner's manual

Type
Owner's manual
This manual is also suitable for

Miller LH190559L is a Cart Runner 300 244, designed to transport welding equipment and gas cylinders safely and conveniently. It features a sturdy construction with a weight capacity of 73 lb (33 Kg) and overall dimensions of 41-1/2 inches in length, 23-1/4 inches in width, and 45-1/4 inches in height. The cart includes a gas cylinder rack with a chain for securing the cylinder, a foot control holder, and cable holders for organizing and storing cables. It also has three side rails with screw holes for attaching accessories such as a cooling system and welding power source.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI