OWNER’S MANUAL
SWISHER ACQUISITION INC.
1602 CORPORATE DRIVE, WARRENSBURG, MISSOURI 64093
P
HONE 660-747-8183 FAX 660-747-8650
ade I The
USA
of US and Global Parts
swisherinc.com
CHANGING YOUR LANDSCAPE SINCE 1945
Starting Serial #: L216-001001
20689 REV 16-001
20670
IMPORTANT
Read and follow all
Safety Precautions
and Instructions
Before Operating this
Equipment.
Connects to Tractors:
ZTR28BT
Z31KT
Compatible with Plow Blades:
2645R 50”
2850 62”
20099 50” Commercial Pro
20100 62” Commercial Pro
Commercial Pro
Plow Blade Mount Attachment
In the event you have a claim under this warranty, you must return the product to an authorized
service dealer. All transportation charges, damage, or loss incurred during transportation of parts
submitted for replacement or repair under this warranty shall be borne by the purchaser. Should you
have any questions concerning this warranty, please contact us toll-free at 1-800-222-8183. The
model number, serial number, date of purchase, and the name of the authorized Swisher dealer from
whom you purchased the product will be needed before any warranty claim can be processed.
THIS WARRANTY DOES NOT APPLY TO ANY INCIDENTAL OR CONSEQUENTIAL
DAMAGES AND ANY IMPLIED WARRANTIES ARE LIMITED TO THE SAME TIME
PERIODS STATED HEREIN FOR ALL EXPRESSED WARRANTIES. Some states do not
allow the limitation of consequential damages or limitations on how long an implied warranty may
last, so the above limitations or exclusions may not apply to you. This warranty gives you specific
legal rights and you may have other rights, which vary from state-to-state. This is a limited warranty
as defined by the Magnuson-Moss Act of 1975.
LIMITED WARRANTY
The manufacturer’s warranty to the original consumer purchaser is: This product is free from defects
i
n materials and workmanship for a period of one (1) year from the date of purchase by the original
consumer purchaser. We will repair or replace, at our discretion, parts found to be defective due to
materials or workmanship. This warranty is subject to the following limitations and exclusions:
1. Limitation This warranty applies only to products which have been properly
assembled, adjusted, and operated in accordance with the instructions
contained within this manual. This warranty does not apply to any
product of Swisher that has been subject to alteration, misuse, abuse,
improper assembly or installation, shipping damage, or to normal
wear of product.
2. Exclusions Excluded from this warranty are normal wear, normal adjustments, and
normal maintenance.
2
SAFETY PRECAUTIONS
3
• Read the manual. Learn to operate this machine safely.
•
Keep the operating speed LOW!!!!! Do not operate over 5 MPH (8 KPH).
• Allow only responsible adults who are familiar with these instructions to operate this
machine. Never allow children to operate this machine.
• Be sure the area is clear of other people before operating. Children are often
attracted to the machine and the operating activity. Never assume that children will
remain where you last saw them. Keep children under the watchful care of another
responsible adult.
• Watch for traffic when operating near or crossing roadways.
• Do not operate the attachment if it has been dropped or damaged in any manner.
Repair as necessary.
• Dress properly. Do not operate when barefoot or wearing open sandals.
• Do not operate the machine while under the influence of alcohol or drugs.
• Never tamper with safety devices. Check their proper operation regularly.
• Operate attachments up and down slopes. There is significant risk of overturns when
operating across slopes.
• Stop and inspect the equipment if you strike an object. Repair, if necessary, before
restarting.
• Never make adjustments or repairs with the engine running.
• Some components are heavy and may require help when lifting, especially once
the parts are assembled.
This Safety Alert Symbol indicates important messages in this
manual. When you see this symbol, carefully read the message that
follows and be alert to the possibility of personal injury.
Item # Part # Description Item # Part # Description
1 20671* Weldment - Frame, FM Plow 17 18953 Bolt - 5/8-11 X 8 1/2
2 4845 Bearing - .990"ID X 1.990"OD 18 NB614HT Washer - 1 X 1 1/2 10GA
3 19269* Weldment - Quick Disconnect 19 NB612 Nut - Nyloc 1"-8
4 20680Z Washer - .812"ID X 1.75"OD X 3/16 20 20685* Weldment - Shackle
5 20681Z Washer - 1.062"ID X 1.75"OD X 3/16" 21 NB244 Pin - Clevis 1/2 X 2 3/4
6 19371 Washer - .650"ID X 1.75"OD X 3/16" 22 NB247 Pin - Hair, #4
7 19734 Washer - 3/4"ID X 2"OD X 1/4" 23 20051 Pin - Clevis, Std 3/8 X 1 1/4
8 NB595 Nut - Lock Jam, 5/8-11 2 Way 24 NB127 Pin - Hair, #39
9 13997 Nut - 3/4-10; 2 Way 25 20684 Cable - Lanyard, 24"
10 8006Z Roller - Fairlead .875 OD X 3.188 26 8003 Fairlead - Assembly
11 8048 Bushing - .625 27 NB780 Bolt - Serr Flange, 3/8-16 X 3/4
12 NB674 Bolt - 3/8-16 X 4 1/2 28 NB779 Nut - Serr Flange, 3/8-16
13 NB272 Washer - SAE Flat 3/8 29 14316 Clamp - Wiring Harness
14 NB182 Nut - Nyloc 3/8-16 30 NB250 Bolt - 1/4-20 X 3/4
15 19332* Weldment - Caster, HD; Front Mount 31 NB180 Nut - Nyloc 1/4-20
16 19290 Tire/Wheel - 11 X 6.00-5, Smooth Not Shown 20669 Wiring Harness, Attachment Presence
4
PLOW BLADE MOUNT ATTACHMENT
P
ARTS DETAIL
When ordering replacement parts
*USE PAINT CODE: TK=BLACK
Assembling the Plow Blade to the Plow Blade Mount Attachment
TO ENSURE PROPER ASSEMBLY, CAREFULLY
FOLLOW ALL INSTRUCTIONS LISTED BELOW
5
Assembling the Plow Blade Mount Attachment to the Tractor
** Indicates parts that are included
w
ith the Plow Blade or the Tractor.
Connect the Plow Blade (sold separately) to the Plow Blade Mount
Attachment using Plow Mount Pin 2642TK** and Lynchpin NB506** as
shown in the diagram below.
Before connecting the Plow Blade Mount Attachment to the Tractor,
chain the Floorpan of the Tractor in the upright position as shown in the
diagram below. Refer to the Tractor Owner’s Manual for instructions.
The Plow Blade Mount Attachment connects to the Tractor in the same
manner as a Deck connects to the Tractor.
Pull Lock/Release Pins 19292** and rotate until they stay in the release
position.
Insert the Plow Blade Mount Attachment until it is completely seated and
rotate Lock/Release Pins 19292** until they lock the Plow
Blade Mount Attachment to the Tractor.
Connect both plugs of the Wiring Harness
(not shown) into the corresponding Wiring
Harness plugs of the Tractor.
62” Commercial Pro
P
low Blade 20100 Shown
6
Assembling the Lanyard to the Shackle
As
sembling the Shackle to the Winch Strap
TO ENSURE PROPER ASSEMBLY, CAREFULLY
FOLLOW ALL INSTRUCTIONS LISTED BELOW
The numbers in parenthesis
o
n this page refer to items
from the table on page 4.
** Indicates parts that are included
with the Plow Blade or the Tractor.
62” Commercial Pro
Plow Blade 20100 Shown
R
oute Winch Strap 20327** under Fairlead Roller 8006Z (10).
Connect Winch Strap 20327** to Shackle 20685 (20) using Clevis Pin
NB244 (21) and Hair Pin NB247 (22).
Connect one end of Lanyard 20684 (25) to Shackle 20685 (20) using
Clevis Pin 20051 (23) and Hair Pin NB127 (24).
7
TO ENSURE PROPER ASSEMBLY, CAREFULLY
FOLLOW ALL INSTRUCTIONS LISTED BELOW
Assembling the Lanyard to the Plow Blade
The numbers in parenthesis
o
n this page refer to items
from the table on page 4.
** Indicates parts that are included
with the Plow Blade or the Tractor.
62” Commercial Pro
Plow Blade 20100 Shown
I
nsert Lanyard 20684 (25) through Fairlead Assembly 8003 (26) toward
the Plow Blade.
Connect Lanyard 20684 (25) to the Plow Blade using 1/2-13 X 3 Bolt
NB131** and 1/2-13 Nyloc Nut NB281** as shown in the diagram below.
WHEN ORDERING PARTS, PLEASE HAVE THE
FOLLOWING INFORMATION AVAILABLE:
* PRODUCT - ________________
* SERIAL NUMBER - _______________
* MODEL NUMBER - _______________
TYPE - _______________
* PART NUMBER WITH PAINT CODE
* PART DESCRIPTION
TELEPHONE - 1-800-222-8183
FAX - 1-660-747-8650
SWISHER ACQUISITION INC.
1602 CORPORATE DRIVE, WARRENSBURG, MISSOURI 64093
PHONE 660-747-8183 FAX 660-747-8650
ade I The
USA
of US and Global Parts
OWNER’S MANUAL
swisherinc.com
Starting Serial #: L216-001001
20670
CHANGING YOUR LANDSCAPE SINCE 1945
Plow Blade Mount Attachment
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
