TOA HY-0871CL User manual

Brand: TOA

Model: HY-0871CL

Type: User manual

TOA HY-0871CL is a speaker mounting bracket designed for mounting TOA's ES-0871 Speaker System to a wall or ceiling, allowing for flexible placement and aiming of the speaker. It features adjustable angle slots for precise positioning, ensuring optimal sound coverage and clarity. Made of rolled steel plate with a black, semi-matte finish, it offers durability and seamlessly blends into various environments. The bracket includes all necessary hardware for secure installation, making it an ideal solution for both residential and commercial applications.

Please follow the instructions in this manual to obtain the optimum results from this unit.

We also recommend that you keep this manual handy for future reference.

HY-0871CL

SPEAKER MOUNTING BRACKET

INSTRUCTION MANUAL

SAFETY PRECAUTIONS

• Be sure to read the instructions in this section carefully

before use.

• Make sure to observe the instructions in this manual as

the conventions of safety symbols and messages

regarded as very important precautions are included.

• We also recommend you keep this instruction manual

handy for future reference.

Safety Symbol and Message Conventions

Safety symbols and messages described below are used

in this manual to prevent bodily injury and property

damage which could result from mishandling. Before

operating your product, read this manual first so you are

thoroughly aware of the potential safety hazards as well as

understand the safety symbols and messages.

• Install the unit only in a location that can structurally

support the weight of the unit and the mounting bracket.

Doing otherwise may result in the speaker falling down

and causing personal injury and/or property damage.

• Owing to the speaker's size and weight, be sure that at

least two persons are available to install the speaker.

Failure to do so could result in personal injury.

• Use nuts and bolts (not supplied with the unit) that are

appropriate for the ceiling's or wall's structure and

composition. If the ceiling or wall cannot withstand the

weight of both the speaker and bracket, the speaker may

fall, resulting in material damage and possible personal

injury.

• When mounting the speaker to a wall, ensure that the

entrance of the bracket's temporary-fixing slot is facing

upward. If not installed facing up, the speaker may fall

off, resulting in personal injury.

• Tighten each nut and bolt securely. Ensure that the HY-

0871CL has no loose joints after installation to prevent

accidents that could result in personal injury.

• Do not hang down from the bracket, as the speaker

system and bracket could fall, resulting in personal injury.

GENERAL DESCRIPTION

The HY-0871CL Speaker Mounting Bracket is specially

designed for mounting TOA's ES-0871 Speaker System to

a wall or ceiling.

NOMENCLATURE

INSTALLATION

1. Mount both Brackets L and R to a ceiling or wall using

four bolts for each bracket.

WARNING

Angle adjustment

slot C

Angle adjustment slot B

Angle adjustment slot A

Bracket R

Bracket L

Temporary-

fixing slot

Indicates a potentially hazardous

situation which, if mishandled, could

result in death or serious personal

injury.

Ceiling or wall mounting dimension (Unit: mm)

• When installing brackets as shown in Figure 1

742

819

898

190

300

357

592

672

748

357

300

190

Figure 1

Figure 2

• When installing brackets as shown in Figure 2

2. Out of four screws located on each of the speaker's top

and bottom panels, remove the following three (six in

total) from each panel.

Do not remove this screw.

(This nut is not used.)

Nut A (one each on top

and bottom panels)

Nut B (one each on top

and bottom panels)

Nut C (one each on top

and bottom panels)

Printed in Japan

133-05-318-60

Note : Do not leave hexagon bolts excessively loose

when installing them temporarily.

4. Fit the two temporarily-installed bolts into the temporary-

fixing slot of both Brackets L and R.

Temporarily-installed bolt with

its spring and plain washers

Plain washer

Spring washer

Hexagon bolt

Nut A (one each on top

and bottom panels)

4-5 mm

Speaker

• Wall mounting

Temporary-fixing slot

5. Move the speaker to install hexagon bolts in Nut B (two

places).

• Horizontal wall mounting

• Ceiling mounting

• Vertical wall mounting

Downward facing

angle of 15°- 75°

Maximum 509

463

446

Downward facing

angle 45°

Downward facing

angle 45°

Adjustable Speaker Mounting Angle Range

Unit: mm

Adjustable angle range differs

depending on the bracket's slot

or hole to use.

3. Run the bolt through its spring washer and plain washer,

and temporarily install it in Nut A on each speaker panel

as shown below. (In this case, do not fully tighten the

bolt but leave a gap of 4 to 5 mm between plain washer

and speaker panel to permit the bracket to be inserted.)

Temporary-fixing slot

• Ceiling mounting

• Wall mounting

Temporary-

fixing slot

Temporary-

fixing slot

Angle adjustment

slot B

Angle adjustment

slot B

Nut B

Nut A

• Ceiling mounting

6. Remove bolts from Nut A (two places). Move the

speaker again, and install a plain washer, a spring

washer and a hexagon bolt in Nuts A and C.

• Wall mounting

Nut C

Nut B

Nut A

Nut C

Nut B

Nut A

• Ceiling mounting

Note : When removing the hexagon bolt from Nut A,

ensure another hexagon bolt is installed securely

in Nut B, and support the speaker while removing

the bolt.

7. Adjust the speaker angle, then tighten all hexagon bolts

securely.

SPECIFICATIONS

Note : The design and specifications are subject to change

without notice for improvement.

• Accessories

Hexagon bolt W3/8"

............................................. 6

Spring washer (W3/8")

........................................ 6

Plain washer (W3/8")

........................................... 6

Finish Rolled steel plate, paint, black, semi-mat

Weight 5.5 kg

TOA HY-0871CL User manual

TOA HY-0871CL User manual

Related papers

Other documents