UMBRA RIMORCHI 31080/C Fitting Instructions Manual

Type
Fitting Instructions Manual
ISTRUZIONI DI MONTAGGIO
FITTING INSTRUCTIONS
INSTRUCTIONS DE MONTAGE
MONTAGEANLEITUNG
INSTRUCCIONES DE MONTAJE
DISPOSITIVO DI TRAINO TIPO
TOWING BRACKET TYPE
DISPOTIF DE REMORQUAGE TYPE
ANHAENGEVORRICHTUNG TYP
DISPOSITIVO DE CAREO TIPO
31080/C
PER AUTOVEICOLI
FOR CARS
POUR AUTOS
FUR KRAFTAHRZEUGE
PARA AUTOVEHICULO
RENAULT SCENIC AND
GRAND SCENIC ’03
TYPE
JM
2003
CLASSE E TIPO DI
ATTACCO
CLASS AND HITCH TYPE
CLASSE ET TYPE DE CROCHET
KLASSE UND BEFESTIGUNGSART
CLASES DE ACOPLAMIENTO
OMOLOGAZIONE
HOMOLOGATION
HOMOLOGATION
ZULASSUNG
APROBACION
CARICO VERTICALE MAX
S VALUE
MASSE VERTICALE MAXIMUM
ZUL. STUETZLAST
CARGA MAX. VERTICAL
F
e3 00 – 7185
(DIR. 94/20/CE)
S = kg 90
VALORE D
D VALUE
VALEUR D
D WERT
VALOR D
D = 8,7 kN
COPPIA DI SERRAGGIO PER VITI (8.8):
TORQUE SETTINGS FOR NUTS AND BOLTS (8.8):
COUPLE DE SERRAGE POUR VIS (8.8):
SCHRAUBENANZUGSMOMENT (8.8):
MOM. DE PRESION PARA TORNILLOS Y TUERCAS (8.8):
Cod. 31080/C
- Renault Scenic -
v. 1.0 01/01/2011
P. 1 / 6
8,7 kN
M6 = 10 Nm M8 = 25 Nm
M10 = 55 Nm M12 = 85 Nm
M14 = 135 Nm M16 = 200 Nm
www.umbrarimorchi.it
Tel. +39 075.5280260
Fax +39 075.5287033
Via Pizzoni 37/39
06132 Perugia
ITALY
SAFETY INSTRUCTIONS
Make sure that the towbar is suitable for the vehicle before starting the
installation.
For safety, all work involving towbar installation (incl. electrical components) must
be undertaken by skilled technicians.
Damaged components must be replaced with manufacturer’s spares and fitted by
qualified staff.
It is forbidden to make any modification or structural repair to towing assembly.
The towball must be kept clean and lubricated. For added safety, his diameter (50
mm) must be checked at regular intervals. If the towball measures less than 49 mm
after selected readings across the diameter, the towball must be replaced with a new
one.
After 1000 km of towing, check torque settings for nuts and bolts, in accordance
with the table.
Umbra Rimorchi cannot be held responsible for any defects in the product
caused by fault or by any injudicious use whatever of the user or a person he is
liable for.
Cod. 31080/C
- Renault Scenic -
v. 1.0 01/01/2011
P. 2 / 6
FITTING INSTRUCTIONS
31080/C RENAULT SCENIC
Remove any mastic from contact points then paint with anti-rust paint. The
necessary holes are already existing.
1 Remove bumper and discard the reinforcement bar, then remove the plastic
cover which is on the outside of the left side of the vehicle so to be able to reach
mounting point 02.
2 In case you are installing the tow bar on a “Grand Scenic” remove the black
masks located to the sides of the rear part where the seats are inserted.
3 Locate side arm B referring to holes 01 then tighten inserting the screws inside
and interposing the large washers.
4 Unscrew the screw under the chassis rail to allow the passage of the side left
side arm; locate side arm C referring to holes 01 and 02 then tighten inserting the
screws inside 01 and outside 02. In position 01 interpose large washers.
5 Interpose cross bar A to the B and C supports in correspondence of holes 03
then tighten.
6 Tighten all bolts and nuts as per torque settings
7 Connect the wirings to the socket.
8 Re-fit the rubber cover on the left side of vehicle.
9 Cut the inner bumper support as showed.
10 If you are mounting the tow bar on a “ Grand Scenic” cut again as showed in
layout 2 and then re-fit the black sides masks.
11 Re-fit bumper.
Rotating disappearing socket support
Cod. 31080/C
- Renault Scenic -
v. 1.0 01/01/2011
P. 3 / 6
Cod. 31080/C
- Renault Scenic -
v. 1.0 01/01/2011
P. 4 / 6
Cod. 31080/C
- Renault Scenic -
v. 1.0 01/01/2011
P. 5 / 6
Cod. 31080/C
- Renault Scenic -
v. 1.0 01/01/2011
P. 6 / 6
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6

UMBRA RIMORCHI 31080/C Fitting Instructions Manual

Type
Fitting Instructions Manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI