COMP Cams 89012-KIT is a valve spring set designed for Acura/Honda B-Series VTEC engines. It includes dual intake springs and single exhaust springs, providing optimal valve control and performance.
Key Features:
- Dual intake springs for increased stability at high RPM
- Tightly wound coils on the bottom of intake and exhaust springs for maximum performance
- Precisely engineered spring rates and installed heights for optimal valve timing
Benefits:
- Improved engine performance and responsiveness
- Increased power and torque
- Enhanced valve control for better fuel efficiency and emissions
COMP Cams 89012-KIT is a valve spring set designed for Acura/Honda B-Series VTEC engines. It includes dual intake springs and single exhaust springs, providing optimal valve control and performance.
Key Features:
- Dual intake springs for increased stability at high RPM
- Tightly wound coils on the bottom of intake and exhaust springs for maximum performance
- Precisely engineered spring rates and installed heights for optimal valve timing
Benefits:
- Improved engine performance and responsiveness
- Increased power and torque
- Enhanced valve control for better fuel efficiency and emissions
COMP Cams®
3406 Democrat Rd.
Memphis, TN 38118
Phone: (901) 795-2400 Fax: (901) 366-1807
www.compcams.com
Part #COMP4-104
Revised 6/28/06
#913 Acura B18 Valve Spring Set
Thank you for choosing COMP Cams® products; we are proud to be your manufacturer of choice. Please read
this instruction sheet carefully before beginning installation, and also take a moment to review the included
limited warranty information.
The COMP Cams® Acura/Honda B-Series VTEC valve spring set (Fig.
A) utilizes dual springs on the intake side and a single spring on the
exhaust side. Below are the information and diagrams to ensure correct
installation.
Installation Instructions:
Warnings and maintenance information!
It is important to orientate the outer valve spring of the intake and
exhaust (See Fig. B & C) with the *tightly wound coils on the
bottom. THE ORIENTATION OF THE INNER INTAKE SPRING
IS NOT CRITICAL.
*Note: To figure out which end is the tightly wound end start at
the end of the coil. Follow it around 180° (See Fig. D) then look
at the distance between the two coils. Now follow the same steps
from the other end of the spring. Whichever end is closest
together needs to be on the bottom.
INSTRUCTIONS
Dual Intake Spring
Installed Height: 60lbs at 1.375
Open Height: 220 lbs at .875
Coil Bind Height: .815
Spring Rate: 300 lbs per inch
Single Exhaust Spring
Installed Height: 43 lbs at 1.375
Open Height: 148 lbs at .875
Coil Bind Height: .815
Spring Rate: 210 lbs per inch
S
p
rin
g
s shown here with ti
g
htl
y
wound coils on bottom.
COMP Cams®
3406 Democrat Rd.
Memphis, TN 38118
Phone: (901) 795-2400 Fax: (901) 366-1807
www.compcams.com
Part #COMP4-104
Revised 6/28/06
Limited Warranty
Competition Cams, Inc. warrants that all of its products are free from defects in material and
workmanship, and against excessive wear for a period of (1) one year from the date of purchase. This
limited warranty shall cover the original purchaser.
Competition Cams, Inc.’s obligation under this warranty is limited to the repair or replacement
of its product. To make a warranty claim, the part must be returned within (1) one year of purchase to
the address listed below, freight prepaid. Items covered under warranty will be returned to you freight
collect.
It is the responsibility of the installer to ensure that all of the components are correct before
installation. We assume no liability for any errors made in tolerances, component selection, or
installation.
There is absolutely no warranty on the following:
A) Any parts used in racing applications;
B) Any product that has been physically altered, improperly installed or maintained;
C) Any product used in improper applications, abused, or not used in conjunction with the
proper parts.
There are no implied warranties of merchantability or fitness for a particular purpose. There are
no warranties, which extend beyond the description of the face hereof. Competition Cams, Inc. will
not be responsible for incidental and consequential damages, property damage or personal injury
damages to the extent permitted by law. Where required by law, implied warranties or merchantability
and fitness are limited for a term of (1) one year from the date of original purchase.
This warranty gives you specific legal rights and you may also have other legal rights, which vary from
state to state.
-
1
-
2
COMP Cams 89012-KIT Operating instructions
- Type
- Operating instructions
COMP Cams 89012-KIT is a valve spring set designed for Acura/Honda B-Series VTEC engines. It includes dual intake springs and single exhaust springs, providing optimal valve control and performance.
Key Features:
- Dual intake springs for increased stability at high RPM
- Tightly wound coils on the bottom of intake and exhaust springs for maximum performance
- Precisely engineered spring rates and installed heights for optimal valve timing
Benefits:
- Improved engine performance and responsiveness
- Increased power and torque
- Enhanced valve control for better fuel efficiency and emissions
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
COMP Cams 912-16 Operating instructions
-
COMP Cams 23-707-9-camshaft crb3 rx308r-8 Operating instructions
-
COMP Cams 127400-4.6/5.4-liter 2 and 3 valve engines camshaft Operating instructions
-
-
COMP Cams 89875C-16 Operating instructions
-
-
-
-
-