Page is loading ...
DISPENSING
PLEASE NOTE:
❐ Pressing the same dose key
during dispensing can stop the
selected dose (not available for
Self confi guration).
❐ In case of a milk-based
dose, press once to stop milk
dispensing, and once again
to stop coffee dispensing; the
sequence depends on the type of
dispensing (not available for Self
confi guration).
1
PLEASE NOTE:
❐ Pressing the same dose key
during dispensing may stop the
selected dose (not available for
Self confi guration).
WARNING:
❐ Handle the hot water spout with
caution because it might cause
burns due to high temperature.
❐ Hot water cannot be dispensed
simultaneously with steam.
COFFEE/CAPPUCCINO
DISPENSING
Place a cup under the coffee
dispenser, and press the desired
dose key. For Shift doses, press
the Key No3 (Shift) fi rst and then
the desired dose key.
The display shows:
Where “XXXXXXXX” indicates the
selected dose key name.
HOT WATER DISPENSING
Place a cup under the hot water
outlet, and press the hot water
key dose. Dispensing will be
automatically stopped once the
programmed dose is over. The
display shows:
XXXXXXXX
HOT WATER
2
STARTING UP
When the set-up temperature is
reached, the display shows:
For machine confi guration Standard
or Self
SELECT DRINK
After checking that the machine
door is closed and the ground bin
is inserted, press the key No.1
(ON/OFF) to turn ON the machine.
Fill in the required amount for
daily consumption in order to
keep coffee always fresh.
Warning: during this stage
remove any jug with milk or any
other kind of liquid from the
steam wand!
FILL IN BEAN HOPPER
4
3
DECAFFEINATED DISPENSING
(NOT AVAILABLE FOR SELF
CONFIGURATION)
Place a cup under the coffee
dispenser and open the
decaffeinated coffee door, the
display shows :
❐ Pour in the powdered coffee
❐ Close the decaffeinated door
❐ Press the desired dose key, the
display shows:
PLEASE WAIT
XXXXXX
Where indicates that the
selected dose will be dispensed
without the activation of the
grinders.
PLEASE NOTE:
If the decaffeinated door is not
closed, or if the dose button is
not selected, the machine will
automatically cancel this function
after 20 seconds. The coffee group
will carry out a cleaning cycle of
the brewing chamber. The display
shows:
EXTRAMILK DISPENSING (ONLY
LM MACHINE, NOT AVAILABLE
FOR SELF CONFIGURATION)
Press any milk-based key and
keep it pressed, after 2 seconds
foamed milk will start being
dispensed, the display shows:
By releasing the pressed key,
dispensing will be stopped.
EXTRA MILK
QUICK START GUIDE
COFFEE MACHINES
F10 - F20
DO NOT leave the steam wand
into any liquid at any time
6
STEAM WAND USE AND CLEANING AUTOMATIC CLEANING OF COFFEE GROUP
Clean the steam wand by means
of a cloth.
5
After using the steam wand pull
down the steam tap to purge the
nozzle.
4
Keep key No.2 (Clean) pressed
for fi ve seconds. For machine in
SELF confi guration keep key No.
1 (ON) and 2 (Clean) pressed for
fi ve seconds.
1 3
Verify that the display shows
GROUP CLEANING, if not press key
No. 4 or 5 to select it.
2
SELECT CLEANING
GROUP CLEANING GROUP CLEANING
9 10
Wait until the cleaning cycle is
over.
Pull up the steam tap to stop the
delivery before removing the jug.
3
Before using the steam wand pull
down the steam tap to purge the
nozzle.
1
Use the steam wand to foam or
heat any liquid into the jug by
handling the rubber protection.
2
SELECT CLEANING
Group Cleaning
Insert the detergent tablet into
the decaffeinated chute and close
the cover. For machine in SELF
confi guration open the frond or
and insert the detergent tablet
into the brewing chamber, then
close the door.
GROUP CLEANING
Insert the cleanser
FOR F10: press key No.2 (Clean) to
start the cleaning cycle.
GROUP CLEANING 1
11
SELECT DRINK
At the end of the cleaning cycle
the display will show
4
FOR F20: press key No.2 (Clean) to
select group cleaning.
GROUP CLEANING 1/2
5
GROUP CLEANING X
FOR F20: press key No.4 or 5 to
select group 1 or 2, then press
key No. 2 (Clean) to start the
cleaning cycle.
6
GROUP CLEANING
OPEN FRONT PANEL
Lift the machine door.
7
GROUP CLEANING
CLOSE DOOR
Clean the group, the chute and
the piston o-ring from any coffee
residues.
8
GROUP CLEANING
CLOSE DOOR
Close the front door.
WE STRONGLY RECOMMEND TO USE AND CLEAN THE STEAM WAND AS ABOVE SHOWN
PLEASE NOTE:
- We suggest repeating the group
cleaning cycle by using only water.
- For F20 repeat group cleaning for the
second group.
MANUAL CLEANING OF MILK FROTHER
AUTOMATIC CLEANING OF MILK FROTHER
Prepare a solution of water
and detergent (q.ty 200 ml.)
by following the instructions
indicated in the product.
2
For cleaning operations, we
strongly recommend to use the
following detergent products
CLEANING TABLETS
MILK FROTHER
CLEANER
6
Take the milk infeed tube out of
the milk box.
13
Insert the milk infeed tube into a
container with detergent.
PLEASE NOTE: a) For F20 repeat the milk frother cleaning for the second group (if
present)
b) Do not interrupt the cleaning cycle. If the cleaning cycle is interrupted by any type of
operation unrelated to the procedure, when the machine functioning is set back again,
the cleaning cycle will automatically be activated.
b)
Only in case that after the automatic cleaning process the milk frother is not properly
dispensing, carry out a manual cleaning; see the following steps.
Remove the milk frother from the
coffee outlet
1
Remove the milk frother from its
holder and disconnect silicone
tubes No. -3- and -4-
23
Disassemble the milk frother in all
its parts (fi rst by turning and then
by pulling as shown in the picture)
and wash it either by hand or in a
dishwasher. Make sure that all the
holes are free from milk residues
and that the O-rings are in good
condition.
OTHER RECOMMENDED CLEANING
At the end of the cleaning cycle
rinse the drip tray in a sink.
At the end of the cleaning cycle
rinse the grounds bin in a sink.
Once a month clean the hopper
by means of a cloth and approved
food detergent.
4
Keep key No.2 (Clean) pressed
for fi ve seconds. For machine in
SELF confi guration keep key No.
1 (ON) and 2 (Clean) pressed for
fi ve seconds.
SELECT CLEANING
GROUP CLEANING
65 7 8
5
Press key No. 4 or 5 to select
MILKER CLEANING.
SELECT CLEANING
MILKER CLEANING
Press key No.4 or 5 to select
MILKER CLEANING.
SELECT CLEANING
MILKER CLEANING
At the end of the cleaning cycle
the display shows:
- Put the infeed pipe into a glass
of cold water
- Press the key No.2 (Clean), the
milk frother will carry out another
cleaning cycle using only water.
CLEAN AGAIN USING ONLY WATER
PRESS CLEAN KEY
Press key No. 2 (Clean) to
confi rm.
MILKER CLEANING 1
Press key No.2 (Clean) to confi rm.
MILKER CLEANING 1
Press key No.4 or 5 to select
milker cleaning 1 or 2.
MILKER CLEANING 1
Press key No. 2 (Clean) to
confi rm.
MILKER CLEANING 1
❐ FOR F10
❐ FOR F20
MILK FROTHER ADJUSTMENT
INFORMATION PROCEDURE AND DISPENSING RESET
MACHINE FUNCTIONS MESSAGES
Foam setting
The milk frother is equipped with a FOAM REGULATOR which sets the quantity
of air needed to froth milk.
Turn the ring nut clockwise for thicker foam (small bubbles), or turn it
anticlockwise for more voluminous foam (large bubbles).
1
Milk temperature setting
The milk frother is equipped
with a MILK TEMPERATURE
REGULATOR which reduces the
quantity of sucked milk.
Turn the regulator clockwise to
increase the milk temperature, or
turn it anticlockwise to reduce it.
2
OPEN THE FRONT DOOR TO ACCESS THE FOLLOWING ADJUSTMENTS (ONLY LM MACHINE)
PLEASE NOTE: for all other messages please refer to your service center.
PLEASE NOTE: the total cashing will be calculated if selling price has been set for each dose.
1
Alarm for machine door position.
CAUSE: The front door is open;
the micro switch does not touch
the door
RESULT: Shutdown of the machine
functions
SOLUTION: Close the door and
turn the machine ON
OFF
OPEN DOOR
2
GROUNDS BIN FULL
CAUSE: Grounds bin full; the
number of coffee grounds in the bin
has reached the programmed value
RESULT: Shutdown of the coffee-
based dispensing selections
SOLUTION: Remove the grounds
bin and empty it, replace the
grounds bin when the display
shows:
3
Alarm of too much coffee in the
brewing chamber
TOO MUCH COFFEE
GROUNDS BIN OPEN
Full grounds bin alarm
CAUSE: There is too much coffee in
the brewing chamber, or the piston
o-ring is dirty and the piston cannot
enter into the brewing chamber
correctly
RESULT: The machine interrupts
the coffee dispensing
SOLUTION: Carry out an automatic
cleaning of the group
❐ FOR F10 ❐ FOR F20
To enter the programming
environments proceed as follow:
The above message indicates the
number of “extramilk” doses that
have been made.
- Press key N°2 (Clean), the
display shows:
- Press key N°2 (Clean), the
display shows:
- If you want to reset the doses
counters, press key No.4 or 5 to
select YES, then press key No.
2 (Clean) to confi rm reset. The
display shows:
- After few seconds the display
shows:
The above message indicates the
number of “Group cleaning” that
have been made
- Press key N°2 (Clean), the
display shows:
The above message indicates the
number of “Milker cleaning” that
have been made
- Press key N°2 (Clean), the
display shows:
Where XXXXX indicates the total
cashing of the machine.
Press the key dose whose number
of drinks you want to display; the
display shows:
Where: “XXXXXX” indicates the
name of the selected button
GR “Z” indicates group 1 (Left)
or 2 (Right) and “K” indicates the
number of key.
0 YY indicates the number of
cup dispensed drinks
JJ indicates the number of
decaffeinated dispensed drinks
(only for left group).
- Press the key No.3 (Shift).
The display shows the number of
“Shift” drinks:
Where: “XXXXXX” indicates the
name of the selected button
GR “Z” indicates group 1 (Left)
or 2 (Right) and “K” indicates the
number of key.
0 YY indicates the number of
cup dispensed drinks
JJ indicates the number of
decaffeinated dispensed drinks
(only for left group).
- Press key N°2 (Clean), the
display shows:
- press key No.1 to turn the
machine OFF
- keep press key No.2 (Clean)
pressed while pressing key No.1
(ON/OFF); the display shows:
DOSES INFORMATION
SELECT BUTTON
GROUP CLEANING
XXXX
RESET DOSES COUNT.
NO
RESET DOSES COUNT.
PLEASE WAIT
MACHINE OFF
MILK CLEANING
XXXX
TOTAL CASHING
XXXX
EXTRAMILK
XXXX
GR Z K
XXXXXX
0 YY YYY
GR Z K
XXXXXX
0 YY YYY
IMC S.p.A. Via Industriale, 1 · 24040 Chignolo d’Isola (BG) Italy · Tel. +39 035 905440 · Fax +39 035 905447 · www.carimali.com · www.macco.it
The Manufacturer reserves the right to modify the equipment presented in this publication without notice.
www.carimali.com
NT-000927-GB videocomp
/
