Dynalite MH2065v User manual

Brand: Dynalite

Model: MH2065v

Type: User manual

DYNALITE INC

1050 Commerce Ave ● Union ● NJ ● 07083

908-687-8800 Phone ● 908-686-6682 Fax

www.dynalite.com

Dynalite Lighting Controls and

System Accessories

Instruction Manual

For Model MH2065v

Fan Cooled Strobe Head

Replacement of Modeling Lamp

1. Unplug the flash head

from the power pack

and allow the flash

head to cool before

touching the modeling

lamp.

2. Remove flash head

accessories if present.

3. Remove the flash tube from the head in or-

der to reach the modeling lamp.

4. Remove the modeling lamp by carefully

griping it with a soft cloth and pulling

straight out.

5. Install the new lamp by aligning the pins

with the socket and press the lamp in place.

Please note: Do not touch the new lamp with your hands.

Oils from your hands can cause premature failure of the

lamp or could cause an unexpected shattering of the lamp.

Replacement of the Flash Tube

1. Unplug the flash head

from the power pack

and allow the flash head

to cool before touching

the flash tube.

2. Remove flash head ac-

cessories if present.

3. Remove the flash tube by rocking and or

pulling the outer edge of the reflector as-

sembly out of the flash housing.

4. Install the new flash tube assembly by align-

ing the three connection pins with the three

connection sockets inside the flash housing.

Ensure that the connection pins are aligned

correctly and in the proper configuration

before installing the flash tube assembly.

Gentle push the reflector/flash tube assem-

bly until the edge of the reflector is flush

with the outer edge of the flash housing.

Note: Use only the appropriate flash tube.

RR-GH RR-4G

RR-AFBD RR-AF

RR-50 RR-80

RR-AR SR-65SN

UCBW-36

UBBW-44

UQSS-48

R-11/20/2013

DYNALITE MH2065v INSTRUCTIONS

Important Safeguards

When using this flash equipment, include the fol-

lowing safety precautions.

· Read and understand ALL instructions and

specifications before using your Dynalite

equipment.

· Care must be taken when handling the flash

heads as injury could occur from touching the

modeling lamp(s) or flash tube(s).

· Do not operate a power pack or flash head

with a damaged cord or if the unit has been

dropped and is visually damaged.

· If an extension power cord is necessary, a

suitable current rating should be used. Cords

rated for less than 15 amps may overheat.

· Care should be taken to arrange the cord so

that it will not be tripped over or pulled from

the electric source outlet.

· Unplug the power pack from the electrical

outlet when not in use. NEVER yank the cord

to pull the plug from the electrical outlet.

· Let flash heads cool completely before putting

them away. Loop flash cables in an 8” to 10”

diameter coil when storing.

· DO NOT allow power cord(s) or flash head

cable(s) to hang on or touch hot surfaces.

· To avoid electrical shock hazard, power cord

(s) or flash head cable(s) must be properly

grounded. DO NOT attempt to disassemble

the power pack. Incorrect reassembly could

cause an electrical shock hazard when a power

pack is subsequently used. Take it to a quali-

fied Dynalite Service technician when service

is required.

· When the power pack is not in use for one

month or more, it is wise to periodical plug

the power pack in and turn it ON for a couple

of hours. It is not necessary to operate a flash

head during this “idling” time.

Standard Flash Head Features

· UV Color Corrected Flash Tube (2000 w/s

part number 2406

· Model Lamp 300 W, Part Number 0521

· Optional Model Lamp 650 W, Part Number

0520

· Universal Light stand Mounting (5/8”)

· Umbrella Mount (9mm hole)

· Protective Flash Head Cover

Setting Up The MH2065v Flash Head

1. Unpack your new Dynalite Flash Head and

make sure that all the items are accounted

for and in accordance with the parts descrip-

tion list.

2. Before firing the flash head, be certain to

remove the plastic flash head protective

cover (Yellow Cap).

3. Mount the flash head to an appropriately

sized (5/8”) and secure the flash head to the

light stand using the locking knob  (see

Parts Designation).

4. With the power pack OFF, connect the

power pack cable to the head cable socket

on the flash head. With the power pack

OFF, connect the other end of the power

pack cord to the power pack socket. Ensure

that both connectors are securely fastened

before turning the power pack ON.

Note: When using the optional 650W Model-

ing lamps in the MH2065v flash heads use no

more than two (2) flash heads in a power

pack at one time, and only one per side

(bank)

MH2065v Parts Description











Flash Tube (2000 W/s part # 2406)

Modeling Lamp (300 Watt part # 0521 or

optional 650 Watt, part #0520)

Tilt Head

Light Stand Swivel Block (part #P60101)

Locking Tilt Head Handle,

(Multi-position Ratcheting, (part# C47098)

Umbrella Locking Knob (part# C47103)

‡ Illuminated Model Lamp Switch

ˆ Flash Cable Socket

‰Cooling Fan

Š Umbrella Mounting Hole 9mm.

















Dynalite MH2065v User manual

Brand: Dynalite

Model: MH2065v

Type: User manual

Download PDF

report

Dynalite MH2065v User manual

Dynalite MH2065v User manual

Related papers

Other documents