Rokonet ORBiT-14 Installation guide

Installation Manual

ii

Important Notice

This manual is delivered subject to the following conditions and restrictions:

✦ This manual contains proprietary information belonging to Rokonet Electronics

Ltd. Such information is supplied solely for the purpose of assisting explicitly

and properly authorized users of the system.

✦ No part of its contents may be used for any other purpose, disclosed to any

person or firm or reproduced by any means, electronic or mechanical, without

the express prior written permission of Rokonet Electronics Ltd.

✦ The text and graphics are for the purpose of illustration and reference only. The

specifications on which they are based are subject to change without notice.

✦ Information in this document is subject to change without notice. Corporate and

individual names and data used in examples herein are fictitious unless

otherwise noted.

Installation Manual

iii

Customer Information

TELEPHONE CONNECTION (Ref.: FCC Part 68)

1. This equipment, Alarm Control Panel, brand named Orbit-14 (RP214MA0000A), complies with

Part 68 of the FCC Rules and the requirements adopted by the ACTA. On the bottom panel of

this equipment is a label that contains among other information, a product identifier in the format

US:RKEAL10BRP214MA. If requested, this number must be provided to the telephone company.

2. This equipment is designed to be connected to the telephone network using a terminal block,

which is Part 68 compliant and properly installed RJ31X connector. See Installation Instructions

for details.

3. The REN is used to determine the number of devices that may be connected to a telephone line.

Excessive RENs on a telephone line may result in the devices not ringing in response to an

incoming call. In most but not all areas, the sum of RENs should not exceed five (5.0). To be

certain of the number of devices that may be connected to a line, as determined by the total

RENs, contact the local telephone company. The REN of alarm system is part of the product

identifier that has the format US:RKEAL10BRP214MA.

4. If the Alarm Control Panel causes harm to the telephone network, the telephone company will

notify you in advance that temporary discontinuance of service may be required. If advance

notice is not practical, you will be notified as soon as possible. Also, you will be advised of your

right to file a compliant with the FCC if it is necessary.

5. The telephone company may make changes in its facilities, equipment, operations or procedures

that could affect the operation of the equipment. If this happens the telephone company will

provide advance notice in order for you to make necessary modifications to maintain

uninterrupted service.

6. If trouble is experienced with the Alarm Control Panel, for repair or warranty information please

contact Rokonet Industries USA Inc 2822 NW 79th Ave. Miami, Florida 33122 USA, phone

number 305 592 3820, URL: [email protected].

If the equipment is causing harm to the telephone network, the telephone company may request

to disconnect the equipment until the problem is resolved.

7. The control panel installation is described in the Installation Manual. Connection to telephone

company provided coin service is prohibited. Connection to party lines service is subject to state

tariffs.

8. Alarm Control Panel must be able to seize the telephone line and place a call in an emergency

situation. It must be able to do this even if other equipment (telephone, answering system,

computer modem, etc.) already has the telephone line in use. To do so, the alarm control panel

must be connected to a properly installed RJ31X jack that is electrically in series with and ahead

of all other equipment attached to the same telephone line. Proper installation is depicted in the

figure below. If you have any questions concerning these instructions, you should consult your

telephone company or a qualified installer about installing the RJ31X jack and Alarm Control

Panel for you.

Installation Manual

iv

Computer

Answering

System

Fax Machine

Telephone

Unused

RJ-11

Jack

Unused

RJ-11 Jack

RJ-31X

Jack

Telephone

Line

Network

Demarcation

Point

Network

Service

Provider's

Facilities

Customer Premises Equipment and Wiring

Alarm

Dialing

Equipment

RADIO FREQUENCY INTERFERENCE (Ref.: FCC Part 15, Para. 15.105)

This equipment has been tested and found to comply with the limits for a Class B digital device

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates, uses, and can

radiate radio frequency energy and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. However, there is no guarantee that interference

will not occur in a particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the following measures:

1. Reorient or relocate the receiving antenna.

2. Increase the separation between the equipment and the receiver.

3. Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

4. Consult the dealer or an experienced Radio/TV technician for help.

CHANGES OR MODIFICATIONS (Ref.: FCC Part 15, Para. 15.21 and 15.27)

Changes or modifications to this unit not expressly approved by Rokonet, Ltd., could void the user's

authority to operate the equipment.

Installation Manual

v

CE Declaration of Conformity

We, the undersigned,

ROKONET ELECTRONICS LTD.

RISHON LEZION, HACHOMA ST. 14

ISRAEL

PHONE: (972) 3 9616555

FAX: (972) 3 9616584

Certify and declare under our sole responsibility that the following equipment:

Brand Type Product Description

Orbit -14 RP214MC0000A Control Panel with wired accessories

(including cables)

was tested to and conforms with the requirements included in following standards:

Standard 5/1999/EC Article Note

EN 60950:00 3(1)(a) 1

EN 301 489-3 v.1.2.1 3(1)(b) 1

EN 50130-4:95+A1 (98) 3(1)(b) 1

TBR21:98+ETSI EG 201 121 v.1.1.3 / 2

Note 1: Full Orbit 14 system.

Note 2: Main unit (additionally).

and therefore complies with the requirements and provisions of the Council Directive

1999/5/EC of the European Parliament and of the council of 9 march 1999 on Radio

equipment and Telecommunications Terminal Equipment and the mutual recognition

of their conformity and Annex III (Conformity Assessment procedure referred to in

article 10(4)).

20 February 2003

David Kartoun

CTO

Installation Manual

vi

Installation Manual

1

TABLE OF CONTENTS

Introduction to the ORBIT-14 3

Main Features 3

Technical Data 5

Installation 7

Before You Begin 7

Mounting the Control Panel 7

Wiring the Main Panel 8

Connecting to Ground (Earth) 8

Telephone Line Connection 10

Connecting AC Power 10

Zone Connections 10

Wiring Auxiliary Devices 12

Bell Tamper 12

Box Tamper 12

Utility Output Connections 13

Connecting the J4 Connector 14

Keypad Connection 15

Connecting the J3 SIG IN Connector (Signal in Voice Mail) 15

Installer Programming 16

The Keypad 16

Restoring Factory Defaults to the ORBIT-14 16

Introduction to Programming 16

Programming Your ORBIT-14 17

Viewing the Contents of a Location 17

Locations Whose Contents Occupy More Than One Digit 18

Audible Tones and Error Beeps 18

Programming Installer Parameters 18

Programming Time Out 19

Programming Tutorial 19

Programming Locations: 21

General System Parameters: Locations 000-005 21

System Codes: Locations 006-010 22

System Time Definitions: Locations 011-016 23

Installation Manual

2

Zone Types and Sounds: Locations 017-030 24

Zone Response Time & Group Masking: Locations 031-044 27

Zone Termination & Tamper Sound: Location 045 27

Utility Outputs: Locations 046-051 28

Communication Parameters: Locations 052-055 32

Dialler Control 1: Location 052 32

Dialler Control 2: Location 053 34

Central Station Pulsed Protocols: Location 054 34

Automatic Central Station Protocols: Location 055 36

Upload/Download Rings: Location 056 37

Swinger Shutdown Limit: Location 057 37

System Controls: Locations 059-060 38

Sub Installer Restriction Level: Location 061 41

Communicator Reporting Codes: Locations 062-168 42

Reporting Codes for Alarm Events 42

Restore Codes 42

Other Reporting Codes 43

Trouble Reports and Restorals 45

Appendix 1: Installer Programming Worksheet 46

Appendix 2: Contact ID & SIA Report Codes for Orbit-14 48

Appendix 3: Summary of User’s Commands 50

Installation Manual

3

Introduction to the ORBIT-14

The ORBIT-14 is a fully featured security system, providing solutions for alerting and

reporting premises alarm signals.

The ORBIT-14 addresses the needs of many homes, offices, and small businesses.

Its operation is designed around microprocessor and EEPROM (Electrically Erasable

Programmable Read-Only Memory) technology, which stores the system’s operating

program and its programmable parameters, without the need for a source of power.

System programming may be performed from any ORBIT-14 keypad, or from an LCD

Programming Keypad designed specifically for this purpose.

Remote and local system programming is also possible through the use of Rokonet’s

Upload/Download software.

Main Features

Zones

• 14 Programmable Intrusion Zones

• 12 zones on main board using zone doubling.

• 2 zones on keypad

• 3 Keypad Emergency Zones (Panic, Fire, Special Emergency)

Alarm Sounder Output

• Programmable Bell/Siren or Loudspeaker Output

• Capacity: 900 mA (maximum)

Auxiliary Output for Peripheral Devices

• Capacity 600 mA MAX from all AUX terminals

Built-In Digital Communicator

• For Central Station communications (two phone numbers), Upload/Download

functions and follow-me functions

Keypads

• Up to five LED/LCD keypads can be connected

Utility Outputs

• 1 relay output 3A

• 1 transistor-driven (open-collector) 500 mA triggered output

• 1 transistor-driven (open-collector) 70 mA triggered output

• Expandable to six outputs

Security Codes

• 2 Installer Codes

• 1 Master (User) Code

• 19 Codes (all may be used as duress code)

Installation Manual

4

Periodic Testing

• Daily test report to central station

Optional Peripherals

• Four relay-output expansion modules

• Voice Module

Event Log

• Event log of 250 events

Tamper Protection

• Box Tamper input (NC)

• Bell Tamper input (using 2.21 KΩ resistor)

• Keypad Tamper (Wall & cover)

Automatic Arming

• Daily automatic arming

Orbit 14 Main Panel Types:

P/N Description

RP214MA0000A Orbit 14 Main Panel. Telephone impedance 600Ω. Complies

with FCC Part 68 regulation.

RP214MB0000A Orbit 14 Main Panel. Telephone impedance 900Ω.

RP214MC0000A Orbit 14 Main Panel. Complies with the TBR21: 98+ETSI EG

201 121 v.1.1.3 regulation.

RP214MZ0000A Orbit 14 Main Panel. Complies with the local Czech telephony

system requirements.

Installation Manual

5

Technical Data

Main Panel

Input power 16.5 V AC 40 VA via transformer

Rechargeable standby battery 12 V 7 A-Hours

Auxiliary Power 12 V DC 600 mA maximum

Bell/LS Sounder output 12 V DC 900 mA maximum

Programmable outputs 1 X Relay output 3A

1 X Open collector Active pull down 500 mA maximum

1 X Open collector Active pull down 70 mA maximum

Cabinet Dimensions: 296.2 X 262.3 X 87.5 mm ( 11.66 X 10.32 X 3.44”)

Weight 2.4 kg ( 5.29lb)

Main Board (dimensions / weight): 96 X 185 mm (3.77 X 7.28 “) 0.23Kg (0.51 lb)

Fuses F1: Battery Power 3.15 A

AUX Automatic fuse

Bell Automatic fuse

Keypads

6 / 8-Zone Keypad 14-Zone Keypad LCD Keypad

Current

consumption:

18 mA typical, 30 mA

maximum

18 mA typical, 37 mA

maximum

75mA maximum

Control panel

connections:

4-wire up to 300 ft (100

m) from panel

4 -wire up to 300 ft (100

m) from panel

4 -wire up to 300 ft (100

m) from panel

Dimensions: 110X130X25 mm

(4.33 X 5.11 X 1“)

110X130X25 mm

(4.33 X5.11X 1“)

162 X 122 X 30 mm

(6.37 X 4.8 X 1.18“)

Weight: 0.19 kg (0.42 lb) 0.19 kg (0.42 lb) 0.25kg (0.55 lb)

Utility Output Expansion Module

Relay row

Current consumption: 10mA typical, 50mA max

Control panel connections: 4-wire up to 300 ft (100m) from panel

Contacts: 1 relay 3A, 3 relays 0.5 A, 24 V DC

Dimensions: 53X85 mm (2.1X3.35“)

Weight: 80 gr (0.18 lb)

Expansion Voice Module

Input Power: 12 V DC

Current consumption: 6 mA, typical / 26 mA maximum

Dimensions: 66 X 66 X 18 mm (2.59 X 2.59 X 0.70“)

Weight: 20.44 gr (lb)

NOTES:

For proper operation it is recommended to connect the voice module at least 20 cm from the

main panel.

Installation Manual

6

Max. Run Length from Panel to Keypad

AWG 19 20 22 Wire

Ø (mm) 0.9 0.8 0.6

Meter 200 166 100 Length

Feet 660 547 330

Bell Loudspeaker Wiring Table (Distance in Feet)

18 19 20 22

1 0.9 0.8 0.6

AWG

Ø mm

Max.

Current mA Feet Meter Feet Meter Feet Meter Feet Meter

100 780 238 625 190 495 151 310 95

300 260 79 208 64 165 50 103 32

650 120 37 96 30 76 23 48 15

Detectors Distance in Feet

18 19 20 22 24

1 0.9 0.8 0.6 0.5

AWG

Ø mm

Max.

Current mA Feet Meter Feet Meter Feet Meter Feet Meter Feet Meter

20 3920 1195 3100 945 2460 750 2460 472 1550 296

30 2600 793 2060 628 1640 500 1640 314 1030 197

40 1960 597 1550 472 1230 375 1230 236 775 148

Installation Manual

7

Installation

Before You Begin

Be sure the actual work is performed by experienced personnel, licensed to carry out

security system installations and capable of implementing all applicable requirements

of the National Fire Protection Association (NFPA-70 and NFPA-74), as well as any

federal, state, and local codes – along with any safety guidelines and regulations

which might apply.

Mounting the Control Panel

1. Mount the ORBIT-14’s metal cabinet at a protected dry location, near a source of

unswitched AC Power, a good ground, and access to telephone service. Use the

proper hardware (e.g., anchors, toggle bolts), as required, to insure a suitable

mounting.

2. Thread all electrical wiring through a convenient hole in the metal cabinet. To

prevent potential damage, be sure that live AC power is NOT present and that the

Standby Battery is NOT connected. (Refer to page 8). Your wiring may include

any and all of the following:

• Connections to Hardwired Zones

• Connections to devices requiring Uninterrupted Auxiliary Power (e.g., PIRs,

Glass Break Detectors)

• Connections to Smoke Detectors requiring Reset table Power

• Connections to any External Sounders

3. Have a Standby Battery ready (typically 12 VDC, 7 AH), but do not connect it at

this time.

4. If using a Key-switch, use a momentary key-switch. The receiver (if used) must

give a pulse output and not on/off.

Safety Warnings

• When the panel is powered, mains voltage is present on the main PCB. To

prevent risk of electric shock, disconnect all power (AC transformer and battery)

and phone cord before servicing. On no account should mains power be

connected to the PCB other than the main terminal block.

• For AC mains connection, a readily accessible disconnect device shall be

incorporated in the building installation wiring.

• For continued protection against risk of fire, replace fuses only with fuses of

the same type and rating

• There is a risk of explosion if the battery is replaced by an incorrect battery type.

Dispose of used batteries according to the instructions. (The control panel is

designed to work with a 12 volt, 7 Amp-hour sealed lead battery as a back up for

the primary power supply.)

Installation Manual

8

• Do not short the terminals of the transformer together. This causes the internal

fuse to blow. The transformer must be connected to a 230 VAC 24-hour outlet,

which must be controlled by an approved over-current protection device.

• The control is designed with reverse polarity protection on the battery charging

circuit; however, prolonged improper connection of the battery to the control

panel results in damage. Power should remain disconnected until all connections

have been made and checked for accuracy.

Wiring the Main Panel

Connecting to Ground (Earth)

Connect the metal box and the door of the metal box to mains earth (ground), as

shown in the diagrams below. Refer also to What Makes a Good Ground, page 9.

IMPORTANT:

Connecting to ground must be performed according to the applicable local or national electrical

codes.

Installation Manual

9

Grounding the Metal Box

What Makes a Good Ground?

Grounding provides a degree of protection against lightning and induced transients

for any piece of electronic equipment that may, due to lightning or static discharge,

experience permanent or general malfunctions. The ideal ground is considered to be

a unified earth ground in which an 8-foot copper-clad rod, located close to the existing

power and telephone ground rods, is sunk several feet into the earth. Appropriate

hardware and clamps are then used to electrically connect each of these rods

together and then to the ground terminal of the device to be protected.

Installation Manual

10

It may be possible to use an existing electrical ground on the premises if one is close

enough to the Main Panel. Ideally, that ground can be obtained at the metal service

panel where the incoming electrical power originates. When connecting the ground

wire, use a solid 14-gauge wire [or larger (numerically lower) size] connected

between the ORBIT-14’s GND terminal and an acceptable electrical ground

connection. Keep this wire as short as possible and do not run it in conduit, coil it,

bend it sharply, or run it alongside other wiring. If you must bend it or change its

direction, it should have a radius of at least 8 inches at the point from which it is bent.

If in doubt, you may want to enlist the help of a licensed electrician.

Telephone Line Connection

These lines are typically derived from an installed RJ31X jack.

To connect telephone lines:

1. Connect the incoming telephone line to the Main Panel's LINE terminals.

2. Connect any telephone on the premises to the SET terminals.

Connecting AC Power

Connect the 230V AC to the mains fuse input terminal block (via 16.5VAC 40VA

transformer) and fasten the AC cord to the metal box using adjustable clamps.

NOTES:

DO NOT apply main power at this time.

Be sure to connect the live wire of the AC power through the AC fuse.

Do not plug in the transformer at this time.

Zone Connections

Connect each zone to the appropriate zone terminal and its related COM terminal.

Each pair of zones shares a COM terminal.

The following diagram illustrates the various possible zone connections:

Installation Manual

11

NOTES:

For zones defined as EOL, use 2.21 KΩ resistors (supplied).

By default all zones are defined as EOL termination.

The Double End Of Line (DOEL) configuration allows a detector tamper switch, if

violated, to register a tamper condition at the panel without the need for a separate

connection to a designated tamper zone.

Only zones 1-6 can be defined as DEOL. Zones 9-14 are not valid in this

configuration.

Double Zone Wiring

Zone doubling is used to connect two separate zones on one input. Use the following

diagram for appropriate connection. The tamper alarm will be the same for both of the

zones.

3.32K 2.21K 5.62K

Tamper

N.C.

Alarm

N.C.

Tamper

N.C.

Alarm

N.C.

Zone No.1 Zone No.9

To Panel

Zone

Input

3.32K 2.21K 5.62K

Tamper

N.C.

Alarm

N.C.

Tamper

N.C.

Alarm

N.C.

Zone No.1 Zone No.9

To Panel

Zone

Input

For double zone wiring use the supplied resistors.

NOTES:

The location of the resistors is crucial. Any change in the resistors' location will adversely affect

the correct zone identification. Zones 1-6 must be applied with the 3.32KΩ resistor. Zones 9-14

must be applied with the 2.21 KΩ and 5.62 KΩ resistors.

Zones 7 and 8 cannot be defined as double zone termination.

Installation Manual

12

Wiring Auxiliary Devices

Use the Auxiliary Power AUX (+) COM (-) terminals to power PIRs, glass-break

detectors (4-wire types), smoke detectors, audio switches, photoelectric systems

and/or any device that requires a 12V DC power supply.

NOTES:

The total power from the AUX terminals should not exceed 600mA.

To connect a 4-wire smoke detector or devices that require resetting after an alarm condition,

connect the Auxiliary power AUX and UO terminals (refer to page 8 for smoke detector wiring).

Remember to define the UO as Switched Auxiliary (refer to page 31).

In addition, when connecting a 4-wire smoke detector observe the wiring guidelines of the local

requirements applicable to smoke detectors.

To prevent a possible drop in voltage due to current requirements and distances involved,

make sure to use the appropriate wire gauge.

If the auxiliary outputs are overloaded (exceed 600mA) and are shut down, you must

disconnect all loads from the outputs for a period of at least 10 seconds before you reconnect

any load to the auxiliary outputs.

Bell Tamper

The bell tamper is a tamper input that is terminated by an EOL resistor (2.21 KΩ). If

the line is cut or shorted, the alarm is turned on.

Connect the bell tamper to the BELL TMP and COM terminals on the main panel.

Box Tamper

The box tamper is a tamper input (NC - normally closed) for the metal box, which

protects both sides of the box. This means that if the box is opened or removed from

the wall, the tamper opens and turns on the alarm.

Connect the box tamper to the BOX TMP and COM terminals on the main panel.

NOTE:

For Bell and Box tamper supervision, connect the tamper switches before applying the main

power to the system.

Installation Manual

13

Utility Output Connections

The ORBIT-14 main panel includes three Utility Outputs on board: 1 relay 3Amps, 1

500mA transistor and 1 open collector 70 mA transistor which can be used for

switching an external device on or off or reset a “latched” smoke detector(s). Once

the Utility Output (UO) is activated the device will be connected between AUX (+12V)

and ground (0V).

Wiring the external Utility Outputs:

UO1: Refer to the J4 connector instructions, described below.

UO2-UO6: Connect the positive connection of the device to AUX (+) and the negative

connection to the UO's (-) terminals.

NOTES:

When activated the Utility Output is switched to the Negative Polarity.

When the UO is used to reset a “latched” smoke detector(s), the 12V power to the smoke

detector is supplied via the UO (see page 8). The UO should be defined as AUX switch (see

page 31).

Connecting the Utility Output Expansion Module

If more than three UOs are required, a Utility Output Expansion module is available.

The UOs on the expansion module comprise four relays; three relays that allow

maximum current of 500 MA each, and one relay that allows maximum current of 3A.

When the Utility Output Expansion Module is employed, UO3 on the Main Board (the

UO3/ECL terminal) is no longer available. UO1 on the Utility Output expansion

module becomes UO3 in the system.

To connect the Utility Output expansion module, connect the terminals as follows:

Panel BUS TERMINALS

UO Expansion

Module terminals

AUX

RED

COM

BLK

ECL

YEL

DAT

GRN

ORBIT-14 Main BUS AUX

RED

COM

BLK

UO3

ECL

DAT

GRN

NOTE:

In order to use the Utility Output Expansion, you have to define the utility module in location 059

(see page 38)

Installation Manual

14

Connecting the J4 Connector

The J4 connector (jumper) determines the UO1 connection (behaviour), which is

normally used for an external siren connection, as follows:

• Positive (POS): When the J4

connector is placed on POS, the

C terminal on UO1 receives

13.8V.

• Negative (NEG): When the J4

connector is placed on NEG, the

C terminal on UO1 receives

COM.

• Single pin: If the J4 connector is

placed only on 1 pin, the UO1

acts as a dry contact.

Page is loading ...

Rokonet ORBiT-14 Installation guide

Rokonet ORBiT-14 Installation guide

Related papers

Other documents