Knick Stratos 2201 pH User manual

Instruction Manual

Stratos 2201 (X) pH

Stratos 2211 (X) pH with

HARTr Communication

Software Version: 3.x

TA-194.100-KNE03 150101

Elektronische Meßgeräte

GmbH & Co.

Beuckestr. 22, D–14163 Berlin

Postfach 37 04 15, D–14134 Berlin

Phone: +49-30-801 91-0

Fax: +49-30-801 91-200

Internet: http://www.knick.de

E-mail: [email protected]

Warranty

Defects occurring within 3 years from delivery date shall

be remedied free of charge at our plant (carriage and

insurance paid by sender).

Accessories: 1 year

Note

Changes 3

Changes for software release 3

Temperature probe adjustment

The Stratos can be adjusted to a connected temperature probe.

This is particularly useful for Pt 100 temperature probes.

(See Pg. 32)

This function should only be used by experts. Incorrectly set parameters may go unnoticed,

but change the measuring properties.

Changes 4

Warning

Information 5

Safety Precautions

Be sure to read and observe the following requirements!

Never use the Stratos 2201/2211 pH for measurement in areas that are subject to an explo-

sion hazard during operation.

Be sure that the supply voltage does not exceed 30 Vdc.

Stratos 2201/2211 X pH is approved for operation in hazardous locations.

Before connecting the Transmitter to a power supply unit, make sure that this is an associ-

ated apparatus.

Whenever it is likely that the protection has been impaired, the instrument shall be made inoperative and

secured against unintended operation.

The protection is likely to be impaired if, for example:

❏the instrument shows visible damage

❏the instrument fails to perform the intended measurements

❏after prolonged storage at temperatures above 70 °C

❏after severe transport stresses

Before recommissioning the instrument, a professional routine test in accordance with EN 61010-1 must be

performed. This test should be carried out at our factory.

The instrument shall not be used in a manner not specified by this manual.

cal

Note

Warning

conf

cal

Information 6

Information on this Instruction Manual

ITALICS are used for texts which appear in the Stratos 2201/2211 (X) pH display.

Bold print is used to represent keys, e.g. cal.

Keys for which the functions are explained are frequently shown in the

left-hand column.

Notes provide important information that should be strictly followed when using the unit.

Warning means that the instructions given must always be followed for your own safety.

Failure to follow these instructions may result in injuries.

Mode Codes

After pressing conf or cal you can enter one of the following codes to access the desig-

nated mode:

conf, 0000: Error info

conf, 1200: Configuration

conf, 5555: Current source

cal, 0000: Cal info

cal, 1015: Temperature probe adjustment

cal, 1100: Calibration

cal, 2222: Test mode (electrode potential display)

Contents 7

Contents

Safety Precautions 5. . . . . . . . . . . . . . . . . . . . . .

Information on this Instruction Manual 6. . .

Mode Codes 6. . . . . . . . . . . . . . . . . . . . . . . . . . . .

1 Assembly 8. . . . . . . . . . . . . . . . . . . . . . . . . . .

Package Contents and Unpacking 8. . . .

Assembly 8. . . . . . . . . . . . . . . . . . . . . . . . . .

2 Installation, Connection

and Commissioning 12. . . . . . . . . . . . . . . . .

Proper Use 12. . . . . . . . . . . . . . . . . . . . . . . .

Overview of the Stratos 12. . . . . . . . . . . . . .

Terminal Assignment 13. . . . . . . . . . . . . . . .

Installation and Commissioning 13. . . . . . .

Wiring Diagrams (pH) 14. . . . . . . . . . . . . . .

Wiring Diagrams (ORP) 19. . . . . . . . . . . . .

3 Operation 20. . . . . . . . . . . . . . . . . . . . . . . . . . .

User Interface 20. . . . . . . . . . . . . . . . . . . . . .

Display 21. . . . . . . . . . . . . . . . . . . . . . . . . . . .

Keypad 21. . . . . . . . . . . . . . . . . . . . . . . . . . . .

Safety Functions 22. . . . . . . . . . . . . . . . . . . .

Outputs 23. . . . . . . . . . . . . . . . . . . . . . . . . . .

Configuration 24. . . . . . . . . . . . . . . . . . . . . . .

Calibration 26. . . . . . . . . . . . . . . . . . . . . . . . .

Measurement 33. . . . . . . . . . . . . . . . . . . . . .

4 Diagnostics, Maintenance and Cleaning 34

Sensoface, Sensocheck34. . . . . . . . . .

Error Messages 35. . . . . . . . . . . . . . . . . . . .

Calibration Error Messages 37. . . . . . . . . .

Diagnostics Functions 38. . . . . . . . . . . . . . .

Maintenance and Cleaning 39. . . . . . . . . . .

5 Annex 40. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Product Line 40. . . . . . . . . . . . . . . . . . . . . . .

Specifications 41. . . . . . . . . . . . . . . . . . . . . .

Certificate of Conformity 44. . . . . . . . . . . . .

Buffer Charts 47. . . . . . . . . . . . . . . . . . . . . . .

Technical Terms 49. . . . . . . . . . . . . . . . . . . . . . . . .

Index 51. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Assembly 8

1 Assembly

Package Contents and Unpacking

Unpack the instrument carefully and check the ship-

ment for transport damage and completeness.

The package contains:

–Front unit of Stratos 2201/2211 (X) pH

–Lower case

–Short instruction sheet

–This instruction manual

–Bag containing:

➀2 sealing plugs ➆1 hinge pin

➁5 hexagon nuts ➇3 cable ties

➂3 Pg cable glands ➈3 filler plugs

➃1 rubber reducer ➉3 gaskets

➄1 Pg plug 11 1 washer

➅4 enclosure screws 12 1 jumper

Assembly

Fig. 1 Assembling the case

➀

(For sealing in case

of wall mounting)

➁

➂

➃

➄

➅

➆

(Can be inserted

from either side)

➇

➈

➉

11

For conduit mounting:

Place washer

between enclosure

and nut.

11

12

Assembly 9

80 [3.15]

32 [1.26]

72 [2.83]

6.2 [0.24] approx. 14

84 [3.31]

42 [1.65] Pg 13.5 (3 pcs.)

144 [5.67]

21

43 [1.69]

105 [4.13] 27

(not included in supply)

Control panel 1 – 22 mm

max. 25 78 [3.07] 27

Control panel cutout

138 x 138 mm (DIN 43700)

Panel-mount kit

consisting of:

4 screws

4 span pieces

4 threaded sleeves

1 seal

➀

➁

➂

➃

➀

➁

➂

Holes for

post mounting

Holes for

wall mounting

(4 x)

(2 x)

For Pg 13.5 threaded cable glands

(use only plastic glands)

[0.55]

[1.06]

[0.83]

[0.98] [1.06]

[5.43 x 5.43]

[0.04 – 0.87]

Note: All dimensions

in mm [inches]

Fig. 2 Dimension drawing for Stratos, mounting diagram and ZU 0275 panel-mount kit

Assembly 10

horizontal post/

40–60 mm dia.

➀

➁

➂

ZU 0276 protective hood

(if required)

For vertical or

pipe mounting

Pipe-mount kit

consisting of:

4 self-tapping screws

1 post mounting plate

2 hose clamps with

➀

➁

➂worm gear drive

to DIN 3017

[1.57–2.36]

Fig. 3 ZU 0274 pipe-mount kit

165 [6.5]

173 [6.81]

132 [5.2]

Fig. 4 ZU 0276 protective hood for wall and pipe mounting

Assembly 11

280 [11.03] 7 [0.28]

➀Recommended stripping lengths for

multi-core cables

➁Recommended stripping length for

coaxial cable

➂Pulling out the terminals using a

screwdriver (also see ➆)

➃Cable laying in the Stratos

➄Connecting lines for loop current

➅Cover for electrode and temperature

probe terminals

➆Areas for placing the screwdriver to

pull out the terminals

➇Connection of handheld terminal

➀➁

➃

➄

Be sure not to

notch the cable

cores when stripping

the insulation!

Dimensions in mm [inches].

➄

➅

➆

➇

Coaxial cable

13 mm [0.5]

7 mm [0.28]

➂

Fig. 5 Installation information Stratos 2201/2211 (X) pH

Warning

Capabilities, Connection 12

2 Installation, Connection and Commissioning

Proper Use

Stratos 2201/2211 (X) pH is used for pH and temper-

ature measurement in industry, the environment,

food processing and waste-water field. It can be

either field-mounted or fixed into a control panel.

Never use the Stratos

2201/2211 pH for measurement in

areas that are subject to an explo-

sion hazard during operation.

Stratos 2201/2211 X pH is ap-

proved for operation in hazardous

locations.

Overview of the Stratos

pH / mV

Sensocheck

Temperature

Pt 100/1000/

NTC 30 kW

Stratos 2201/2211 (X) pH

mA

➀

➁

➂

➃

Fig. 6 System functions of Stratos 2201/2211 (X) pH

➀Inputs for glass and reference electrode

➁Input for temperature probe

➂Current loop 4 – 20 mA,

transports power to and output signal from the

Stratos,

with Stratos 2211 (X) pH also for HARTr commu-

nication

④Equipotential bonding (only with Stratos

2201/2211 X pH)

Warning

Capabilities, Connection 13

Terminal Assignment

+11 10

4 to 20 mA+

–

glass el.

9 8 7 6 5 4 2 1

í

output input

shield

–

aux el.

n.c.

HART

observe grounding conditions

reference el.

Fig. 7 Terminal assignment of Stratos 2201/2211 (X) pH

Installation and Commissioning

Installation and commissioning of

the Stratos may only be carried out

in accordance with this instruction

manual and per applicable local

and national codes. Be sure to ob-

serve the technical specifications

and input ratings.

Before connecting the Stratos

2201/2211 pH to a power supply

unit, make sure that this is not ca-

pable of outputting more than

30 Vdc.

Do not use alternating current or

mains power supply!

Stratos 2201/2211 X pH may only

be connected to an explosion-proof

power supply unit (for input ratings

refer to annex of Certificate of Con-

formity).

When commissioning, a complete

configuration must be carried out.

For easier installation, the terminal strips are of a

plug-in design. The terminals are suitable for single

wires and flexible leads up to 2.5 mm2 (AWG 14)

(see Pg. 11).

See Pg. 14 and following for connection examples.

Do not use cable clamp (shield) for

reference electrode connection

when auxiliary electrode (solution

ground) is in use.

Capabilities, Connection 14

Wiring Diagrams (pH)

reference el.

glass el. +

í

shield

aux. el.

8 7 4 2 1

54 21

5

Temperature

probe Combination

electrode

Fit jumper between

terminals 4 + 5.

Fig. 8a pH measurement with combination electrode and temperature probe,

Sensochecklimited to the glass electrode only

54 21

í

Temperature

probe Combination

electrode

shield

Fit jumper between

terminals 4 + 5.

reference el.

glass el. +

í

aux. el.

8 7 4 2 1

5

Fig. 8b pH measurement with combination electrode and temperature probe,

Sensochecklimited to the glass electrode only

Capabilities, Connection 15

Combination

electrode

shield

54 21

Specify temperature!

Fit jumper between

terminals 4 + 5.

reference el.

glass el. +

í

aux. el.

8 7 4 2 1

5

Fig. 9 pH measurement with combination electrode without temperature probe,

Sensocheck limited to the glass electrode only

Capabilities, Connection 16

54 21

í

shield

reference el.

glass el. +

í

aux. el.

8 5 4 2 1

7

Temperature

probe Glass

electrode

Reference

electrode

Fit jumper between

terminals 4 + 5.

Fig. 10 pH measurement with separate glass and reference electrode and temperature probe,

Sensocheck limited to the glass electrode only

54 21

shield

reference el.

glass el. +

í

aux. el.

8 5 4 2 1

7

Glass

electrode

Reference

electrode

Specify

temperature!

Fit jumper between

terminals 4 + 5.

Fig. 11 pH measurement with separate glass and reference electrode without temperature probe,

Sensocheck limited to the glass electrode only

Capabilities, Connection 17

reference el.

glass el. +

í

shield

aux. el.

8 5 4 2 1

54 21

7

Temperature

probe Combination

electrode

Aux.

electrode

Insulate!

Fig. 12 pH measurement with combination and aux. electrode and temperature probe,

Sensocheck for glass and reference electrode

reference el.

glass el. +

í

shield

aux. el.

8 5 4 2 1

54 21

7

Combination

electrode

Aux.

electrode

Specify

temperature!

Insulate!

Fig. 13 pH measurement with combination and aux. electrode without temperature probe,

Sensocheck for glass and reference electrode

Capabilities, Connection 18

54 21

í

shield

reference el.

glass el. +

í

aux. el.

8 5 4 2 1

7

Temperature

probe Glass

electrode

Reference

electrode

Aux.

electrode

Fig. 14 pH measurement with separate glass, reference and aux. electrode and temperature probe,

Sensocheck for glass and reference electrode

54 21

shield

reference el.

glass el. +

í

aux. el.

8 5 4 2 1

7

Glass

electrode

Reference

electrode

Aux.

electrode

Specify

temperature!

Fig. 15 pH measurement with separate glass, reference and aux. electrode without temperature probe,

Sensocheck for glass and reference electrode

Capabilities, Connection 19

Wiring Diagrams (ORP)

54 21

í

shield

reference el.

glass el. +

í

aux. el.

8 7 4 2 1

5

Insulate!

Temperature

probe combination

ORP electrode

Fig. 16 ORP measurement with separate combination ORP electrode and temperature probe

54 21

shield

reference el.

glass el. +

í

aux. el.

8 7 4 2 1

5

Insulate!

combination

ORP electrode

Specify

temperature!

Fig. 17 ORP measurement with combination ORP electrode without temperature probe

Operation 20

3 Operation

User Interface

meas cal conf

Stratos

cal conf Y"enter

Alarm LED

Keypad

Instrument designation

Rating plate

Status fields:

- Measuring mode

- Calibration mode

- Alarm (Contact only

for Model 2401)

-Wash contact active

(only Model 2401 pH)

- Configuration mode

Fig. 18 Front view of Stratos

Page is loading ...

Knick Stratos 2201 pH User manual

This manual is also suitable for

Knick Stratos 2201 pH User manual

Related papers

Other documents