YOODA 1711190 Quick start guide

Brand: YOODA

Model: 1711190

Category: Remote controls

Type: Quick start guide

In order to fully explore available functions of Universal self-copying remote control please take a moment and read this manual before using the device.

UNIVERSAL SELF-COPYING REMOTE CONTROL

www.sukcesgroup.pl

4-channel universal self-copying remote control

1. Work frequency:

280 – 868 MHz

2. Battery:

CR2032

3. Power:

3 V

4. Signal strength:

to 10 mW

5. Dimensions:

38,5 x 65,5 x 14 mm

6. Range:

up to 100 m in an open area

Radio receiver range is a variable value and can differ from declared values depending on conditions in which device operates.

Possible sources of changes in range are building construction, interference caused by other radio transmitters etc.

1. General information

2. Detailed description

4-channel transmitter

(front)

When replacing the battery, pay attention to the correct polarity. Batteries contain substances that may be hazardous to

health and may pollute the environment. Used batteries should be disposed of properly.

button 2

LED diode

button 4

button 1

button 3

3. Copying remote controls

4. Copying remote control with simple code

5. Copying the remote control with a simple rolling code

Press and hold 3 button, while

holding, press the button 2

three times.

Press the selected button on the

self-copying remote control, under

which you want to copied button of

the original remote control.

The blue LED diode will illuminate

continuously for 2 seconds. The

programming procedure has been

successfully completed. Repeat

the above procedure to copy

further buttons.

We release both buttons,

the red LED diode flashes

every 2 seconds.

The remote control with a simple

code has been copied.

Get closer original remote control

and the self-copying remote

control at a distance

of about 5cm.

Press and hold button on the

original remote control untill blue

LED diode on the self-copying

remote control will flash fast.

Press and hold 3 button,

while holding, press the button 2

three times.

The blue LED diode will illuminate

continuously for 2 seconds. Repeat

the above procedure to copy further

buttons.

After copying, the remote control

must be programmed to the

receiver. We can do it in 2 ways:

1) We use the device's instructions

when programming the remote

control.

2) We use the procedure of quickly

adding a remote control.

To do this, press and hold the copied button for about

10 seconds, until the blue LED diode flashes, then wait

until the LED diode goes out.

We release both buttons,

the red LED diode flashes every

2 seconds.

The remote control with

a simple rolling code

has been copied.

The remote control with

a simple rolling code

has been copied.

Get closer original remote control

and the self-copying remote

control at a distance of

about 5cm.

Press and hold button on the

original remote control untill blue

LED diode on the self-copying

remote control will flash fast.

Press the selected button on the

self-copying remote control,

under which you want to copied

button of the original remote

control.

Code types of copied pilots:

SC (Simple Code) – after copying the code, the remote control works immediately.

RCS (Rolling Code Simple) – rolling code simple.

RCC (Rolling Code Complex) – rolling code composed of the source code.

Remotes with RCS and RCC code after copying require programming to the receiver.

Attention! In a situation where the gate system is secured by the administrator before the next transmitter is added (eg at

the garage door of the housing cooperative), the remote control will not work.

5 cm

6. Copying the remote control with the complex rolling code

7. Copying duplications

Press and hold 3 button,

while holding, press the button 2

three times.

We check in the manual of the

original remote control how it send

the source code. In most remote

controls it is simultaneous pressing

of 1 and 2 buttons.

After sending the source code,

the blue LED diode will flash.

We press the selected button on the

self-copying remote control, under which

the button of the original remote control

will be copied.

We release both buttons,

the red LED diode flashes

every 2 seconds.

Get closer original remote control and

the self-copying remote control at

a distance of about 5cm.

Press and hold button on the

original remote control untill red

LED diode will lights up.

Press and hold 3 button, while

holding, press the button 2

three times.

We release both buttons,

the red LED diode flashes

every 2 seconds.

Get closer original remote control

and the self-copying remote control

at a distance of about 5cm.

Press and hold the button on the

remote control you want to copy.

The rest of the procedure

depends on the type of code

stored in the source remote

control (fixed, simple rolling ,

complex rolling) and we carry

it out as described above.

When the red LED diode flashes every

2 seconds, please send the source

code of the original SEED CODE.

The blue LED diode will illuminate

continuously for 2 seconds.

Repeat the above procedure

to copy further buttons.

The remote control with the complex

rolling code has been copied.

The remote control with the complex

rolling code has been copied.

5 cm

After copying, the remote control

must be programmed to the

receiver. We can do it in 2 ways:

1) We use the device's instructions

when programming the remote

control.

2) We use the procedure of quickly

adding a remote control.

To do this, press and hold the copied button for about

10 seconds, until the blue LED diode flashes, then wait

until the LED diode goes out.

8. Deleting memory from self-copying remote control

9. A list of compatible pilots

Press and hold 3 button,

while holding, press the button 2

three times.

We release both buttons,

the red LED diode flashes

every 2 seconds.

Press the button on the

carbonless remote control

to be removed.

Remote control

has been deleted.

brand

ACM

COMPACT, HY-DOM, MERCURI B, MERCURI C,

SABUTON, MARS, SATURN, ST3/N, TERRA,

TMP-1, TMP-2, UNITECH

BROWN, BROWN RED, BRO.OVER, PASS,

MINIPASS, TECH3

TE4433H BLUE, 433-HG BRAVO

TX2, TX2 COLOR, TX4

TR, TM4, TXM

PTX4 BLU, PTX4 PINK

104251, 104250, 104250 OLD, 104250 RED,

104257, 104350, 654250

FM400, FM400E

TO.GO.WV, TWV, ROLLKEY, APPLE, LOT WVC,

CUPIDO, TO.GO.QV

MITTO, MITTO M, MITTO RCB, MITTO A, TRC,

GHIBLI, MURALE, KLEIO

TRQ S449, XRADO, TRQ S449 GREEN

(PRECODE), TXQ S449, TXQ S449 GREEN,

TRQ S486, TXQ S486, S437 TX

JA33 AMIGO

GENIUS / CASALI A252RC

T432, T434, TOP434A, TOP432, TOP432NA,

TOP434NA, TOP432M, TOP434M, TAM432SA,

TOP432SA, TWIN2, TWIN4, TOP432S

GO, GO PRO, GO MINI

4020-TX03-434, TX02-434-2, TX02-868-2

RCS

RCC

RCS

ADYX

AERF

ALLMATIC

APERIO

APERTO SOMMER

APRIMATIC

ATA

AVIDSEN

BALLAN

BENINCA

BFT

CARDIN

CASALI

CAME

model code

LIFT MASTER / MOTOR LIFT /

CHAMBERLAIN

CLEMSA MUTANCODE, T, T-8, E-CODE N

MASTERCODE MV

ZERO RC

BIXLP, GOL4, BIXLG

TRANSMITTER 4

MILENY, MILENY-EVO

RSC, RSE, RSZ

IRIS, ROLLER 2, ROLLER 433, ROLLER 868,

SOL433, SOL868, VEGA 433, VEGA 868

TML 433 SLH, DL 868 SLH, XT 868 SLH,

XT 433 SLH, T 868 SLH, T 433 SLH,

XT 868 SLH BLACK, XT 433 SLH BLACK

XT 433 RC, TE433HG, XT4 433 RCBE

JUBI-SMALL, JUBI 433

GITR-3, GIT, GICT390, GIFT390-1, G3T-BX,

G1T-BX, GM3T, GICTD, GIFTD

AMIGOLD, AMIGO, KLIO

BRAVO, ECHO

AU1600, AU1600 WOOD, AU1680,

AU1680 WOOD, DOMINO

HSM2, HSM4, HSE2 868

NEO, TWIN

GO, GO PORTIS, GO NORTON

ETH-TEL01

900TXB-42R, TXB 44R, SUB 44R

KUA, KUA E, KUA S

CLIPPER, STYLO

PUNTO 278, GOLDR, GENIE R 273, GENIE

R-GT2N, MIO TR, GT2M, TRN

CLEMSA

DASPI

DEA SYSTEM

DITEC

DOORHAN

DOORMATIC

ECOSTAR

ERREKA

FAAC

FADINI

GENIE

GENIUS

GIBIDI

HORMANN

JCM

KBLUE

KEY

KING GATES

KLING

LABEL SPYCO

FIDO

E945M, E943M, E940M

C940, C945, C943, M842, M844

TX3, TX4, GTX4

SMILO, FLOR-S, VERY-VR, FLOR-S ERA

MCT-11, ACT-21, ACT-22,

STING RAY ACT

LIFE

LINEAR

MERLIN 2.0

MERLIN / PROLIFT

MHOUSE

NICF

RCS

RCC

953ESTD, 971LM, 84330E, 94334CE, 94333E,

94334E, 94335E, 9747E, 1A5639-7, 1A5477,

1A6487, 132B2372, 94330EML, 94333EML,

94335EML, 84330EML, 84333EML,

84335EML, 8747EML

NICE ONE (ON), ON ERA, INTI, ERGO,

PLANO, ONE (ON FM)

TX, T.COM R4-2, T.COM R8-2,

TWIN, TX (NEO)

MTE, MPSTLE, MPSTP2E, TCE, BFOR,

TRQ-P, SLIM-E

GO NORTON, GO MINI NORTON

MCHS, MICRO-NOVOTRON 502,

MINI-NOVOTRON 504, MICRO-NOVOTRON 504,

MICRO-NOWOTRON 31, MICRO-NOVOTRON 51,

MINI-NOVOTRON 30, MINI-NOVOTRON 50,

MNHS

NEO, TXCD

TX MENBRANA

TX 312

LITHIO

NEO

GO ROPER, GO MINI ROPER

BROOVER, BROSTAR

BE HAPPY RS

NEO

MHz 2007, QUARZ SAW

CVXNL, MITTO

SIM433

ALARMA

K-EASY, K-EASY NEW, K-EASY OLD,

MITTO, KEY GO RTS, TELIS RTS,

KEYTIS RTS, KEYTIS RTS NS

4010, 4011, 4014 TX03-434-2,

4013 TX03-434-4, 4020 TX03-868-4,

4026 TX03-868-2, 4022 TX02-434-2, 4025

TX02-868-2, 4031 TX08-868-4

MHz 2007, QUARZ SAW

HEAD, SMART DUAL ROLL, SMART-3 ROLLING

CODE, COCCINELLA

TWIN, VARIO, VARIO MARS,

VARIO OCEAN, NEO

SC RCC

RCC

RCS

NORTON

NOVOFERM

O&O

PECCININ

PRASTEL

RIB

ROPER

ROLOGREC

SABUTOM

SAMMAN

SEA

SEAV

SECULUX

SILVELOX

SEAV

SECULUX

SILVELOX

SIMINOR

SOMFY

SOMMER

PROTECO

PUJOL

(możliwy spersonalizowany kod

bez możliwości skopiowania)

KALLISTO, VENUS AV223 RCS

RCS

RCC

STAGNOLI

250K-SLIMRP, 250K-SLIMR, 250T-4RP

FM400E, FM400

TORMIT4

TSC, TXC, TRC, HANDY, PHOENIX, PHOX 433

ECO-R, TRQ P

RCC

TAU

TELCOMA

TOR LIFT

VDS

YOODA 1711190 Quick start guide

Brand: YOODA

Model: 1711190

Category: Remote controls

Type: Quick start guide

Download PDF

report

YOODA 1711190 Quick start guide

YOODA 1711190 Quick start guide

Other documents