Brother DCP 8060 User manual

Category
Multifunctionals
Type
User manual

This manual is also suitable for

Confidential
FACSIMILE EQUIPMENT
SERVICE MANUAL
MODELS: MFC-8460N/8860DN/8870DW
DCP-8060/8065DN
Confidential
© Copyright Brother 2006
All rights reserved.
No part of this publication may be reproduced in any
form or by any means without permission in writing
from the publisher.
Specifications are subject to change without notice.
i Confidential
PREFACE
This Service Manual is intended for use by service personnel and details the specifications,
construction, theory of operation, and maintenance for the Brother machines noted on the front
cover. It includes information required for troubleshooting and service--disassembly, reassembly,
and lubrication--so that service personnel will be able to understand equipment function, repair the
equipment in a timely manner and order spare parts as necessary.
To perform appropriate maintenance so that the machine is always in the best possible condition
for the customer, service personnel must adequately understand and apply this manual.
HOW THIS MANUAL IS ORGANIZED
This manual is made up of nine chapters and appendices.
CHAPTER 1 PARTS NAMES AND FUNCTIONS
Contains external views and names of components and describes their functions. Information
about the keys on the control panel is included to help you check operation or make adjustments.
CHAPTER 2 SPECIFICATIONS
Lists the specifications of each model, which enables you to make a comparison of different
models.
CHAPTER 3 THEORY OF OPERATION
Gives an overview of the scanning and printing mechanisms as well as the sensors, actuators, and
control electronics. It aids in understanding the basic principles of operation as well as locating
defects for troubleshooting.
CHAPTER 4 TRANSFER OF DATA LEFT IN THE MACHINE TO BE SENT FOR REPAIR
Describes how to transfer data left in the machine to be sent for repair. The service personnel
should instruct end users to follow the transfer procedure given in this chapter if the machine at the
user site cannot print received data due to the printing mechanism defective. End users can
transfer received data to another machine to prevent data loss.
CHAPTER 5 DISASSEMBLY/REASSEMBLY AND LUBRICATION
Details procedures for disassembling and reassembling the machine together with related notes.
The disassembly order flow provided enables you to see at a glance the quickest way to get to
component(s) involved.
At the start of a disassembly job, you check a disassembly order flow that guides you through a
shortcut to the object components.
This chapter also covers screw tightening torques and lubrication points to which the specified
lubricants should be applied during reassembly jobs.
CHAPTER 6 ADJUSTMENTS AND UPDATING OF SETTINGS REQUIRED AFTER PARTS
REPLACEMENT
Details adjustments and updating of settings, which are required if the head/carriage unit, main
PCB and some other parts have been replaced.
CHAPTER 7 CLEANING
Provides cleaning procedures not covered by the User's Manual. Before starting any repair work,
clean the machine as it may solve the problem concerned.
ii Confidential
CHAPTER 8 MAINTENANCE MODE
Describes the maintenance mode which is exclusively designed for the purpose of checks, settings
and adjustments using the keys on the control panel.
In the maintenance mode, you can update memory (EEPROM: electrically erasable programmable
read-only memory) contents for optimizing the drive conditions of the head/carriage unit, paper
feed roller or paper ejection roller (if they have been replaced) or for setting the CCD scanner area,
for example. You can also customize the EEPROM according to the shipment destination of the
machine concerned. In addition, you can perform operational checks of the LCD, control panel
PCB or sensors, perform a print test, display the log information or error codes, and modify
firmware switches (WSW).
CHAPTER 9 ERROR INDICATION AND TROUBLESHOOTING
Details error messages and codes that the incorporated self-diagnostic functions display if any
error or malfunction occurs. If any error message appears, refer to this chapter to find which
components should be checked or replaced.
The latter half of this chapter provides sample problems that could occur in the main sections of
the machine and related troubleshooting procedures. This will help service personnel pinpoint and
repair defective components.
APPENDIX 1 SERIAL NUMBERING SYSTEM
Shows the location of serial number labels put on some parts and lists the coding information
pertaining to the serial numbers.
APPENDIX 2 FIRMWARE INSTALLATION
Provides instructions on how to update firmware stored in the flash ROM on the main PCB or load
firmware to a new main PCB from the host PC.
No hardware replacement is required for updating.
APPENDIX 3 CUSTOMIZING CODES ACCORDING TO SHIPPING DESTINATION
Lists the customizing codes for the various preferences exclusively designed for each destination
(e.g. language). Those codes are stored in the memory (EEPROM) mounted on the main PCB. If
the main PCB is replaced with a new one, therefore, you will need to set the proper customizing
codes with the machine in the maintenance mode.
APPENDIX 4 FIRMWARE SWITCHES (WSW)
Describes the functions of the firmware switches, which can be divided into two groups: one is for
customizing preferences designed for the shipping destination (as described in Appendix 3) and
the other is for modifying preferences that match the machine to the environmental conditions.
Use the latter group if the machine malfunctions due to mismatching.
APPENDIX 5 WIRING DIAGRAM
Provides the wiring diagram that helps you understand the connections between PCBs.
APPENDIX 6 CIRCUIT DIAGRAMS
Provides the circuit diagrams of the NCU PCB and power supply PCB.
APPENDIX 7 VIEWING THE EVENT LOG FILE
When installing the printer driver, the installer logs events that occur during the installation
process in the event log file. This appendix views a sample of the event log file. Selecting Start |
Program | Brother | MFL-Pro Suite model name | Installation Diagnostics reads out the event log
file.
This manual describes the models and their versions destined for major countries.
The specifications and functions are subject to change depending upon each destination.
iii Confidential
TABLE OF CONTENTS
CHAPTER 1 PARTS NAMES & FUNCTIONS
1.1 EQUIPMENT OUTLINE.............................................................................................1-1
1.2 CONTROL PANEL ....................................................................................................1-2
1.3 COMPONENTS ......................................................................................................... 1-7
CHAPTER 2 SPECIFICATIONS
2.1 GENERAL.................................................................................................................. 2-1
2.1.1 General Specifications .........................................................................................2-1
2.1.2 Paper Specifications.............................................................................................2-2
2.1.2.1 Paper handling ...............................................................................................2-2
2.1.2.2 Media specifications .......................................................................................2-2
2.1.3 Printable Area ................................................................................................................2-5
2.1.3.1 PCL5e/EPSON/IBM emulation .......................................................................2-5
2.1.3.2 PCLXL, PS (BR-Script 3)................................................................................2-8
2.1.4 Print Speeds with Various Settings ............................................................................. 2-9
2.1.5 Toner Cartridge Weight Information .........................................................................2-10
2.2 SPECIFICATIONS LIST ..........................................................................................2-11
CHAPTER 3 THEORY OF OPERATION
3.1 OVERVIEW................................................................................................................3-1
3.2 MECHANICAL COMPONENTS ................................................................................3-2
3.2.1 Scanner Mechanism ............................................................................................3-3
3.2.2 Overview of Gear .................................................................................................3-9
3.2.3 Paper Transfer ...................................................................................................3-10
3.2.3.1 Paper supply .............................................................................................. 3-10
3.2.3.2 Paper registration.......................................................................................3-12
3.2.3.3 Drum unit....................................................................................................3-12
3.2.3.4 Developing .................................................................................................3-13
3.2.3.5 Fixing stage................................................................................................3-14
3.2.3.6 Paper eject .................................................................................................3-15
3.2.3.7 Duplex printing (For the models with the DX only).....................................3-16
iv Confidential
3.2.3.8 Paper feeding from the MP tray .................................................................3-17
3.2.3.9 LT tray ........................................................................................................3-17
3.2.4 Toner Cartridge ..................................................................................................3-18
3.2.4.1 Toner life end mode ...................................................................................3-18
3.2.4.2 New toner detection mechanism................................................................3-20
3.2.4.3 Counter reset during indication of “Toner Life End” ................................... 3-21
3.2.5 Print Process ...................................................................................................... 3-22
3.2.5.1 Charging..................................................................................................... 3-22
3.2.5.2 Exposure stage ..........................................................................................3-22
3.2.5.3 Transfer......................................................................................................3-23
3.2.6 Sensors .............................................................................................................. 3-24
3.3 CONTROL ELECTRONICS .................................................................................... 3-25
3.3.1 Components .......................................................................................................3-25
CHAPTER 4 TRANSFER OF DATA LEFT IN THE MACHINE TO BE SENT FOR REPAIR
4.1 TRANSFERRING RECEIVED FAX DATA ................................................................4-1
CHAPTER 5 DISASSEMBLY/REASSEMBLY AND LUBRICATION
5.1 DISASSEMBLY/REASSEMBLY ...............................................................................5-1
Safety Precautions............................................................................................................5-1
Tightening Torque ............................................................................................................5-2
Harness Routing...............................................................................................................5-4
Preparation .....................................................................................................................5-21
How to Access the Object Component...........................................................................5-21
Disassembly Flowchart...................................................................................................5-22
5.1.1 AC Cord..............................................................................................................5-23
5.1.2 Drum/Toner ASSY..............................................................................................5-23
5.1.3 DX Feed ASSY (For the models with the DX only) ............................................5-24
5.1.4 Paper Tray.......................................................................................................... 5-24
5.1.5 Back Cover.........................................................................................................5-27
5.1.6 DX Blank Cover (For models with out the DX only) ...........................................5-27
5.1.7 Outer Chute ASSY .............................................................................................5-28
v Confidential
5.1.8 Access Cover/Side Cover L ...............................................................................5-30
5.1.9 ADF Unit............................................................................................................. 5-31
5.1.10 Hinge Base R .....................................................................................................5-32
5.1.11 Hinge Arm R.......................................................................................................5-33
5.1.12 Hinge ASSY L.....................................................................................................5-33
5.1.13 ADF Cover ASSY ...............................................................................................5-34
5.1.14 ADF Side Cover F ..............................................................................................5-34
5.1.15 ADF Side Cover R..............................................................................................5-35
5.1.16 ADF Chute ASSY ...............................................................................................5-36
5.1.17 SB Chute ASSY (For the models with the DX only) /
SX Chute (For the models with out the DX only) ...............................................5-38
5.1.18 Exit Chute Cover ASSY......................................................................................5-38
5.1.19 Earth Spring .......................................................................................................5-39
5.1.20 PF Roller Holder ASSY ......................................................................................5-40
5.1.21 LF Roller 1 ASSY ...............................................................................................5-41
5.1.22 SB Roller ASSY (For the models with the DX only) ...........................................5-42
5.1.23 ADF Motor ..........................................................................................................5-44
5.1.24 SB Solenoid ASSY (For the models with the DX only).......................................5-45
5.1.25 PF Solenoid ASSY (For the models with the DX only).......................................5-45
5.1.26 ADF Relay PCB..................................................................................................5-46
5.1.27 Paper Feed Chute ASSY ...................................................................................5-47
5.1.28 Actuator Front 1/Photo Interrupter
(For the models with the DX only)......................................................................5-48
5.1.29 Actuator Front 2/Photo Interrupter
(For the models with the DX only)......................................................................5-49
5.1.30 ADF Film/Spring Plate ADF Front A ASSY/Separation Rubber/Rubber Holder/
Separation Spring...............................................................................................5-50
5.1.31 Pressure Roller/LF Spring .................................................................................. 5-50
5.1.32 LF Roller 2 ASSY ...............................................................................................5-51
5.1.33 Exit Roller ASSY.................................................................................................5-52
5.1.34 LF Roller 3 ASSY ...............................................................................................5-53
5.1.35 LF Roller 4 ASSY ...............................................................................................5-54
5.1.36 Flap A ASSY (For the models with the DX only)/
Flap A (For models with out the DX only)...........................................................5-55
vi Confidential
5.1.37 Document Hold/Document Hold Spring .............................................................5-56
5.1.38 Upper Main Chute ASSY/Lower Main Chute ASSY...........................................5-56
5.1.39 Actuator R/Photo Interrupter ..............................................................................5-58
5.1.40 Flap B .................................................................................................................5-59
5.1.41 Actuator SB/Photo Interrupter (For the models with the DX only)...................... 5-59
5.1.42 Document Ejection Tray.....................................................................................5-60
5.1.43 Document Cover Sensor.................................................................................... 5-61
5.1.44 Eject Roller B4....................................................................................................5-61
5.1.45 Presser Roller.....................................................................................................5-62
5.1.46 Panel Cover ASSY ............................................................................................. 5-63
5.1.47 Scanner Unit ASSY ............................................................................................5-64
5.1.48 Top Cover ASSY ................................................................................................5-65
5.1.49 Lock Lever B/Lock Lever ASSY .........................................................................5-65
5.1.50 CCD Module.......................................................................................................5-66
5.1.51 FFC Cable ASSY ...............................................................................................5-68
5.1.52 Scanner Motor FB .............................................................................................. 5-69
5.1.53 Pulley ASSY .......................................................................................................5-70
5.1.54 Photo Interrupter ................................................................................................5-70
5.1.55 Panel Unit...........................................................................................................5-71
5.1.56 Panel PCB ASSY ...............................................................................................5-72
5.1.57 Printed Rubber Key ............................................................................................5-73
5.1.58 LCD Cover/Backlight Module/LCD .....................................................................5-74
5.1.59 NCU PCB ASSY (For the models with the NCU only) .......................................5-75
5.1.60 Speaker ASSY ...................................................................................................5-77
5.1.61 Driver PCB .........................................................................................................5-78
5.1.62 Fuser Unit...........................................................................................................5-79
5.1.63 Tray MP ASSY ...................................................................................................5-81
5.1.64 MP Tray Cover ASSY/Process Cover ASSY......................................................5-82
5.1.65 Main PCB ...........................................................................................................5-85
5.1.66 Gear Plate Calking ASSY AL/Develop Joint/Main Motor ASSY AL....................5-86
5.1.67 Main Shield Plate ASSY.....................................................................................5-88
vii Confidential
5.1.68 Relay Rear PCB ASSY/Connector .....................................................................5-90
5.1.69 Relay Front PCB ASSY ......................................................................................5-92
5.1.70 MP Solenoid ASSY.............................................................................................5-93
5.1.71 Drive Release Link .............................................................................................5-94
5.1.72 T1 Solenoid ASSY..............................................................................................5-95
5.1.73 Toner Sensor PCB .............................................................................................5-95
5.1.74 Register Solenoid ASSY.....................................................................................5-96
5.1.75 Ejector Solenoid ASSY (For the models with the DX only) ................................5-96
5.1.76 Interlock SW ASSY ............................................................................................5-97
5.1.77 New Toner Actuator ...........................................................................................5-97
5.1.78 Gear 17/20 .........................................................................................................5-98
5.1.79 Thermistor ASSY..............................................................................................5-100
5.1.80 Side Cover R ....................................................................................................5-100
5.1.81 Joint Cover ASSY.............................................................................................5-101
5.1.82 Filter ................................................................................................................. 5-102
5.1.83 Laser Unit .........................................................................................................5-103
5.1.84 PS PCB Unit.....................................................................................................5-104
5.1.85 High-Voltage PS PCB ASSY............................................................................5-107
5.1.86 Toner LED PCB Unit ASSY..............................................................................5-109
5.1.87 Fan Motor 60 Unit.............................................................................................5-110
5.1.88 Fan Motor 60 Unit LV ....................................................................................... 5-110
5.1.89 Frame L ............................................................................................................ 5-111
5.1.90 Frame R ...........................................................................................................5-111
5.1.91 MP Unit.............................................................................................................5-112
5.1.92 Regist Actuator Rear/Regist Actuator Spring ...................................................5-117
5.1.93 Regist Actuator Front/Regist Actuator Spring ..................................................5-119
5.1.94 Roller Holder ASSY.......................................................................................... 5-120
5.1.95 PE Actuator, Edge Actuator, Edge Actuator Spring .........................................5-121
5.1.96 PE PG Sensor ASSY .......................................................................................5-123
5.1.97 Wireless PCB (PCB T60H929.00 ASSY 02) (For the model with the Wireless only)5-124
5.2 DISASSEMBLY/REASSEMBLY (LT-5300) ..........................................................5-125
5.2.1 Paper Tray........................................................................................................ 5-125
viii Confidential
5.2.2 LT Front Cover ASSY.......................................................................................5-128
5.2.3 LT Rear Cover..................................................................................................5-129
5.2.4 LT Side Cover L ...............................................................................................5-129
5.2.5 LT Side Cover R...............................................................................................5-130
5.2.6 LT PCB ASSY ..................................................................................................5-131
5.2.7 Connector: 55533-1219....................................................................................5-132
5.2.8 Connector: 54702-1219....................................................................................5-132
5.2.9 Gear 24 LT ....................................................................................................... 5-133
5.2.10 Collar 6 .............................................................................................................5-134
5.2.11 LT Solenoid ASSY............................................................................................5-138
5.2.12 Roller Holder ASSY.......................................................................................... 5-139
5.2.13 Edge Actuator Spring .......................................................................................5-140
5.2.14 PE Actuator, Edge Actuator .............................................................................5-141
5.2.15 LT Sensor PCB ASSY......................................................................................5-142
5.3 LUBRICATION ......................................................................................................5-144
CHAPTER 6 ADJUSTMENTS AND UPDATING OF SETTINGS, REQUIRED AFTER PARTS
REPLACEMENT
6.1 IF YOU REPLACE THE MAIN PCB..........................................................................6-1
6.1.1 Load Update Programs/data ................................................................................6-1
6.1.2 Initialize the EEPROM on the Main PCB (Function code 01)...............................6-1
6.1.3 Customize the EEPROM on the Main PCB (Function code 74)........................... 6-1
6.1.4 Check the Control Panel PCB for Normal Operation (Function code 13) ............6-1
6.1.5 Make a Sensor Operation Check (Function code 32) ..........................................6-1
6.1.6 Acquire of White Level Data and Set the CCD Scanner Area
(Function code 55) .................................................................................................6-1
6.1.7 Setting the Serial Number ....................................................................................6-1
6.1.8 Switch Back to Standby........................................................................................6-2
6.2 IF YOU REPLACE THE DOCUMENT SCANNER UNIT...........................................6-2
6.2.1 Acquire of White Level Data and Set the CCD Scanner Area
(Function code 55) ...............................................................................................6-2
6.3 IF YOU REPLACE THE DRUM UNIT .......................................................................6-2
6.4 PERIODICAL REPLACEMENT PARTS ...................................................................6-3
6.4.1 Periodical Replacement Parts ..............................................................................6-3
ix Confidential
6.4.2 Procedures to Replace Periodical Replacement Parts ........................................ 6-4
6.4.2.1 Fuser unit and laser unit...............................................................................6-4
6.4.2.2 Paper feeding kit for tray 1, 2.....................................................................6-32
6.4.2.3 Paper feeding kit for MP tray......................................................................6-39
CHAPTER 7 CLEANING
CHAPTER 8 MAINTENANCE MODE
8.1 ENTRY INTO THE MAINTENANCE MODE .............................................................8-1
8.2 LIST OF MAINTENANCE-MODE FUNCTIONS .......................................................8-2
8.3 USER-ACCESS TO THE MAINTENANCE MODE ...................................................8-3
8.4 DETAILED DESCRIPTION OF MAINTENANCE-MODE FUNCTIONS.................... 8-4
8.4.1 EEPROM Parameter Initialization (Function code 01/91) ....................................8-4
8.4.2 Printout of Scanning Compensation Data (Function code 05) .............................8-5
8.4.3 Placement of CCD Unit in Position for Transportation (Function code 06)..........8-9
8.4.4 ADF Performance Test (Function code 08) .........................................................8-9
8.4.5 Test Pattern 1 (Function code 09)......................................................................8-10
8.4.6 Firmware Switch Setting and Printout ................................................................8-11
8.4.6.1 Firmware switch setting (Function code 10) ..............................................8-11
8.4.6.2 Printout of firmware switch data (Function code 11)..................................8-13
8.4.7 Operation Check of LCD (Function code 12) .....................................................8-14
8.4.8 Operational Check of Control Panel PCB (Function code 13) ...........................8-15
8.4.9 Sensor Operational Check (Function code 32) ..................................................8-16
8.4.10 Received Data Transfer Function (Function code 53)
(Not applicable to DCP-8060/8065DN.).............................................................8-18
8.4.11 Fine Adjustment of Scan Start/End Positions (Function code 54) .....................8-20
8.4.12 Acquisition of White Level Data and CCD Scanner Area Setting
(Function code 55) .............................................................................................8-22
8.4.13 Paper Feeding and Ejecting Test (Function code 67)........................................ 8-23
8.4.14 EEPROM Customizing (Function code 74) ........................................................ 8-23
8.4.15 Display of the Equipment’s Log Information (Function code 80)........................8-24
8.4.16 Machine Error Code Indication (Function code 82)............................................8-26
8.4.17 Output of Transmission Log to the Telephone Line (Function code 87)
(Not applicable to DCP-8060/8065DN.).............................................................8-26
x Confidential
8.4.18 Counter Reset After Replacing the Fuser Unit, Laser Unit and
Paper Feed Kit (Function code 88)....................................................................8-27
8.4.19 Cancellation of the Memory Security Mode
(Not applicable to with out the NCU models and the Japanese model.) ...........8-27
CHAPTER 9 ERROR INDICATION AND TROUBLESHOOTING
9.1 ERROR INDICATION ................................................................................................9-1
9.1.1 Equipment Errors .................................................................................................9-1
9.1.1.1 Error messages appearing on the LCD..........................................................9-1
9.1.1.2 Error codes shown in "MACHINE ERROR X X" messages ...........................9-4
9.1.2 Communications Errors......................................................................................9-11
9.2 TROUBLESHOOTING ............................................................................................9-15
9.2.1 Introduction.........................................................................................................9-15
9.2.2 Precautions ........................................................................................................9-15
9.2.3 Checking Prior to Troubleshooting.....................................................................9-15
9.2.4 Troubleshooting Based on Problem Type.......................................................... 9-16
9.2.4.1 Paper feeding problems ...............................................................................9-16
9.2.4.2 Software setting problems............................................................................ 9-18
9.2.4.3 Malfunction ...................................................................................................9-21
9.2.4.4 Image defects............................................................................................... 9-27
9.2.4.5 Incorrect printout...........................................................................................9-47
9.2.4.6 Network problem ..........................................................................................9-49
9.2.4.7 Troubleshooting of the control panel ............................................................9-56
9.2.4.8 Troubleshooting of fax functions ..................................................................9-58
APPENDIX 1 SERIAL NUMBERING SYSTEM
APPENDIX 2 FIRMWARE INSTALLATION
A2.1 INSTALLING THE UPDATE DATA TO THE MACHINE..................................APP. 2-1
A2.2 SETTING ID CODES TO MACHINES..............................................................APP. 2-7
APPENDIX 3 CUSTOMIZING CODES ACCORDING TO SHIPPING DESTINATION
xi Confidential
APPENDIX 4 FIRMWARE SWITCHES (WSW)
APPENDIX 5 WIRING DIAGRAM
APPENDIX 6 CIRCUIT DIAGRAMS
NCU PCB
POWER SUPPLY PCB 100V
POWER SUPPLY PCB 200V
APPENDIX 7 VIEWING THE EVENT LOG FILE
APPENDIX 8 READMARKS
Confidential
xii
SAFETY PRECAUTIONS
To use the machine safely
Please keep these instructions for later reference and read them before attempting any maintenance.
NOTE: If there are faxes in the machine's memory, you need to print them or save them before you
turn off the power and unplug the machine.
WARNING
There are high voltage electrodes inside the machine.
Before you clean the inside of the machine, make sure
you have unplugged the telephone line cord first and
then the power cord from the AC power outlet.
Do not handle the plug with wet hands.
Doing this might cause an electrical shock.
After you use the machine, some
internal parts are extremely HOT!
To prevent injuries, be careful not to
put your fingers in the areas shown
in the illustration.
The fuser unit is marked with a caution label.
Please do not remove or damage the label.
To prevent injuries, be careful not to put your
hands on the edge of the machine under the
scanner cover.
To prevent injuries, be careful not to
put your fingers in the area shown in
the illustrations.
Do not use a vacuum cleaner to clean up scattered toner. Doing this might cause the toner dust to
ignite inside the vacuum cleaner, potentially starting a fire. Please carefully clean the toner dust with
a dry, lint-free cloth and dispose of it according to local regulations.
Confidential
xiii
WARNING
- When you move the machine, grasp the side hand holds that are under the scanner. DO NOT
carry the machine by holding it at the bottom.
- Use caution when installing or modifying telephone lines. Never touch telephone wires or
jack. Never install telephone wiring during a lightning storm. Never install a telephone wall
jack in a wet location.
- This product must be installed near an AC power outlet that is easily accessible. In case of
an emergency, you must disconnect the power cord from the AC power outlet to shut off the
power completely.
- To reduce the risk of shock or fire, use only a No. 26 AWG or larger telecommunication line
cord.
CAUTION
Lightning and power surges can damage this product! We recommend that you use a quality
surge protection device on the AC power line and on the telephone line, or unplug the cords
during a lightning storm.
WARNING
IMPORTANT SAFETY INSTRUCTIONS
When using your telephone equipment, basic safety precautions should always be followed to
reduce the risk of fire, electric shock and injury to people, including the following:
1. Do not use this product near water, for example, near a bath tub, wash bowl, kitchen sink or
washing machine, in a wet basement or near a swimming pool.
2. Avoid using this product during an electrical storm. There may be a remote risk of electric
shock from lightning.
3. Do not use this product to report a gas leak in the vicinity of the leak.
4. Use only the power cord provided with the MACHINE.
SAVE THESE INSTRUCTIONS
Confidential
xiv
CHOOSING A LOCATION
Place your machine on a flat, stable surface that is free of vibration and shocks, such as a desk.
Put the machine near a telephone wall jack and a standard, grounded AC power outlet.
Choose a location where the temperature remains between 50°F and 90.5°F (10°C and 32.5°C).
CAUTION
- Avoid placing your machine in a high-traffic area.
- Do not place the machine near heaters, air conditioners, water, chemicals, or refrigerators.
- Do not expose the machine to direct sunlight, excessive heat, moisture, or dust.
- Do not connect your machine to an AC power outlet controlled by wall switches or automatic
timers.
- Disruption of power can wipe out information in the machine’s memory.
- Do not connect your machine to an AC power outlet on the same circuit as large appliances or
other equipment that might disrupt the power supply.
- Avoid interference sources, such as speakers or the base units of cordless phones.
Confidential
CHAPTER 1
PARTS NAMES & FUNCTIONS
Confidential
CHAPTER 1 PARTS NAMES & FUNCTIONS
This chapter contains external views and names of components and describes their functions.
Information about the keys on the control panel is included to help you check operation or make
adjustments.
CONTENTS
1.1 EQUIPMENT OUTLINE ...................................................................................................1-1
1.2 CONTROL PANEL...........................................................................................................1-2
1.3 COMPONENTS................................................................................................................1-7
1-1 Confidential
1.1 EQUIPMENT OUTLINE
Front view
Fig. 1-1
Rear view
Fig. 1-2
ADF Document Output Support Flap
Document Cover
Power Switch
Front Cover
Paper Tray
Control Panel
USB Interface Connector
Parallel Interface Connector
10/100 Baser TX Port
AC Power Connector
Back Cover
Automatic Document Feeder (ADF)
Face-down Output Tray
Support Flap with Extension
(Support Flap)
1-2 Confidential
1.2 CONTROL PANEL
MFC-8460N, MFC-8860DN and MFC-8870DW have similar control keys.
Fig. 1-3
1. One-Touch Keys 5. Dial pad Keys
These 20 keys give you instant access to 40
previously stored numbers.
Shift
Lets you access One-Touch numbers 21 to 40 when
held down.
Used to enter telephone and fax numbers or to
enter text.
The [#] key temporarily switches the dialing mode
from Pulse to Tone during a telephone call.
2. Status LED 6. Stop/Exit Key
The LED will flash and change color depending on
the machine status.
Stops an operation or exits from a menu.
3. LCD 7. Start Key
Displays messages to help you use your machine.
4. Menu Keys
Menu
Accesses the main menu.
Clear/Back
Deletes entered data or lets you exit the menu.
OK
Selects a setting.
or
Scrolls backwards or forwards through menu
selections.
Changes the volume when in fax or standby mode.
or
Scrolls through the menus and options.
Starts sending a fax, making a copy or scanning.
7
3 4 5 6 2 1
8 9 10 11
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140
  • Page 141 141
  • Page 142 142
  • Page 143 143
  • Page 144 144
  • Page 145 145
  • Page 146 146
  • Page 147 147
  • Page 148 148
  • Page 149 149
  • Page 150 150
  • Page 151 151
  • Page 152 152
  • Page 153 153
  • Page 154 154
  • Page 155 155
  • Page 156 156
  • Page 157 157
  • Page 158 158
  • Page 159 159
  • Page 160 160
  • Page 161 161
  • Page 162 162
  • Page 163 163
  • Page 164 164
  • Page 165 165
  • Page 166 166
  • Page 167 167
  • Page 168 168
  • Page 169 169
  • Page 170 170
  • Page 171 171
  • Page 172 172
  • Page 173 173
  • Page 174 174
  • Page 175 175
  • Page 176 176
  • Page 177 177
  • Page 178 178
  • Page 179 179
  • Page 180 180
  • Page 181 181
  • Page 182 182
  • Page 183 183
  • Page 184 184
  • Page 185 185
  • Page 186 186
  • Page 187 187
  • Page 188 188
  • Page 189 189
  • Page 190 190
  • Page 191 191
  • Page 192 192
  • Page 193 193
  • Page 194 194
  • Page 195 195
  • Page 196 196
  • Page 197 197
  • Page 198 198
  • Page 199 199
  • Page 200 200
  • Page 201 201
  • Page 202 202
  • Page 203 203
  • Page 204 204
  • Page 205 205
  • Page 206 206
  • Page 207 207
  • Page 208 208
  • Page 209 209
  • Page 210 210
  • Page 211 211
  • Page 212 212
  • Page 213 213
  • Page 214 214
  • Page 215 215
  • Page 216 216
  • Page 217 217
  • Page 218 218
  • Page 219 219
  • Page 220 220
  • Page 221 221
  • Page 222 222
  • Page 223 223
  • Page 224 224
  • Page 225 225
  • Page 226 226
  • Page 227 227
  • Page 228 228
  • Page 229 229
  • Page 230 230
  • Page 231 231
  • Page 232 232
  • Page 233 233
  • Page 234 234
  • Page 235 235
  • Page 236 236
  • Page 237 237
  • Page 238 238
  • Page 239 239
  • Page 240 240
  • Page 241 241
  • Page 242 242
  • Page 243 243
  • Page 244 244
  • Page 245 245
  • Page 246 246
  • Page 247 247
  • Page 248 248
  • Page 249 249
  • Page 250 250
  • Page 251 251
  • Page 252 252
  • Page 253 253
  • Page 254 254
  • Page 255 255
  • Page 256 256
  • Page 257 257
  • Page 258 258
  • Page 259 259
  • Page 260 260
  • Page 261 261
  • Page 262 262
  • Page 263 263
  • Page 264 264
  • Page 265 265
  • Page 266 266
  • Page 267 267
  • Page 268 268
  • Page 269 269
  • Page 270 270
  • Page 271 271
  • Page 272 272
  • Page 273 273
  • Page 274 274
  • Page 275 275
  • Page 276 276
  • Page 277 277
  • Page 278 278
  • Page 279 279
  • Page 280 280
  • Page 281 281
  • Page 282 282
  • Page 283 283
  • Page 284 284
  • Page 285 285
  • Page 286 286
  • Page 287 287
  • Page 288 288
  • Page 289 289
  • Page 290 290
  • Page 291 291
  • Page 292 292
  • Page 293 293
  • Page 294 294
  • Page 295 295
  • Page 296 296
  • Page 297 297
  • Page 298 298
  • Page 299 299
  • Page 300 300
  • Page 301 301
  • Page 302 302
  • Page 303 303
  • Page 304 304
  • Page 305 305
  • Page 306 306
  • Page 307 307
  • Page 308 308
  • Page 309 309
  • Page 310 310
  • Page 311 311
  • Page 312 312
  • Page 313 313
  • Page 314 314
  • Page 315 315
  • Page 316 316
  • Page 317 317
  • Page 318 318
  • Page 319 319
  • Page 320 320
  • Page 321 321
  • Page 322 322
  • Page 323 323
  • Page 324 324
  • Page 325 325
  • Page 326 326
  • Page 327 327
  • Page 328 328
  • Page 329 329
  • Page 330 330
  • Page 331 331
  • Page 332 332
  • Page 333 333
  • Page 334 334
  • Page 335 335
  • Page 336 336
  • Page 337 337
  • Page 338 338
  • Page 339 339
  • Page 340 340
  • Page 341 341
  • Page 342 342
  • Page 343 343
  • Page 344 344
  • Page 345 345
  • Page 346 346
  • Page 347 347
  • Page 348 348
  • Page 349 349
  • Page 350 350
  • Page 351 351
  • Page 352 352
  • Page 353 353
  • Page 354 354
  • Page 355 355
  • Page 356 356
  • Page 357 357
  • Page 358 358
  • Page 359 359
  • Page 360 360
  • Page 361 361
  • Page 362 362
  • Page 363 363
  • Page 364 364
  • Page 365 365
  • Page 366 366
  • Page 367 367
  • Page 368 368
  • Page 369 369
  • Page 370 370
  • Page 371 371
  • Page 372 372
  • Page 373 373
  • Page 374 374
  • Page 375 375
  • Page 376 376
  • Page 377 377
  • Page 378 378
  • Page 379 379
  • Page 380 380
  • Page 381 381
  • Page 382 382
  • Page 383 383
  • Page 384 384
  • Page 385 385
  • Page 386 386
  • Page 387 387
  • Page 388 388
  • Page 389 389
  • Page 390 390
  • Page 391 391
  • Page 392 392
  • Page 393 393
  • Page 394 394
  • Page 395 395
  • Page 396 396
  • Page 397 397
  • Page 398 398
  • Page 399 399
  • Page 400 400
  • Page 401 401
  • Page 402 402
  • Page 403 403
  • Page 404 404
  • Page 405 405
  • Page 406 406
  • Page 407 407
  • Page 408 408
  • Page 409 409
  • Page 410 410
  • Page 411 411
  • Page 412 412
  • Page 413 413
  • Page 414 414
  • Page 415 415
  • Page 416 416
  • Page 417 417
  • Page 418 418
  • Page 419 419
  • Page 420 420
  • Page 421 421
  • Page 422 422
  • Page 423 423
  • Page 424 424
  • Page 425 425
  • Page 426 426
  • Page 427 427
  • Page 428 428
  • Page 429 429
  • Page 430 430
  • Page 431 431
  • Page 432 432
  • Page 433 433
  • Page 434 434
  • Page 435 435
  • Page 436 436
  • Page 437 437
  • Page 438 438
  • Page 439 439
  • Page 440 440
  • Page 441 441
  • Page 442 442
  • Page 443 443
  • Page 444 444
  • Page 445 445
  • Page 446 446
  • Page 447 447
  • Page 448 448
  • Page 449 449
  • Page 450 450
  • Page 451 451
  • Page 452 452
  • Page 453 453
  • Page 454 454
  • Page 455 455
  • Page 456 456
  • Page 457 457
  • Page 458 458
  • Page 459 459
  • Page 460 460
  • Page 461 461
  • Page 462 462
  • Page 463 463
  • Page 464 464
  • Page 465 465
  • Page 466 466
  • Page 467 467
  • Page 468 468
  • Page 469 469
  • Page 470 470
  • Page 471 471
  • Page 472 472
  • Page 473 473
  • Page 474 474
  • Page 475 475
  • Page 476 476
  • Page 477 477
  • Page 478 478
  • Page 479 479
  • Page 480 480
  • Page 481 481
  • Page 482 482
  • Page 483 483
  • Page 484 484
  • Page 485 485
  • Page 486 486
  • Page 487 487

Brother DCP 8060 User manual

Category
Multifunctionals
Type
User manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI