Manufactured for: Dynarex Corporation
10 Glenshaw Street | Orangeburg, NY 10962
USA • www.dynarex.com | Made in China
WARNINGS/CAUTIONS
WEIGHT CAPACITY: 1000 LB.
IMPORTANT: DO NOT use this equipment without
reading and understanding these instructions first. If you
are unable to understand the warnings, cautions, and
instructions, please contact your distributor or Dynarex
representative.
• Ensure you have been properly trained by your doctor
or physical therapist before using crutches.
• Ensure that rubber crutch tips are not ripped, worn, or
missing. Replace before using the crutches.
• Use extra caution on wet and slippery surfaces.
• The crutches have a recommended weight limit of
1000 lb./pair.
INSTALLATION PRECAUTIONS
• Proper height adjustments MUST be made to both the
leg extensions and the hand grips.
• A dealer or therapist should examine the placement of
the crutches before use to ensure optimal balance and
support.
• Be sure that snap buttons are fully protruding through
the same respective adjustment hole of each leg
extension. This ensures that the adjustable legs are
securely locked into position and that an even height
adjustment is obtained.
• Wing nuts MUST be tight at ALL times.
HEIGHT ADJUSTMENT
1. Unlock both blue euro-style clips on Hand Grip by
using thumbs and pressing outward on thumb tab.
2. With both thumbs, push Hand Grip down in order to
have full access to brass push pins.
3. Height Adjustments Details
For Individuals Between 4’7” and 5’2”
Set underarm adjustment tube in first (lowest from
ground) set of INSIDE adjustment holes on the top
crutch section, making sure push pins protrude all the
way through the adjustment hole.
For Individuals Between 5'3" and 5'10”
Turn crutch upside down so underarm pad is on the
floor. With foot, hold underarm pad to the floor and pull
up on receptacle tube while depressing push pins. Set
underarm adjustment tube in the second (middle) set of
INSIDE adjustment holes on the top crutch section.
Make sure push pins protrude all the way through the
adjustment holes.
For Individuals Between 5’11” and 6’7”
Turn crutch upside down so underarm pad is on the
floor. With foot, hold underarm pad to the floor and pull
up on receptacle tube while depressing push pins. Set
underarm adjustment tube in the third (highest from
ground) set INSIDE adjustment holes on the top crutch
section. Make sure push pins protrude all the way
through the adjustment holes.
ASSEMBLY INSTRUCTIONS
1. Carefully remove contents from package.
2. With one hand, place bottom section on floor with tip
securely on the ground. Insert top section into tubing
Reorder Nos. 10105
10106
Bariatric Steel Crutches
Adult and Tall Adult
as shown. Depress both brass push pins simultaneously
with thumbs and slide top half into bottom half until the
push pins “pop” through holes. You will hear an audible
click when top section is secure.
4. Adjust bottom height adjustment tube by depressing
both silver push pins and rotating slightly so push pins
flow freely. Slide to desired height and turn until silver
push pins protrude through holes.
5. Set Hand Grip by placing underarm pad under armpit
and sliding Hand Grip so that the elbow has a 10° bend.
6. When correct position is achieved, lock euro-style clips
in place by inserting into positioning hole and locking
push tab.
7. Repeat for second crutch.
ADJUSTING HANDLE POSITION (DETAIL “A”)
1. Remove the wing nut and bolt securing the handle to
the crutch.
2. Align the handle with the desired set of adjustment
holes.
3. Secure with wing nut and bolt.
4. Repeat for second crutch.
ADJUST THE LEG EXTENSION (DETAIL “B”)
1. Depress both snap buttons on the leg extension and
allow them to snap through the desired adjustment
holes on the crutch leg frame.
2. Make sure snap buttons are fully engaged and locked
in place before use.
3. Repeat for second crutch.
DETAIL “B”
Snap Button
Crutch Leg Frame
Adjustment Hole (1 of 9)
Leg Extension
Adjustment Holes (1 of 5)
DETAIL “A”
Bolt
Crutch
Crutch
Handle
Wing
Nut
HEIGHT ADJUSTMENT (CONT’D) SAFETY CHECK
LIMITED LIFETIME WARRANTY
1. Unlock both blue euro-style clips on Hand Grip by
using thumbs and pressing outward on thumb tab.
2. With both thumbs, push Hand Grip down in order to
have full access to brass push pins.
3. Height Adjustments Details
For Individuals Between 4’7” and 5’2”
Set underarm adjustment tube in first (lowest from
ground) set of INSIDE adjustment holes on the top
crutch section, making sure push pins protrude all the
way through the adjustment hole.
For Individuals Between 5'3" and 5'10”
Turn crutch upside down so underarm pad is on the
floor. With foot, hold underarm pad to the floor and pull
up on receptacle tube while depressing push pins. Set
underarm adjustment tube in the second (middle) set of
INSIDE adjustment holes on the top crutch section.
Make sure push pins protrude all the way through the
adjustment holes.
For Individuals Between 5’11” and 6’7”
Turn crutch upside down so underarm pad is on the
floor. With foot, hold underarm pad to the floor and pull
up on receptacle tube while depressing push pins. Set
underarm adjustment tube in the third (highest from
ground) set INSIDE adjustment holes on the top crutch
section. Make sure push pins protrude all the way
through the adjustment holes.
SYMBOL GLOSSARY
For an explanation of symbols
used in Dynarex packaging, visit
dynarex.com/symbols.php R221114
WARNING:
Cancer and Reproductive Harm
www.P65Warnings.ca.gov
Your Dynarex Product is warrantied to be free of defects in
materials and workmanship for the lifetime of the product
for the original purchaser. This item was built to exacting
standards and carefully inspected prior to shipment. This
Limited Lifetime Warranty is an expression of our
confidence in the materials and workmanship of our
products and our assurance to the consumer of years of
dependable service.
The Warranty shall not apply under the following
conditions:
• Problems arising from normal wear
• Problems arising from failure to adhere to the product
instructions
• Problems arising from misuse, negligence, accident or
improper operation, maintenance or storage
• Problems arising from modifications or unauthorized
repairs, parts or attachments
• Products where the serial number has been removed or
defaced
• Problems with non-durable components, such as rubber
accessories, casters, and grips, which are subject to
normal wear and need periodic replacement
Dynarex shall not be liable for any consequential or
incidental damages whatsoever. Dynarex shall repair or
replace defective products at its option. The foregoing
warranty is exclusive and in lieu of other express
warranties, if any, including the implied warranties of
merchantability and fitness of a particular purpose. The
remedy for any violation of the implied warranty shall be
limited to repair or replacement of the defective product
pursuant to the terms contained herein.
If you have a question about your Dynarex device or this
warranty, please contact an authorized Dynarex dealer.
*This product meets or exceeds all federal safety and
environmental regulations.
With crutches positioned per diagram, confirm patient can
lean forward comfortably while resting on the underarm
supports. Patient should not have to stand uncomfortably
erect. Ensure both pushbuttons are firmly in place and
handgrips are secure.
4. Adjust bottom height adjustment tube by depressing
both silver push pins and rotating slightly so push pins
flow freely. Slide to desired height and turn until silver
push pins protrude through holes.
5. Set Hand Grip by placing underarm pad under armpit
and sliding Hand Grip so that the elbow has a 10° bend.
6. When correct position is achieved, lock euro-style clips
in place by inserting into positioning hole and locking
push tab.
7. Repeat for second crutch.
ADJUSTING HANDLE POSITION (DETAIL “A”)
1. Remove the wing nut and bolt securing the handle to
the crutch.
2. Align the handle with the desired set of adjustment
holes.
3. Secure with wing nut and bolt.
4. Repeat for second crutch.
ADJUST THE LEG EXTENSION (DETAIL “B”)
1. Depress both snap buttons on the leg extension and
allow them to snap through the desired adjustment
holes on the crutch leg frame.
2. Make sure snap buttons are fully engaged and locked
in place before use.
3. Repeat for second crutch.
/
