Bretford TVSW12AC User manual
- Type
- User manual
TVSW12AC
CUBE MICRO
WALL CABINET
VER.1 SEPT.2019
1. Product specifications ....................................................................... P.1
2. Components ........................................................................................ P.2
3. Mounting Considerations ................................................................. P.2
4. Setup ..................................................................................................... P.3~6
5. Extra/Optional Solutions .................................................................. P.7~8
6. Safety .................................................................................................... P.9
General Use
The BRETFORD CUBE MICRO WALL CABINET provides compact charging
for up to 12 notebook or tablet devices (up to 13.3 inch).
6. Safety
Always turn off the power to the product before plugging IN or OUT.
Do not unplug the power cord from the outlet when your hands are wet.
Do not use cables that are damaged.
Do not unplug the cable into an extension cable.
This product is designed to be used indoors only.
This product is not designed to be operated by a child or student.
Only adults should operate or move this product.
Do not allow anyone to sit, stand, or climb on the product.
Move the product with caution.
Keep the product away from water.
Keep the ventilation holes unobstructed for air circulation.
Do not use the product to store liquids or cleaning supplies.
Disconnect the power cable from the wall before relocating the main unit.
WARNING:
Ground Wire Setup
!
This product must only be used for its intended purpose in accordance with operating
instructions . Failure to observe the following notices can result it fire, injury, death by
electric shock or equipment damage.
IMPORTANT SAFETY INSTRUCTIONS
When using an electrical mounting system, basic precautions should always be followed,
including the following : Read all instructions before using this product.
DANGER – To reduce the risk of electric shock :
1. Always unplug this product from the electrical outlet before cleaning.
WARNING – To reduce the risk of burns, fire, electric shock, or injury to persons :
2. Unplug from outlet before adding or removing parts.
3. Use this product only for its intended use as described in these instructions.
Do not use attachments not recommended by the manufacturer.
4. Never operate this product if it has a damaged cord or plug. If it is not working
properly, return the mounting system to a service center for examination and repair.
5. Keep the cord away from heated surfaces.
6. Never operate the product with the air opening blocked. Keep the air opening free
of lint, hair, and the like.
7. Never drop or insert any object into any opening on the product.
8. Do not use outdoors.
9. Route cords and cables as shown in the installation instruction.
10. To disconnect, turn all controls to the off position, then remove plug from outlet.
WARNING: Risk of Electric Shock – Connect this product to a properly grounded outlet
only. See Ground Wire Setup.
Warning: Risk of injury to Persons – do not use the mounting system to support any
product other than the CUBE MICRO WALL CABINET.
Class I Equipment. This equipment must be grounded. The power plug must
be connected to a properly wired earth ground socket outlet. An improperly
wired socket outlet could place hazardous voltages on accessible metal parts.
1. Unfasten the screw
first 2. Fasten the screw back
into the ground wire.
9
1
1. Product Specifications
2. Components
Product Specifications
Model Name
Capacity
Cabinet Dimensions
W20.86 x D7.08 x H35.04”
(530 x 180 x 890 mm)
12 Devices (up to 13.3”)
38.14 lb (17.3 kg)
49.2 lb (22.4 kg)
TVSW12AC
Tablets, Chromebooks, laptops
Input: AC 100-125V, 50/60Hz, 12A
AC 200-240V, 50/60Hz, 10A
Output: AC 100-125V, 50/60Hz, 12A
AC 200-240V, 50/60Hz, 10A
Power System
Compatibility
Shipping Weight
8
180mm
7.08”
530mm
20.86”
890mm
35.04” 890mm
35.04”
T4 x L30mm x 5 pcs
32.7mm
2.7mmØ9 30mm
T4
1mm
Washer x 5 pcs
For Conctete
IDØ5.5
ODØ12
Ø11.3 Ø5
19mm
16mm
T5 x L16mm x 5 pcs
Ø3.8
Ø8.8
25.3mm
27.5mm
6.5mm
2.2mm
Nylon Wall Plug x 5 pcs
dimension:Ø 1/4” x Depth 1
Wall Mount Bracket
Power Cord
Power cord holder
x2 pcs
Ground Wire 12 AWG
Keys x 2 pcs
Setup: Connect Unit 1 to Unit 2 with attached daisy chain cable.
Daisy-Chain (P ower)
Min 23.62” (600mm)
Caution: 79 lb (36kg)
Do not exceed maximum listed capacity. Serious injury or property damage may occur.
Weight w/o
Equipment
Concrete Wall:
Accessories:
Wood Stud wall:
Daisy Chain
Power Cord Plastic Ties
x 30 pcs
Unit 1 Unit 2
FRONT SIDE REAR
Power cord holder
x2 pcs
2
3. Mounting Considerations
7
Space Requirements
Remove Packaging and Open The Door to Get User Guide
Thumbscrews
M4 x L12mm
Remove the
screws to open
the left door
Use the key
to open the
door
x 2
Wooden wall needs to be at least 0.98” / 25 mm in thickness.
!
1. Remove the four screws from the top and bottom of the power strip.
2. Move power
strip to alternate
position.
3. Reattach screws to
secure the power
strip.
Mo vableP ower Strip
The power strip can be repositioned to accommodate a wider variety of power adapters.
5. Extra / Optional Solutions
23.62” / 600mm (Operation Space)
37.40” / 950mm (Operation Space)
35.04” / 890mm (Cabinet Space)
Operation Space
Cabinet Space
20.86” / 530mm (Cabinet Space)
5.9” / 150mm
7.64” / 194mm 11.81” / 300mm
1.42” / 36mm
5.9” / 150mm 4.5” / 115mm
4.3”
109mm
28.4” / 721mm
2.36” / 60mm
5 mounting holes
3
4. Setup
6
Metal Wall bracket
T5 X L16mm x 3 pcs
T5 X L16mm x 2 pcs
Mounting to W ooden Wall
Follow the Cabinet Space Requirements
(min. 2 people)
1. Secure to wooden wall with T5 screwdriver.
1.Plug the device power adapters into the outlets inside.
(Customer supplies power adapters that come with the
devices)
2.Route cables through the access holes and clip the cables
as shown in the above pictures.
If the devices come with adapters, fix the adapters to the metal hooks with the attached
ties.
2. Hang cabinet onto the bracket, then tighten the
bottom screws.
Tools Needed
M
FT
Ø
C able Management
A dapter Management
5
4
Install P ower Cord Retention Clip
P ower Cord Retention Clip
Install the bracket
1. Tighten the retention clip on the power cord.
2. Insert the power cord into the C13 Inlet on the
underside of the cabinet.
3. Make sure the clip is facing the wall side.
As you insert the power cord, attach the clip to
the small hole adjacent to the inlet.
Press to release the
power cord
Tighten the power cord
Pull up to release the clip and the
power cord from the cabinet.
Wall
Front door
C13 Inlet
4. Using a Phillips driver, attach the metal bracket
to the wall using the washers and T4 screws.
5. Install the cabinet onto the metal bracket.
Secure the cabinet using the washers and T4 screws into the lower part of cabinet.
Washer x 5pcs Self-tapping Screw X 5pcs
T4 x L30mm
3. Insert the wall plugs into the
holes.
2. Drill holes in the concrete wall about
Ø 1/4” X 1” deep at the mounting points.
Nylon wall plug x 5pcs
Mounting toC oncrete Wall (min. 2 people)
Follow the Cabinet Space Requirements
1. Determine the installation points for your cabinet.
5
4
Install P ower Cord Retention Clip
P ower Cord Retention Clip
Install the bracket
1. Tighten the retention clip on the power cord.
2. Insert the power cord into the C13 Inlet on the
underside of the cabinet.
3. Make sure the clip is facing the wall side.
As you insert the power cord, attach the clip to
the small hole adjacent to the inlet.
Press to release the
power cord
Tighten the power cord
Pull up to release the clip and the
power cord from the cabinet.
Wall
Front door
C13 Inlet
4. Using a Phillips driver, attach the metal bracket
to the wall using the washers and T4 screws.
5. Install the cabinet onto the metal bracket.
Secure the cabinet using the washers and T4 screws into the lower part of cabinet.
Washer x 5pcs Self-tapping Screw X 5pcs
T4 x L30mm
3. Insert the wall plugs into the
holes.
2. Drill holes in the concrete wall about
Ø 1/4” X 1” deep at the mounting points.
Nylon wall plug x 5pcs
Mounting toC oncrete Wall (min. 2 people)
Follow the Cabinet Space Requirements
1. Determine the installation points for your cabinet.
3
4. Setup
6
Metal Wall bracket
T5 X L16mm x 3 pcs
T5 X L16mm x 2 pcs
Mounting to W ooden Wall
Follow the Cabinet Space Requirements
(min. 2 people)
1. Secure to wooden wall with T5 screwdriver.
1.Plug the device power adapters into the outlets inside.
(Customer supplies power adapters that come with the
devices)
2.Route cables through the access holes and clip the cables
as shown in the above pictures.
If the devices come with adapters, fix the adapters to the metal hooks with the attached
ties.
2. Hang cabinet onto the bracket, then tighten the
bottom screws.
Tools Needed
M
FT
Ø
C able Management
A dapter Management
2
3. Mounting Considerations
7
Space Requirements
Remove Packaging and Open The Door to Get User Guide
Thumbscrews
M4 x L12mm
Remove the
screws to open
the left door
Use the key
to open the
door
x 2
Wooden wall needs to be at least 0.98” / 25 mm in thickness.
!
1. Remove the four screws from the top and bottom of the power strip.
2. Move power
strip to alternate
position.
3. Reattach screws to
secure the power
strip.
Mo vableP ower Strip
The power strip can be repositioned to accommodate a wider variety of power adapters.
5. Extra / Optional Solutions
23.62” / 600mm (Operation Space)
37.40” / 950mm (Operation Space)
35.04” / 890mm (Cabinet Space)
Operation Space
Cabinet Space
20.86” / 530mm (Cabinet Space)
5.9” / 150mm
7.64” / 194mm 11.81” / 300mm
1.42” / 36mm
5.9” / 150mm 4.5” / 115mm
4.3”
109mm
28.4” / 721mm
2.36” / 60mm
5 mounting holes
1
1. Product Specifications
2. Components
Product Specifications
Model Name
Capacity
Cabinet Dimensions
W20.86 x D7.08 x H35.04”
(530 x 180 x 890 mm)
12 Devices (up to 13.3”)
38.14 lb (17.3 kg)
49.2 lb (22.4 kg)
TVSW12AC
Tablets, Chromebooks, laptops
Input: AC 100-125V, 50/60Hz, 12A
AC 200-240V, 50/60Hz, 10A
Output: AC 100-125V, 50/60Hz, 12A
AC 200-240V, 50/60Hz, 10A
Power System
Compatibility
Shipping Weight
8
180mm
7.08”
530mm
20.86”
890mm
35.04” 890mm
35.04”
T4 x L30mm x 5 pcs
32.7mm
2.7mmØ9 30mm
T4
1mm
Washer x 5 pcs
For Conctete
IDØ5.5
ODØ12
Ø11.3 Ø5
19mm
16mm
T5 x L16mm x 5 pcs
Ø3.8
Ø8.8
25.3mm
27.5mm
6.5mm
2.2mm
Nylon Wall Plug x 5 pcs
dimension:Ø 1/4” x Depth 1
Wall Mount Bracket
Power Cord
Power cord holder
x2 pcs
Ground Wire 12 AWG
Keys x 2 pcs
Setup: Connect Unit 1 to Unit 2 with attached daisy chain cable.
Daisy-Chain (P ower)
Min 23.62” (600mm)
Caution: 79 lb (36kg)
Do not exceed maximum listed capacity. Serious injury or property damage may occur.
Weight w/o
Equipment
Concrete Wall:
Accessories:
Wood Stud wall:
Daisy Chain
Power Cord Plastic Ties
x 30 pcs
Unit 1 Unit 2
FRONT SIDE REAR
Power cord holder
x2 pcs
1. Product specifications ....................................................................... P.1
2. Components ........................................................................................ P.2
3. Mounting Considerations ................................................................. P.2
4. Setup ..................................................................................................... P.3~6
5. Extra/Optional Solutions .................................................................. P.7~8
6. Safety .................................................................................................... P.9
General Use
The BRETFORD CUBE MICRO WALL CABINET provides compact charging
for up to 12 notebook or tablet devices (up to 13.3 inch).
6. Safety
Always turn off the power to the product before plugging IN or OUT.
Do not unplug the power cord from the outlet when your hands are wet.
Do not use cables that are damaged.
Do not unplug the cable into an extension cable.
This product is designed to be used indoors only.
This product is not designed to be operated by a child or student.
Only adults should operate or move this product.
Do not allow anyone to sit, stand, or climb on the product.
Move the product with caution.
Keep the product away from water.
Keep the ventilation holes unobstructed for air circulation.
Do not use the product to store liquids or cleaning supplies.
Disconnect the power cable from the wall before relocating the main unit.
WARNING:
Ground Wire Setup
!
This product must only be used for its intended purpose in accordance with operating
instructions . Failure to observe the following notices can result it fire, injury, death by
electric shock or equipment damage.
IMPORTANT SAFETY INSTRUCTIONS
When using an electrical mounting system, basic precautions should always be followed,
including the following : Read all instructions before using this product.
DANGER – To reduce the risk of electric shock :
1. Always unplug this product from the electrical outlet before cleaning.
WARNING – To reduce the risk of burns, fire, electric shock, or injury to persons :
2. Unplug from outlet before adding or removing parts.
3. Use this product only for its intended use as described in these instructions.
Do not use attachments not recommended by the manufacturer.
4. Never operate this product if it has a damaged cord or plug. If it is not working
properly, return the mounting system to a service center for examination and repair.
5. Keep the cord away from heated surfaces.
6. Never operate the product with the air opening blocked. Keep the air opening free
of lint, hair, and the like.
7. Never drop or insert any object into any opening on the product.
8. Do not use outdoors.
9. Route cords and cables as shown in the installation instruction.
10. To disconnect, turn all controls to the off position, then remove plug from outlet.
WARNING: Risk of Electric Shock – Connect this product to a properly grounded outlet
only. See Ground Wire Setup.
Warning: Risk of injury to Persons – do not use the mounting system to support any
product other than the CUBE MICRO WALL CABINET.
Class I Equipment. This equipment must be grounded. The power plug must
be connected to a properly wired earth ground socket outlet. An improperly
wired socket outlet could place hazardous voltages on accessible metal parts.
1. Unfasten the screw
first 2. Fasten the screw back
into the ground wire.
9
TVSW12AC
CUBE MICRO
WALL CABINET
VER.1 SEPT.2019
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
