AGI HX10-36 Swing-Away Grain Auger Assembly Manual

Read this manual before using product. Failure to

follow instructions and safety precautions can

result in serious injury, death, or property

damage. Keep manual for future reference.

Part Number: 30549 R2

Revised: May 2022

Original Instructions

MK/HX 10-36

Swing-Away Grain Auger

Assembly & Operator’s Manual

This manual applies to:

Westfield MK10-36, Hutchinson HX10-36, Mayrath HX10-36

This product has been designed and manufactured to meet general engineering standards. Other local

regulations may apply and must be followed by the operator. All personnel must be trained in the correct

operational and safety procedures for this product. Use the sign-off sheet below to record initial and periodic

reviews of this manual with all personnel.

Date Employee Name and Signature Employer Name and Signature

MK/HX 10-36 – SWING-AWAY GRAIN AUGER

30549 R2 3

CONTENTS

1. Introduction ............................................................................................................................................ 4

2. Safety First .............................................................................................................................................. 5

2.1 Safety Alert Symbol and Signal Words...................................................................................... 5

2.2 Operational Safety..................................................................................................................... 5

2.3 Transport and Placement Safety............................................................................................... 8

2.4 Maintenance Safety .................................................................................................................. 9

3. Assembly ............................................................................................................................................... 17

3.1 Arrange Tubes and Apply Model Decals................................................................................. 17

3.2 Tube and Flight Assembly ....................................................................................................... 19

3.3 Trackshoe and Trackstop......................................................................................................... 20

3.4 Boot Assembly......................................................................................................................... 21

3.5 Install the Discharge Spout ..................................................................................................... 22

3.6 Transport Undercarriage Assembly ........................................................................................ 23

3.7 Winch and Lift Cable Installation ............................................................................................ 25

3.8 Winch Handle Assembly.......................................................................................................... 27

3.9 PTO (CV) Driveline Installation................................................................................................ 28

3.10 Standard Intake Hopper Assembly ....................................................................................... 29

3.11 Hopper Lift Arm/Winch Assembly ........................................................................................ 31

3.12 Hitch Jack Installation............................................................................................................ 33

3.13 Auger/Tractor Hook Up......................................................................................................... 33

3.14 Optional Low Profile Hopper Assembly ................................................................................ 36

3.15 Low Profile Hopper Lift Arm Assembly ................................................................................. 38

3.16 Plastic Manual Holder Installation ........................................................................................ 39

4. Transport............................................................................................................................................... 40

4.1 Pre-Transport Checklist ........................................................................................................... 40

4.2 Transport Procedure ............................................................................................................... 42

5. Placement ............................................................................................................................................. 43

5.1 Pre-Placement Procedure ....................................................................................................... 43

5.2 Placement Procedure .............................................................................................................. 44

6. Operation .............................................................................................................................................. 45

6.1 Pre-Operational Checklist........................................................................................................ 45

6.2 Auger Drive and Lockout......................................................................................................... 46

6.3 Start Up and Break In .............................................................................................................. 46

6.4 Full Load Procedures ............................................................................................................... 47

6.5 Normal/Emergency Shutdown................................................................................................ 48

6.6 Completion/Clean-Up.............................................................................................................. 48

6.7 Lowering Procedure ................................................................................................................ 49

7. Maintenance & Storage ....................................................................................................................... 50

7.1 General Maintenance Procedure............................................................................................ 50

7.2 Removable Hopper Mesh Guard............................................................................................. 52

7.3 General Storage Procedure..................................................................................................... 53

4 30549 R2

1. Introduction

Congratulations. As the new owner of an AGI MK/HX Series Grain Auger, you will be working with

equipment especially designed to complement and improve your farming operation. Before using this

auger, we recommend that you read this manual and familiarize yourself with the various features of

the machine and the necessary precautions for an efficient and safe operation.

In addition, we suggest that anyone using this auger be required as a matter of record to be familiar

with all safety precautions. A sign-off form is supplied on the inside front cover to record your safety

reviews.

Thank you.

1. INTRODUCTION MK/HX 10-36 – SWING-AWAY GRAIN AUGER

30549 R2 5

2. Safety First

Safety First. Everyone knows about it. Most people practice it. Sadly, a few choose to ignore it. Safety

should be a habit, something you practice every time you work with machinery. Safe working habits

prevent needless injuries or deaths.

Whether you are the owner, a supervisor, or an operator, it is your responsibility to know the

operational requirements, the safety precautions, and the potential hazards of portable grain augers.

Further more, you must ensure that anyone working with or around the auger, is familiar with them.

Failure to read this manual and/or non-compliance with correct safety procedures is a misuse of the

equipment. Remember, a lack of knowledge serves only to endanger yourself and those around you.

TAKE THE TIME — BE ALERT — BE SAFE.

2.1. Safety Alert Symbol and Signal Words

This safety alert symbol indicates important safety messages in this manual. When you see

this symbol, be alert to the possibility of injury or death, carefully read the message that

follows, and inform others.

Signal Words: Note the use of the signal words DANGER,WARNING,CAUTION, and NOTICE with the safety

messages. The appropriate signal word for each message has been selected using the definitions below as a

guideline.

Indicates an imminently hazardous situation that, if not avoided, will result in serious injury or

death.

Indicates a hazardous situation that, if not avoided, could result in serious injury or death.

Indicates a hazardous situation that, if not avoided, may result in minor or moderate injury.

Indicates a potentially hazardous situation that, if not avoided, may result in property damage.

2.2. Operational Safety

Operational safety means using common sense and knowing and observing proper precautions. Always

remember to:

• Keep children and untrained people away from auger work area (see Figure 1). The area around the auger is

not safe for untrained personnel and especially not safe for children.

• Have another person nearby who can shut down the auger in case of accident. It is good practice to always

work with a second person around augers.

• Inspect the lift cable before using auger. Replace if frayed or damaged.

• Make certain lift cable is properly seated in roller and cable clamps are secure.

• Ensure that the auger is empty before raising or lowering.

• Augers are not insulated. Keep away from all electric lines. Electrocution can occur without direct contact.

• Wear hearing protection when operating auger.

MK/HX 10-36 – SWING-AWAY GRAIN AUGER 2. SAFETY FIRST

6 30549 R2

• Do not operate with any safety shield removed.

•Never use a PTO driveline without a rotating shield in good working order. Also ensure shields on auger

boot and tractor are in place.

•Be certain the PTO driveline is securely attached to the flighting shaft and to the tractor before operating.

• Before starting tractor, be certain that power to the PTO is in the off position.

• Keep body, hair and clothing away from moving parts.

• Operate auger on level ground. Even though the auger is connected to the tractor during operation, tipping

can occur.

• Anchor or support discharge end to further stabilize auger and prevent tipping.

• Keep away from the intake hopper during operation.

• Do not operate auger with the service or cleanout doors open or unlatched.

• Shut off and lock out all power to auger before servicing, cleaning or adjusting.

• Lower auger at completion of operation, or when not in use.

• Do not get on or beneath auger when raising or lowering intake hitch jack, or when auger is supported by

hitch jack.

2. SAFETY FIRST MK/HX 10-36 – SWING-AWAY GRAIN AUGER

30549 R2 7

Figure 1. Work Area

MK/HX 10-36 – SWING-AWAY GRAIN AUGER 2. SAFETY FIRST

8 30549 R2

2.3. Transport and Placement Safety

The approach to transport and placement safety is no different from that of operational safety. Follow the basic

rules of good sense and know the limitations of your machinery. While a few of the precautions are the same,

they bear repeating. Remember to:

• Keep children and unauthorized personnel away from the hazard area

surrounding the auger.

• Transport auger in the full down position with slight tension on the cable.

• Check the lift cable before each use and replace if frayed or damaged.

Also check cable clamps.

• Make certain that the hitch pin is in place and the safety chain is properly

attached. Use a type of hitch pin that will not permit auger to separate

from the tractor.

• Always attach a SMV (Slow Moving Vehicle) sign before transporting

auger.

• Equip the auger with the necessary lights for transportation where

required by law.

• Raise intake feed hopper into transport position and lock hopper lift

winch before transporting or moving auger. Intake feed side of hopper

must face away from main auger when in transport position (see Figure

40).

• Before moving auger, make sure the area around the auger is clear of

obstructions and/or unauthorized personnel. (see Figure 2).

• Use extreme caution in turning and cornering.

• Do not raise or lower auger until hazard area is clear.

• Do not permit anyone to stand on or beneath auger when raising or

lowering.

• Wheels must be free to move when raising or lowering auger.

• Do not use auger as a hoist.

• Before moving auger, check and double check for overhead obstructions

and/or electrical wires. Electrocution can occur without direct contact.

• Do not transport auger faster than 15 mph (24 km/h).

• Do not operate auger with the intake hopper in transport position. This

will cause damage to u-joint.

• Do not transport auger on a slope greater than 20 degrees.

• Disconnect PTO driveline from tractor for transport or placement. Secure

in transport saddle.

Figure 2.

2. SAFETY FIRST MK/HX 10-36 – SWING-AWAY GRAIN AUGER

30549 R2 9

2.4. Maintenance Safety

When performing maintenance on the MK/HX auger, understand and observe the following precautions.

• Shut down and lock out all power before attempting maintenance of any kind. If lock-out is impossible,

disconnect the PTO driveline from tractor.

• Support auger tube before attempting maintenance on the undercarriage. Auger should be in full down

position for maintenance.

• After maintenance is completed, replace and secure all safety shields, safety devices, service doors and

cleanout covers.

• Keep decals clean. Replace any decal that is damaged or not clearly visible.

• Use only genuine AGI replacement parts or equivalent. Replacement parts such as intake shields, pulley

shields, PTO driveline shields, winches and lift cables MUST MEET ASAE Standards or serious injury may

result. Use of unauthorized parts will void warranty. If in doubt, contact AGI or your AGI dealer. Do not

modify any auger components.

Figure 3. Safety Decal Locations

MK/HX 10-36 – SWING-AWAY GRAIN AUGER 2. SAFETY FIRST

10 30549 R2

Figure 4. Safety Decal Locations

Figure 5. Safety Decal Locations

2. SAFETY FIRST MK/HX 10-36 – SWING-AWAY GRAIN AUGER

30549 R2 11

Table 1. Safety Decals

Part Number Description

20813

To prevent death or serious injury:

• KEEP AWAY from rotating auger flighting.

• DO NOT remove or modify auger flighting

guards, doors, or covers. Keep in good working

order. Have replaced if damaged.

• DO NOT operate the auger without all guards,

doors, and covers in place.

• NEVER touch the auger flighting. Use a stick or

other tool to remove an obstruction or clean out.

• Shut off and lock out power to adjust, service, or

clean.

ROTATING FLIGHTING HAZARD

DANGER

20818

DANGER

To prevent serious injury or death:

• Keep body, hair, and clothing away from rotating

PTO driveline.

• Do not operate equipment unless all driveline,

tractor, and equipment shields are in place and in

good working order.

• Make certain the driveline shields turn freely on

driveline.

• Make certain the driveline is securely attached at

both ends.

• Do not exceed specified operating speed (see

operator’s manual).

• Keep u-joint angles small and equal. Do not exceed

maximum recommended length for PTO driveline.

ROTATING PTO DRIVELINE

MK/HX 10-36 – SWING-AWAY GRAIN AUGER 2. SAFETY FIRST

12 30549 R2

Table 1 Safety Decals (continued)

Part Number Description

17094

To prevent serious injury or death, do

not operate auger unless swing-

hopper is securely attached to boot.

ROTATING FLIGHTING INSIDE

DANGER

20816

DANGER

ELECTROCUTION HAZARD

To prevent death or serious injury:

• When operating or moving, keep equipment

away from overhead power lines and devices.

• Fully lower equipment before moving.

This equipment is not insulated.

Electrocution can occur without direct contact.

17113

To prevent serious injury or death:

• Securely attach equipment to vehicle with

correct pin and safety chains.

• Use a tow vehicle to move equipment.

TRANSPORT HAZARD

WARNING

2. SAFETY FIRST MK/HX 10-36 – SWING-AWAY GRAIN AUGER

30549 R2 13

Table 1 Safety Decals (continued)

Part Number Description

201198

To prevent serious injury or death:

• Keep body, hair, and clothing away from rotating

pulleys, belts, chains, and sprockets.

• Do not operate with any guard removed or

modified. Keep guards in good working order.

• Shut off and lock out power source before

inspecting or servicing machine.

ENTANGLEMENT HAZARD

WARNING

20811

WARNING

UPENDING HAZARD

To prevent death or serious injury:

• Anchor intake end and/or support discharge end

to prevent upending.

• Intake end must always have downward weight.

Do not release until attached to tow bar or

resting on ground.

• Do not raise intake end above tow bar height.

• Empty tube and fully lower before moving.

MK/HX 10-36 – SWING-AWAY GRAIN AUGER 2. SAFETY FIRST

14 30549 R2

Table 1 Safety Decals (continued)

Part Number Description

20807

To prevent serious injury or death:

• Read and understand the manual before

assembling, operating, or maintaining the

equipment.

• Only trained personnel may assemble, operate,

or maintain the equipment.

• Children and untrained personnel must be kept

outside of the work area.

• Do not modify the equipment. Keep in good

working order.

• If the manual, guards, or decals are missing or

damaged, contact factory or representative for

free replacements.

• Lock out power before performing maintenance.

• To prevent equipment collapse or upending,

support equipment tube while disassembling

certain components.

• Follow grain storage structure manufacturer's

warnings when loading and unloading.

• Electric motors must be grounded. Disconnect

power before resetting overloads.

WARNING

2. SAFETY FIRST MK/HX 10-36 – SWING-AWAY GRAIN AUGER

30549 R2 15

Table 1 Safety Decals (continued)

Part Number Description

20803

To prevent serious injury or

death, shut off power and

reattach guard before operating

machine.

MISSING GUARD HAZARD

WARNING

17107

To prevent personal injury or

damage to equipment, close valve

in lift cylinder hydraulic line after

raising equipment into position.

CAUTION

18859

Disconnect PTO driveline

from tractor before moving

equipment.

If attached, driveline will

bottom out, severely

damaging the CV u-joint

and lower flight shaft.

See manual for

maintenance.

NOTICE

MK/HX 10-36 – SWING-AWAY GRAIN AUGER 2. SAFETY FIRST

16 30549 R2

Table 1 Safety Decals (continued)

Part Number Description

17531

To prevent

damage

during auger-

to-tractor

hookup:

NOTICE

• Follow dimensions above for

correct auger-to-tractor hookup.

• Auger must be on level ground and in

full down position when measuring.

• Adjust drawbar as needed.

See operation manual for complete details.

19960

To prevent damage, wheels must be

free to move when raising or lowering

equipment.

When equipment is positioned, chock

all wheels.

NOTICE

17093

Lubricate angle drive after

each 8 hours of use with

high-temperature grease.

NOTICE

2. SAFETY FIRST MK/HX 10-36 – SWING-AWAY GRAIN AUGER

30549 R2 17

3. Assembly

Before starting assembly of your new auger, please read the following instructions carefully and

familiarize yourself with all the sub-assemblies and hardware making up the auger. Ensure that all

parts are on hand, arranging them for easy access as required. Assembly should be carried out in a

large open area with a level surface.

Important

These instructions are written on the assumption that two or more people will be available for

the assembly procedure. Because of the weight, it is unwise to attempt assembly of auger

alone.

3.1. Arrange Tubes and Apply Model Decals

Identify and Arrange the Auger Tube Sections

1. Align tube sections on a series of support stands, placing a support stand at the end of each tube (see the

figures below for correct tube identification and positioning).

2. As tubes sections are added, make sure that support stands are at equal heights across all tubes to ensure

that tubes are level with each other. Otherwise, use some form of shim to keep the tubes level across all of

the support stands.

Important

Strap tubes to the support stands to prevent the tubes from rolling off the stands.

Figure 6. Auger Tube Sections

AGI DECAL

MODEL/SIZE DECAL

BRAND DECAL

24" (61 cm)

175" (444.5 cm)

BRAND DECAL

Apply the Logo and Model Decals on the Auger Tubes

Important

Do not cover any existing safety or instruction decals with the model decals.

1. Prepare surface by cleaning thoroughly with soap and water. Surface must be clean and free of dirt, grime,

rust and oil. To clean oily surface, wipe with clean cloth and solvent cleaner or isopropyl alcohol.

MK/HX 10-36 – SWING-AWAY GRAIN AUGER 3. ASSEMBLY

18 30549 R2

2. Apply decals to both sides of the auger tube. Center decals vertically on the tube and apply masking tape

along the top, creating a gate hinge. Figure A demonstrates.

3. Remove backing paper from decal 6" (15.2 cm) from the top and use the squeegee to adhere decal to the

tube, as seen in Figure B. Start at the top center of the decal and work your way outward both left and right

using overlapping strokes.

4. As you work your way down the decal, peel back the backing paper 6" (15.2 cm) at a time. Repeat Step 3

until the entire decal has been applied to the tube. See Figure C as an example.

5. Once the entire decal has been properly adhered to the tube, remove tape hinge from front of decal.

Remove the front application tape at a sharp 180° angle.

6. Inspect the entire decal for air pockets; if found, remove them by punching a tiny hole with a pin and then

squeegee the surface flat.

7. As a final process, squeegee the corners and edges of the decal to ensure proper adhesion and to prevent

premature peeling.

3. ASSEMBLY MK/HX 10-36 – SWING-AWAY GRAIN AUGER

30549 R2 19

3.2. Tube and Flight Assembly

1. Align upper and lower tube sections on a flat surface or on a series of benches.

2. Slide lower flight shaft into upper flight shaft with flight ends butting together for continuous flow. Secure

with two 1/2" x 2-3/4" grade 8 bolts and locknuts (see Figure 7).

3. Slide tube sections together and insert the eight 7/16" x 1" bolts and locknuts and tighten.

Block tube sections to prevent rolling. Do not drop. Damage to equipment or personal injury

will result.

Figure 7.

MK/HX 10-36 – SWING-AWAY GRAIN AUGER 3. ASSEMBLY

20 30549 R2

3.3. Trackshoe and Trackstop

1. Slide the roller trackshoe onto track, then attach the lower trackstop to the correct position on track as

shown in Figure 8, using two 7/16" x 1-1/4" bolts and locknuts.

Figure 8.

2. Attach the upper trackstop to correct position as shown in Figure 9, using two 7/16" x 1-1/4" bolts, locknuts

and heavy flat washers. Make certain the washers are on top of track as shown in Figure 9 and that the

trackstop is centered on the track.

3. Slide trackshoe along full length of track to make certain there is no binding.

Figure 9.

3. ASSEMBLY MK/HX 10-36 – SWING-AWAY GRAIN AUGER

Page is loading ...

AGI HX10-36 Swing-Away Grain Auger Assembly Manual

This manual is also suitable for

AGI HX10-36 Swing-Away Grain Auger Assembly Manual

Related papers

Other documents