Zenith D60DVSA Installation guide

Zenith
Brand
Zenith
Model
D60DVSA
Type
Installation guide

This manual is also suitable for

Zenith D60DVSA is a pair of 60V PDP speakers that can be mounted on a monitor, on a flat desk-type surface, or on the floor. They have a rated input of 10 watts and a maximum input of 20 watts. The speakers have a width of 5.3 inches (135 mm), a height of 34.8 inches (883 mm), and a depth of 3.9 inches (99 mm). They weigh 5.5 pounds (2.5 kg).

The speakers come with a variety of accessories, including four iron plates, four large bolts, eight small bolts, two speaker wire holders, and two speaker wires.

Zenith D60DVSA is a pair of 60V PDP speakers that can be mounted on a monitor, on a flat desk-type surface, or on the floor. They have a rated input of 10 watts and a maximum input of 20 watts. The speakers have a width of 5.3 inches (135 mm), a height of 34.8 inches (883 mm), and a depth of 3.9 inches (99 mm). They weigh 5.5 pounds (2.5 kg).

The speakers come with a variety of accessories, including four iron plates, four large bolts, eight small bolts, two speaker wire holders, and two speaker wires.

P/NO : 3828VA0279B
D60DVSA
D60DVSAS
D60DVSA
D60DVSAS
60V PDP Speakers & Speaker Stand
Installation and Setup Guide
2
206-3732
Speaker Installation
- Speakers can be mounted:
On the Monitor, (See below)
On a flat desk-type surface. (See page 3)
Or, on the floor. (See page 3)
Speakers mounted on the monitor
Speakers mounted on the monitor
3
206-3732
Speakers shown mounted on the speaker stands
Speakers shown mounted on the speaker stands
Speakers shown mounted on the floor stands
Speakers shown mounted on the floor stands
4
206-3732
Mounting speakers on Monitor
Mounting speakers on Monitor
G Caution: Always lift the monitor itself (not the speakers) when handling or moving the monitor after speakers
have been installed.
When screwing bolts into the Monitor and speakers, tighten the bolts enough so that they are secure. If the
bolts are tightened too much, the product could be damaged.
60V PDP Speakers
5
206-3732
Connecting Speakers to the Monitor using the speaker wires provided
Connecting Speakers to the Monitor using the speaker wires provided
(+)
( )
(+)( )
AUDIO
(MONO)
R L
AV INPUT
COMPONENT (480i/480p/720p/1080i)
(DVD/DTV INPUT)
RGB-PC INPUT
R
AUDIO INPUT
S-VIDEO
EXTERNAL SPEAKER
R L
L
AUDIO
(VGA/SVGA/XGA/SXGA)
RGB-DTV INPUT
(480p/720p/1080i)
VIDEO
Y P
B
P
R
(+) ( ) (+)( )
AUDIO
(MONO)
R L VIDEO Y P
B R
P
AV INPUT
AUDIO
R L
R
L
EXTERNAL SPEAKER (8Ω) AC INPUTAUDIO INPUT S-VIDEO
COMPONENT (480i/480p/720p/1080i)
RGB-PC INPUT
(VGA/SVGA/XGA/SXGA)
RGB-DTV INPUT
(480p/720p/1080i)
(DVD/DTV INPUT)
G Caution: Unplug monitor power cord from power outlet before making any connections.
G Place the speakers in the position you want. Install the speaker wires on the monitor and speaker. Be sure to
connect the positive “+” wire to the “+” input and the negative “-“ wire to the “–“ input. Connect left monitor
input to left speaker and right monitor input to right speaker. Any extra speaker wire length remaining can be
bunched into the wire holders provided, see 1 above to install wire holders. (Caution: Once installed, the
speaker wire holders lock into position and can’t be removed.)
6
206-3732
4-Iron Plates (Mount speakers
to monitor.)
8- Small Bolts (Attach iron
plates to speakers.)
4-Large Bolts (Attach iron
plates to monitor.)
2-Speaker Wire Holders (for
arranging the speaker wires.)
2-Speaker Wires Installation and
Setup Guide
Accessories
Accessories
Zenith
7
206-3732
Specifications
Specifications
Name of Product
Impedance (ohms)
Rated Input (watts)
Maximum Input
(watts)
Width (inches / mm)
60V PDP Speakers
8
10
20
5.3 / 135
Height (inches / mm)
34.8 / 883
Depth (inches / mm)
3.9 / 99
Weight (pounds / kg)
5.5 / 2.5
8
206-3732
G Assemble each speaker stand and speaker by screwing the two bolts in the clockwise direction shown in 1
above. See the magnified view to identify the two screw bolt holes.
To detach the speaker form the stand, unscrew the two bolts in the opposite direction.
Speaker
Speaker stand
How to mount speaker on Speaker stand
How to mount speaker on Speaker stand
60V PDP Speaker stand
9
206-3732
Accessories
Accessories
4 Bolts Installation and
Setup Guide
Specifications
Specifications
Name of Product
Width (inches / mm)
Height (inches / mm)
Depth (inches / mm)
Weight (pounds / kg)
60V PDP Speaker stand
8.7 / 220
8.6 (38.5) / 218 (978.5)
*The value in ( ) is the height of the assembled speaker and stand.
8.7 / 220
4 / 1.8
Zenith
10
206-3732
Memo
11
206-3732
Memo
206-3732
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12

Zenith D60DVSA Installation guide

Zenith
Brand
Zenith
Model
D60DVSA
Type
Installation guide
This manual is also suitable for

Zenith D60DVSA is a pair of 60V PDP speakers that can be mounted on a monitor, on a flat desk-type surface, or on the floor. They have a rated input of 10 watts and a maximum input of 20 watts. The speakers have a width of 5.3 inches (135 mm), a height of 34.8 inches (883 mm), and a depth of 3.9 inches (99 mm). They weigh 5.5 pounds (2.5 kg).

The speakers come with a variety of accessories, including four iron plates, four large bolts, eight small bolts, two speaker wire holders, and two speaker wires.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents