Carel PoolPak ECCIII Installation guide

Type
Installation guide
© 2019 PoolPak LLC. All rights reserved. 717-757-2648 | www.PoolPak.com | Page 1
ECCIII Remote Interface Unit
Installation Instructions (24-0102)
ECCIII REMOTE INTERFACE UNIT (RIU) INSTALLATION
PoolPak Part #: 24-0102
Manufacturer: Carel
PPK Models: PoolPak SWHP, ClimatePak VHR, PoolComPak TD-2000, TD-2500, TD-3000
Failures due to mounting the keypad inside the pool room will not be covered under warranty.
! WARNING
INTRODUCTION
The Remote Interface Unit (RIU) is the main user interface for the ECC control systems. It can be installed at the PoolPak
unit or in another convenient location up to 1000 feet away. Each PoolPak supports connection to as many as three
RIUs. All status, set points and configuration points are available through the RIU.
MOUNTING
The RIU should be mounted in a convenient location, outside the natatorium, that is protected from splashing pool
water and corrosive air. The ambient temperature of the mounting location must always be greater than 3F. The
maximum distance from the PoolPak control panel is 1,000 feet. For distances greater than 1,000 feet, contact the
factory.
The RIU includes a mounting bracket that is designed to fit a standard, single-gang box, mounted horizontally in the
wall. Do not use the “through-the-wall” mounting option. The RJ25 jack and most of the black cable should be placed
inside the box before installing the mounting bracket. Use the screws that come with the box to secure the bracket.
Using an “extra deep” box will make it easier to fit the RJ25 cable and jack inside. After the mounting bracket is
secured to the wall, connect the RJ25 cable to the jack on the back of the RIU. Slide the RIU onto the bracket until it
snaps into place.
WIRING
Proper polarity and connection is essential for correct operation of the RIU. Improper wiring can cause permanent
damage. See below for the correct cable to connect the RIU (plug in back) with each model controller. At minimum,
cable must be 6-conductor (three twisted pairs), 16-20 AWG.
For hard-wiring the RIU to the controller, refer to the field wiring diagram in the Installation and Operation Manual
specific to your unit.
ECCIII Remote Interface Unit Installation Instructions
CONFIGURATION
The RIU network address is set by pressing the UP, DOWN, and ENTER buttons simultaneously and holding them down
for approximately 5 seconds. The display will show “Display address setting. Press the ENTER to move the cursor to
the current address field. Use the UP and DOWN buttons to change the address to either 10, 11, or 12 and press
ENTER.
To configure the ECC III RIU addresses, press the UP, DOWN, and ENTER buttons simultaneously and hold them down
for approximately 5 seconds. The display will show “Display address setting. Press the ENTER four times to move the
cursor past the screens showing “Display address setting, “I/O Board address” and “Terminal config Press ENTER to
continue. Use the keypad to enter the RIU configuration as follows:
P: 0x
Trm1
Trm2
Trm3
Priv/Shared
Sh
Sh
Sh
(x = CM1 I/O address)
Ok? Y
Adr
10
11
12
ASHRAE
6 2 .1 -2 013
3491 Industrial Drive
York, Pennsylvania 17402 USA
717-757-2648 | www.PoolPak.com
© 2019 PoolPak LLC. All rights reserved. RPW02-ECC3RIUII-20190517
When prompted “OK?”, select “Y” to save the configuration and to exit. The RIU will go blank and then beep several
times before bringing up the normal status display.
Note: Keypad’s no longer use dip switch configuration. For pre-existing keypads with dip switch configuration, refer to
the legacy document Remote Interface Unit Configuration.
If you have any questions, please call the PoolPak Service department at 717-757-2648.
CONTROLLER TYPE OF CABLE CONTROL CONNECTION
ECCIII RJ-12 Black Crossover Plug J10 CM1
ECCPCP RJ-12 Black Crossover Plug J10 CM1
TD3000 RJ-12 Black Crossover Plug J10 on TD3000 Cont.
TD2500 RJ-12 White Straight Through Plug on TD2500 Controller
TD2000 RJ-12 White Straight Through Plug on TD2000 Controller
  • Page 1 1
  • Page 2 2

Carel PoolPak ECCIII Installation guide

Type
Installation guide

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI