Proline PROLINE VDP610M User guide
- Category
- Tumble dryers
- Type
- User guide
This manual is also suitable for
Proline PROLINE VDP610M tumble dryer offers energy-saving and gentle fabric care with its range of drying programs and features. Equipped with a large capacity drum, it efficiently handles various loads, ensuring even drying results. The anti-crease function minimizes wrinkles, while the delay start option allows you to set the drying cycle to begin at a convenient time. Additionally, the lint filter captures lint and fibers to maintain optimal drying performance.
Proline PROLINE VDP610M tumble dryer offers energy-saving and gentle fabric care with its range of drying programs and features. Equipped with a large capacity drum, it efficiently handles various loads, ensuring even drying results. The anti-crease function minimizes wrinkles, while the delay start option allows you to set the drying cycle to begin at a convenient time. Additionally, the lint filter captures lint and fibers to maintain optimal drying performance.
10
CONTENTS
QUICK REFERENCE GUIDE
PROGRAMME CHART
PREPARING THE LAUNDRY
SELECTING A PROGRAMME AND OPTIONS
STARTING AND COMPLETING A PROGRAMME
CHANGING A PROGRAMME
INTERRUPTING A PROGRAMME
DAILY MAINTENANCE AND CLEANING
INSTRUCTIONS FOR USE
BOOKLET
SAFETY ADVICES BEFORE USING THE DRYER /
CONNECTIONS
PAGE
11
ELECTRICAL CONNECTION
PAGE
12
SAFETY ADVICES AND GENERAL
RECOMMENDATIONS
PAGE
13
DESCRIPTION OF THE DRYER
PAGE
14
REMINDER - MAINTENANCE AND CLEANING
PAGE
14
VENT CONNECTION
PAGE
15
DOOR REVERSIBILITY
PAGE
16
TROUBLESHOOTING GUIDE / AFTER-SALES SERVICE
PAGE
17
11
SAFETY ADVICES BEFORE USING THE DRYER /
CONNECTIONS
1. Removing the packaging and check
•
After unpacking, make sure that the dryer is
undamaged. If in doubt, do not use the dryer.
Contact After-Sales Service or your local retailer.
•
Keep the packaging materials (plastic bags,
polystyrene parts, etc.) out of reach of children, as
they are potentially dangerous.
If the appliance was exposed to the cold prior to
delivery, keep it at room temperature for a few
hours before operating.
2. Electrical Connections
•
Electrical connections must be carried out by a
qualified technician in compliance with the
manufacturer’s instructions and current standard
safety regulations.
•
Electrical connection must comply with local
Electricity Board regulations.
•
Voltage information, power consumption and the
required fuse protection is shown on the rating
plate mounted at the rear of the dryer.
•
The manufacturer cannot accept any liability for
personal injury or damage to property resulting
from failure to adhere to these instructions.
•
The dryer must be earthed as prescribed by law.
•
Do not use extension leads or multiple adaptors.
•
Do not use electrical portable outlet devices.
•
Before any maintenance on the dryer disconnect it
from the mains supply.
•
Do not operate the dryer if it has been damaged
during transport. Contact one of our After-Sales
Service technicians.
•
Mains cable replacement is only to be carried out by
After-Sales Service.
•
After installation access to the mains plug has to be
guaranteed, or the all-pole disconnection has to be
possible with a switch.
3. Installation
•
Do not install your dryer where it can be subject to
extreme conditions, such as: poor ventilation,
temperatures below 5°C or above 35°C.
•
The appliance must not be installed behind a
lockable door, a sliding door or a door with a hinge
on the opposite side to that of the tumble dryer.
•
Take care not to install the dryer on a deep-pile
carpet.
•
Take care not to trap the mains cable between the
dryer and the wall.
•
The exhaust-air must not be leaded into a air-outlet
conduit which is used for heating appliances fired
with gas, oil or solid fuel.
•
Pay attention that the air-inlet openings are
unobstructed.
Stability:
When installing the dryer always carefully level the
dryer adjusting the two feet and check the correct
levelling with a spirit level.
To built in the dryer
•
For security reasons do not remove the worktop.
•
Connect the dryer to an external ventilation system
in order to prevent steam from damaging your
furniture during the years.
Stacking kit
Your dryer can be stacked on top of your front
loading washing machine. Please contact your
dealer or our After Sales Service.
Minimum housing dimensions:
Width: 600 mm
Height: 855 mm
Depth: 560 mm
12
ELECTRICAL CONNECTION
1) For Great Britain only
Warning - this appliance must be earthed
Fuse replacement
If the mains lead of this appliance is fitted with a BS 1363A 13amp
fused plug, to change a fuse in this type of plug use an A.S.T.A.
approved fuse to BS 1362 type and proceed as follows:
1.
Remove the fuse cover (
A
) and fuse (
B
).
2.
Fit replacement 13A fuse into fuse cover.
3.
Refit both into plug.
Important:
The fuse cover must be refitted when changing a fuse and if the fuse
cover is lost the plug must not be used until a correct replacement is
fitted.
Correct replacement are identified by the colour insert or the colour
embossed in words on the base of the plug.
Replacement fuse covers are available from your local electrical
store.
2) For the Republic of Ireland only
The information given in respect of Great Britain will frequently
apply, but a third type of plug and socket is also used, the
2-pin, side earth type.
3) Socket outlet / plug (valid for both countries)
If the fitted plug is not suitable for your socket outlet, please contact
Whirlpool Service for further instruction. Please do not attempt to
change plug yourself. This procedure needs to be carried out by a
qualified Whirlpool technician in compliance with the manufactures
instructions and current standard safety regulations.
13
SAFETY ADVICES AND GENERAL
RECOMMENDATIONS
1. Packing
The packing box may be fully recycled as
confirmed by the recycling symbol.
2. Energy saving tips
•
Always dry a full load: depending on the type of
laundry and the programme/drying time.
•
By preference use the maximum spin speed
allowed by your washing machine, since draining
the water mechanically requires less energy.
•
Do not overdry the laundry.
•
Clean the lint filter after
every
drying cycle.
•
Place your dryer in a room with a temperature
between 15° C and 20° C. In case of higher
temperature ventilate the room.
•
Always select the correct programme/drying time for
the load in order to obtain the desired drying results.
•
Select the gentle option only with small loads.
•
When drying cotton, for example: dry iron dry and
cupboard dry loads together. Start with the iron dry
programme/drying time setting, remove the laundry to
be ironed at the end of that cycle and dry the remainder
of the load on the cupboard dry setting.
3. Disposing of packaging and old appliances.
The dryer is built from reusable materials. The
dryer must be disposed of in compliance with local
waste disposal regulations.
•
Before scrapping, cut off the power cable so that
the dryer cannot be connected to the mains.
4. Child safety:
Children must not be allowed to play with the dryer.
The appliance is not intended for use by young
children or infirm persons without supervision.
5. General recommendations:
•
The tumble dryer is intended only for drying textile
material washed in water.
•
Always set the programme/time selector knob to
the “0” position after use. This prevents the dryer
from being switched on accidentally.
•
Before cleaning or carrying out maintenance, switch off
the dryer and disconnect it from the mains supply.
•
To clean the outside of the dryer, use a neutral
detergent and a damp cloth.
•
Do not use abrasive detergents.
•
Do not use inflammable cleansing agents.
•
Do not use the tumble dryer if industrial chemicals
have been used for cleaning.
•
Garments treated or contaminated with flammable
cleaning sprays or liquids such as petrol, cooking oil
or aerosol sprays must not be put in this dryer.
•
Items that have been soiled with substances such as
cooking oil, acetone, alcohol, petrol, kerosene, spot
removers, turpentine, waxes and wax removers
should be washed in hot water with an extra amount
of detergent before being dried in the tumble dryer.
•
Items such as foam rubber (latex foam), shower
caps, waterproof textiles, rubber backed articles
and clothes or pillows fitted with foam rubber pads
should not be dried in the tumble dryer.
•
Fabric softeners, or similar products, should be
used as specified by the fabric softener instructions.
•
Lighters must not be left in pockets.
•
Never use and store flammable materials nearby
the dryer.
•
Wipe away lint from the door seal and the door
using a damp cloth.
•
If the lint filter mesh is clogged, clean it with water
and a soft brush.
•
Since lint can go through the filter, it is necessary to
clean, from time to time, the complete filter area
(including below the filter) with a brush, a damp
cloth or with a vacuum cleaner.
•
If necessary, the power cable may be replaced with
an identical one obtained from our After-Sales
Service. The power cable must only be replaced by
a qualified technician.
•
Attention rear panel can be hot.
EC Declaration of Conformity
•
This dryer has been designed, constructed and
distributed in compliance with the safety
requirements of EC Directives:
•
2006/95/EG Low voltage Directive
•
2004/108/EC Electromagnetic Compatibility Directive
•
This appliance is marked according to the European
directive 2002/96/EC on Waste Electrical and
Electronic Equipment (WEEE).
By ensuring this product is disposed of correctly,
you will help prevent potential negative
consequences for the environment and human
health, which could otherwise be caused by
inappropriate waste handling of this product.
The symbol on the product, or on the
documents accompanying the product, indicates
that this appliance may not be treated as household
waste. Instead it shall be handed over to the
applicable collection point for the recycling of
electrical and electronic equipment.
Disposal must be carried out in accordance with
local environmental regulations for waste disposal.
For more detailed information about treatment,
recovery and recycling of this product, please contact
your local city office, your household waste disposal
service or the shop where you purchased the product.
•
The dryer must be used in the household for the
described uses.
14
DESCRIPTION OF THE DRYER
REMINDER - MAINTENANCE AND CLEANING
A.
Work top
B.
Contact pin
C.
Door
To open the door:
pull the handle
To close the door:
push gently until closed.
D.
Filter
EACH DRYING CYCLE
• Clean the lint filter at the end of every
drying cycle.
Open the door.
Pull the filter upwards.
Remove lint using a soft brush or your
fingertips.
Push the filter back into place.
EACH THREE MONTHS
•
Clean venthose and connection regularly to
avoid blockage due to lint or foreign objects.
A
B
C
D
15
VENT CONNECTION
Normally the hose and adaptor are not supplied; the accessory kit,
available at your dealer or our After Sales Service, should be used.
Installing the vent hose
A.
Place a towel or the packing material on the right-hand side next
to the dryer.
B.
Place the dryer on its right-hand side (seen from the front) on the
towel or the packing material.
C.
Push the adapter into the hose (see illustration). Attach the air vent
hose adapter to the connection located under the dryer and lock
it by means of the foreseen lugs.
Venting outside
•
Without kinking it, lead the vent hose outside (inside diameter 10
cm, maximum length with two bends 3 m).
•
Ensure that the vent hose does not sag when stacking the dryer on
a washing machine. It should only be placed horizontally or
upwards.
•
Do not connect to ventilation systems protected by fly nets. These
can become clogged and cause malfunctioning of the dryer.
•
Do not connect the air vent hose to a chimney or to a mechanical
ventilation extractor duct.
•
Do not connect the vent hose to the heating system. Only connect
the hose to ventilation systems insulated against humidity.
•
Please provide adequate ventilation to avoid the back flow of gases
into the room from appliances burning other fuels, including open
fires.
Dryer operation without vent hose
•
Only use the dryer in a large, well-ventilated room.
•
Keep the room free of dust and lint.
A minimum distance of 10 cm between rear of appliance and the wall
must be observed.
Dryer placed close to the wall; venting to the left or right
Install the dryer by using the bi-directional kit, available at your dealer.
IMPORTANT
• Do not connect to ventilation systems protected by fly nets.
These can become clogged and cause malfunctioning of the
dryer.
For example, alternative to be
used.
C
16
DOOR REVERSIBILITY
Door Reversibility
A. Unplug the dryer.
B.
Open the door.
C.
Using a spanner, turn the contact pin on the inside of the door
(top) through 90° and remove it.
D.
Remove the 2 door hinge screws, followed by the door.
E.
Unscrew the 2 screws above and below the door lock system.
F.
Removing the door lock: using a screwdriver, press down on the
small rib in the upper opening and extract the door lock by pulling
it towards you.
G.
Reverse the door:
H.
Fasten the door on the desired side using the 2 screws.
I.
Insert the door lock system on the opposite side and lock it
securely.
J.
Fix the 2 screws above and below the door lock system.
K.
Replace the contact pin in the inside of the door (top).
D
C
F
E
E
C
17
TROUBLESHOOTING GUIDE / AFTER-SALES
SERVICE
Troubleshooting Guide
If a fault occurs, before contacting our After-
Sales Service, make the following checks to
try and remedy the problem:
Drying takes too long / laundry is not dry
enough:
•
Was the correct programme selected?
•
Was the inserted laundry too wet (Washing
machine spin speed less than 800 rpm)?
•
Is the lint filter dirty (filter indicator lamp on)?
•
Does “END” and “Anti-Crease” LED’s are lights
up? - The drying cycle is terminated, the laundry can
be taken out.
T
he dryer does not operate:
(following a power failure and/or
interruption to the mains supply, always
press the Start button).
•
Is the plug properly inserted into the mains
electricity socket?
•
Is there a power failure?
•
Has the fuse blown?
•
Is the door well closed?
•
Has the programme been selected?
•
Has the start delay option been selected?
•
Has the
Start/Pause
button been pressed?
Lint filter indicator lamp light on:
•
Is the lint filter clean?
•
Is the vent hose blocked?
•
Is the outside vent hose adaptor blocked ?
After-Sales Service
If, after carrying out the above checks the
malfunction persists or appears again, turn
the dryer off and call our After-Sales Service
(refer to guarantee).
Please specify:
•
The nature of the fault.
•
The dryer type and model.
•
The service code (the number after the word
Service on the adhesive rating plate) on the right-
hand side when the door is open.
•
Your full address and phone number.
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
Proline PROLINE VDP610M User guide
- Category
- Tumble dryers
- Type
- User guide
- This manual is also suitable for
Proline PROLINE VDP610M tumble dryer offers energy-saving and gentle fabric care with its range of drying programs and features. Equipped with a large capacity drum, it efficiently handles various loads, ensuring even drying results. The anti-crease function minimizes wrinkles, while the delay start option allows you to set the drying cycle to begin at a convenient time. Additionally, the lint filter captures lint and fibers to maintain optimal drying performance.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Whirlpool MYU070EDWT MM User guide
-
Whirlpool AWZ 3789 WP Owner's manual
-
Whirlpool TRKD 4678 Owner's manual
-
Whirlpool AWZ 3669 WP User guide
-
-
Whirlpool AWZ 3518 WP User guide
-
-
-
LADEN EP3598 LA User guide
-