White Westinghouse WWFC18M4RC User guide

Brand: White Westinghouse

Model: WWFC18M4RC

Type: User guide

This manual is also suitable for

WWFC16M4RC

TABLE OF CONTENTS

All about the

Use & Care

of your Freezer

A04704301 (August 2015)

Product Registration....................................2

Important Safety Instructions ......................2

First Steps .................................................4

Setting the Temperature Control ..................7

Optional Features .......................................8

Energy-Saving Tips .....................................9

Care and Cleaning ......................................9

Power/Freezer Failure................................11

Before you Call .........................................11

Major Appliance Warranty .........................14

PRODUCT REGISTRATION

Read and Save These Instructions

This Owner’s Guide provides specic operating

instructions for your model. Use your appliance

only as instructed in this guide. These

instructions are not meant to cover every

possible condition and situation that may occur.

Common sense and caution must be practiced

when installing, operating, and maintaining

any appliance.

Record Your Model and

Serial Numbers

Record the model and serial numbers in the

space provided below.

Model Number:

Serial Number:

Purchase Date:

Denitions

This is the safety alert symbol. It is used to

alert you to potential personal injury hazards.

Obey all safety messages that follow this

symbol to avoid possible injury or death.

WARNING

Please read all instructions before using

this unit.

DANGER

DANGER indicates an imminently hazardous

situation which, if not avoided, will result in

death or serious injury.

WARNING

WARNING indicates a potentially hazardous

situation which, if not avoided, could result

in death or serious injury.

CAUTION

CAUTION indicates a potentially hazardous

situation which, if not avoided, may result in

minor or moderate injury.

IMPORTANT

IMPORTANT indicates installation, operation

or maintenance information which is

important but not hazard-related.

Product

The self-addressed

PRODUCT

REGISTRATION CARD

should be lled in completely,

signed and returned to the address provided.

WARNING

Child Safety

• Destroy carton, plastic bags, and any exte-

rior wrapping material immediately after the

unit is unpacked. Children should never use

these items for play. Cartons covered with

rugs, bedspreads, plastic sheets or stretch

wrap may become airtight chambers and

can quickly cause suffocation.

• An empty, discarded appliance is a very

dangerous attraction to children.

• Remove the door(s) of any appliance that

is not in use, even if it is being discarded.

IMPORTANT SAFETY

INSTRUCTIONS

WARNING

For Your Safety

• Do not store or use gasoline or other

ammable vapors and liquids in the vicin-

ity of this unit or any other appliance.

Read product labels for ammability and

other warnings.

• Do not operate the unit in the presence of

explosive fumes.

• Remove and discard any spacers used to

secure the shelves during shipping. Small

objects are a choke hazard to children.

• Remove all staples from the carton.

Staples can cause severe cuts, and also

destroy nishes if they come in contact

with other appliances or furniture.

IMPORTANT SAFETY INSTRUCTIONS

WARNING

Proper Disposal of Your Appliance

Risk of child entrapment

Child entrapment and suffocation are not

problems of the past. Junked or abandoned

appliances are still dangerous – even if they

will sit for “just a few days”. If you are getting

rid of your old appliance, please follow the

instructions below to help prevent accidents.

We strongly encourage responsible

appliance recycling/disposal methods. Check

with your utility company or visit www.

recyclemyoldfridge.com for more information

on recycling your old appliance.

Before you throw away

your old appliance:

• Remove door/lid.

• Leave shelves in place

so children may

not easily

climb inside.

• Have the

refrigerant

removed by a

qualied technician.

Grounding type wall receptacle

Power cord with

3-prong grounded plug

Do not, under

any circumstances,

cut, remove,

or bypass the

grounding prong.

WARNING

Avoid re hazard or electric shock. Do not

use an extension cord or an adapter plug.

Do not remove any prong from power cord.

WARNING

Electrical Information

These guidelines must be followed to ensure

that safety mechanisms in the design of this

appliance will operate properly.

• Refer to the serial plate for correct electri-

cal rating. The power cord of the appliance

is equipped with a three-prong grounding

plug for your protection against electrical

shock hazards. It must be plugged directly

into a properly grounded three-prong

receptacle, protected with a 15-amp time

delay fuse or circuit breaker. The recep-

tacle must be installed in accordance with

the local codes and ordinances. Consult a

qualied electrician. Receptacles protected

by Ground Fault Circuit Interrupters (GFCI)

are NOT RECOMMENDED. Do NOT use an

extension cord or adapter plug.

• If the power cord is damaged, it should be

replaced by an authorized service techni-

cian to prevent any risk.

• Never unplug the appliance by pulling on

the power cord. Always grip the plug rm-

ly, and pull straight out from the receptacle

to prevent damaging the power cord.

• Unplug the appliance before cleaning

and before replacing a light bulb to avoid

electrical shock.

• If voltage varies by 10% or more, appliance

performance may be affected. Operating

the unit with insufcient power can dam-

age the motor. Such damage is not covered

under the warranty. If you suspect your

household voltage is high or low, consult

your power company for testing.

• To prevent the appliance from being turned

off accidentally, do not plug unit into an out-

let controlled by a wall switch or pull cord.

• Do not pinch, knot, or bend power cord in

any manner.

WARNING

Other Precautions

• To defrost appliance, always unplug unit rst.

• Never unplug the unit by pulling on the

power cord. Always grip the plug rmly

and pull straight out from the receptacle.

• Turning the control to OFF turns off the

compressor, but does not disconnect

power to other electrical components.



NOTE

It is VERY IMPORTANT for your appliance

to be level in order to function properly. If the

unit is not leveled during installation, the door/

lid may be misaligned and not close or seal

properly, causing cooling, frost or moisture

problems.



NOTE

The exterior walls of the unit may become

quite warm as the compressor works to

transfer heat from the inside. Temperatures

as much as 30° F warmer than room

temperature can be expected. For this reason

it is particularly important in hotter climates

to allow enough space for air circulation

around your appliance.

Leveling

The appliance must have all bottom corners

resting rmly on a solid oor. The oor must be

strong enough to support a fully loaded unit.

This Use & Care Guide provides general operating

instructions for your model. Use the unit only

as instructed in this Use & Care Guide. Before

starting the unit, follow these important

rst steps.

Location

Choose a place that is near a grounded

electrical outlet.

For the most efcient operation, the appliance

should be located where surrounding

temperatures will not exceed 110°F (43°C).

Temperatures of 32°F (0°C) and below will

NOT affect operation. Additional compressor

heaters are not recommended.

Allow space around the unit for good air

circulation. Leave a 3 inch (75 mm) space on

all sides of the unit for adequate circulation.

CAUTION

To allow door to close and seal properly, DO

NOT let food packages extend past the front

of shelves.

3” (75 mm)

3” (75 mm) Air Space

3” (75 mm)

To level Upright Units:

After discarding crating screws, use a

carpenter’s level to level the appliance from

front to back. Adjust the plastic leveling feet in

front, ½ bubble higher, so that the door closes

easily when left halfway open.

Repositioning the Mid-Level

Basket (some models):

1. To remove the support-hanging basket,

press upward on underside of front of

support to release from shelf rod.

2. Rotate front under the shelf, and then

slide support-hanging basket forward to

remove from back shelf rod.

3. To remove shelf grommet, slide away

from wall, then pull from rod.

4. Repeat steps 1-3 for other side.

5. With the shelf installed, press the 2 shelf

grommets down onto the rod that is

3" (75 mm)

(75 mm)

Installation

FIRST STEPS

To level Chest Units:

If needed, add metal or wood shims between

feet pads and oor.

FIRST STEPS

6. Push the shelf grommets onto the shelf

rod until rmly seated.

7. Slide the shelf grommets into the wall

grommets already in the unit wall until

they are ush.

1. Place the basket on a rm, at surface.

2. With the narrow side of the handle clip on

the inside of the basket, snap the handle

clip to the recessed area in the basket.

To install the handle clips to the basket:

3. Once the inside surface snaps in place,

continue the process by rolling the

handle clip slightly outward and pressing

down rmly to snap onto the outside

surface. If installed incorrectly, the

handle clip will not lay at.

8. Guide the support-hanging basket

underneath the shelf, inserting the

slotted end of the support onto the rear

shelf rod.

9. Rotate the support-hanging basket up

to bring the front end over the front

shelf rod. Slide forward to locate front

of support-hanging basket over front of

shelf rod. Push down on support until it

snaps into place.

anchored into the appliance wall (located

in the back only). Be sure to keep the

larger end of the shelf grommets away

from the wall.



NOTE

Your freezer may have some, or all of the

features listed below. Become familiar with

these features, and their use and care.

Cool Down Period

• For safe food storage, allow 4 hours for

the appliance to cool down completely.

The unit will run continuously for the rst

several hours. Foods that are already

frozen may be placed in the unit after the

rst few hours of operation. Unfrozen foods

should NOT be loaded into freezer until

freezer has operated for 4 hours.

• When loading freezer, freeze only 3 pounds

of fresh food per cubic foot of freezer

space at one time. Distribute packages to

be frozen evenly throughout the freezer. It

is not necessary to turn control knob to a

colder setting while freezing food.

Electromechanical Temperature

Control (chest and some upright models)

The temperature control is located inside the

freezer on upright models, and on the left

exterior wall on chest models. The temperature

is factory preset to provide satisfactory

food storage temperatures. However, the

temperature control is adjustable to provide

a range of temperatures for your personal

satisfaction. If a colder temperature is

desired, turn the temperature control knob

toward COLDEST and allow several hours for

temperatures to stabalize between adjustments.

Electronic Temperature Control

(some upright frost-free models)

The electronic temperature control is located

outside the freezer on upright models. The

temperature is factory preset to provide

satisfactory food storage temperatures. To

adjust the temperature setting, press the +

button for a warmer temperature and the -

button for a colder temperature on the control

panel. Allow several hours for the temperature

to stabilize between adjustments.

SETTING THE

TEMPERATURE CONTROL

Door Removal (upright models)

If door must be removed, unplug the unit.

1. Gently lay the unit on its back, on a rug

or blanket.

2. Remove 2 base screws and base panel.

3. Unplug connector, if required, by holding

the cabinet connector in place, and

pulling door connector out. If equipped,

pull Harness Retainer from Cabinet.

4. Remove 4 bottom hinge screws.

5. Remove plastic top hinge cover.

6. Remove 2 screws from top hinge.

7. Remove top hinge from cabinet.

8. Remove door and bottom hinge

from cabinet.

9. To replace door, reverse the above

order and securely tighten all screws to

prevent hinge slippage. Ensure the door

harness is routed as shown and that the

restraint clip is snapped into the cabinet.

Base Screw

Hinge

Screws

Wire

Door

Connector

Cabinet

Connector

Harness

Restraint

Lid Removal (chest models)

See Instructions on hinge label. Unplug the unit.

FIRST STEPS

OFF

ALARM

DEMO

HRS

POWER FAILHIGH TEMP

DOOR AJAR

ºC

REFRIGERATOR

FREEZER

ºF

quick freeze

power off

exit

control lock

PRESS

& HOLD

Electronic Temp Alarm

If a malfunction causes an unsafe temperature

inside the freezer, the high temp will display on

the control panel and the alarm will sound. To

silence the alarm, press the set button next to

the “alarm off” indicator on the display or any

key on the control panel.

Quick Freeze

Quick freeze can be enabled by entering into

the options menu on the control panel and by

pressing the “set” button once the indicator

is highlighted next to “quick freeze”. The unit

will be in quick freeze mode for 72 hours and

will show a snowake indicator on the control

panel to indicate that it is in quick freeze

mode. To exit quick freeze mode, enter into

the options menu on the control panel and

press the “set” button once the indicator is

highlighted next to “quick freeze”, after which

the snowake indicator will be removed from

the control panel. Or quick freeze will end

automatically after 72 hours.

Control Lock

Control lock can be enabled by entering into

the options menu on the control panel and by

pressing the “set” button once the indicator

is highlighted next to “control lock”. A control

lock icon will be displayed on the control

panel to indicate that the control panel has

been locked. To unlock, press and hold the

set button for 3 seconds, after which the lock

indicator will be removed from the control

panel and the control panel has been unlocked.

Temperature Conversion

Press and hold both temperature buttons ("+"

and "-") to toggle between °F and °C.

SETTING THE

TEMPERATURE CONTROL

Power Off

To shut cooling off to the unit and to turn off

the interior lights of the unit, enter into the

options menu on the control panel and press

and hold the “set” button for 3 seconds once

the indicator is highlighted next to “power

off”. “Power off” will be displayed on the

control panel to indicate that the unit is in the

powered off mode. To turn power back on to

the unit, press and hold the “set” key for 3

seconds. Then the power off indicator will be

removed from the control panel and the set

point of the unit will be displayed again.

Power Fail

If your unit has lost power, the control panel

will display “power fail” and the number of

hours that your unit has been without power

up to a maximum of 48 hrs. The alarm will

sound until the condition is acknowledged by

pressing the set button or any other button on

the control panel.

Door Ajar

If your door has been left open for more 5

minutes, the control panel will display “door

ajar” and will sound an alarm until the door

has been closed or any button is pressed on

the control panel. If a button on the control

panel has been pressed but the door has not

been closed, “door ajar” will continue to be

displayed on the control panel until the door

has been closed.

Sabbath Mode

The Sabbath mode is a feature that disables

portions of the appliance and its controls in

accordance with observance of the weekly

Sabbath and religious holidays within the

Orthodox Jewish community.

To turn Sabbath mode on, press and hold

the “Options” button and “+” button for 5

seconds, after which “Sb” will be displayed on

the control panel indicating that the unit is in

Sabbath mode. To exit Sabbath mode, press

and hold the “Options” button and “+” button

for 5 seconds, after which the display will

return to displaying the set point of the unit.

In the Sabbath mode, the High Temp alarm

is active for health reasons. If a high

temperature alarm is activated during this

time, for example, due to a door left ajar, the

alarm will sound for about 10 minutes. The

alarm will then silence on its own and a “high

temp” icon will be displayed on the control

panel. The high temp icon will continue to

display even if the door is closed until Sabbath

mode is exited and the icon reset.

OPTIONAL FEATURES



NOTE

While in Sabbath mode, neither the lights

nor the control panel will work until Sabbath

mode has been deactivated.

The unit stays in Sabbath mode after a power

failure recovery. It must be deactivated with

the buttons on the control panel.

Adjustable Shelf

(some upright models)

This shelf can be moved to 1 or 2 positions.

Move to the right and lift left to move to the

desired location.

For further assistance, guidelines of

proper usage and a complete list of

models with the Sabbath feature,

please visit the web at

http:\\www.star-k.org.

Slide-Aside Basket

(some chest models)

This basket helps organize

odd-shaped items. To

reach other packages

in the freezer, slide the

basket aside or lift out.

Fast Freezing Shelves

(manual defrost upright models)

These shelves contain cooling coils to freeze

foods quickly and allow cold air to constantly

circulate throughout the freezer. Do not

use sharp metal objects such as ice picks

or scrapers to clean the shelves. This could

damage the shelves and reduce their cooling

ability. These shelves are not adjustable.

Soft Freeze Zone

(some upright models)

Soft Freeze Zone is

specically designed

to maintain a higher

temperature than the rest of the freezer to

store products such as ice cream.

OPTIONAL FEATURES

Adjustable Door

Bins (some upright

models)

Adjustable door bins are

located inside on the

freezer door and provide

exible storage space. The number of bins

provided varies by model.

Pizza Shelf (some

upright models)

Here is the place to store

up to four extra-large

boxes of frozen pizza

without ever having to dig

them out from beneath a

pile of other stored goods.

The pizza shelf can be retracted to provide

space for larger items on the shelf below and

still store up to 2 pizzas.

Mid-Level Basket

This basket keeps things

organized and slides out

for easy access.

Basket Divider

(some upright models)

Use these handy dividers

to keep the various

items stored in your

baskets more organized.

To change the location of the divider simply

slide your basket out, grab the divider from

the center and rotate in a counterclockwise

direction until it is desengaged. To assemble,

simply align as shown in the gure below and

rotate in a clockwise direction until it spans

into place.

Power On Light

The Power On Light indicates that the

appliance is properly connected to electrical

power. The light glows even when the

temperature control is turned to OFF. If the

light goes out, refer to “Appliance does not

run” in the Before You Call section.

ENERGY-SAVING TIPS

• The appliance should

be located in the

coolest area of the

room, away from heat

producing appliances

or heating ducts, and

out of direct sunlight.

• Let hot foods cool to room temperature

before placing in the unit. Overloading the

appliance forces the compressor to run

longer. Foods that freeze too slowly may

lose quality or spoil.

• Be sure to wrap foods properly and wipe

containers dry before placing them in the

unit. This cuts down on frost build-up

inside the unit.

• Shelves and baskets should not be lined

with aluminum foil, wax paper, or paper

toweling. Liners interfere with cold air

circulation, making the freezer less efcient.

• Organize and label food to reduce door

openings and extended searches. Remove

as many items as needed at one time, and

close door as soon as possible.

CARE AND CLEANING

CAUTION

Damp objects stick to cold metal surfaces.

Do not touch interior metal surfaces with

wet or damp hands.

Some upright freezers are frost-free and defrost

automatically, but should be cleaned occasionally.

Between Defrosting

To avoid frequent defrosting, occasionally use

a plastic scraper to remove frost. Scrape with

a pulling motion. Never use a metal instrument

to remove frost.

CAUTION

Freezer must be unplugged (to avoid

electrical hazard) from power source when

defrosting unit.

Defrosting

It is important to defrost and clean freezer

when ¼ to ½ inch of frost has accumulated.

Frost may tend to accumulate faster on upper

part of the freezer due to warm, moist air

entering the freezer when the door is opened.

Remove food and leave the door open when

defrosting the freezer.

• On upright models with a defrost

drain (Figure 1), remove drain plug on

the inside oor of the freezer by pulling

straight out. To access external drain tube

on models with a base panel, rst remove

the 2 screws from the base panel. Locate

the drain tube near the left center under

the freezer. Place a shallow pan under

the drain tube. Defrost water will drain

out. Check pan occasionally so water

does not overow. A ½ inch garden hose

adapter can be used to drain the freezer

directly into a oor drain. If your model

is not equipped with an adapter, one can

be purchased at most hardware stores.

Replace the drain plug when defrosting and

cleaning are completed. If the drain is left

open, warm air may enter freezer.

• On chest models with a defrost drain,

place a shallow pan beneath the drain

outlet (Figure 2). A ½ inch garden hose

adapter can be used to drain the freezer

directly into a oor drain (Figure 3). If your

model is not equipped with an adapter, one

can be purchased at most hardware stores.

Pull out the drain plug inside the freezer,

and pull off the outside defrost drain plug

(Figure 4).

Figure 1

Drain Pan

Drain Tube

Defrost Drain

Figure 2

CARE AND CLEANING

Hose

Adaptor

Defrost

Drain

Plug

Figure 3

Drain

Plug

Figure 4

• Defrost water will drain out. Check pan

occasionally so water does not overow.

Replace the drain plugs when defrosting

is completed.

• On models without a defrost drain, place

towels or newspapers on the freezer bottom

to catch the frost. The frost will loosen and

fall. Remove towels and/or newspapers.

• If the frost is soft, remove it by using a

plastic scraper. If the frost is glazed and

hard, ll deep pans with hot water and

place them on the freezer bottom. Close the

freezer door. Frost should soften in about 15

minutes. Repeat this procedure if necessary.

Cleaning the Inside

After defrosting, wash inside surfaces of the

unit with a solution of 2 tbsp. (25 g) of baking

soda in 1 qt. (1 l) warm water. Rinse and dry.

Wring excess water out of the sponge or cloth

when cleaning in the area of the controls, or

any electrical parts.

Wash the removable parts with the baking soda

solution mentioned above, or mild detergent

and warm water. Rinse and dry. Never use

metallic scouring pads, brushes, abrasive

cleaners, or alkaline solutions on any surface.

Do not wash removable parts in a dishwasher.

Cleaning the Outside

Wash the cabinet with warm water and mild

liquid detergent. Rinse well and wipe dry with

a clean soft cloth. Replace parts and food.

WARNING

If leaving door open while on vacation, make

certain that children cannot get into the

appliance and become entrapped.

WARNING

Do not open door unnecessarily if unit is off

for several hours.

Vacation and Moving Tips

Short Vacations: Leave the appliance

operating during vacations of less than 3

weeks.

Long Vacations: If the unit will not be

used for several months, remove all food and

unplug the power cord. Clean and dry the

interior thoroughly. Leave the freezer door

open slightly, blocking it open if necessary, to

prevent odor and mold growth.

Moving: Disconnect the power cord plug

from the wall outlet. Remove food, defrost,

and then clean the appliance. Secure all loose

items such as base panel, baskets, and shelves

by taping them securely in place to prevent

damage. In the moving vehicle, secure the unit

in an upright position, and secure to prevent

movement. Also protect outside of unit with a

blanket, or similar item.

Do not use razor blades or other sharp

instruments, which can scratch the appliance

surface when removing adhesive labels. Any

glue left from the tape can be removed with

a mixture of warm water and mild detergent,

or touch the residue with the sticky side of the

tape already removed. DO NOT REMOVE THE

SERIAL PLATE.

If a power failure occurs, frozen foods will stay frozen for over 2 days (upright/convertible) or

3 days (chest) if the appliance is kept closed*. If the power failure continues, pack seven or eight

pounds of dry ice into the unit every 24 hours. Look in the Yellow Pages under "Dry Ice," "Dairies,"

or "Ice Cream Manufacturers" for local dry ice suppliers. Always wear gloves and use caution when

handling dry ice.

If the appliance has stopped operating,

see "Appliance does not run" in the BEFORE YOU CALL section of this manual. If you cannot

solve the problem, call an authorized servicer immediately.

If the appliance remains off for several hours, follow the directions above for the use of

dry ice during a power failure. If necessary, take the food to a local locker plant until the unit is

ready to operate. Look in the Yellow Pages under "Frozen Food Locker Plants."

*Average cabinet temperature as tested per AHAM standard HRF-1-2007 Section 7.9 at 70º with door

remaining closed.

POWER/

FREEZER FAILURE

BEFORE YOU CALL

PROBLEM CAUSE CORRECTION

APPLIANCE OPERATION

Appliance

does not run.

• Appliance is plugged into a

circuit that has a ground

fault interrupt.

• Temperature Control is in

the OFF position or POWER

OFF position.

• Appliance may not be

plugged in or plug is loose.

• Hose fuse blown or tripped

circuit breaker.

• Power outage

• Use another circuit. If you are unsure

about the outlet, have it checked by a

certied technician.

• See Setting the Temperature

Control section.

• Ensure plug is tightly pushed into outlet.

• Check/replace fuse with a 15-amp time-

delay fuse. Reset circuit breaker.

• Check house lights. Call local electric company.

1-866-312-2117 (United States)

1-800-668-4606 (Canada)

Before calling for service, review this list. It may save you time and expense. This list includes com-

mon occurrences that are not the result of defective workmanship or materials in this appliance.

PROBLEM CAUSE CORRECTION

Appliance

runs too much

or too long.

• Room or outside weather

is hot.

• Appliance has recently

been disconnected for a

period of time.

• Large amounts of warm

or hot food have been

stored recently.

• Door is opened too fre-

quently or too long.

• Door may be slightly open.

• Temperature control is set

too low.

• Gasket is dirty, worn,

cracked, or poorly tted.

• It’s normal for the appliance to work lon-

ger under these conditions.

• It takes 4 hours for the appliance to cool

down completely.

• Warm food will cause appliance to run

more until the desired temperature is

reached.

• Warm air entering the appliance causes it

to run more. Open door less often.

• Ensure door is tightly closed.

• Turn control knob to a warmer setting. Allow

several hours for the temperature to stabilize.

• Clean or change gasket. Leaks in door seal

will cause appliance to run longer in order

to maintain desired temperatures.

Pressing the “-”

or “+” buttons

on the control

panel does

not change the

set points.

• Verify the control panel

is not locked or in

Sabbath Mode.

• To unlock, press and hold “Set” button for

3 seconds; to exit Sabbath Mode press and

hold “Set” and “Options” for 5 seconds.

APPLIANCE TEMPERATURES

Interior tem-

perature is

too cold.

• Control is set too low.

• The appliance is in Quick

Freeze mode.

• Set control to a warmer setting. Allow sev-

eral hours for temperature to stabilize.

• Exit Quick Freeze mode by entering into

the options menu on the control panel and

pressing the “set” button once the indicator is

highlighted next to “Quick Freeze”.

Temperature

inside appli-

ance is

too warm.

• Control is set too warm.

• Door is opened too fre-

quently or too long.

• Door may not be

seating properly.

• Large amounts of warm

or hot food has been

stored recently.

• Appliance has recently

been disconnected for a

period of time.

• Set fresh food control to a colder setting. Al-

low several hours for temperature to stabilize.

• Warm air entering the appliance causes it

to run more Open door less often.

• See “DOOR PROBLEMS” section.

• Warm food will cause appliance to run

more until the desired temperature is

reached.

• Appliance requires 4 hours to cool

down completely.

External tem-

perature is

too warm.

• The external walls can be

as much as 30ºF warmer

than room temperature.

• This is normal while the compressor works

to transfer heat from inside the cabinet.

SOUND AND NOISE

Louder sound

levels when

appliance is on.

• Modern appliances have

increased storage capacity

and more stable tempera-

tures. They require a high

efciency compressor.

• This is normal. When the surrounding

noise is low, you might hear the compres-

sor running while it cools the interior.

BEFORE YOU CALL

PROBLEM CAUSE CORRECTION

Longer sound

levels when

compressor

comes on.

• Appliance operates at

higher pressures during

the start of the ON cycle.

• This is normal. Sound will level off or dis-

appear as appliance continues to run.

Popping or

cracking sound

when compres-

sor comes on.

• Metal parts undergo ex-

pansion and contraction, as

in hot water pipes.

• This is normal. Sound will level off or dis-

appear as the appliance continues to run.

Bubbling

or gurgling

sound, like

water boiling.

• Refrigerant (used to cool

the appliance) is circulating

throughout the system.

• This is normal.

Vibrating or

rattling noise.

• Appliance is not level. It

rocks on the oor when it

is moved slightly.

• Floor is uneven or weak.

Appliance rocks on oor

when it is moved slightly.

• Appliance is touching

the wall.

• Level the unit. Refer to ”Leveling” in the

INSTALLATION Section.

• Ensure oor can adequately support the ap-

pliance. Level the appliance by putting wood

or metal shims under part of the appliance.

• Re-level or move the appliance slightly. Refer

to “Leveling” in the INSTALLATION Section.

The alarm

is sounding

from the con-

trol panel

• Look on the control panel

to determine which indica-

tor light is on (High Temp,

Power Fail, or Door Ajar)

• Press the “set” button to acknowledge the

alarm or close the door if the door ajar

indicator is shown.

WATER/MOISTURE/FROST INSIDE APPLIANCE

Moisture forms

on inside walls.

• Weather is hot and humid.

• Door may not be

seating properly.

• Door is opened too often

or too long.

• The rate of frost buildup and internal

sweating increases. This is normal.

• See “DOOR PROBLEMS”.

• Open door less often.

WATER/MOISTURE/FROST OUTSIDE APPLIANCE

Moisture forms

on outside.

• Door may not be seating

properly, causing cold air

from inside to meet warm

air from outside.

• See “DOOR PROBLEMS”.

ODOR IN APPLIANCE

Odor in

appliance.

• Interior needs to be cleaned.

• Foods with strong odors

are in the appliance.

• Clean interior with sponge, warm water,

and baking soda.

• Cover the food tightly.

DOOR PROBLEMS

Door will

not close.

• Appliance is not level. It

rocks on the oor when it

is moved slightly.

• Floor is uneven or weak.

Appliance rocks on oor

when it is moved slightly.

• This condition can force the cabinet out

of square and misalign the door. Refer to

“Leveling” in the INSTALLATION Section.

• Level the oor by using wood or metal

shims under the appliance or brace oor

supporting the appliance.

LIGHT BULB IS NOT ON

Power Avail-

able Light is

not on

• LED may be burned out.

• No electric current is

reaching the appliance.

• The door has been left open

for more than 5 minutes.

• Contact a qualied service dealer.

• See “Appliance does not run” in

“APPLIANCE OPERATION”.

• Close the door.

WHITE-WESTINGHOUSE APPLIANCE

WARRANTY INFORMATION

Your appliance is covered by a one year limited warranty. For one year from your original date of

purchase, Electrolux will pay all costs for repairing or replacing any parts of this appliance that prove

to be defective in materials or workmanship when such appliance is installed, used and maintained in

accordance with the provided instructions.

Exclusions

If You Need Service

This warranty does not cover the following:

1. Products with original serial numbers that have been removed, altered or cannot be readily determined.

2. Pr

oduct that has been transferred from its original owner to another party or removed

outside

the

USA or Canada.

3. R

ust on the interior or exterior of the unit.

4. Products purchased “as-is” are not covered by this warranty.

5. F

ood loss due to any refrigerator or freezer failures.

6. Products used in a commercial setting.

7. Service calls which do not involve malfunction or defects in materials or workmanship, or for appliances

not in ordinary household use or used other than in accordance with the provided instructions.

8. Service calls to correct the installation of your appliance or to instruct you how to use your appliance.

9. Expenses

for making the appliance accessible for servicing, such as removal of trim, cupboards,

shelves, etc., which are not a part of the appliance when it is shipped from the factory.

10.

Servicecallstorepairorreplaceappliancelightbulbs,airlters,waterlters,other

consumables, or knobs, handles, or other cosmetic parts.

11. Surcharges including, but not limited to, any after hour, weekend, or holiday service calls, tolls, ferry

trip charges, or mileage expense for service calls to remote areas, including the state of Alaska.

12. Damagestothenishofapplianceorhomeincurredduringinstallation,includingbutnot

limitedtooors,cabinets,walls,etc.

13. Damages caused by: services performed by unauthorized service companies; use of parts other than

genuine Electrolux parts or parts obtained from persons other than authorized service companies; or

externalcausessuchasabuse,misuse,inadequatepowersupply,accidents,res,oractsofGod.

DISCLAIMER OF IMPLIED WARRANTIES; LIMITATION OF REMEDIES

CUSTOMER’S SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT

REPAIR OR REPLACEMENT AS PROVIDED HEREIN. CLAIMS BASED ON IMPLIED WARRANTIES,

INCLUDINGWARRANTIESOFMERCHANTABILITYORFITNESSFORAPARTICULARPURPOSE,ARE

LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW, BUT NOT LESS THAN ONE

YEAR.ELECTROLUXSHALLNOTBELIABLEFORCONSEQUENTIALORINCIDENTALDAMAGESSUCH

ASPROPERTYDAMAGEANDINCIDENTALEXPENSESRESULTINGFROMANYBREACHOFTHIS

WRITTEN LIMITED WARRANTY OR ANY IMPLIED WARRANTY. SOME STATES AND PROVINCES DO

NOTALLOWTHEEXCLUSIONORLIMITATIONOFINCIDENTALORCONSEQUENTIALDAMAGES,

OR LIMITATIONS ON THE DURATION OF IMPLIED WARRANTIES, SO THESE LIMITATIONS OR

EXCLUSIONSMAYNOTAPPLYTOYOU.THISWRITTENWARRANTYGIVESYOUSPECIFICLEGAL

RIGHTS.YOUMAYALSOHAVEOTHERRIGHTSTHATVARYFROMSTATETOSTATE.

This warranty only applies in the USA and Canada. In the USA, your appliance is warranted by

Electrolux Major Appliances North America, a division of Electrolux Home Products, Inc. In Canada,

your appliance is warranted by Electrolux Canada Corp. Electrolux authorizes no person to change

or add to any obligations under this warranty. Obligations for service and parts under this warranty

mustbeperformedbyElectroluxoranauthorizedservicecompany.Productfeaturesorspecications

as described or illustrated are subject to change without notice.

Keep your receipt, delivery slip, or some other appropriate payment record to establish the warranty

period should service be required. If service is performed, it is in your best interest to obtain and

keep all receipts. Service under this warranty must be obtained by contacting Electrolux at the

addresses or phone numbers below.

USA

1.866.312.2117

Electrolux Major Appliances

North America

10200 David Taylor Drive

Charlotte, NC 28262

Canada

1.800.668.4606

Electrolux Canada Corp.

5855 Terry Fox Way

Mississauga, Ontario, Canada

L5V 3E4

TABLE DES MATIÈRES

Tout à propos de

l’utilisation et l’entretien

de votre congélateur

A04704301 (août 2015)

Enregistrement de votre appareil..................2

Mesures de sécurité importantes .................2

Étapes initiales ...........................................4

Réglage de la commande de température ....7

Caractéristiques facultatives ........................8

Conseils pour économiser l’énergie ..............9

Entretien et nettoyage...... ..........................9

Panne de courant/de congélateur................11

Avant d’appeler. .......................................11

Garantie sur les gros appareils électroménagers...14

ENREGISTREMENT DE

VOTRE APPAREIL

Veuillez lire et conserver

ces instructions

Ce guide d’utilisation et d’entretien contient

des instructions d’utilisation spéciques à

votre modèle. N’utilisez votre appareil à vin

qu’en observant les instructions présentées

dans ce guide. Ces instructions ne traitent

pas de toutes les conditions d’utilisation et

situations possibles. Il faut user de bon sens

et de prudence durant l’installation, l’emploi et

l’entretien de tout appareil électroménager.

Notez les numéros de modèle et

de série de votre appareil

Notez les numéros de modèle et de série dans

l’espace ci-dessous.

Numéro de modèle :

Numéro de série :

Date d’achat :

Dénitions

Voici le symbole d’avertissement concernant

la sécurité. Il est utilisé pour vous avertir des

risques de blessures potentiels. Respectez tous

les messages qui suivent ce symbole an de

prévenir les blessures ou la mort.

AVERTISSEMENT

Veuillez lire ces instructions au complet

avant d’utiliser l’unité.

DANGER

La mention DANGER indique un risque

imminent qui causera la mort ou de graves

blessures, s’il n’est pas évité.

AVERTISSEMENT

La mention AVERTISSEMENT indique une

situation potentiellement dangereuse qui, si

elle n’est pas évitée, pourrait entraîner des

blessures graves ou même la mort.

ATTENTION

La mention ATTENTION signale la présence

d’une situation potentiellement dangereuse

susceptible de causer des blessures

mineures ou moyennement graves si elle

’est pas évitée.

IMPORTANT

IMPORTANT - Cette mention précède

des renseignements importants relatifs

à l’installation, au fonctionnement ou à

l’entretien. Toutefois, ceux-ci n’impliquent

aucune notion de danger.

Enregistrez votre produit

La CARTE

D’ENREGISTREMENT DU

PRODUIT pré-adressée (il-

lustrée cidessus) doit être

complètement remplie,

signée et retournée à

l’adresse fournie.

AVERTISSEMENT

Sécurité des enfants

• Détruisez le carton, les sacs en plastique

et tout matériau d’emballage externe im-

médiatement après le déballage du appa-

reil. Les enfants ne devraient jamais jouer

avec ces articles. Les boîtes recouvertes

de tapis, de couvertures, de feuilles de

plastique et de pellicules étirables peuvent

devenir étanches à l’air et rapidement

provoquer la suffocation.

• Les glacières, l’appareil jetés au rebut

représentent un attrait dangereux pour

les enfants.

• Enlevez la porte ou les portes de tout

appareil qui n’est pas utilisé, même s’il est

mis au rebut.

MESURES DE SÉCURITÉ

IMPORTANTES

AVERTISSEMENT

Pour votre sécurité

• N’entreposez pas et n’utilisez pas

d’essence ni aucun autre liquide inam-

mable à proximité de cet appareil ou de

tout autre appareil. Lisez les étiquettes

d’avertissement du produit concernant

l’inammabilité et autres dangers.

• Ne pas faire fonctionner l’appareil en

présence de vapeurs explosives.

• Enlevez et jetez les cales d’espacement

utilisées pour immobiliser les clayettes

durant l’expédition. Les enfants peuvent

s’étouffer avec les petits objets.

• Enlevez toutes les agrafes du carton. Les

agrafes peuvent causer de graves coupures

et endommager les nitions si elles entrent en

contact avec d’autres appareils ou meubles.

MESURES DE SÉCURITÉ IMPORTANTES

AVERTISSEMENT

Mise au rebut instructions avant

d’utiliser électroménager

Dangers d’enfermement des enfants

Les risques d’enfermement et de suffocation

des enfants ne sont pas des problèmes

dépassés. L’appareil abandonnés ou mis au

rebut sont dangereux, même si ce n’est «

que pour quelques jours ». Si vous désirez

vous défaire de votre vieux électroménager,

veuillez suivre les instructions ci-dessous

an d’aider à prévenir les accidents.

Nous encourageons fortement les méthodes

responsables de recyclage et de mise au

rebut des appareils. Vériez auprès de votre

entreprise de services publics ou visitez le

site www.energystar.gov/recycle pour de

plus amples renseignements sur la manière

de recycler votre vieux électroménager.

Avant de mettre votre

vieil appareil au rebut :

• Retirez la porte/

le couvercle.

• Laissez les clayettes

en place pour que les enfants ne puissent

pas grimper facilement à l’intérieur.

• Demandez à un technicien qualié de

vidanger le uide frigorigène.

Prise avec mise à la terre

Cordon électrique muni

d’une fiche à trois broches

avec mise à la terre

Ne coupez pas,

n'enlevez pas et ne

mettez pas hors circuit

la broche de mise à la

terre de cette fiche.

AVERTISSEMENT

Éviter tout risque de feu ou de choc

électrique. Ne pas utiliser de cordon

prolongateur ni che d’adaptation. N’enlever

aucune des broches du cordon.

AVERTISSEMENT

Information concernant l’électricité

Vous devez suivre ces directives pour que

les mécanismes de sécurité de votre appareil

fonctionnent correctement.

• Reportez-vous à la plaque signalétique

pour connaître les caractéristiques nomi-

nales du courant. Le cordon de appareil

est muni d’une che à trois broches avec

mise à la terre pour éviter les décharges

électriques. Elle doit être branchée

directement dans une prise murale mise à

la terre, à trois alvéoles, protégée par un

coupe-circuit ou un fusible à action retar-

dée de 15 A. La prise doit être installée

conformément aux codes et règlements

locaux. Consultez un électricien qualié.

Les prises avec un mise à terre fault circuit

interrupteur NE SONT PAS RECOMMEN-

DÉES. N’utilisez pas de cordon prolonga-

teur ni de che d’adaptation.

• Si le cordon d’alimentation est endomma-

gé, il doit être remplacé par un technicien

en entretien et réparation autorisé an

d’éviter tout accident.

• Ne débranchez jamais l’appareil en tirant

sur le cordon d’alimentation. Tenez tou-

jours la che fermement en la tirant en

ligne droite pour la retirer de la prise an

d’éviter d’endommager le cordon.

• Pour éviter les chocs électriques, débran-

chez l’appareil avant de le nettoyer ou de

remplacer une ampoule.

• Si la tension varie de 10% ou plus, les

performances de votre appareil risquent

d’en être affectées, et le moteur endom-

magé. Un tel dommage n’est pas couvert

par la garantie. Si vous soupçonnez que la

tension est élevée ou basse, communiquez

avec votre compagnie d’électricité.

• Pour éviter que l’appareil ne soit acciden-

tellement débranché, ne le branchez pas

dans une prise commandée par un inter-

rupteur mural ou un cordon de tirage.

• Ne pincez pas, ne tordez pas, ne nouez

pas le cordon d’alimentation.

AVERTISSEMENT

Autres précautions

• Pour dégivrer l’appareil, débranchez toujours l’unité.

• Ne débranchez jamais l’unité en tirant sur le cordon. Saisissez toujours bien la che et

sortez-la de la prise en tirant droit vers vous.

• Placer la commande sur «OFF» (ARÊT), vous ne coupez pas l’alimentation des composants

électriques, mais du compresseur seulement.



REMARQUE

Il est très important que votre appareil soit mis de niveau pour fonctionner correctement. Si

l’appareil n’est pas mis de niveau lors de l’installation, le couvercle pourrait être désaligné et

ne pas se fermer correctement et hermétiquement, ce qui pourrait occasionner des problèmes

de refroidissement, de givre ou d’humidité.



REMARQUE

Les parois externes du appareil peuvent devenir chaudes

lorsque le compresseur fonctionne pour transférer la chaleur

présente à l’intérieur. La température des parois peut

atteindre jusqu’à 15 °C (30 °F) de plus que la température

ambiante. Pour cette raison, il est particulièrement important

dans les climats plus chauds de laisser assez d’espace pour

que l’air circule autour de votre appareil.

Mise de niveau

Tous les coins inférieurs du appareil doivent reposer fermement sur un plancher solide. Le

plancher doit être assez solide pour supporter le poids d’un appareil rempli à pleine capacité.

Ce Manuel d’utilisation et d’entretien contient des instructions d’utilisation spéciques à

votre modèle. N’utilisez l’unité que conformément aux instructions présentées dans ce Guide

d’utilisation et d’entretien. Avant de mettre l’unité en marche, suivez ces premières

étapes importantes :

Emplacement

Choisissez un emplacement près d’une prise électrique avec mise à

la terre. N’utilisez pas de rallonge électrique ou de che d’adaptation.

Pour une utilisation plus efcace du appareil, placez-le à un

endroit où la température ne dépassera jamais 43 °C (110 °F).

Des températures de 0 °C (32 °F) ou moins ne nuiront PAS au

fonctionnement du appareil. Il n’est pas recommandé d’ajouter

des générateurs de chaleur additionnels pour le compresseur.

Allouez sufsamment d’espace autour de l’appareil pour

permettre une bonne circulation d’air. Laissez un espace de 75

mm (3 pouces) autour du congélateur an de permettre à l’air de

circuler de façon adéquate.

ATTENTION

Pour permettre à la porte de fermer correctement et de

manière hermétique, NE LAISSEZ PAS DÉPASSER les

emballages des aliments de l’avant des clayettes.

3 po

(7,5 cm)

3 po (7,5 cm)

3 po

(7,5 cm)

Espace de 3 po

(7,5 cm)

Pour mettre à niveau les appareils horizontaux :

Après avoir jeté les vis de mise en caisse, utilisez un niveau de charpentier pour mettre l’appareil

à niveau de l’avant vers l’arrière. Réglez d’½ bulle plus haut les pieds de mise à niveau en

plastique situés à l’avant pour que la porte se referme facilement quand elle est entrouverte.

Repositionner le panier de niveau intermédiaire (certains modèles) :

1. Pour enlever le panier suspendu, pousser le dessous avant du panier vers le haut pour le

relâcher de sa tringle.

2. Rouler le devant sous l’étagère, puis glisser le panier suspendu vers l’avant pour le

relâcher de sa tringle arrière.

3. Pour enlever l’œillet d’étagère, le glisser loin du mur, puis le tirer de la tringle.

4. Répéter les étapes 1 à 3 pour l’autre côté.

7,5 cm (3 po)

7,5 cm

(3 po)

Installation

ÉTAPES INITIALES

Pour mettre à niveau les appareils verticaux :

Au besoin, ajoutez des cales en métal ou en bois entre les

pieds de l’appareil et le plancher.

ÉTAPES INITIALES

1. Placez le panier sur une surface solide

et plate.

2. Avec le côté étroit de la bride de

la poignée sur l’intérieur du panier,

accrochez la bride de poignée à la zone

enfoncée dans le panier.

Pour installer les brides de poignée

au panier :

3. Lorsque la surface intérieure clique

bien en place, continuez le processus

en bougeant la bride de la poignée

légèrement vers l’extérieur et en

appuyant fermement pour cliquer en

Dépose de la porte (modèles verticaux)

S’il faut enlever la porte debrancher l’unite.

1. Poser doucement l’unité sur sa partie

arrière, sur un tapis ou une couverture.

2. Enlever les 2 vis du panneau inférieur et

le panneau lui-même.

3. Pour débrancher le connecteur, si exigé,

retenir le connecteur de la caisse en

place, puis sortir le connecteur de la

porte. Si équipé, dégagez la retenue de

faisceau du cabinet.

4. Retirer les 4 vis de charnière inférieure.

5. Retirer le couvre-charnière supérieur

en plastique.

6. Enlever les 2 vis de la charnière supérieure.

7. Enlever la charnière supérieure de

la caisse.

8. Enlever la porte et la charnière inférieure

de la caisse.

9. Pour remettre la porte en place,

procéder inversement et bien serrer

toutes les vis pour éviter que les

charnières ne glissent. S’assurer que

le faisceau de porte est acheminé

comme indiqué et que la bride est bien

assujettie au cabinet.

Vis du inférieur

Vis de

charnière

Fil

Connecteur

de porte

Connecteur

de caisse

Harnais

de retenue

L’enlevement de couvercle

(modèles horizontaux)

Voir des instructions sur l’etiquette de gond.

Debrancher l’unite.

5. La clayette installée, appuyer vers

le bas sur les 2

œillets d’étagère

de la tringle ancrée

dans le mur de

l’appareil (à l’arrière

seulement).

S’assurer que

l’extrémité saillante

des œillets d’étagère

pointe vers

l’extérieur du mur.

6. Pousser les œillets

d’étagère sur la

tringle jusqu’à

ce qu’ils soient

installés fermement.

7. Faire glisser les

œillets d’étagère

dans les œillets

déjà en place dans

le mur de l’appareil

jusqu’à ce qu’ils

afeurent le mur.

8. Diriger le panier

suspendu en dessous de l’étagère tout

en insérant le bout fendu du support sur

la tringle d’étagère arrière.

9. Tourner le panier suspendu de façon à

ce qu’on puisse en

passer le devant

par-dessus la tringle

avant. Glisser

vers l’avant pour

passer le devant du

panier par-dessus

la tringle avant.

Appuyer sur le

support jusqu’à ce

qu’il clique en place.

place sur la surface

extérieure. Si installé

incorrectement, la

bride de la poignée ne

reposera pas à plat.



REMARQUE

Votre appareil peut avoir certaines des

caractéristiques énumérées ci-dessous,

ou encore toutes celles-ci. Apprenez à les

connaître et familiarisez-vous avec leur

utilisation et leur entretien.

OFF

ALARM

DEMO

HRS

POWER FAILHIGH TEMP

DOOR AJAR

ºC

REFRIGERATOR

FREEZER

ºF

quick freeze

power off

exit

control lock

PRESS

& HOLD

Alarme électronique temp.

Si un mauvais fonctionnement cause une

température non sécuritaire dans l’unité,

« high temp » s’afchera sur le panneau de

commande et l’alarme sonnera. Pour arrêter

l’alarme, appuyez sur le bouton « set » à côté

de l’indicateur « alarm off » sur l’afchage ou

appuyez sur n’importe quelle touche sur le

panneau de commande.

Congélation rapide

La Congélation rapide peut être activée

en entrant dans le menu options sur le

panneau de commande et en appuyant sur

le bouton « set » une fois que l’indicateur est

en surbrillance à côté de « quick freeze ».

L’appareil sera en mode de congélation rapide

pour 72 heures et afchera un ocon de neige

sur le panneau de commande pour indiquer

qu’il est en mode de congélation rapide.

Pour quitter le mode de congélation rapide,

entrez dans le menu options sur le panneau

de commande et appuyez sur le bouton « set

» une fois que l’indicateur est en surbrillance

à côté de « quick freeze »; le ocon de

neige disparaîtra alors du panneau de

commande. Ou la congélation rapide s’arrêtera

automatiquement après 72 heures.

Période de refroidissement

• An d’entreposer vos aliments de façon

sécuritaire , attendez 4 heures avant de

mettre vos aliments dans l’appareil pour qu’il

ait le temps de se refroidir complètement.

L’unité sera continuellement en marche

au cours des premières heures. Les

aliments déjà congelés peuvent être mis au

congélateur pendant les premières heures

de sa mise en marche. Il faut attendre 4

heures après la mise en marche du l’unité

pour y placer des aliments non congélés.

• Quand vous mettez des aliments au

appareil, ne placez pas plus de 1,3 kg

(3 lb) d’aliments non congélés à la fois

par pied carré d’espace de congélation.

Répartissez les aliments à congeler de

façon égale dans l’ensemble dul’unité. Il

n’est pas nécessaire de régler la commande

de température à une température plus

froide pendant le processus de congélation

des aliments.

Commande de température élec-

tromécanique (modèles horizontaux et

certains modèles de verticaux)

La commande de température est située à

l’intérieur du appareil (modèles verticaux)

ou sur la paroi extérieure gauche (modèles

horizontaux). L’appareil a été préréglé en

usine an d’assurer une température adéquate

de rangement de la nourriture. Vous pouvez

toutefois régler la commande de température

selon vos besoins. Si vous désirez une

température plus froide, tournez le bouton de

commande vers COLDEST (LE PLUS FROID)

puis attendez quelques heures, an que la

température se stabilise.

Commande électronique

de température (certains modèles)

La commande électronique de température est

située à l’extérieur de l’appareil. Le réglage par

défaut de la température est effectué en usine

an d’assurer une température d’entreposage

des aliments satisfaisante. Appuyez sur la

touche « + » du panneau de commande pour

augmenter la température ou sur la touche

« - » pour la baisser. Attendez quelques

heures pour permettre à la température de se

stabiliser entre les réglages.

RÉGLAGE DE LA COMMANDE DE TEMPÉRATURE

Page is loading ...

White Westinghouse WWFC18M4RC User guide

Brand: White Westinghouse

Model: WWFC18M4RC

Type: User guide

This manual is also suitable for

WWFC16M4RC

Download PDF

report

in other languages

français: White Westinghouse WWFC18M4RC Mode d'emploi
español: White Westinghouse WWFC18M4RC Guía del usuario

White Westinghouse WWFC18M4RC User guide

This manual is also suitable for

White Westinghouse WWFC18M4RC User guide

in other languages

Other documents