Grizzly Smoke Alarm G0690 User manual

Type
User manual

This manual is also suitable for

MODEL G0690/G0691
10" CABINET TABLE SAW
with RIVING KNIFE
OWNER'S MANUAL
Model G0691
Model G0690

WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.


This manual provides critical safety instructions on the proper setup,
operation, maintenance, and service of this machine/tool. Save this
document, refer to it often, and use it to instruct other operators.
Failure to read, understand and follow the instructions in this manual
may result in fire or serious personal injury—including amputation,
electrocution, or death.
The owner of this machine/tool is solely responsible for its safe use.
This responsibility includes but is not limited to proper installation in
a safe environment, personnel training and usage authorization,
proper inspection and maintenance, manual availability and compre-
hension, application of safety devices, cutting/sanding/grinding tool
integrity, and the usage of personal protective equipment.
The manufacturer will not be held liable for injury or property damage
from negligence, improper training, machine modifications or misuse.
3OMEDUSTCREATEDBYPOWERSANDINGSAWINGGRINDINGDRILLINGAND
OTHERCONSTRUCTIONACTIVITIESCONTAINSCHEMICALSKNOWNTOTHE3TATE
OF#ALIFORNIATOCAUSECANCERBIRTHDEFECTSOROTHERREPRODUCTIVE
HARM3OMEEXAMPLESOFTHESECHEMICALSARE
s ,EADFROMLEADBASEDPAINTS
s #RYSTALLINESILICAFROMBRICKSCEMENTANDOTHERMASONRYPRODUCTS
s !RSENICANDCHROMIUMFROMCHEMICALLYTREATEDLUMBER
9OURRISKFROMTHESEEXPOSURESVARIESDEPENDINGONHOWOFTENYOU
DOTHISTYPEOFWORK4OREDUCEYOUREXPOSURETOTHESECHEMICALS
7ORKINAWELLVENTILATEDAREAANDWORKWITHAPPROVEDSAFETYEQUIP
MENTSUCHASTHOSEDUSTMASKSTHATARESPECIALLYDESIGNEDTOFILTER
OUTMICROSCOPICPARTICLES
Table of Contents
INTRODUCTION ............................................... 2






SECTION 1: SAFETY ..................................... 10
 
 
 
 
 
SECTION 2: POWER SUPPLY ...................... 15
SECTION 3: SETUP ....................................... 17
 
 
 
 
 
 
 
 
 
 
 
 
 
SECTION 4: OPERATIONS ........................... 32
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
SECTION 5: SHOP MADE SAFETY
ACCESSORIES .............................................. 50
 
 
 
 
 
 
SECTION 6: AFTERMARKET ACCESSORIES
FROM GRIZZLY ............................................. 58
SECTION 7: MAINTENANCE ......................... 61
 
 
 
SECTION 8: SERVICE ................................... 63
 
 
 
 
 
 
 
 
SECTION 9: WIRING ...................................... 74
 
 
SECTION 10: PARTS ..................................... 76
 
 
 
 
 
 
 
 
WARRANTY AND RETURNS ........................ 89


INTRODUCTION

       


      



      
    




Machine Description
LZ hiVcY WZ]^cY djg bVX]^cZh# >[ ndj ]VkZ
VcnfjZhi^dch dg cZZY]Zae! jhZ i]Z^c[dgbVi^dc
WZadlidXdciVXijh#7Z[dgZXdciVXi^c\!eaZVhZ\Zi
i]ZhZg^Va cjbWZg VcYbVcj[VXijgZ YViZ d[ndjg
bVX]^cZ#I]^hl^aa]Zaejh]Zaendj[VhiZg#
<g^ooanIZX]c^XVaHjeedgi
&'%(AnXdb^c\BVaa8^gXaZ
BjcXn!E6&,,*+
E]dcZ/*,%*)+".++(
:bV^a/iZX]hjeedgi5\g^ooan#Xdb
LZlVcindjg[ZZYWVX`dci]^hbVcjVa#L]ViY^Y
ndj a^`Z VWdji ^i4 L]ZgZ XdjaY ^i WZ ^begdkZY4
EaZVhZiV`ZV[Zlb^cjiZhid\^kZjh[ZZYWVX`#
<g^ooan9dXjbZciVi^dcBVcV\Zg
E#D#7dm'%+.
7Zaa^c\]Vb!L6.-'',"'%+.
:bV^a/bVcjVah5\g^ooan#Xdb
Contact Info
LZVgZegdjYidd[[Zgi]^hbVcjVal^i]ndjgcZl
bVX]^cZ LZkZ bVYZ ZkZgn Z[[dgi id WZ ZmVXi
l^i] i]Z ^chigjXi^dch! heZX^[^XVi^dch! YgVl^c\h!
VcY e]did\gVe]h d[ i]Z bVX]^cZ lZ jhZY l]Zc
lg^i^c\i]^hbVcjVa#=dlZkZg!hdbZi^bZhlZhi^aa
bV`ZVcdXXVh^dcVab^hiV`Z#
6ahd!dl^c\id djgeda^Xnd[Xdci^cjdjh^begdkZ"
bZci!your machine may not exactly match the
manual#>[ndj[^cYi]^hidWZi]ZXVhZ!VcYi]ZY^["
[ZgZcXZWZilZZci]ZbVcjVaVcYbVX]^cZaZVkZh
ndj ^c YdjWi! X]ZX` djg lZWh^iZ [dg i]Z aViZhi
bVcjVajeYViZdgXVaaiZX]c^XVahjeedgi[dg]Zae#
7Z[dgZXVaa^c\![^cYi]ZbVcj[VXijgZYViZd[ndjg
bVX]^cZWnadd`^c\Vii]ZYViZhiVbeZY^cidi]Z
bVX]^cZ >9 aVWZa hZZ WZadl# I]^h l^aa ]Zae jh
YZiZgb^cZ ^[ i]Z bVcjVa kZgh^dc ndj gZXZ^kZY
bViX]Zhi]ZbVcj[VXijgZYViZd[ndjgbVX]^cZ#
;dgndjgXdckZc^ZcXZ!lZedhiVaaVkV^aVWaZbVc"
jVahVcYbVcjVajeYViZh[dg[gZZdcdjglZWh^iZ
Viwww.grizzly.com#6cnjeYViZhidndjgbdYZa
d[ bVX]^cZ l^aa WZ gZ[aZXiZY ^c i]ZhZ YdXjbZcih
VhhddcVhi]ZnVgZXdbeaZiZ#
BVcj[VXijgZ9ViZ
d[NdjgBVX]^cZ
Manual Accuracy


Figure 3. 
Identification



































The information contained herein is deemed accurate as of 3/7/2011 and represents our most recent product specifications.
Due to our ongoing improvement efforts, this information may not accurately describe items previously purchased.
PAGE 1 OF 3Model G0690
0$&+,1('$7$
6+((7
Customer Service #: (570) 546-9663 · To Order Call: (800) 523-4777 · Fax #: (800) 438-5901
02'(/*+39&$%,1(77$%/(6$::,7+
5,9,1*.1,)(
Product Dimensions:
Weight.............................................................................................................................................................. 507 lbs.
Width (side-to-side) x Depth (front-to-back) x Height........................................................................... 62 x 41 x 40 in.
Footprint (Length x Width)............................................................................................................................ 20 x 20 in.
Shipping Dimensions:
Carton #1
Type.............................................................................................................................. Cardboard/Wood Skids
Content................................................................................................................................................. Machine
Weight.................................................................................................................................................... 463 lbs.
Length x Width x Height............................................................................................................. 33 x 30 x 40 in.
Carton #2
Type................................................................................................................................................... Cardboard
Content..................................................................................................................................................... Fence
Weight...................................................................................................................................................... 27 lbs.
Length x Width x Height............................................................................................................... 42 x 17 x 7 in.
Carton #3
Type................................................................................................................................................... Cardboard
Content....................................................................................................................................................... Rails
Weight...................................................................................................................................................... 49 lbs.
Length x Width x Height................................................................................................................. 68 x 7 x 5 in.
Electrical:
Minimum Circuit Size.............................................................................................................................................. 20A
Switch...................................................................................................... Magnetic with Thermal Overload Protection
Switch Voltage...................................................................................................................................................... 220V
Cord Length......................................................................................................................................................... 6 feet
Cord Gauge................................................................................................................................................... 14 gauge
Plug Included........................................................................................................................................................... No
Recommended Plug/Outlet Type.......................................................................................................................... 6-20
Motors:
Main
Type.................................................................................................................. TEFC Capacitor Start Induction
Horsepower................................................................................................................................................ 3 HP
Voltage....................................................................................................................................................... 220V
Phase....................................................................................................................................................... Single
Amps......................................................................................................................................................... 12.8A
Speed................................................................................................................................................ 3450 RPM
Cycle......................................................................................................................................................... 60 Hz
Number of Speeds............................................................................................................................................ 1
Power Transfer ..................................................................................................................... Triple V-Belt Drive
Bearings....................................................................................................... Shielded and Permanently Sealed


The information contained herein is deemed accurate as of 3/7/2011 and represents our most recent product specifications.
Due to our ongoing improvement efforts, this information may not accurately describe items previously purchased.
PAGE 2 OF 3Model G0690
Main Specifications:
Blade Information
Maximum Blade Diameter......................................................................................................................... 10 in.
Maximum Width of Dado...................................................................................................................... 13/16 in.
Blade Tilt...................................................................................................................................... Left 0-45 deg.
Arbor Size................................................................................................................................................. 5/8 in.
Arbor Speed...................................................................................................................................... 4300 RPM
Arbor Bearings.......................................................................................... Sealed and Permanently Lubricated
Cutting Capacities
Maximum Depth of Cut At 90 Degrees.................................................................................................. 3-1/8 in.
Maximum Depth of Cut At 45 Degrees................................................................................................ 2-3/16 in.
Maximum Rip To Right of Blade-Standard.......................................................................................... 29-1/2 in.
Maximum Rip To Left of Blade.................................................................................................................. 12 in.
Table Information
Floor To Table Height................................................................................................................................ 34 in.
Table Size Width........................................................................................................................................ 20 in.
Table Size Depth....................................................................................................................................... 27 in.
Table Size Thickness............................................................................................................................ 1-1/2 in.
Table Size With Extension Wings Width.................................................................................................... 40 in.
Table Size With Extension Wings Depth................................................................................................... 27 in.
Table Size With Extension Wings Thickness......................................................................................... 1-1/2 in.
Distance Front of Table To Center Of Blade....................................................................................... 17-1/4 in.
Distance Front of Table To Blade At Maximum Cut............................................................................ 12-1/4 in.
Fence Information
Fence Type.................................................................................... Camlock T-Shaped Fence with HDPE Face
Fence Size Length..................................................................................................................................... 48 in.
Fence Size Width.................................................................................................................................. 4-1/8 in.
Fence Size Height................................................................................................................................. 2-1/2 in.
Fence Rail Type................................................................................................................. Square Steel Tubing
Fence Rail Length...................................................................................................................................... 62 in.
Fence Rail Width................................................................................................................................... 2-3/4 in.
Fence Rail Height........................................................................................................................................ 2 in.
Miter Gauge Information
Miter Gauge Slot Type.............................................................................................................................. T-Slot
Miter Gauge Slot Size Width..................................................................................................................... 3/4 in.
Miter Gauge Slot Size Height................................................................................................................... 3/8 in.
Construction
Table....................................................................................................................... Precision Ground Cast Iron
Wings...................................................................................................................... Precision Ground Cast Iron
Trunnions............................................................................................................................................. Cast Iron
Base....................................................................................................................................... Pre-Formed Steel
Body Assembly...................................................................................................................... Pre-Formed Steel
Fence Assembly................................................................................................... Steel with HDPE Side Plates
Rails........................................................................................................................................................... Steel
Miter Guage.................................................................................................................. Cast Iron with Steel Bar
Guard....................................................................................................................................... Steel and Plastic
Other Related Information
Paint........................................................................................................................................... Powder Coated
Number of Dust Ports....................................................................................................................................... 1
Dust Port Size.............................................................................................................................................. 4 in.


The information contained herein is deemed accurate as of 3/7/2011 and represents our most recent product specifications.
Due to our ongoing improvement efforts, this information may not accurately describe items previously purchased.
PAGE 3 OF 3Model G0690
Other Specifications:
ISO Factory .................................................................................................................................................. ISO 9001
Country Of Origin ............................................................................................................................................... China
Serial Number Location ............................................................................................................... ID Label on Cabinet
Assembly Time ................................................................................................................................................. 1 Hour
Features:
Leeson Motor
Precision Ground Cast Iron Table
Cast Iron Trunnions
4" Dust Port
T-Slot Miter Gauge
Riving Knife and Blade Guard
Camlock T-Shaped Fence with HDPE Face
Quick-Release Device for Changing Guard/Riving Knife
Powder Coated Paint
Standard and Dado Table Inserts
Quick Release Riving Knife
Quick Release Motor Guard
Quick Release Splitter Assembly
Easy Glide Fence System
Knurled Knobs for Adjusting Fence
Nylon Runners Inside Fence Head Assembly
T-Square Type Fence System
Recessed Screw Holding Table Insert


The information contained herein is deemed accurate as of 3/7/2011 and represents our most recent product specifications.
Due to our ongoing improvement efforts, this information may not accurately describe items previously purchased.
PAGE 1 OF 3Model G0691
0$&+,1('$7$
6+((7
Customer Service #: (570) 546-9663 · To Order Call: (800) 523-4777 · Fax #: (800) 438-5901
02'(/*+39&$%,1(77$%/(6$::,7+
/21*5$,/65,9,1*.1,)(
Product Dimensions:
Weight.............................................................................................................................................................. 546 lbs.
Width (side-to-side) x Depth (front-to-back) x Height........................................................................... 82 x 41 x 40 in.
Footprint (Length x Width)............................................................................................................................ 20 x 20 in.
Shipping Dimensions:
Carton #1
Type.............................................................................................................................. Cardboard/Wood Skids
Content................................................................................................................................................. Machine
Weight.................................................................................................................................................... 481 lbs.
Length x Width x Height............................................................................................................. 33 x 30 x 40 in.
Carton #2
Type................................................................................................................................................... Cardboard
Content..................................................................................................................................................... Fence
Weight...................................................................................................................................................... 27 lbs.
Length x Width x Height............................................................................................................... 42 x 17 x 7 in.
Carton #3
Type................................................................................................................................................... Cardboard
Content....................................................................................................................................................... Rails
Weight...................................................................................................................................................... 71 lbs.
Length x Width x Height................................................................................................................. 92 x 7 x 5 in.
Electrical:
Minimum Circuit Size.............................................................................................................................................. 20A
Switch...................................................................................................... Magnetic with Thermal Overload Protection
Switch Voltage...................................................................................................................................................... 220V
Cord Length............................................................................................................................................................ 6 ft.
Cord Gauge................................................................................................................................................... 14 gauge
Plug Included........................................................................................................................................................... No
Recommended Plug/Outlet Type.......................................................................................................................... 6-20
Motors:
Main
Type.................................................................................................................. TEFC Capacitor Start Induction
Horsepower................................................................................................................................................ 3 HP
Voltage....................................................................................................................................................... 220V
Phase....................................................................................................................................................... Single
Amps......................................................................................................................................................... 12.8A
Speed................................................................................................................................................ 3450 RPM
Cycle......................................................................................................................................................... 60 Hz
Number of Speeds............................................................................................................................................ 1
Power Transfer ..................................................................................................................... Triple V-Belt Drive
Bearings....................................................................................................... Shielded and Permanently Sealed


The information contained herein is deemed accurate as of 3/7/2011 and represents our most recent product specifications.
Due to our ongoing improvement efforts, this information may not accurately describe items previously purchased.
PAGE 2 OF 3Model G0691
Main Specifications:
Blade Information
Maximum Blade Diameter......................................................................................................................... 10 in.
Maximum Width of Dado...................................................................................................................... 13/16 in.
Blade Tilt...................................................................................................................................... Left 0-45 deg.
Arbor Size................................................................................................................................................. 5/8 in.
Arbor Speed...................................................................................................................................... 4300 RPM
Arbor Bearings.......................................................................................... Sealed and Permanently Lubricated
Cutting Capacities
Maximum Depth of Cut At 90 Degrees.................................................................................................. 3-1/8 in.
Maximum Depth of Cut At 45 Degrees................................................................................................ 2-3/16 in.
Maximum Rip To Right of Blade-Standard................................................................................................ 50 in.
Maximum Rip To Left of Blade.................................................................................................................. 12 in.
Table Information
Floor To Table Height................................................................................................................................ 34 in.
Table Size Width........................................................................................................................................ 20 in.
Table Size Depth....................................................................................................................................... 27 in.
Table Size Thickness............................................................................................................................ 1-1/2 in.
Table Size With Extension Wings Width............................................................................................. 74-3/4 in.
Distance Front of Table To Center Of Blade....................................................................................... 17-1/4 in.
Distance Front of Table To Blade At Maximum Cut............................................................................ 12-1/4 in.
Extension Table Size Width................................................................................................................. 34-3/4 in.
Fence Information
Fence Type.................................................................................... Camlock T-Shaped Fence with HDPE Face
Fence Size Length..................................................................................................................................... 48 in.
Fence Size Width.................................................................................................................................. 4-1/8 in.
Fence Size Height................................................................................................................................. 2-1/2 in.
Fence Rail Type................................................................................................................. Square Steel Tubing
Fence Rail Length...................................................................................................................................... 62 in.
Fence Rail Width................................................................................................................................... 2-3/4 in.
Fence Rail Height........................................................................................................................................ 2 in.
Miter Gauge Information
Miter Gauge Slot Type.............................................................................................................................. T-Slot
Miter Gauge Slot Size Width..................................................................................................................... 3/4 in.
Miter Gauge Slot Size Height................................................................................................................... 3/8 in.
Construction
Table....................................................................................................................... Precision Ground Cast Iron
Wings...................................................................................................................... Precision Ground Cast Iron
Trunnions............................................................................................................................................. Cast Iron
Base....................................................................................................................................... Pre-Formed Steel
Body Assembly...................................................................................................................... Pre-Formed Steel
Fence Assembly................................................................................................... Steel with HDPE Side Plates
Rails........................................................................................................................................................... Steel
Miter Guage.................................................................................................................. Cast Iron with Steel Bar
Guard....................................................................................................................................... Steel and Plastic
Other Related Information
Paint........................................................................................................................................... Powder Coated
Number of Dust Ports....................................................................................................................................... 1
Dust Port Size.............................................................................................................................................. 4 in.
Mobile Base........................................................................................................................................... G7314Z


The information contained herein is deemed accurate as of 3/7/2011 and represents our most recent product specifications.
Due to our ongoing improvement efforts, this information may not accurately describe items previously purchased.
PAGE 3 OF 3Model G0691
Other Specifications:
ISO Factory .................................................................................................................................................. ISO 9001
Country Of Origin ............................................................................................................................................... China
Warranty ............................................................................................................................................................ 1 Year
Serial Number Location ............................................................................................................... ID Label on Cabinet
Assembly Time ................................................................................................................................................. 1 Hour
Features:
Leeson Motor
Precision Ground Cast Iron Table
Cast Iron Trunnions
4" Dust Port
T-Slot Miter Gauge
Riving Knife and Blade Guard
Camlock T-Shaped Fence with HDPE Face
Quick-Release Device for Changing Guard/Riving Knife
Powder Coated Paint
Standard and Dado Table Inserts
Quick Release Riving Knife
Quick Release Motor Guard
Quick Release Splitter Assembly
Easy Glide Fence System
Knurled Knobs for Adjusting Fence
Nylon Runners Inside Fence Head Assembly
T-Square Type Fence System
Recessed Screw Holding Table Insert


For Your Own Safety, Read Instruction
Manual Before Operating this Machine
The purpose of safety symbols is to attract your attention to possible hazardous conditions.
This manual uses a series of symbols and signal words intended to convey the level of impor-
tance of the safety messages. The progression of symbols is described below. Remember that
safety messages by themselves do not eliminate danger and are not a substitute for proper
accident prevention measures.
WEARING PROPER APPAREL. 9d cdi lZVg
Xadi]^c\! VeeVgZa! dg _ZlZagn i]Vi XVc WZXdbZ
ZciVc\aZY ^c bdk^c\ eVgih# 6alVnh i^Z WVX` dg
XdkZgadc\]V^g# LZVgcdc"ha^e[ddilZVgidVkd^Y
VXX^YZciVaha^ehl]^X]XdjaYXVjhZVadhhd[ldg`"
e^ZXZXdcigda#
HEARING PROTECTION. 6alVnh lZVg ]ZVg"
^c\egdiZXi^dcl]Zc deZgVi^c\dgdWhZgk^^c\adjY
bVX]^cZgn# :miZcYZY ZmedhjgZ id i]^h cd^hZ
l^i]dji]ZVg^c\egdiZXi^dcXVc XVjhZ eZgbVcZci
]ZVg^c\adhh#
MENTAL ALERTNESS. 7Z bZciVaan VaZgi l]Zc
gjcc^c\ bVX]^cZgn# CZkZg deZgViZ jcYZg i]Z
^c[ajZcXZd[Ygj\hdgVaXd]da!l]Zci^gZY!dgl]Zc
Y^higVXiZY#
OWNER’S MANUAL. GZVY VcY jcYZghiVcY
i]^h dlcZg»h bVcjVa 7:;DG: jh^c\ bVX]^cZ#
JcigV^cZYjhZghXVcWZhZg^djhan]jgi#
EYE PROTECTION.6alVnhlZVg6CH>"VeegdkZY
hV[Zin\aVhhZhdgV[VXZh]^ZaYl]ZcdeZgVi^c\dg
dWhZgk^c\ bVX]^cZgn id gZYjXZ i]Z g^h` d[ ZnZ
^c_jgndgWa^cYcZhh[gdb[an^c\eVgi^XaZh#:kZgnYVn
ZnZ\aVhhZhVgZcdiVeegdkZYhV[Zin\aVhhZh#
HAZARDOUS DUST. 9jhi XgZViZY l]^aZ jh^c\
bVX]^cZgn bVn XVjhZ XVcXZg! W^gi] YZ[ZXih! dg
adc\"iZgb gZhe^gVidgn YVbV\Z# 7Z VlVgZ d[ Yjhi
]VoVgYhVhhdX^ViZYl^i]ZVX]ldg`e^ZXZbViZg^Va!
VcYValVnhlZVgVC>DH="VeegdkZYgZhe^gVidgid
gZYjXZndjgg^h`#
Indicates a potentially hazardous situation which, if not avoided,
MAY result in minor or moderate injury. It may also be used to alert
against unsafe practices.
Indicates a potentially hazardous situation which, if not avoided,
COULD result in death or serious injury.
Indicates an imminently hazardous situation which, if not avoided,
WILL result in death or serious injury.
This symbol is used to alert the user to useful information about
proper operation of the machine.
NOTICE
Safety Instructions for Machinery
SECTION 1: SAFETY


DISCONNECTING POWER SUPPLY.6alVnhY^h"
XdccZXi bVX]^cZ [gdb edlZg hjeean WZ[dgZ hZg"
k^X^c\! VY_jhi^c\! dg X]Vc\^c\ Xjii^c\ iddah W^ih!
WaVYZh!XjiiZgh! ZiX## BV`ZhjgZ hl^iX] ^h^c D;;
edh^i^dcWZ[dgZgZXdccZXi^c\idVkd^YVcjcZmeZXi"
ZYdgjc^ciZci^dcVahiVgi#
APPROVED OPERATION. JcigV^cZY deZgVidgh
XVc WZ hZg^djhan ]jgi Wn bVX]^cZgn# Dcan Vaadl
igV^cZY dg egdeZgan hjeZgk^hZY eZdeaZ id jhZ
bVX]^cZ# L]Zc bVX]^cZ ^h cdi WZ^c\ jhZY! Y^h"
XdccZXi edlZg! gZbdkZ hl^iX] `Znh! dg adX`"dji
bVX]^cZidegZkZcijcVji]dg^oZYjhZ·ZheZX^Vaan
VgdjcYX]^aYgZc#BV`Zldg`h]de`^Yegdd[
DANGEROUS ENVIRONMENTS. 9d cdi jhZ
bVX]^cZgn ^c lZi dg gV^cn adXVi^dch! XajiiZgZY
VgZVh! VgdjcY [aVbbVWaZh!dg ^c eddgan"a^i VgZVh#
@ZZe ldg` VgZV XaZVc! Ygn! VcY lZaa"a^\]iZY id
b^c^b^oZg^h`d[^c_jgn#
ONLY USE AS INTENDED. Dcan jhZ bVX]^cZ
[dg ^ih ^ciZcYZY ejgedhZ# CZkZg bdY^[n dg VaiZg
bVX]^cZ[dgVejgedhZcdi^ciZcYZYWni]ZbVcj"
[VXijgZgdghZg^djh^c_jgnbVngZhjai
USE RECOMMENDED ACCESSORIES.8dchjai
i]^hdlcZg»hbVcjVadgi]ZbVcj[VXijgZg[dggZX"
dbbZcYZY VXXZhhdg^Zh# Jh^c\ ^begdeZg VXXZh"
hdg^Zhl^aa^cXgZVhZi]Zg^h`d[hZg^djh^c_jgn#
CHILDREN & BYSTANDERS. @ZZe X]^aYgZc
VcYWnhiVcYZghVhV[ZY^hiVcXZVlVn[gdbldg`
VgZV#Hidejh^c\bVX]^cZ^[X]^aYgZcdgWnhiVcY"
ZghWZXdbZVY^higVXi^dc#
REMOVE ADJUSTING TOOLS. CZkZg aZVkZ
VY_jhibZciiddah!X]jX``Znh!lgZcX]Zh!ZiX#^cdg
dcbVX]^cZ·ZheZX^VaancZVgbdk^c\eVgih#KZg^[n
gZbdkVaWZ[dgZhiVgi^c\
SECURING WORKPIECE. L]Zc gZfj^gZY! jhZ
XaVbehdgk^hZhidhZXjgZldg`e^ZXZ#6 hZXjgZY
ldg`e^ZXZegdiZXih]VcYhVcY[gZZhWdi]d[i]Zb
iddeZgViZi]ZbVX]^cZ#
FEED DIRECTION.JcaZhhdi]Zgl^hZcdiZY![ZZY
ldg` V\V^chi i]Z gdiVi^dc d[ WaVYZh dg XjiiZgh#
;ZZY^c\^ci]ZhVbZY^gZXi^dcd[gdiVi^dcbVnejaa
ndjg]VcY^cidi]ZXji#
FORCING MACHINERY.9dcdi[dgXZbVX]^cZ#
>il^aa Yd i]Z _dWhV[Zg VcY WZiiZg Vii]Z gViZ [dg
l]^X]^ilVhYZh^\cZY#
GUARDS & COVERS. <jVgYh VcY XdkZgh XVc
egdiZXi ndj [gdb VXX^YZciVa XdciVXi l^i] bdk^c\
eVgih dg [an^c\ YZWg^h# BV`Z hjgZ i]Zn VgZ egde"
Zgan^chiVaaZY!jcYVbV\ZY! VcYldg`^c\XdggZXian
WZ[dgZjh^c\bVX]^cZ#
NEVER STAND ON MACHINE.HZg^djh^c_jgndg
VXX^YZciVa XdciVXi l^i] Xjii^c\ idda bVn dXXjg ^[
bVX]^cZ^hi^eeZY#BVX]^cZbVnWZYVbV\ZY#
STABLE MACHINE. JcZmeZXiZYbdkZbZciYjg"
^c\deZgVi^dch\gZVian^cXgZVhZhi]Zg^h`d[^c_jgn
VcY adhh d[ Xdcigda# KZg^[n bVX]^cZh VgZ hiVWaZ$
hZXjgZ VcY bdW^aZ WVhZh ^[ jhZY VgZ adX`ZY
WZ[dgZhiVgi^c\#
AWKWARD POSITIONS. @ZZe egdeZg [ddi^c\
VcYWVaVcXZViVaai^bZhl]ZcdeZgVi^c\bVX]^cZ#
9dcdidkZggZVX]6kd^YVl`lVgY]VcYedh^i^dch
i]Vi bV`Z ldg`e^ZXZ Xdcigda Y^[[^Xjai dg ^cXgZVhZ
i]Zg^h`d[VXX^YZciVa^c_jgn#
UNATTENDED OPERATION. CZkZg aZVkZ
bVX]^cZgjcc^c\l]^aZjcViiZcYZY#IjgcbVX]^cZ
OFFVcYZchjgZVaabdk^c\eVgihXdbeaZiZanhide
WZ[dgZlVa`^c\VlVn#
MAINTAIN WITH CARE.;daadlVaabV^ciZcVcXZ
^chigjXi^dch VcY ajWg^XVi^dc hX]ZYjaZh id `ZZe
bVX]^cZ^c\ddYldg`^c\XdcY^i^dc#6c^begdeZgan
bV^ciV^cZYbVX]^cZbVn^cXgZVhZi]Zg^h`d[hZg^"
djh^c_jgn#
CHECK DAMAGED PARTS. GZ\jaVgan ^cheZXi
bVX]^cZ [dg YVbV\ZY eVgih! addhZ Wdaih! b^h"
VY_jhiZY dg b^h"Va^\cZY eVgih! W^cY^c\! dg Vcn
di]Zg XdcY^i^dch i]Vi bVn V[[ZXi hV[Z deZgVi^dc#
6alVnhgZeV^gdggZeaVXZYVbV\ZYdgb^h"VY_jhi"
ZYeVgihWZ[dgZdeZgVi^c\bVX]^cZ#
EXPERIENCING DIFFICULTIES. >[ Vi Vcn i^bZ
ndj VgZ ZmeZg^ZcX^c\ Y^[[^Xjai^Zh eZg[dgb^c\ i]Z
^ciZcYZY deZgVi^dc! hide jh^c\ i]Z bVX]^cZ
8dciVXi djg IZX]c^XVa Hjeedgi 9ZeVgibZci Vi
*,%*)+".++(#


Additional Safety for Table Saws
HAND POSITIONING. CZkZg ejgedhZan idjX] V
hVl WaVYZ Yjg^c\ deZgVi^dc# 6alVnh `ZZe ]VcYh$
[^c\Zgh dji d[ i]Z WaVYZ eVi]0 eaVXZ i]Zb l]ZgZ
i]ZnXVccdiha^e^cidi]ZWaVYZVXX^YZciVaan#CZkZg
gZVX]VgdjcY!WZ]^cY!dgdkZgi]ZWaVYZ#IdjX]^c\
Vhe^cc^c\hVlWaVYZl^aaXVjhZhZg^djhaVXZgVi^dc
dgVbejiVi^dc^c_jg^Zh#
BLADE GUARD. JhZ i]Z WaVYZ \jVgY [dg Vaa
¸i]gdj\]Xjih¹[dgl]^X]^iXVcWZjhZY#6i]gdj\]
Xji^hVcdeZgVi^dcl]ZgZi]ZWaVYZXjihXdbeaZiZ"
an i]gdj\] i]Z ide d[ i]Z ldg`e^ZXZ# BV`Z hjgZ
i]ZWaVYZ\jVgY^h^chiVaaZYVcYVY_jhiZYXdggZXian0
egdbeian gZeV^g dg gZeaVXZ ^i ^[ YVbV\ZY# 6alVnh
gZ"^chiVaaWaVYZ\jVgY^bbZY^ViZanV[iZgdeZgVi^dch
i]Vi gZfj^gZ ^ih gZbdkVa# DeZgVi^c\ hVl l^i] i]Z
WaVYZ\jVgYgZbdkZY\gZVian^cXgZVhZhi]Zg^h`d[
hZkZgZaVXZgVi^dcdgVbejiVi^dc^c_jg^Zh[gdbVXX^"
YZciVaWaVYZXdciVXi#
RIVING KNIFE. JhZ i]Z g^k^c\ `c^[Z[dgVaa ¸cdc"
i]gdj\] Xjih¹ [dg l]^X] ^i XVc WZ jhZY# 6 cdc"
i]gdj\]Xji^hVcdeZgVi^dcl]ZgZi]ZWaVYZYdZh
cdi Xji i]gdj\] i]Z ide d[ i]Z ldg`e^ZXZ# BV`Z
hjgZi]Zg^k^c\`c^[Z^hVa^\cZYVcYedh^i^dcZYXdg"
gZXian0VcYegdbeiangZeV^gdggZeaVXZ^i^[YVbV\ZY#
Jh^c\i]Z g^k^c\`c^[Z^cXdggZXianl^aa^cXgZVhZi]Z
g^h`d[`^X`WVX`dgVXX^YZciVaWaVYZXdciVXi#
KICKBACK.@^X`WVX`dXXjghl]Zci]ZhVlWaVYZ
Z_ZXih i]Z ldg`e^ZXZ WVX` idlVgY i]Z deZgVidg#
@cdl]dlidgZYjXZi]Zg^h`d[`^X`WVX`!VcYaZVgc
]dlidegdiZXindjghZa[^[^iYdZhdXXjg#
FEEDING WORKPIECE. ;ZZY^c\ i]Z ldg`e^ZXZ
^cXdggZXian l^aa ^cXgZVhZ g^h` d[ `^X`WVX`# CZkZg
hiVgii]ZhVll^i]Vldg`e^ZXZidjX]^c\i]ZWaVYZ0
Vaadli]ZWaVYZidgZVX][jaaheZZYWZ[dgZXjii^c\#
Dcan [ZZY i]Z ldg`e^ZXZ V\V^chi i]Z Y^gZXi^dc d[
WaVYZ gdiVi^dc# 6alVnh jhZ hdbZ ineZ d[ \j^YZ
[ZcXZ!b^iZg\Vj\Z!ha^Y^c\ iVWaZ dg haZY! ZiX# id
[ZZYi]Zldg`e^ZXZ^cVhigV^\]ia^cZ#CZkZgWVX`V
ldg`e^ZXZdjid[VXjidgignidbdkZ^iWVX`lVgYh
dgh^YZlVnhV[iZghiVgi^c\VXji#;ZZYXjihVaai]Z
lVn i]gdj\] id XdbeaZi^dc# CZkZg eZg[dgb Vcn
deZgVi^dc¸[gZZ]VcY¹bV`^c\VXjil^i]djijh^c\V
[ZcXZ!b^iZg\Vj\Z!dgdi]Zg\j^YZ#
FENCE. BV`Z hjgZ i]Z [ZcXZ gZbV^ch egdeZgan
VY_jhiZYVcYeVgVaaZal^i] i]Z WaVYZ#6alVnhadX`
i]Z[ZcXZ^ceaVXZWZ[dgZjh^c\#Jh^c\dgVY_jhi^c\
i]Z[ZcXZ^cXdggZXianl^aa^cXgZVhZg^h`d[`^X`WVX`#
PUSH STICKS/BLOCKS.JhZejh]hi^X`hdgejh]
WadX`hl]ZcZkZgedhh^WaZid`ZZendjg]VcYh[Vg"
i]ZgVlVn[gdbi]ZWaVYZl]^aZXjii^c\0^ci]ZZkZci
d[VcVXX^YZcii]ZhZYZk^XZhl^aad[iZciV`ZYVb"
V\Zi]VildjaY]VkZ]VeeZcZYid]VcYh$[^c\Zgh#
CUT-OFF PIECES.CZkZgjhZndjg]VcYhidbdkZ
Xji"d[[hVlVn[gdbi]ZWaVYZl]^aZi]ZhVl^hgjc"
c^c\# >[ V Xji"d[[ WZXdbZh igVeeZY WZilZZc i]Z
WaVYZVcYiVWaZ^chZgi!ijgci]ZhVlOFFVcYVaadl
i]ZWaVYZidXdbeaZiZanhideWZ[dgZgZbdk^c\^i#
BLADE ADJUSTMENTS. 6Y_jhi^c\ i]Z WaVYZ
]Z^\]idgi^aiYjg^c\deZgVi^dc^cXgZVhZhi]Zg^h`d[
XgVh]^c\ i]Z WaVYZ VcY hZcY^c\ bZiVa [gV\bZcih
[an^c\l^i]YZVYan[dgXZVii]ZdeZgVidgdgWnhiVcY"
Zgh#DcanVY_jhii]ZWaVYZ]Z^\]iVcYi^ail]Zci]Z
WaVYZ^hXdbeaZiZanhideeZYVcYi]ZhVl^hOFF#
CHANGING BLADES. 6alVnh Y^hXdccZXi edlZg
WZ[dgZ X]Vc\^c\ WaVYZh# 8]Vc\^c\ WaVYZh l]^aZ
i]Z hVl ^h XdccZXiZY id edlZg \gZVian ^cXgZVhZh
i]Z^c_jgng^h`^[hVl^hVXX^YZciVaanedlZgZYje#
DAMAGED SAW BLADES. CZkZg jhZ WaVYZh
i]Vi ]VkZ WZZc YgdeeZY dg di]Zgl^hZ YVbV\ZY#
9VbV\ZYWaVYZhXVc[anVeVgiVcYhig^`Zi]ZdeZg"
Vidgl^i]h]VgYhd[bZiVa#
DADO AND RABBET OPERATIONS. 9D CDI
ViiZbei YVYd dg gVWWZi^c\ deZgVi^dch l^i]dji
[^ghi gZVY^c\ i]dhZ hZXi^dch ^c i]^h bVcjVa# 9VYd
VcYgVWWZi^c\deZgVi^dchgZfj^gZheZX^VaViiZci^dc
WZXVjhZ i]Zn bjhi WZ eZg[dgbZY l^i] i]Z WaVYZ
\jVgYgZbdkZY#
CUTTING CORRECT MATERIAL. CZkZg Xji
bViZg^Vahcdi^ciZcYZY[dgi]^hhVl0dcanXjicVijgVa
VcYbVc"bVYZlddY egdYjXih! aVb^cViZXdkZgZY
lddYegdYjXih!VcYhdbZeaVhi^Xh#8jii^c\bZiVa!
\aVhh!hidcZ!i^aZ!ZiX#^cXgZVhZhi]Zg^h`d[deZgVidg
^c_jgnYjZid`^X`WVX`dg[an^c\eVgi^XaZh#


Statistics show that most common acci-
dents among table saw users can be
linked to kickback. Kickback is typically
defined as the high-speed expulsion of
stock from the table saw toward its opera-
tor. In addition to the danger of the opera-
tor or others in the area being struck by
the flying stock, it is often the case that
the operator’s hands are pulled into the
blade during the kickback.
Below are tips to avoid the most common
causes of kickback:
 
      

 



        

       


        

         
      

       

       



      
       
        

        
      
    
     



      
      
     

Preventing Kickback
Even if you know how to prevent kickback, it
may still happen. Here are some tips to pro-
tect yourself if kickback DOES occur:
 


 


       
     

 
      
       
      

     

Protecting Yourself
From Kickback




VERY 
Arbor:       


Bevel Edge Cut:

      Page 42 

Blade Guard Assembly:


  Page 37

Crosscut:     
        
      Page 41 

Dado Blade:
Page 59
  DO NOT use a dado blade
larger than 8" in diameter on this saw! 


Dado Cut:      

     Page 42  

Featherboard:      
      
     Page 50  

Kerf:        
       

Kickback:       
   

Non-Through Cut:

Page 33
Parallel:
        


Perpendicular:


Push Stick:      
     
      
Page 53
Rabbet:

Page 45
Rip Cut:
         
Page 40
Riving Knife:     

     
Page 39
Straightedge:

Thin Kerf Blade: 


Through Cut:
      Page
33
Glossary of Terms


SECTION 2: POWER SUPPLY
Availability
7Z[dgZ^chiVaa^c\i]ZbVX]^cZ!Xdch^YZgi]ZVkV^a"
VW^a^inVcYegdm^b^ind[i]ZgZfj^gZYedlZghjeean
X^gXj^i# >[ Vc Zm^hi^c\ X^gXj^i YdZh cdi bZZi i]Z
gZfj^gZbZcih[dgi]^hbVX]^cZ!VcZlX^gXj^ibjhi
WZ ^chiVaaZY# Id b^c^b^oZ i]Z g^h` d[ ZaZXigdXj"
i^dc![^gZ!dgZfj^ebZciYVbV\Z!^chiVaaVi^dcldg`
VcYZaZXig^XVal^g^c\bjhiWZYdcZWnVfjVa^[^ZY
ZaZXig^X^Vc^cVXXdgYVcXZl^i]VaaVeea^XVWaZXdYZh
VcYhiVcYVgYh#
Electrocution, fire, or
equipment damage may
occur if machine is not
correctly grounded and
connected to the power
supply.
Full-Load Current Rating
I]Z [jaa"adVY XjggZci gVi^c\ ^h i]Z VbeZgV\Z V
bVX]^cZYgVlhVi&%%d[i]ZgViZYdjiejiedlZg#
Dc bVX]^cZh l^i] bjai^eaZ bdidgh! i]^h ^h i]Z
VbeZgV\ZYgVlcWni]ZaVg\Zhibdidgdghjbd[Vaa
bdidghVcYZaZXig^XVaYZk^XZhi]Vib^\]ideZgViZ
VidcZi^bZYjg^c\cdgbVadeZgVi^dch#
Full-Load Current Rating at 220V .. 12.8 Amps
I]Z[jaa"adVYXjggZci^hcdii]ZbVm^bjbVbdjci
d[Vbehi]Vii]ZbVX]^cZl^aaYgVl#>[i]ZbVX]^cZ
^hdkZgadVYZY!^il^aaYgVlVYY^i^dcVaVbehWZndcY
i]Z[jaa"adVYgVi^c\#
>[i]ZbVX]^cZ^hdkZgadVYZY[dgVhj[[^X^ZciaZc\i]
d[i^bZ!YVbV\Z!dkZg]ZVi^c\!dg[^gZbVngZhjai·
ZheZX^Vaan ^[ XdccZXiZY id Vc jcYZgh^oZY X^gXj^i#
IdgZYjXZ i]Z g^h` d[i]ZhZ]VoVgYh!Vkd^YdkZg"
adVY^c\ i]Z bVX]^cZ Yjg^c\ deZgVi^dc VcY bV`Z
hjgZ^i^hXdccZXiZYidVedlZghjeeanX^gXj^ii]Vi
bZZihi]ZgZfj^gZbZcih^ci]Z[daadl^c\hZXi^dc#
For your own safety and protection of
property, consult a qualified electrician if
you are unsure about wiring practices or
electrical codes in your area.
Note: The circuit requirements listed in this man-
ual apply to a dedicated circuitwhere only one
machine will be running at a time. If this machine
will be connected to a shared circuit where mul-
tiple machines will be running at the same time,
consult a qualified electrician to ensure that the
circuit is properly sized for safe operation.
6 edlZg hjeean X^gXj^i ^cXajYZh Vaa ZaZXig^XVa
Zfj^ebZciWZilZZci]ZWgZV`ZgWdmdg[jhZeVcZa
^ci]ZWj^aY^c\VcYi]ZbVX]^cZ#I]ZedlZghje"
eanX^gXj^ijhZY[dgi]^hbVX]^cZbjhiWZh^oZYid
hV[Zan]VcYaZi]Z[jaa"adVYXjggZciYgVlc[gdbi]Z
bVX]^cZ [dg Vc ZmiZcYZY eZg^dY d[ i^bZ# >[ i]^h
bVX]^cZ ^h XdccZXiZY id V X^gXj^i egdiZXiZY Wn
[jhZh!jhZVi^bZYZaVn[jhZbVg`ZY9#
Circuit Information
Circuit Requirements for 220V
I]^h bVX]^cZ ^h egZl^gZY id deZgViZ dc V ''%K
edlZghjeeanX^gXj^ii]Vi]VhVkZg^[^ZY\gdjcYVcY
bZZihi]Z[daadl^c\gZfj^gZbZcih/
Nominal Voltage .............................. 220V/240V
Cycle ..........................................................60 Hz
Phase ........................................... Single-Phase
Circuit Rating ...................................... 20 Amps
Plug/Receptacle ............................. NEMA 6-20


Extension Cords
LZ Yd cdi gZXdbbZcY jh^c\ Vc ZmiZch^dc XdgY
l^i] i]^h bVX]^cZ#>[ndjbjhijhZ Vc ZmiZch^dc
XdgY!dcanjhZ^i^[VWhdajiZancZXZhhVgnVcYdcan
dcViZbedgVgnWVh^h#
:miZch^dc XdgYh XVjhZ kdaiV\ZYgde!l]^X] bVn
YVbV\ZZaZXig^XVaXdbedcZcihVcYh]dgiZcbdidg
a^[Z#KdaiV\ZYgde^cXgZVhZhVhi]ZZmiZch^dcXdgY
h^oZ\Zihadc\ZgVcYi]Z\Vj\Zh^oZ\ZihhbVaaZg
]^\]Zg\Vj\ZcjbWZgh^cY^XViZhbVaaZgh^oZh#
6cnZmiZch^dcXdgYjhZYl^i]i]^hbVX]^cZbjhi
XdciV^c V \gdjcY l^gZ! bViX] i]Z gZfj^gZY eaj\
VcY gZXZeiVXaZ! VcY bZZi i]Z [daadl^c\ gZfj^gZ"
bZcih/
Minimum Gauge Size ...........................12 AWG
Maximum Length (Shorter is Better).......50 ft.
Grounding Instructions
I]^h bVX]^cZ BJHI WZ \gdjcYZY# >c i]Z ZkZci
d[XZgiV^cbVa[jcXi^dchdgWgZV`Ydlch!\gdjcY^c\
gZYjXZhi]Zg^h`d[ZaZXig^Xh]dX`Wnegdk^Y^c\V
eVi]d[aZVhigZh^hiVcXZ[dgZaZXig^XXjggZci#
>begdeZgXdccZXi^dcd[i]ZZfj^ebZci"\gdjcY^c\
l^gZ XVc gZhjai ^c V g^h` d[ ZaZXig^X h]dX`# I]Z
l^gZl^i]\gZZc^chjaVi^dcl^i]dgl^i]djinZaadl
hig^eZh^hi]ZZfj^ebZci"\gdjcY^c\l^gZ#>[gZeV^g
dggZeaVXZbZcid[i]ZedlZgXdgYdgeaj\^hcZX"
ZhhVgn!YdcdiXdccZXii]ZZfj^ebZci"\gdjcY^c\
l^gZidVa^kZXjggZciXVggn^c\iZgb^cVa#
8]ZX`l^i]VfjVa^[^ZYZaZXig^X^VcdghZgk^XZeZg"
hdccZa^[ndjYdcdijcYZghiVcYi]ZhZ\gdjcY^c\
gZfj^gZbZcih!dg^[ndjVgZ^cYdjWiVWdjil]Zi]Zg
i]Z idda ^h egdeZgan \gdjcYZY# >[ ndj ZkZg cdi^XZ
i]ViVXdgYdgeaj\^hYVbV\ZYdgldgc! Y^hXdc"
cZXi^i[gdbedlZg!VcY^bbZY^ViZangZeaVXZ^il^i]
VcZldcZ#
I]^hbVX]^cZ^hZfj^eeZYl^i]VedlZgXdgYi]Vi
]VhVcZfj^ebZci"\gdjcY^c\l^gZVcYV\gdjcY"
^c\ eaj\ h^b^aVg id i]Z [^\jgZ WZadl# I]Z eaj\
bjhidcanWZ^chZgiZY^cidVbViX]^c\gZXZeiVXaZ
djiaZii]Vi^hegdeZgan^chiVaaZYVcY\gdjcYZY^c
VXXdgYVcXZl^i]VaaadXVaXdYZhVcYdgY^cVcXZh#
No adapter should be used with the
provided plug. If the plug does not fit the
available receptacle, or the machine must
be reconnected for use on a different type
of circuit, the reconnection must be made
by a qualified electrician and comply with all
local codes and ordinances.
Serious injury could occur if you connect
the machine to power before completing the
setup process. DO NOT connect to power
until instructed later in this manual.
Figure 4. 
<gdjcY^c\Egdc\
8jggZci8Vggn^c\Egdc\h
6-20 PLUG
GROUNDED
6-20 RECEPTACLE


SECTION 3: SETUP
       
       

Description Qty
 
  
  
 
 
 
 
 
 
 
 
 
 
 
 
Items Needed for
Setup
Ndjg bVX]^cZ lVh XVgZ[jaan eVX`V\ZY [dg hV[Z
igVchedgiVi^dc# GZbdkZ i]Z eVX`V\^c\ bViZg^Vah
[gdb VgdjcY ndjg bVX]^cZ VcY ^cheZXi ^i# >[ ndj
Y^hXdkZgVcnYVbV\Z! please call us immediately
at (570) 546-9663for advice.
HVkZi]ZXdciV^cZghVcYVaaeVX`^c\bViZg^Vah[dg
edhh^WaZ ^cheZXi^dc Wn i]Z XVgg^Zg dg ^ih V\Zci#
Otherwise, filing a freight claim can be difficult.
L]ZcndjVgZXdbeaZiZanhVi^h[^ZYl^i]i]ZXdcY^"
i^dcd[ndjgh]^ebZci!^ckZcidgni]ZXdciZcih#
Unpacking
Lifting heavy machinery
or parts without proper
assistance or equipment
may result in strains, back
injuries, crushing injuries,
or property damage.
To reduce the risk of serious
injury, read and understand
this entire document before
using the machine!


Hardware Recognition Chart
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92

Grizzly Smoke Alarm G0690 User manual

Type
User manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI