Marshall Electronics Car Video System V-R902DP-AFHD User manual

Brand: Marshall Electronics

Model: Car Video System V-R902DP-AFHD

Type: User manual

This manual is also suitable for

V-R902DP-AFHD

Marshall Electronics

, Inc.

1910 East Maple Ave.

El Segundo, CA 90245

Tel: (800) 800-6608 / (310) 333-0606 • Fax: 310-333-0688

www.LCDRacks.com • sales@lcdracks.com

Marshall Electronics

V-R902DP-AFHD

High Definition Dual Screen LCD Monitor Set

Operating Instructions

2 19

Warranty

Marshall Electronics warranties to the first consumer that this V-R902DP-AFHD LCD monitor will, under normal use, be

free from defects in workmanship and materials, when received in its original container, for a period of one year from the

purchase date. This warranty is extended to the first consumer only, and proof of purchase is necessary to honor the

warranty. If there is no proof of purchase provided with a warranty claim, Marshall Electronics reserves the right not to

honor the warranty set forth above. Therefore, labor and parts may be charged to the consumer. This warranty does not

apply to the product exterior or cosmetics. Misuse, abnormal handling, alterations or modifications in design or

construction void this warranty. It is considered normal for a minimal amount of pixels, not to exceed three, to fail on the

periphery of the display active viewing area. Marshall Electronics reserves the option to refuse service for display pixel

failure if deemed unobtrusive to effective use of the monitor by our technicians. No sales personnel of the seller or any

other person is authorized to make any warranties other than those described above, or to extend the duration of any

warranties on behalf of Marshall Electronics, beyond the time period described above. Due to constant effort to improve

products and product features, specifications may change without notice.

09/07/07

Contents

Product Overview.....................................................................................................................................................4

Features ....................................................................................................................................................................4

Installation and Initial Setup ...................................................................................................................................5

Unpacking..............................................................................................................................................................5

Installation..............................................................................................................................................................5

Connections and Power-On...................................................................................................................................5

Front Panel Features ...............................................................................................................................................6

Power Button ........................................................................................................................................................6

Input Select Buttons...............................................................................................................................................6

On-Screen Menu Navigation Buttons....................................................................................................................6

User-Definable Function Buttons...........................................................................................................................6

Image Adjustment Knobs.......................................................................................................................................6

Tally Lights.............................................................................................................................................................6

Rear Panel Features.................................................................................................................................................7

Power Input............................................................................................................................................................7

Signal Input/Output................................................................................................................................................7

Tally Interface ........................................................................................................................................................7

Mounting Holes......................................................................................................................................................7

Compatible Input Formats.......................................................................................................................................8

On-Screen Menu.......................................................................................................................................................9

STRUCTURE OVERVIEW ....................................................................................................................................9

MAIN MENU AND NAVIGATION ..........................................................................................................................9

MARKER SETUP SUBMENU .............................................................................................................................10

16:9 Markers....................................................................................................................................................10

4:3 Markers......................................................................................................................................................11

Marker Background.........................................................................................................................................11

Center Marker..................................................................................................................................................11

VIDEO CONFIGURATION SUBMENU ...............................................................................................................12

Color Temperature Presets.............................................................................................................................12

Adjusting Color Bias........................................................................................................................................12

Adjusting Color Gain........................................................................................................................................12

Monochrome Mode..........................................................................................................................................13

Blue Only Mode...............................................................................................................................................13

Pixel-to-Pixel Mode..........................................................................................................................................13

Aspect Ratio Setting........................................................................................................................................14

Scanning Modes..............................................................................................................................................14

Delay Modes....................................................................................................................................................14

SYSTEM CONFIGURATION SUBMENU............................................................................................................15

Internal SMPTE Color Bars.............................................................................................................................15

User-Definable Function Buttons ....................................................................................................................15

Status Display..................................................................................................................................................15

Saving and Loading User Configuration Presets............................................................................................15

Specifications.........................................................................................................................................................16

Maintenance............................................................................................................................................................17

Warranty..................................................................................................................................................................18

Product Overview

The V-R902DP-AFHD is a dual screen high definition LCD monitor set featuring our completely digital TFT-MegaPixel

active matrix LCD platform. Utilizing dual 9-inch panels with 1.4 million pixels each, the V-R902DP-AFHD provides an

incredible amount of screen space while occupying only 4RU. Our proprietary digital signal processing features 10-bit A/D

conversion of all analog signals, with 4X over-sampling and 5-line super-adaptive 2D comb filtering of composite signals.

Emulation of SMPTE-C/EBU color and adjustable color temperature enable the most precise color representation

possible. De-interlacing is performed using our HyperProcess algorithm with motion adaptive interpolation. Multi-format

compatibility accommodates virtually all video formats including NTSC/PAL, 480i/p, 720p, and 1080i standards. VGA and

DVI inputs accept VESA standards allowing the display to be used as a computer monitor. Advanced features include

aspect ratio settings, a variety of screen markers, underscan mode, blue-only mode, monochrome mode, H/V delay, and

Pixel-to-Pixel mode.

Features

■

High-Resolution 9.0” Widescreen Panels

The V-R902DP-AFHD features an all-digital TFT-MegaPixel active matrix LCD system with 1.2 million pixels. The LCD

panel features a brightness of 400 cd/m

and a contrast ratio of 600:1 making the display ideal in a variety of

environments and lighting conditions.

■

Multi-Format Compatibility

With a variety of analog and digital inputs, the V-R902DP-AFHD accommodates virtually all video formats. Input types

include Composite Video, S-Video, YPbPr, SDI, VGA, and DVI with HDCP. Accepted formats include NTSC/PAL,

480i/p, 576i/p, 720p, 1035i, and 1080i standards, as well as VESA PC formats through XGA (1024 x 768).

■

End-to-End Digital Signal Processing

Analog signals are digitized using an advanced 10-bit process with 4x over-sampling, 5-line super-adaptive 2D comb

filtering, and exacting color space conversion. Video is scaled to fit on the screen in the highest possible resolution

using a state-of-the-art LSI that incorporates precision gamma correction and our HyperProcess motion adaptive

interpolation for interlaced images.

■

ColorMatch Conversion with Color Temperature Adjustment

Emulation of SMPTE-C/EBU color space allows the V-R902DP-AFHD to replace any broadcast CRT monitor. Settings

include D55, D65 and D95. Bias and Gain adjustment for each color enables precise color matching and white

balance.

■

Advanced Features

Aspect ratio settings, underscan mode, blue-only mode, monochrome mode, and H/V delay are a few of the advanced

features making the V-R902DP-AFHD at home in any broadcast environment. Pixel-to-Pixel mode also allows native

display of any incoming image format.

■

Flexible Screen Markers

A variety of screen markers in both 4:3 and 16:9 modes allow accurate monitoring of the different aspect ratios used in

broadcast environments.

■

User-Definable Function Buttons

Two user-assignable function buttons on the front-panel allow quick access to numerous settings and features

including aspect ratio, screen markers, monochrome mode, color temperature, delay mode, and more.

Specifications (continued)

Maintenance

■

Screen Cleaning

Periodically clean the screen surface using ammonia-free cleaning wipes (Marshall Part No. V-HWP-K). A clean micro-

fiber cloth can also be used using only non-abrasive and ammonia-free cleaning agents. Do not use paper towels.

Paper towel fibers are coarse and may scratch the surface of the polycarbonate faceplate or leave streaks on the

surface. Antistatic and fingerprint resistant cleaning agents are recommended. Do not apply excessive pressure to the

screen to avoid damaging the LCD.

■

Faceplate Dusting

Dust the unit with a soft, damp cloth or chamois. Dry or abrasive cloths may cause electrostatic charge on the surface,

attracting dust particles. Neutralize static electricity effects by using the recommended cleaning and polishing practice.

Specifications

■

PANEL

Screen Size 9.0” Diagonal

Display Area (h x v) 196.8 x 118.08 mm

Aspect Ratio 16:9 Native (4:3/16:9 Modes)

Pixels 800 x RGB x 480

Color Depth 24-bit (16,777,216 Colors)

Viewing Angle (h x v) 160° x 140°

Brightness 400 cd/m

Contrast Ratio 600:1

Dot Pitch (h x v) 0.082 x 0.246 mm

Pixel Pitch (h x v) 0.246 x 0.246 mm

■

VIDEO INPUT/OUTPUT

Video Input / Output

Supports SMPTE 170M, NTSC/PAL

S-Video (Y/C) Input / Output

Supports SMPTE 170M, NTSC/PAL

Input / Output

Supports SMPTE 260M, 274M, 296M

HD-SDI Input / Output

Supports ITU-R BT.656, SMPTE 259M, 292M

VGA Input

Supports RGBHV, RsGsBs, RGsB, RGB CS,

DVI Input

Supports Digital Signals Only (DVI-D)

HDMI, HDCP Supported

■

CONNECTORS

Video Input

Video 1 x BNC Female (75 Ω)

S-Video (Y/C) 1 x 4-Pin Mini-DIN

3 x BNC Female (75 Ω)

HD-SDI 1 x BNC Female (75 Ω)

VGA 1 x HD-15 Female

DVI 1 x DVI-I 29-Pin Female

Video Output (Active Loop-Through)

Video 1 x BNC Female (75 Ω)

S-Video (Y/C) 1 x 4-Pin Mini-DIN

3 x BNC Female (75 Ω)

SDI 1 x BNC Female (75 Ω)

Power Input

4-Pin XLR Male

Tally Interface

HD-15 Female

■

TALLY

3 LEDs (Green, Red, Yellow). Activation requires contact

closure of pin to ground on the HD-15 connector:

Pin No. Signal

1 M1 Green

2 M1 Red

3 M1 Yellow

4 Ground

5 Ground

6 N/C

7 N/C

8 N/C

9 N/C

10 N/C

11 M2 Green

12 M2 Red

13 M2 Yellow

14 Ground

15 Ground

■

ELECTRICAL

Power Consumption 2.5A @ 12VDC (30 W)

Voltage Requirement 12 VDC

V-PS12-5V-XLR Power Supply:

Input 100V-240V, 1.5A, 50-60Hz

Output 12VDC, 5A, 60W Max

V-Mount Battery Adapter

(Accepts standard 12V / 14.4V V-Mount Batteries)

■

MECHANICAL

Dimensions (w x h x d): 18.98” x 6.92” x 1.76”

Weight (Monitor Only): 6.40 lbs

Operating Temperature 32°F to 120°F (0°C to 50°C)

Storage Temperature -4°F to120°F (-20°C to 50°C)

Compliance ₠, FCC-Class A, ANSI-63.4

(Certificates on file)

RoHs Do not dispose. Return to

Manufacturer or Authorized

Recycle Facility.

Installation and Initial Setup

■

Unpacking

Carefully unpack the V-R902DP-AFHD monitor and verify that the following items are included:

• V-R902DP-AFHD Monitor

• V-PS12-5V-1 Power Supply with 2-Pin Twist Lock Connector

• Operating Instructions

Inspect the unit for any physical damage that may have occurred during shipping. Should there be any damage,

immediately contact Marshall Electronics at (800) 800-6608. If you are not located within the continental United States,

call +1 (310) 333-0606.

■

Installation

The V-R902DP-AFHD can be mounted in any standard EIA 19” equipment rack. The included rack mount adapter

brackets can be angled up to 110 degrees to provide the user full control over the viewing angle. Adequate ventilation

is required when installed to prevent possible damage to the monitor’s internal components.

■

Connections and Power-On

Plug the V-PS12-5V-1 power supply into an AC power source (100-240 V @ 50/60 Hz). Attach the 2-pin twist lock

connector to the back of the monitor. Please note that 12VDC can be also supplied directly to the monitor from a

variety of sources. The monitor will draw approximately 2.5 Amps at 12 Volts in operation.

Connect the required cables for video signal input and output. (Power must be applied to the V-R902DP-AFHD for the

active loop-though outputs to be activated.) All BNC connectors are rated at 75Ω.

Turn on the unit by pressing the power button located on the front panel. Select a video input by pressing the

corresponding input select button.

Rack Mount

Adapter Bracket

Front Panel Features

Power Button

Turn the monitor on by pressing the power button.

In the OFF state, the LED will shine red. The LED

will shine green when the monitor is turned on.

Input Select Buttons

Use the input select buttons to select the input to be

displayed:

• Video

• S-Video

• YPbPr (SD/HD)

• VGA

• DVI

• SDI (SD/HD)

Each input automatically detects the applicable

formats (See Compatible Input Formats – Page 8).

On-Screen Menu Navigation Buttons

Use the Menu, ↑, ↓, and Select buttons to display

and navigate the on-screen menu (See Main Menu

and Navigation – Page 9).

User-Definable Function Buttons

Two user-definable function buttons can be used for

direct access to various settings. Functions are

assigned using the on-screen menu (See User-

Definable Function Buttons – Page 15).

Image Adjustment Knobs

Use the image adjustment knobs to adjust the

following settings. Pressing each knob will display

the current status of the corresponding control:

• Brightness (0-64)

• Color (0-64)

• Tint (0-64) [NTSC Only]

• Contrast (0-64)

Tally Lights

Three tally LEDs (green, red, and yellow) are

provided as general purpose indicators. Each LED

can be individually controlled, providing multiple

indications. Tally LEDs are controlled via the HD-15

connector on the rear panel (See Tally Interface –

Page 7)

Top Front Panel

Lower Front Panel

On-Screen Menu (continued)

SYSTEM CONFIGURATION SUBMENU

■

Internal SMPTE Color Bars

Use to display internally generated SMPTE split-field color bars.

■

User-Definable Function Buttons

Use the FUNCTION 1 and FUNCTION 2 menu items to define each function button on the front panel of the monitor.

The following options are available for each button:

• DELAY Enable and rotate amongst delay modes.

• RATIO Toggle between 4:3 and 16:9 aspect ratios.

• BACK Rotate amongst marker backgrounds.

• CENTER Enable/disable center marker.

• MARKER Enable and rotate amongst marker settings (choices depend on aspect ratio setting).

• MONO Enable/disable monochrome mode.

• CTEMP Rotate amongst color temperature settings.

• PTP Enable/disable Pixel-to-Pixel mode.

FUNCTION 1 is set to RATIO by default.

FUNCTION 2 is set to PTP by default.

■

Status Display

Use to enable on-screen display of input/format status in the upper-left corner of the screen.

■

Saving and Loading User Configuration Presets

Use the SAVE CONFIG and LOAD CONFIG menus to save current settings to one of 6 presets, or load a preset. All

monitor settings on the monitor are saved, including the image adjustment knob settings.

• Use the LOAD CONFIG menu to load one of presets USR1 – USR6. Factory default settings can also be loaded

by selecting MFG. (Factory defaults cannot be overwritten.)

• Use the SAVE CONFIG menu to save the current settings to a preset from USR1- USR6.

Video Configuration Submenu

On-Screen Menu (continued)

VIDEO CONFIGURATION SUBMENU (continued)

■

Aspect Ratio Settings

Use to switch between 4:3 and 16:9 aspect ratios.

As the V-R902DP-AFHD monitor has a native resolution of 800 x 480 RGB pixels, incoming images are automatically

scaled to fit the screen:

• In 4:3 mode, images are scaled to fill the maximum 4:3 portion of the screen (640 x 480), with black bars filling the

remainder of the screen.

• In 16:9 mode, images are scaled to fill the entire 16:9 screen (800 x 480),

Note: The aspect ratio setting is ignored when Pixel-to-Pixel mode is enabled.

■

Scanning Modes

Use this setting to switch between normal and underscan modes:

• In normal scan mode, the active portion of the video signal is displayed on the screen, with 0% overscan.

• In underscan mode, area around the active video area is displayed on the screen, resulting in blanking intervals

being shown around the perimeter of the active image. Use this mode to clearly view the edges of the active video

area.

■

Delay Modes

Use this setting to enable one of three delay modes (H/V, H, V):

• In H/V delay mode, both horizontal sync and vertical sync are delayed, resulting in both horizontal and vertical

blanking periods being shown on the screen.

• In V delay mode, vertical sync is delayed so that the vertical blanking period is displayed on screen.

• In H delay mode, horizontal sync is delayed so that the horizontal blanking period is displayed on the screen.

Note: Delay modes are only available in normal scan mode.

4:3 Mode

16:9 Mode

Rear Panel Features

Power Input

Connect the 12VDC input to the 2-Pin twist lock power

input connector. Power can be supplied from the

included power supply, or from a variety of DC sources

supplying at least 2.5 Amps at 12 Volts.

IMPORTANT: If using a power source other than the

included power supply, be sure that the polarity of the

DC input is correct.

Signal Input/Output

Connections:

• Composite Video Input/Output (BNC)

• S-Video Input/Output (4-Pin Mini-DIN)

• YP

Input/Output (BNC x 3)

• SDI Input/Output (BNC)

• VGA (HD-15)

• DVI (29-Pin connector, DVI-D signals only)

All outputs are active and require the monitor to be

powered.

Tally Interface

Each tally light is activated via the HD-15 connector by

connecting the corresponding pin to ground. A variety of

external devices can be used to perform the contact

closure. No additional power should be supplied to the

HD-15 port.

Tally Interface: HD-15 Pinout

Pin No. Signal

1 M1 Green

2 M1 Red 1

3 M1 Yellow

4 Ground

5 Ground

6 N/C

7 N/C

8 N/C

9 N/C

10 N/C

11 M2 Green

12 M2 Red

13 M2 Yellow

14 Ground

15 Ground

Compatible Input Formats

Format Composite S-Video YPbPr SDI VGA DVI-D

NTSC

● ●

PAL

● ●

525i

● ● ●

625i

● ● ●

486p / 59.94

● ●

576p / 50

● ●

1035i / 60

● ●

1035i / 59.94

●

1080i / 60

● ● ●

1080i / 59.95

● ● ● ●

1080i / 50

● ● ● ●

1080psF / 24

● ● ● ●

1080psF / 23.98

● ● ● ●

1080p / 30

1080p / 29.97

1080p / 25

720p / 60

● ● ● ●

720p / 59.94

● ● ● ●

720p / 50

● ● ● ●

720p / 30

720p / 29.97

720p / 25

640 x 480 @ 60Hz

● ●

640 x 480 @ 75Hz

● ●

640 x 480 @ 85Hz

● ●

800 x 600 @ 60Hz

● ●

800 x 600 @ 75Hz

● ●

800 x 600 @ 85Hz

● ●

1024 x 768 @ 60Hz

● ●

1024 x 768 @ 75Hz

● ●

1024 x 768 @ 85Hz

● ●

1280 x 1024 @ 60Hz

On-Screen Menu (continued)

VIDEO CONFIGURATION SUBMENU (continued)

■

Monochrome Mode

Use this setting to enable monochrome mode. Only the luminance of the image will be displayed as a grayscale

picture.

■

Blue-Only Mode

Use this setting to enable Blue-Only mode. This mode displays only the blue color component of the image, switching

off the red and green components. Use this mode when calibrating the monitor to SMPTE color bars with the following

procedure:

1. Allow the monitor to warm up for at least 5-10 minutes.

2. Display SMPTE split-field color bars on the monitor using the internal generator or an external source.

3. Enable Monochrome mode.

4. Locate the pluge pattern (super black, black, and gray bars) at the lower-right corner of the screen. Adjust the Brightness knob until there is

no visible difference between the super black and black bars, but the gray bar is still visible.

5. Adjust the Contrast knob until an even grayscale appears along the top bars.

6. Disable Monochrome mode.

7. Enable Blue-Only mode and adjust the Color knob so that the outermost bars (white and blue) appear to match in brightness.

8. Composite/S-Video NTSC only: Adjust the Tint knob until the third bar from the left (cyan) and the third bar from the right (magenta) appear to

match in brightness.

9. Disable Blue-Only mode.

■

Pixel-to-Pixel Mode

Use this setting to enable Pixel-to-Pixel mode.

This mode bypasses the monitor’s internal scaling function and displays incoming images in their native resolution and

aspect ratio, with a one-to-one mapping:

• For incoming formats smaller than the native resolution of the LCD panel (800 x 480), the image will be displayed

in the center of the screen using only the necessary LCD pixels. For example, NTSC images will occupy exactly

720 x 480 pixels. The surrounding pixels will be black.

• For incoming formats exceeding 800 x 480 pixels, only the center 800 x 480 of the incoming image will displayed

occupying the whole screen, with the remainder of the picture cropped. For example, 1080i formats will both be

cropped to 800 x 480 and displayed full-screen.

Note: Pixel-to-Pixel mode will utilize the entire screen (800 x 480) regardless of the aspect ratio setting. Pixel-to-Pixel

mode is not available when using the VGA or DVI inputs.

On-Screen Menu (continued)

VIDEO CONFIGURATION SUBMENU

■

Color Temperature Presets

Use this setting to choose one of three color temperature presets:

• D55 (5500K)

• D65 (6500K)

• D93 (9300K)

• USER (Adjustable Color Bias and Gain)

■

Adjusting Color Bias

Use this submenu to adjust bias of the color response. Adjust the bias for each color to alter the white balance of the

image. The Color Temperature preset will automatically switch to USER when Color Bias settings are adjusted. It is

normal for color bias adjustments to be very subtle.

■

Adjusting Color Gain

Use this submenu to adjust gain of the color response. The Color Temperature preset will automatically switch to

USER when Color Gain settings are adjusted.

Video Configuration Submenu

Color Bias Menu

Color Gain Menu

On-Screen Menu

STRUCTURE OVERVIEW

MAIN MENU AND NAVIGATION

Access the main menu by pushing and holding the MENU button on the front panel of the monitor.

• Step through menu items using the ↑ and ↓ buttons.

• Choose a menu item by pressing SELECT.

• Rotate through options using the ↑ and ↓ buttons.

• Choose a setting by pressing SELECT.

• Return to the previous menu by pressing MENU.

• Exit the main menu by pressing MENU. The menu will automatically

time out after 8 seconds. After exiting the menu, wait 1-2 seconds

before displaying the menu again.

MARKER 16:9

OFF, 13:9, 14:9, 4:3, 2.35:1,

1.85:1, 95%, 93%, 90%,

88%, 80%

MARKER 4:3

OFF, 95%, 93%, 90%, 88%,

80%

MARKER BACKGROUND

OFF, HALF, BLACK

MARKER SETUP

CENTER MARKER

OFF, ON

COLOR TEMP

D55, D65, D93, USR

RED (0-100)

GREEN (0-100)

ADJ COLOR BIAS

BLUE (0-100)

RED (0-100)

GREEN (0-100)

ADJ COLOR GAIN

BLUE (0-100)

MONO

OFF, ON

BLUE ONLY

OFF, ON

PIXEL TO PIXEL

OFF, ON

ASPECT RATIO

4:3, 16:9

SCAN

NORMAL, UNDER

VIDEO CONFIG

DELAY

OFF, H/V, V, H

SMPTE BAR

OFF, ON

FUNCTION 1

DELAY, RATIO, BACK,

CENTER, MARKER, MONO,

CTEMP, PTP

FUNCTION 2

DELAY, RATIO, BACK,

CENTER, MARKER, MONO,

CTEMP, PTP

STATUS DISPLAY

OFF, ON

LOAD CONFIG

USR1, USR2, USR3, USR4,

USR5, USR6, MFG

MAIN

SYSTEM CONFIG

SAVE CONFIG

USR1, USR2, USR3, USR4,

USR5, USR6

Main Menu

On-Screen Menu (continued)

MARKER SETUP SUBMENU

■

16:9 Markers

Use this setting to superimpose one of 10 markers on the screen when in 16:9 mode. This setting is disabled when the

aspect ratio is set to 4:3, or when Pixel-to-Pixel, Underscan, or H/V Delay is enabled.

• OFF (No Marker)

• 13:9 Aspect Ratio

• 14:9 Aspect Ratio

• 4:3 Aspect Ratio

• 2.35:1 Aspect Ratio

• 1.85:1 Aspect Ratio

• 95% Safe Area

• 93% Safe Area

• 90% Safe Area

• 88% Safe Area

• 80% Safe Area

16:9 Marker Examples:

Marker Setup Submenu

OFF (No Marker)

4:3 Aspect Ratio Marker2.35:1 Aspect Ratio

90% Safe Area

On-Screen Menu (continued)

MARKER SETUP SUBMENU (continued)

■

4:3 Markers

Use this setting to superimpose one of 5 markers on the screen when in 4:3 mode. This setting is disabled when the

aspect ratio is set to 16:9, or when Pixel-to-Pixel, Underscan, or H/V Delay is enabled.

• OFF (No Marker)

• 95% Safe Area

• 93% Safe Area

• 90% Safe Area

• 88% Safe Area

• 80% Safe Area

4:3 Marker Examples:

■

Marker Background

Use this setting to choose how selected markers are displayed on the screen:

• OFF The marker is superimposed on the complete image.

• Half-tone Image area beyond the marker is shown at 50% intensity.

• Black Image area beyond the marker is shown at 0% intensity (black).

Example (80% Marker in 4:3 Mode):

■

Center Marker

Use this setting to display a center marker on the screen. This feature is not available when H/V delay is on.

Center Marker

Background OFF Half-tone Background Black Background

OFF (No Marker) 90% Safe Area

Marshall Electronics Car Video System V-R902DP-AFHD User manual

Brand: Marshall Electronics

Model: Car Video System V-R902DP-AFHD

Type: User manual

This manual is also suitable for

V-R902DP-AFHD

Download PDF

report

Marshall Electronics Car Video System V-R902DP-AFHD User manual

This manual is also suitable for

Marshall Electronics Car Video System V-R902DP-AFHD User manual

Related papers

Other documents