CURT 11749 Installation guide

Type
Installation guide

CURT 11749 is a vehicle trailer hitch designed for the 1998-2005 Mazda Miata convertible. It offers a gross load capacity of 2,000 lbs. for weight carrying and a tongue weight of 200 lbs. This hitch mounts to the inside surface of the left and right frame rail extensions and requires drilling for installation. It comes with all necessary hardware, including handle nuts, washers, and fasteners. The hitch is constructed from durable materials and is backed by Curt Manufacturing's warranty.

CURT 11749 is a vehicle trailer hitch designed for the 1998-2005 Mazda Miata convertible. It offers a gross load capacity of 2,000 lbs. for weight carrying and a tongue weight of 200 lbs. This hitch mounts to the inside surface of the left and right frame rail extensions and requires drilling for installation. It comes with all necessary hardware, including handle nuts, washers, and fasteners. The hitch is constructed from durable materials and is backed by Curt Manufacturing's warranty.

Parts List
DESCRIPTIONPART NUMBERQTYITEM
HHCS,7/16-14 UNC,1-1/4,GRD8,YZ10-1042541
NUT, HANDLE, SER-FLANGE,7/16-14 UNC, GRD8, YZ20-0017242
WASHER,LOCK,7/16,YZ30-0018443
GROSS LOAD CAPACITY WHEN USED AS A WEIGHT CARRYING HITCH: LBS. TRAILER WEIGHT & LBS. TONGUE WEIGHT.
***DO NOT EXCEED VEHICLE MANUFACTURER'S RECOMMENDED TOWING CAPACITY.***
HITCH WEIGHT: LBS.
INSTALL TIME: MINUTES
INSTALL NOTES:
INSTALLATION STEPS
PERIODICALLY CHECK THIS RECEIVER HITCH TO ENSURE THAT ALL FASTENERS
ARE TIGHT AND THAT ALL STRUCTURAL COMPONENTS ARE SOUND.
Curt Manufacturing Inc., warrants this product to be free of defects in material and/or workmanship at the time of retail purchase by the original purchaser. If the product is found to be defective,
Curt Manufacturing Inc., may repair or replace the product, at their option, when the product is returned, prepaid, with proof of purchase. Alteration to, misuse of, or improper installation of
this product voids the warranty. Curt Manufacturing Inc.'s liability is limited to repair or replacement of products found to be defective, and specifically excludes liability for incidental or
consequential loss or damage.
2,000 200
17
30
98-05 MAZDA MIATA CONVERTIBLE
11/24/2020
11749 / 247314
1) This hitch mounts to the inside surface of the left and right frame rail extensions.
2) Position the hitch up between the frame rail extensions, with the hitch plates as far rearward as possible and
flush at the bottom surface of the frame rail extensions. Using the hitch as a template, mark the centers of
the holes to be drilled for fasteners as shown.
3) Remove the hitch and drill for fasteners.
4) Position the hitch on the vehicle matching the holes in the frame rail extensions with the holes in the hitch
plates. Install fasteners as shown. Pass handle nuts up through the opening at the bottom of the frame rails
extensions.
5) Torque all 7/16 fasteners to 70 lb-ft.
DRILLING REQUIRED
3
1
DRIVER SIDE
FRAME RAIL EXTENSION
PASSENGER SIDE
FRAME RAIL EXTENSION
2
DESIGNED FOR USE WITH
BALLMOUNT #55001 / 45501
  • Page 1 1

CURT 11749 Installation guide

Type
Installation guide

CURT 11749 is a vehicle trailer hitch designed for the 1998-2005 Mazda Miata convertible. It offers a gross load capacity of 2,000 lbs. for weight carrying and a tongue weight of 200 lbs. This hitch mounts to the inside surface of the left and right frame rail extensions and requires drilling for installation. It comes with all necessary hardware, including handle nuts, washers, and fasteners. The hitch is constructed from durable materials and is backed by Curt Manufacturing's warranty.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI