Whirlpool ADG 799 Program Chart
- Category
- Dishwashers
- Type
- Program Chart
Whirlpool ADG 799 is a dishwasher that offers a variety of features to make dishwashing easier and more efficient. It has 9 programs to choose from, including a soak cycle for lightly soiled dishes, a delicate cycle for glassware, and a sanitize cycle for heavily soiled dishes. The dishwasher also features a delayed start option, which allows you to set the dishwasher to start washing at a later time, and an extra rinse option, which ensures that all detergent is removed from the dishes.
Whirlpool ADG 799 is a dishwasher that offers a variety of features to make dishwashing easier and more efficient. It has 9 programs to choose from, including a soak cycle for lightly soiled dishes, a delicate cycle for glassware, and a sanitize cycle for heavily soiled dishes. The dishwasher also features a delayed start option, which allows you to set the dishwasher to start washing at a later time, and an extra rinse option, which ensures that all detergent is removed from the dishes.
5019 396 96044
GB
ADG 799
Quick Reference Guide
Before using the dishwasher, you are advised to read the user instructions!
(We reserve the right to make technical modifications)
Whirlpool is a registered trademark of Whirlpool USA
Add regeneration salt
Only add regeneration salt immediately before starting a
wash programme.
Add rinse aid
Extra programmes button
To select one of the three extra programmes,
press the button after selecting the main
programme (3, 4, 5); see programme table.
The function remains stored.
“Delayed start” button
The wash cycle can be programmed to start after 1-9
hours. The delayed start can be programmed either
before or after selecting the desired wash programme.
When the door is closed, a pre-wash cycle is run, after
which the delayed start countdown begins.
Water stop device activated
Switch off the dishwasher andcontact the After-Sales Service.
The dishwasher overfills with water
Reset and start the programmeagain from the beginning. If
the problem persists, contact the After-Sales Service.
The water heating system is not working
Reset and start the programmeagain from the beginning. If
the problem persists, contact the After-Sales Service.
Water heating anomaly
Reset and start the programme again from the beginning. If
the problem persists, contactthe After-Sales Service.
The dishwasher does not fill with water
Check the water supply and filters, and make sure that
there are no kinks in the water inlet hose. Open and
close the door in order to continue.
The dishwasher does not drain
Make sure that the filterunit and drain hose are not
clogged and if necessary clean them.
Flow meter
(if provided)
anomaly
Reset and start the programmeagain from the beginning. If
the problem persists, contact the After-Sales Service.
Alternate washing system
(if provided)
anomaly
Reset and start the programmeagain from the beginning. If
the problem persists, contact the After-Sales Service.
Fault in water load system
Switch off the dishwasher and contact the After-Sales Service.
(*) Extra functions available in all programmes, except prewash.
(**) This programme features an antibacterial rinse at the end to
guarantee a further reduction of bacteria. If a constant
temperature is not maintained during the antibacterial rinse
cycle (e.g. due to door opening or power failure), the
programme lights flash indicating that the antibacterial action
cannot be guaranteed.
1) Reference programme for energylabel in compliance with EN
50242 regulations.
2) Refer to “User instructions”.
3) Programme values obtained according to EN 50242. Values
may vary in relation to usage, e.g.: different loads, water
temperatures - above or below 15° C - as well as water
hardness and power supply voltage, etc.
On/Off button
Press the ON button to switch on the dishwasher. The
indicator lamp of the last programme selected lights up; at
the end of the cycle anacoustic signal sounds.
Programme selection button
Press the button to select a programme.
The corresponding indicator lamp comes when a
programme is selected.
Indicators
Extra functions (*)
Fault indicators
Indicators
Off
Blinking
On
Programme Table
Detergent
2)
Consumption
3)
Programmes Loading instructions A B Litres kWh Minutes
Soak cold
Dishes to be washed later. — — 5.0 0.02 9
Delicate 45°C
Lightly soiled dishes with no dried-on food. X — 12.0 0.90 60
Eco
1)
55°C
Normally soiled dishes. X — 13.0 1.01 175
Normal 65°C
Normally to heavily soiled dishes. X — 17.0 1.20 80
Sanirinse
(**)
70°C
Normally or heavily soiled dishes with
antibacterial wash.
X X 20.0 1.60 115
+
Short 38°C
Lightly soiled dishes with no dried-on food,
washed immediately after use.
X — 13.0 0.85 45
+
Half load 65°C
Smaller load of normally soiled dishes, washed
immediately after use.
X — 12.0 1.20 85
+
Strong 70°C
Recommended for heavily soiled dishes. X X 17.0 1.45 85
39696044GB.fm Page 1 Thursday, July 8, 2010 4:36 PM
Black process 45.0° 150.0 LPI
12-0,93
How to use the appliance
Further indications are given in the single chapters and in the user instructions.
Press the
On/Off
button .
Large compartment
A
Small compartment
B
Mechanical indicator lamp
C
.
Electric indicator on control panel (if provided).
On models with water softener system only.
Mechanical indicator lamp
D
.
Electric indicator on control panel
(if provided).
Refer to the dishwasher loading instructions.
Press the button until the desired programme lights up.
If necessary (where present).
The corresponding indicator lamp lights up.
“Cancel”
Open the door, press
until the indicator lamps 4 +
5 light up.
Close the door, after about 1
min. the cycle ends.
“Change programme in progress”
Open the door.
Select another programme and close the
door in order to start the new cycle.
- Only open the dishwasher if necessary
(Warning: beware of hot steam!
- If the appliance is switched off during a
wash cycle, when switched on again it
will resume the cycle from where it was
interrupted.
At the end of the programme an acoustic signal will sound. Open the door
and press the
On/Off
button . All the indicator lamps switch off.
Attention: Care must be taken when opening the door, as steam
will escape!
Empty the dishwasher starting from the bottom rack.
Open the door,
switch on the appliance
How to fill the detergent
dispenser
A
B
C
Check the rinse aid level
Check the
regeneration salt level
D
Load the racks
Select a programme
Select additional options
Close the door
to start the programme
Turn on the water tap,
close the door
Wash cycle
Switching off the appliance
Turn off the water tap,
unload the racks
39696044GB.fm Page 2 Thursday, July 8, 2010 4:36 PM
Black process 45.0° 150.0 LPI
Dishwasher loading instructions and racks provided
Upper basket:
for the model in use
Crockery holder (A):
Depending on the position: up or
down.
Long-handled utensils, cups and
glasses. Place the glasses to the side
of the rack or holders.
Place long and narrow utensils in
the centre of the rack or holders.
Long-handled utensils (e.g.
carving forks, knives) must be
arranged with the sharp end
facing in towards the appliance.
Rack height adjustment:
Release the caps (
B
) of both rack
rails.
Take the rack out.
Reposition the rack at the desired
height.
Close the caps (
B
).
The rack must be level on both
sides.
Lower basket:
Depending on the model with fixed
or tilting plate holders.
Cutlery basket:
Some models are provided with a grid
(
C
) that can be fitted onto the cutlery
basket to keep items separated.
Sharp knives and forks that
might cause injury must be
placed in the cutlery basket
with the sharp end facing
downwards.
Only use dishwasher-proof crockery and dishes. Do not try to wash items that are not suitable for washing in a
dishwasher, such as: wooden items, aluminium, plastic utensils, tin, hand-decorated crockery (unglazed), silver cutlery.
A
A
A
A
B
B
C
C
C
C
39696044GB.fm Page 3 Thursday, July 8, 2010 4:36 PM
Black process 45.0° 150.0 LPI
What to do if...
If a fault occurs, before contacting our After-Sales Service, make the following checks to try and remedy the problem
(* see also the corresponding chapter in the user instructions).
Problem Cause Remedy
The appliance is not
working
• No water supply. • Open the water tap.
• The appliance doesn't fill enough water. • Clean the water supply tap filter.
• Ensure there are no kinks in the water hose.
• There is a power failure. • Insert the plug into the mains socket.
•Open the door.
•Close the door.
• Check the domestic circuit fuse.
If dishes are not
perfectly dry
•Not enough rinse aid. •Increase dosage *.
• Residual water in cavities. • Load dishes at an angle.
If dishes are not
perfectly clean
• The water jet does not reach the
dishes.
• Arrange dishes so that items do not touch each other.
Load dishes upside down.
• Too little detergent; • Follow recommended detergent dosage.
• Unsuitable programme. • Select a more intense wash cycle.
• Spray arms blocked. • The spray arms must be able to turn freely.
• Spray arm nozzles jammed. • Remove any impurities obstructing the water flow*.
• Incorrect detergent/detergent too old. • Use a good quality detergent.
Sandy or grainy residues
• Clogged filters. • Check filters regularly/if necessary clean them*.
• Filters incorrectly assembled. • Insert the filter correctly*.
Colour of plastic parts
faded
• Tomato/Carrot juice.... • Depending on the material, if necessary use a
detergent with a greater whitening power.
Deposits on dishes
• can be removed • Streaks on the dishes/glasses. • Decrease the rinse aid setting*.
• Layer of salt on dishes/glasses. • Close the salt container lid properly*.
• not removable • Insufficient water softening, calcium
deposits.
• Change water hardness setting, if necessary add salt*.
Opaque glasses/glasses
not sparkling
• Cannot be washed in the dishwasher. • Use suitable glasses.
Rust on cutlery
• Not made of stainless steel. •Use suitable cutlery.
If, after carrying out the above checks the malfunction persists or appears again, turn the appliance off and turn off the water
supply tap, then call our After-Sales Service (see guarantee).
Before contacting our After-Sales Service, please have the following information ready:
• The nature of the fault.
• The appliance type and model.
• The service code (the number indicated on the adhesive rating plate)
inside the door on the right-hand side.
39696044GB.fm Page 4 Thursday, July 8, 2010 4:36 PM
Black process 45.0° 150.0 LPI
-
1
-
2
-
3
-
4
Whirlpool ADG 799 Program Chart
- Category
- Dishwashers
- Type
- Program Chart
Whirlpool ADG 799 is a dishwasher that offers a variety of features to make dishwashing easier and more efficient. It has 9 programs to choose from, including a soak cycle for lightly soiled dishes, a delicate cycle for glassware, and a sanitize cycle for heavily soiled dishes. The dishwasher also features a delayed start option, which allows you to set the dishwasher to start washing at a later time, and an extra rinse option, which ensures that all detergent is removed from the dishes.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Whirlpool ADG 4500 User guide
-
-
-
Whirlpool ADG 3500 Program Chart
-
-
-
-
-
-
Whirlpool GCIK 6541/1 IN User guide
Other documents
-
IKEA DWF 417 W Program Chart
-
IKEA DWF 407 W Program Chart
-
-
Bauknecht GCXK 5521 Program Chart
-
Bauknecht GMX 5555 Program Chart
-
-
-
-
KitchenAid KDFX 6020 Program Chart
-