Facom 711P.500 Owner's manual

Brand: Facom

Model: 711P.500

Type: Owner's manual

Facom 711P.500 is a versatile ammeter clip for measuring direct and alternating current. With a capacity of 600A DC and 400A AC, it's suitable for a wide range of applications, from measuring current consumption of electrical appliances to checking the output of an alternator. Its compact size and lightweight design make it easy to use in confined spaces. The 711P.500 features a large, easy-to-read display that shows the current reading in real time. It also has a built-in zero function for accurate measurements. To use the 711P.500, simply clamp the jaws around the wire you want to measure. The display will show the current reading in milliamps (mA).

Page is loading ...

Safety

Never carry out measurements on non-insulated wires with a

potential of over 600 V in relation to earth.

Never open the case on the ammeter clip before having first disconnected it from

any source of electricity.

Do not use the 711P.500 clip outside.

Technical specifications

Size : 250 x 97 x 44 mm

Weight : 440 g

1 battery : 9 volts

(type: 6LR61 - 6LF22 - NEDA 1604)

Endurance :120 hours with alkaline battery

: 60 hours with saline battery

Indication that battery is running out

: green indicator light flashes

Capacity : 600 A DC or 400 A AC

(600 A en crête)

Output signal : 1 mV, DC or AC for 1 A, DC or AC

Measuring equipment impedance :

≥≥

≥ 1 M

ΩΩ

Ω and

≤≤

≤ 100 pF

Operating temperature range : -10° to +65°C

Storage temperature range : -40° to +80°C

Relative humidity in use : < 20 to 75% RH

Relative humidity in storage : < 80% RH

(up to 40°C)

Double insulation : Installation category III

Degree of pollution : 2

(per standard IEC 1010-1)

Seal : IP40

(per IEC 529)

Electrical safety :

(per standard IEC 1010-2-032)

Degree of casing protection :

(per standard IEC 529)

Radiated field : 3 V/m

(per IEC 801-3)

Free fall : 1 m

(per IEC 1010)

Vibrations : 0.75 mm

(per IEC 68.2.6)

Impacts : 0.5 joules

(per IEC 68.2.27)

Electric shocks : 3 kV

(per IEC 801.5)

Electrostatic discharge : 4 kV class 2

(per IEC 1000-4-2)

Rapid transients : 1 kV level 2, aptitude criteria B

(IEC 1000-4-4)

Maximum dimensions : 30mm-Ø cable or 2 of 24mm-Ø cables

: Bar cross-section 50 x 10 mm

Comes with a 1.5 m cord with two 4 mm-diameter male plugs on the end, a 9 V

battery not fitted, an instruction manual and a guarantee leaflet.

Gap for wire

Jaw

Anti-slip protector

Opening lever On/off switch

Direction of direct current

Sealed 1.5 m cord

Button to reset when

under direct current

Green «on» indicator

light

Connection

• Insert the red safety plug into the «

» terminal on the 711 multimeter.

• Insert the black safety plug into the «COM» terminal on the multimeter.

• Turn the selector on the multimeter to «V», the voltmeter position.

• Slide the button on the 711P.500 clip to «1 m V/A» ; if the green indicator

light marked ON is constant the battery is fine, if it flashes the battery is too low.

Setting

• Alternating current

: direct readover

(1 mV = 1 A)

• Direct current: press the /

button on the 711 until the « » symbol is

displayed.

• Use the «sunken» grey button on the 711P.500 clip to set to 000.0 mV on

the multimeter display.

Use

Place the ammeter clip jaws around the wire to be checked, the arrow on the

jaws showing the standard current direction.

Alternating current «

»: when the current passes through the wire, read the

direct value on the 711 multimeter display. To check an alternating current, the

» sign has to be displayed on the screen with the « /

» button.

Direct current « »: when the current passes through the wire, follow the

standard current direction. To check a direct current, the « » sign has to be

displayed on the screen with the « /

» button.

Read the actual current on the multimeter screen passing through the wire being

tested

(1mV=1A)

. When the «-» sign appears in front of the value displayed, the

direction of the current passing through the test wire does not match the indicator

arrow on the clip, so reverse it. With the 711 multimeter, you can store the

minimum or maximum current value on the display with the MIN/MAX button.

---

Measuring alternating current

For example : Current consumption of electrical appliances (industrial motors,

radiators, dishwashers etc.)

Measuring direct current

For example : Alternator output, current consumption of a starter, pre-heating

plugs, accessories etc.

Changing the battery

Slide the button on the ammeter clip to OFF. On the back of the unit, slacken

the captive screw, take the lid off and replace the 9 volt battery

(6LR61 or 6LF22 or

NEDA 1604)

. Put the lid back on before using your clip again.

12 volt

Page is loading ...

UNITED KINGDOM

EIRE

FACOM Tools Ltd

Bridge Wharf - Bridge Road

CHERTSEY - SURREY KT16 8LJ

UNITED KINGDOM

✆ : (01932) 566099

Fax : (01932) 562653

DEUTSCHLAND

FACOM GmbH

Postfach 13 22 06

42049 Wuppertal

Otto-Wels-Straße 9

42111 Wuppertal

DEUTSCHLAND

✆ : (0202) 704051

Fax : (0202) 706958

NEDERLAND

FACOM Gereedschappen BV

Kamerlingh Onnesweg 2

Postbus 134

4130 EC Vianen

NEDERLAND

✆ : (0347) 372334

Fax : (0347) 376020

ESPAÑA

PORTUGAL

FACOM Herramientas, S.L

Poligono industrial de Vallecas

C/.Luis 1°, s/n-Nave 95 -

2°Planta

28031 Madrid

ESPAÑA

✆ : (91) 778 21 13

Fax : (91) 778 27 53

ITALIA

U.A. FACOM Italia

Via Ronchetti 3

21041 Albizzate (VA)

ITALIA

✆ : (0331) 985811

Fax : (0331) 985930

BELGIQUE/BELGIE

S.A. FACOM N.V

Weihoek 4 1930 Zaventem

BELGIQUE

✆ : (02) 720 92 07

Fax : (02) 721 24 11

SUISSE/SCHWEIZ

AUSTRIA

FACOM S.A./AG

12 route Henri-Stéphan

1762 Givisiez/Fribourg

SUISSE

✆ : (4126) 466 42 42

Fax : (4126) 466 38 54

UNITED STATES

FACOM TOOLS Inc.

3535 West 47th Street

Chicago Illinois 60632

U.S.A.

✆ : (773) 523 1307

Fax : (773) 523 2103

SINGAPORE

FAR EAST

FACOM Tools FAR EAST Pte Ltd

15 Scotts Road

Thong Teck Building # 08-01-02

Singapore 228218

SINGAPORE

✆ : (65) 732 0552

Fax : (65) 732 5609

FRANCE

Société FACOM

6-8 rue Gustave Eiffel BP.99

91423 Morangis cedex

FRANCE

✆ : 01 64 54 45 45

Fax : 01 69 09 60 93

Facom 711P.500 Owner's manual

Brand: Facom

Model: 711P.500

Type: Owner's manual

Download PDF

report

in other languages

italiano: Facom 711P.500 Manuale del proprietario
français: Facom 711P.500 Le manuel du propriétaire
español: Facom 711P.500 El manual del propietario
Deutsch: Facom 711P.500 Bedienungsanleitung
Nederlands: Facom 711P.500 de handleiding

Facom 711P.500 Owner's manual

Facom 711P.500 Owner's manual

in other languages

Related papers

Other documents