Schwaiger UFB125 User manual

Bedienungsanleitung:

Universal Touch Panel Fernbedienung mit Lernfunktion

Instruction manual:

Universal touch panel remote control with learning

Mode d‘emploi:

Télécommande universelle avec fonction d‘apprentissage

Istruzioni per l‘uso:

Telecomando universale con funzione di apprendimento

UFB125

Page is loading ...

8

Important safeguards

Signal Word Deﬁ nitions

NOTE: These are general deﬁ nitions only; all may not pertain to

the actual product purchased.

DANGER – Indicates an imminently hazardous situation, which,

if not avoided, will result in death or serious injury. Usage of

this signal word is limited to the most extreme situations.

WARNING – Indicates a potentially hazardous situation, which,

if not avoided, could result in death or serious injury.

CAUTION – Indicates a potentially hazardous situation, which,

if not avoided, may result in minor/moderate injury or product/

property damage. It also alerts against unsafe practices.

READ ALL INSTRUCTIONS BEFORE USE

WARNING

Choking Hazard – Small parts.

Not for children under 3 years.

9

CAUTION

To reduce the risk of personal injury or product/property damage:

• This product is intended for indoor, non-industrial, non-commercial,

household use in controlling functions of select electronic devices. Do

not use the product outdoors or for any other purpose.

• Do not immerse the product in water or other liquids.

SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE

Battery handling and usage

WARNING: Keep batteries away from children and pets.

• Follow the battery manufacturer’s safety and usage instructions.

• Do not mix a used battery with a new battery, or mix different chemistries

or sizes of batteries.

• Insert the batteries observing the proper polarity (+/−) as indicated

inside the battery compartment. CAUTION: Failure to properly

align the battery polarity can cause personal injury and/or property

damage.

• Remove a spent or discharged battery from the product. Remove the

batteries when not using the product for an extended period.

• Never throw batteries into a ﬁ re. Do not expose batteries to ﬁ re or

other heat sources.

• Dispose or recycle spent/discharged batteries in compliance with all

applicable laws. For detailed information, contact your local solid

waste authority.

10

Battery installation

This product uses two “AAA” size batteries (not included).

1. Remove the Battery compartment cover located in the back of the unit.

2. Place two new “AAA” size alkaline batteries into the Battery

compartment, correctly observing the polarity indications (+/−) inside

the compartment.

3. Replace the Battery compartment cover.

4. Press the Light button to verify LED illumination.

5. If no illumination occurs, try removing and reinstalling the batteries.

Manual code input

1. Look up the four-digit code for your brand and type of equipment in the

codelist.

2. Turn on the equipment you want the remote to control and point the

remote toward to it.

3. Press and hold the [SET] and [DEVICE] button simultaneously until the

LED keep on. Then release both of them.

4. When the LED keep on, input the four-digit code you found on the

codelist for your equipment. Each time a number is pressed, the LED

ﬂ ashes once. If LED turns off and exit the setting mode, it indicates that

your code is acceptable code. Press the [POWER] button on the remote,

if the device turns off, programming was successful. If the LED ﬂ ashes

two times and still keeps on, it indicates that the code is wrong. Then you

need to try to input others code and repeat from step 3–4 again.

5. Check whether operation of other buttons are working. If not, please

repeat step 3–4 again.

NOTE:

If no key on your remote is pressed for 30 seconds, the programming

process will exit the setting mode.

11

Manual code searching

1. Turn on the equipment you want the remote to control and point the

remote toward to it.

2. Press and hold the [SET] and [DEVICE] button simultaneously until the

LED keep on. Then release both of them.

3. When the LED keep on, press [SET] button once and release, the LED

starts ﬂ ashing every 2 seconds. It stands for entering the manual code

searching mode.

4. Aim the remote at the equipment and press the [POWER] button

repeatedly. When the equipment turns off, immediately press [DEVICE]

button to save the code and exit setup model.

5. Check whether operation of other buttons are working. If not, please

repeat from step 2 again.

NOTE:

Press [SET] button can change the searching directions.

Auto code searching

1. Turn on the equipment you want the remote to control and point the

remote toward to it.

2. Press and hold the [SET] and [DEVICE] button simultaneously until the

LED keep on. Then release both of them.

3. When the LED keeps on, press [SET] button once and release. The

LED starts ﬂ ashing every 2 seconds. It stands for entering the manual

searching mode.

4. Aim the remote at the equipment and press the [POWER] button for 3

seconds and do not release, LED will quick ﬂ ashing. It indicates entering

into the Auto code searching. Then start to release the [POWER]

button.

5. LED will ﬂ ash within every 3 seconds. When the equipment turns off,

immediately press any button to stop searching and it will back to

Manual code searching mode.

6. Press [DEVICE] button to save the code and exit the setup mode.

NOTE:

Press [SET] button can not change the searching directions.

12

Learning function setting

1. Turn on the equipment you want the remote to control and point the

remote toward to it.

2. Press and hold the [SET] and [DEVICE] button simultaneously until the

LED keeps on. Then release both of them.

3. When the LED keeps on, press the [LEARN] button once, the LED will

ﬂ ash once and turns on.

4. Point the target equipment’s remote at our remote’s learning eye

(2–5cm distance).

5. Press the corresponding button on our remote once and release, then

press the corresponding key on the target device remote, if the LED

ﬂ ashes twice on our remote, it indicates that the code was successfully

learned and saved.

6. If you need to learn others button code, please repeat the step 2–5.

7. Press [LEARN] button to exit the learning setting mode, the LED turns

off.

NOTE:

If the LED ﬂ ashes 5 times and still turns on, it indicates the code was not

learned. Please repeat step 2 – 5 again.

Any function button can learn the new code to replace the previous code

except [DEVICE], [SET], [LIGHT], [LEARN], [POWER] button.

NOTE:

If no key is pressed for 30 seconds, it will exit and return to the normal

mode.

Clear all learned key

1. Press and hold the [SET] and [DEVICE] button simultaneously until the

LED keeps on. Then release both of them.

2. Press and hold the [LEARN] button until the LED ﬂ ashes two times and

turns off. It indicates that all the learned key is clear and back to the

normal mode.

Page is loading ...

Schwaiger UFB125 User manual

Schwaiger UFB125 User manual

in other languages

Related papers

Other documents