GE ZBD5700 Installation guide

Brand: GE

Model: ZBD5700

Category: Dishwashers

Type: Installation guide

This manual is also suitable for

GE Monogram ®

Installation

Instructions

with

Optional Trim Kit

Installation Instructions

Built-In

Dishwashers

Modd._

ZBD 5600

ZBD5700

ZBD 5 900

Con_n_

gefl)re you begin - Read these instructions completely and carefldly.

IMPORTANT - Save these ii1structioi1s for local inspector's use.

IMPORTANT- OBSERVE ALL GOVERNING CODES AND ORDINANCES.

Note to Installer - Be sure to leave these instructions with tile Consmner.

Note to (:onsumer - Keep these instructions with your Use and Care Book tot flmue

i'elei'ellce.

IW:I fl This appliance must be properly grounded. See "Power Supply", page 8.

_i_R _ ;_ | [_$'_ _ iT]]_ kl| lira Cet apvareil dolt _tre correctemeut mis _ la terre.

Consulter _<Alimentation _lectrique - page 8.

If tile dishwasher is a new installation, most of

tile work must be done beflwe tile dishwasher

is moved into place. If this dishwasher is

replacing another dishwasher, tile comaections

must be checked tor compatibility and re-

placed as necessary.

If vou have a question concerning tile installa-

tion of this product, call tile GE Answer

(:enter ® Consmuer hfformation Service at

800.696.9000, 94 hours a day, 7 days a week.

If vou received a damaged dishwashei _,you

should immediately contact vom _dealer or

builder.

Installation of this dishwasher requires basic

mechanical and electrical skills. Proper

installation is tile responsibility of tile in-

staller. Product failure due to improper

installation is not covered under tile GE

Appliance _'al'rallty. See tile Use & Care

Guide for warranty infln'mation.

• This dishwasher must be installed to allow

fin" flmn'e removal ti'om tile enclosure if

service is required.

• Use this appliance only tot its intended

purpose.

For Monogram local service in your area,

1-800-444-1845.

For Monogram service in Cmlada,

1-888-880-3030.

For Monogram Parts and Accessories, call

1-800-626-2002.

• Ce lavewaisselle dolt _tre install_ de thcon

a permettre la sortie ult_riem'e de

l'enceinte en cas d'intervention,

• I1 ne flint utiliser cet appareil que pour

l'usage pore" lequel il a 6t6 construit.

Design Information

Models Available ............................................. 3

Product Dimensions ....................................... 3

Adwmce Plmming .......................................... 3

Standard Installation in 24" Deep Cabinets. 4

Optional Trim Kits ......................................... 4

Corner Installation ......................................... 4

Installation Preparation

Parts Supplied ................................................. 5

Materials You _]11 Need ................................ 6

Tools xkm Will Need ....................................... 6

Prepare tile Opening ..................................... 7

Water Supply ................................................... 7

Power Supply .................................................. 8

Prepare Drain Plmnbing ............................... 9

Installation

Step 1 Remove Wood Base .......................... 10

Step 2 Install Leveling Legs

and Toekick Brackets ................................. 10

Step 3 Install Water Inlet Fittings ................ l l

Step 4 Install Power Cord ............................ 11

Step 5 Level the Dishwasher. ....................... 12

Step 6 Slide Dishwasher into Opening ....... 19

Step 7 (kmnect _Vatei _Line ......................... 19

Step 8 Install Drain Line .............................. 13

Step 9 (kmnect Electrical ............................ 13

Step 10 Secm'e Dishwasher to

Co/mtertop or Cabinetry ........................... 14

Step l 1 Install Toekick Assembly ................ 15

Step 19 Install Side Filler Strips .................. 15

Panel Kits

ZPF25 Door Panel Kit .................................. 16

1/4" Thick Custom Door Panel

ZPF75 Door Panel Kit .................................. 19

3/4" Thick Custom Door Panel

Design Information

Stai,less Steel I, terior Dishwasher,s

Models

Available

ZBD5600 WW, ZBD5700 WW

White Dishwashers

ZBD5600 BB, ZBD5700 BB

Black Dishwashers

ZBD5900 SS

Stainless Steel Dishwasher

These dishwashers are designed for versatility,

adaptable to virtually any installation.

These models have a hill length trimless door

without the traditional access panel, The

black and white models can be customized

with decorative panels of wood or other

material.

Product

Dimensions

A-34" Min. adjustable

to 35" max.

B- 23-5/8"

C- 23-1/2" total depth

D-4" max.,2-7/8" rain.

E- 5" escutcheonheight

F- Adjustable,to 3-1/4"

G -25-1/4" from cabinets

face (dependingon depth

of cabinets)

Toekick_

Advance

Planning

• The black and white models may be covered

with custom decorative door panels of wood

or other materials to match cabinetry. See

"Optional Trim Kits," page 4.

• The stainless steel model does not accept

custom panels.

• A custom toekick can be installed to match

cabinet toekick material. A continuous

toekick may be installed to form an

unbroken line at floor level.

-A continuous toekick should be installed

in such a manner that it can be removed if

service is reqtfired.

• Tub flange trim is supplied to conceal may

slight gap between the dishwasher and

ac!jacent cabinetrv.

• These dishwashers may be installed beneath

countertops of stone or other materials that

will not accept screws. No trim kit required.

See "Secure dishwasher to cotmtertop or

ac!jacent cabinetry", page 14.

Design Inff)rmation

SlaDde,s,_ Sled l_Herior Di,_hwa,_her,_

Standard

installation

in 24" de@

cabinets

• Install in standard 24" deep cabinets:

- The dishwasher door will be flush with the

front thce of ac!jacent cabinetry.

• With a 3/4" thick custon_ door panel in

place, the exterior is trimless and fits flush

to a(!jacent cabinetry.

Cabinet

Resting

AgainstWall

01btional

7_im Kits

• ZPF25_V, white or ZPF25B, black custom

panel kit - Provides flw the installation of a

1/4" thick custom door panel, See page 16

flw installation instructions.

• ZPF75_. white or ZPF75B, black custom

panel kit - Provides flw a trimless appem_

mace using a 3/4" thick custom door panel.

See page 19 for installation instructions.

COrTler

installation

• For a corner installation, allow 2" clearai'Jce

between dishwasher and ac!jacent cabinet

or wall.

• Dishwasher nltlst be placed no more than

10 feet fl'om sink fl)i" proper drainage.

Countertop

Dishwasher

Door

Opening2" Minimum

Installation hdbrmation

Slai_less Steel Interior Dishwasher,_

Parts

Supplied

Remove the hardware accessory bag and

other parts fl'om inside or taped to the

outside of the dishwasher. Check contents

against drawings to insure that all parts are

included.

2toekick slides

2teekick support brackets

2side trim pieces

2-pieceteekick

16Screws (seeillustration}

2 leveling legs

Junction box

2 LevelingLegs

"_ Screw B

Screw A (4)SideTrim Screw C

(2)Countertop Screws (4)Toekick

Mounting Bracket

Screws Screws

Screw E Screw F

Screw D (2)Toekick (2)JunctionBox

(2)Cabinet SlideScrews- Screws

Mounting ColorMatched

Screws

FrontToekick Panel

InnerToel<ickPanel

2 PieceToekick

JunctionBox

LeftandRightSide

ToekickSupportBrackets

LeftandRightSide

ToekickSlides

2SideTrimPieces

Installation Preparation

Slai_le,s,_ Sleel I_lerior l)i,shwa,_her

MateriaLs You

Will Need:

(not supplied)

%° elbow (3/8" NPTexternal thread onone endandopposite

endto fit hotwater supply line)

Threadsealtape

ULlisted wire nuts (3)

Fer new iastallalioas ealy:

Air gapfor drain hose, if required

Waste tee for house plumbing, if applicable

Electrical cableor power cord, if applicable

Screw type hose clamps

Strain relief for electrical connection

Handshut-off valve (recommended)

Water line 3/8" O.D.min. copper or 1/2" O.D.min plastic.

Wire Nuts

Air

Gap

Electrical Cable

or PowerCord

Screw Type Clamps

HotWater Line

Waste

Tee

90° Elbow

ThreadSeal

Tape

Shut-Off

Valve

Strain Relief Coupler

7boLs you

Will Need:

(Not Supplied)

Phillipshead andflat blade screwdrivers

Adjustable wrench (6")

3/8", 5/16" and1/4" nut drivers

Level

Carpenter'ssquare

Measuringtape

Safetyglasses Safety Glasses

Flashlight

Fer new ieslallalio, only:

Tubing cutter

Drill andappropriate bits

Holesaw set

Hole

Saw Set

Adjustable

Wrench

MeasuringTape

Level

FlatBlade Screwdriver

Phillips Head

Screwdriver

Flashlight

Tubing

Cutter

Drill

and Bits

,,,,,,,,,,,i

dddddddddddd

Square

Installation Preparation

Slai_le,_,_ Sled I_Herior l)i,_hwa,sher

the

Openin, g

• The rough cabinet opening must be 24"

rain. deep, 23-5/8" rain. to 24" max. wide.

The opening height should be 34" rain.

and _5" II/ax,

• The opening should be fl'ee of extraneous

pipes and wires.

34"to35"

Underside

ofCountertop

toFloor

ThisWallArea

mustbeFreei

PipesorWires

24"Max

Water

Supply

• Hot water line may enter fl'om either side,

fl'om the rear, or fl'om the floor within the

shaded area shown.

• TtlI'n offwater supply.

• Cut a hole approximately 1-1/2" in diam-

eter to admit water line. Access hole must

be round and smooth.

• Install a hand shut-oil valve in the supply

line in an accessible location, such as under

the sink. (The shut-oil valve is optional, but

recomm ended and may be required by

local codes.)

• Install the hot water line, using no less than

3/8" O.D. copper tubing or 1/9" O.D.

plastic tubing.

• The water line must be long enough to

torm a smooth natural loop with no sharp

bends or kinks between the cutout entry

and fill valve location, centered at the fl'ont

of the dishwasher.

• At!just the water heater to deliver 120°F

rain. water temperature.

• The water pressure of the hot water supply

line must be 20 to 120 psi.

• Before connecting, flush water line to clean

otlt debris.

//J

// I

Shut-offValve

,,_

Hot ::

CabinetFace_

RightSideEntry

Approx.40"

SideEntry ...... F_

Approx.30"

fromWall 2" fromFloor

Installation Preparation

Slai_le,_,_ Steel I_Herior Di,_hwa,_her,s

FORPERSONALSAFETY:

REMOVEHOUSEFUSEOROPEN

CIRCUITBREAKERBEFOREBEGINNING

INSTALLATION.

DONOTUSEAN EXTENSIONCORDOR

ADAPTERPLUGWITHTHISAPPLIANCE

FOLLOWNATIONALELECTRICAL

CODESORPREVAiLiNGLOCALCODES

ANDORDINANCES.

.... \

/C Alternate \

/ , Receptacle t \\

, Location

SI_CURITE

ILFAUTENLEVERLEFUSIBLEDELA

MAiSONOUOUVRiRLEDISJONCTEUR

AVANTDECOMMENCER

L'INSTALLATiON.

ILNEFAUTPASUTILISERDE

RALLONGENID'ADAPTATEURDE

FICHEAVECCETAPPAREiL.[LFAUTRESPECTERTOUSLES

CODESD'ELECTRICITENATIONAUXOULESCODESET

%GLEMENTSLOCAUXENVIGUEUR.

Electrical Requirements:

These dishwashers inust be supplied with a

120 volt, 60 Hz power supply with an indi-

vidual, properly gr(mn(led branch circuit,

protected by a 15 or 20 amp filse or circuit

breaker or time delay filse.

• Wiring inust be 2 wire with gromacl.

• If electrical supply does not meet the above

requirements, call a licensed electrician

befi_re proceeding.

Grounding Instructions:

This appliance must be either cmmected to a

grounded-metal permanent wiring system, or

an equipment-grounding Coilductor must be

rim with tile circuit conductors and be

com_ected to tile equipment-grounding

terminal or lead on tile appliance.

Cabinet

Ground--/

Blacl<_

White

Cabinet Preparation & Wiring:

• Wiring may enter fl'om either side, tile rear,

or fl'om tile floor within tile shaded area

sh own.

• Cut hole 1-1/2" max. diameter within tile

shaded area to admit tile electrical cable or

power cord. Tile hole must be fl'ee of sharp

edges. If tile cabinet wall partition is metal,

tile edge of tile hole must be covered with a

rubber protector.

Electrical Connections:

Tile electrical com_ection is on tile right side

of the dishwasher.

• For cable direct com_ections, the cable inust

be routed as illustrated. The cable must

extend fi)rward a minimum of 24" fl'om the

rear wall.

• For power corcl c(mnections, install a

3-prong type receptacle in the rear wall of

sink cabinet ilext to the dishwasher. Install

the receptable at least 6" and not more than

18" fl'om the dishwasher opening. The

receptacle should be at least 6" and not

more than ] S" off tile floor.

• Allow approximately 3" between cable and

a(!jacent cabinetr v.

THEiMPROPERCONNECTIONOFTHE

EQUIPMENT-GROUNDING

CONDUCTORCANRESULTiNARiSK

OFELECTRICSHOCK.CHECKWiTHA

QUALiFiEDELECTRiCiANORSERVICE

REPRESENTATIVEiFYOUAREiN

DOUBTWHETHERTHEAPPLIANCEiS

PROPERLYGROUNDED.

LEMAUVAISBRANCHEMENTDU

CONNECTEURDEMISEALATERREDE

L'EQUIPEMENTPEUTCAUSERUN

RISQUED'ELECTROCUTION.ENCASDE

DOUTESURLAMISEALATERREDE

L'APPAREIL,CONSULTERUN

ELECTRICIENQUALIFIEOUUN

PREPOSEDESERVICE.

Installation Preparation

Slai_le,_,_ Sled I_lerior Di,_hwa,sher

drain

plumbin, g

• Follow local codes and ordinances.

• Dishwasher drain hose must not exceed 10

feet in length for proper drainage.

- Tire dishwasher is supplied with a 3/4"

I.D. drain hose, 78" long. Add tip to 42"

length to the fhctory supplied hose if

necessaiw.

• Dishwasher must be comaected to waste line

Mth an air gap (not supplied) or 30"

minimum, high drain loop (depending on

local codes and ordinances) to prevent

back flow into the dishwasher.

• An air gap must be used if waste tee or

disposer com_ection is less than 12" above

floor to prevent siphoning.

• Install waste tee or disposer and air gap

according to the manufilcturer's instruc-

tions.

• Cut a hole in cabinet wall, approximately

1-1/2" in diameter for drain hose.

• Install drain hose hook to underside of

countei'top.

An air gap MUST BE USED if the drain

hose is connected to x_aste tee or disposer

lower than 12" aboxe the floor lexel.

Failure to provide the proper drain con-

necti(m height, 12", with air gap or 30"

minim um high drain loop will result in

improper draining of the dishwasher which

IIlav catlse dalnage.

! i I

IL DOlT YAVOIR un dispositif anti-retour

si le tuwm de vidange est branch_ hun tO

d'_gout ou fi un broveur d'ordures qui est _l

Illoins de 30 cI/l (12 po) atl-(lesstls (hi sol.

Si le tuyau d'_)gout n'est pas branch,) h une

bom'Je hauteur, au moiFJs 30 cm (12 po),

avec un dispositif anti-retour, ou si la

boucle d'()gout haute n'est pas {i une

hauteur d'au moins 75 cm (30 po), le

lave-vaisselle se vidange real, ce qui petit

causer des d&gfits.

Method 1 - Air Gap with Waste Tee or Disposer

Usethis methodwhen waste tee or disposerconnection is less

than 12" abovethe floor.

Waste Tee Installation

DisposerInstallation

Method2- HighDrainLoop

with WasteTeeorDisposer

Usethismethodwhenhighdrainloopisat least30"abovethe

floor.

WasteTeeInstallation

-- 4-

DisposerInstallation

Installation

StaD_le,s,_ Steel I_Herior Di,_hwa,_her

hi,stall Custom

Door Panel

• If you intend to install custom door panels,

refer to installation instructions provided in

this booklet. The panels should be in place

beIore installing the dishwasher.

Step l

Remove

wood base

Cut the shipping carton and use it as a pad

trader the dishwasher, This will protect the

finished floor in the kitchen,

• Lay the dishwasher on its back,

• Remove the 4 screws holding the dish-

washer to the wood base. Discard screws.

• Retain wood base,

• lnsm'e that the floor of the cutout is the

same level or higher than the rest of the

room. If the kitchen floor is tile, it may be

elevated above the floor of the installation

cutout. Pieces of the wood base may be

placed into the cutout floor to make it level

or higher than with the kitchen floor, This

will allow fin" easy rein oval fl_r any fllture

service,

St@ 2

Install

_velin, g legs

& toekick

brackets

• Un-wrap the drain hose and pull to the rear

of the dishwasher, Take care not to kink or

crush the hose.

• Install toekick support brackets on the left

and right sides of the mounting brackets

using 2 screws each, See illustration for

correct orientation,

• Install the fl'ont leveling legs provided in

the parts package. The legs should be at

least 2" fl'om the bottom edge of the

motmting bracket.

• A({just leveling legs to installation height.

Tighten leveling leg locking nuts on the

rear.

Screw C

2" Min.

Mounting Bracket

Toekick Support Bracket

Installation

Slai_le,vs Sleel I_lerior Di,shwa,sher

Step 3

Install

Water Inlet

Fittin,_s

• Install the 90 ° elbow onto the water inlet.

Use thread sealing tape or pipe thread

C()IIlp()/lI1 d,

• The 90 ° elbow should tace the left or right

side, depending on water line routing.

st@ 4

Install

powocord

(g" used)

Skipthis step

Ifdishwasher

will bewired

direct.

• Install strain relief ontojmaction box and

tighten against incoming wires.

• Strip 1/2" insulation fl'om end of power

cord wires.

• Comaect incoming wires to dishwasher wires

using wire mlts of appropriate size.

• Comaect tile white to white, black to black

and incoming gro/md to green wire.

• Push all wires into thejm_ction box and

secm'e cover with screws onto dishwasher

ti'all/e.

Note: Tile power cord and connections II/[Ist

comply with tile National Electrical Code,

Section 429 and/or local codes and

ordinances.

IMPORTANT: The p(mer cord illt/st be no

longer than 6 fl fl'om thejmlction box to tile

plug. DO NOT PLUG IN PO_ ER CORD .AT

THIS TIME.

ScrewF

Installation

StaD_le,s,_ Steel I_lerior Di,_hwa,_her

Step 5

Level the

Dishwasher

• Careflllly upright tile dishwasher, taking

care not to bend tile leveling legs. Make

sure tile leveling leg locking nuts are

sectlre.

• Check to be sure tile dishwasher is level and

at tile cutout height.

Level

And

Sides

Step6

Slide

Dishwasher

Into Openin, g

• Insert drain hose into tile hole previously

drilled in tile cabinet wall.

• Slide tile dishwasher into tile opening a few

inches at a time.

• As you proceed, pull tile drain hose

through tile cabinet wall under tile sink.

• If a power cord is used, guide tile end

through a separate hole.

• Check to be sure there is no interference

with waterline or house wiring.

Step 7

Connect

Water Line

• Tile water supply line should be flushed to

clear any foreign material before connect-

ing to tile dishwasher.

• Make sure there are no sharp bends or

kinks which could restrict tile water flow.

90° Elbow

HotWater

Supply

Installation

Slaiule,vs Sleel Iulerior Di,shwa,sher

Step 8

[nstall

Drain Line

• Follow all local codes and ordinances.

Drain Line Preparation

• The dishwasher is supplied with a 78" hmg

corrugated drain hose.

• If the location requires a longer draiil hose,

add up to 42" length to the supplied hose.

Use 3/4" inside diameter hose and thin

wall copper coupler to join the hose ends.

Note: Total drain hoselength must notexceed 10feet for

properdrain operation.

Drain Line Installation

• (_om_ect drain line to air gap, waste tee or

disposer using either method 1 or 2 as

previously determined.

• SecHre c(mnection using appropriate

clamps (not supplied).

• Make sm'e drain hose is not kinked.

Note: Removedrain plug beforeconnectingto disposer.

Dishwashercannotdrain if plug is left in place.

Method1 - AirGapwith WasteTeeorDisposer

Waste Tee Installation

DisposerInstallation

Method 2 - High Drain Loop

with Waste Tee or Disposer

Fasten to underside

__ ofcountertop

30" 30"

Waste Teelnstallation Disposerlnstallation

Step9

Connect

Electrical

(Fordirect

connectionto

housewiring)

lf housewiring is not2-wire with a

__ groundwire, a groundmust be provided

by the installer. When housewiring is

aluminum, besureto useU.L.listed

anti-oxidant compoundand aluminum-

to-copperconnectors.

Si lecircuit de la maison n'a pasdeux

ills, plus unfil deterre, Vinstallateur

dolt installer unfil deterre. Quandles

ills de la maison sent en aluminium, il

faut prendresoin d'utiJiser une p_te

anti-oxydante et des connecteurs

aluminium acuivre surla liste UL.

Screw F

Verify that power is turned off at the source.

• Install a strain relief onto the junction box

and tighten against the incoming wires.

• Strip l/2" insulation fl'om end of incoming

wires.

• Use wire mlts of appropriate size and c(m-

nect white t()white, black to black and

incoming ground to green wire.

• Push all wires into the junction box and

place on dishwasher fl'ame. Secure with

screws "g".

Installation

Stai_less Steel I_Herior Dishwasher

Step 10

5 cure

Dishwasher

to Countertop

or Cabinetry

To maintain position and alignment the

dishwasher nlust be secured to tile COUlltertop

or to a(!jacent cabinetry.

If co/mtertop is of stone or other hard

material, secure the dishwasher to a(!jacent

cabin ets.

• Check to be s/ire that dishwasher is a(!justed

to correct height and is centered in tile

cutout.

• Open and close dishwasher door to insure

proper operation of tile door. If there is anv

binding or rubbing, reac!just leveling legs.

Secure dishwasher to countertop:

• Drill pilot holes through tile mounting

bracket and into tile underside of tile

countertop. Install 2 screws "A" provided.

Note: Take special care to ensure

CO/lllterI//O/lIlt screws are driven flush so thev

do not damage top of do()); when door is

closed.

Secure dishwasher to adjacent cabinets:

• Remove plastic plug buttoi_ on tile inside of

the dishwasher fl'ame. One (hi each side.

• Drill pilot holes through tile holes and into

the ac!jacent cabinets, Install 2 screws "D"

provided.

• Replace plastic plug buttons.

Screw D

Installation

Slai_le,s,s Sleel I_lerior l)i,shwa,sher

Step l l

[nstall

7bekick

Assembly

• Install toekick slides to toekick support

brackets. Use slide stamped "L" on left and

"R" on right side.

• Align fl'ont and ironer toekicks, matching

screw holes.

• Align toekick to second screw hole in

toekick slide as illustrated.

• Install color matched screws "E" through

the flxmt of the toekick and into the toekick

slides. Do not tighten screws.

• Carefldly, slide assembly back until it is

aligned with a(!jacent cabinetry toekick.

• A(!just the height of the panel by loosening

screws and sliding the fl'ont panel down,

even x_ith the floor.

• Carefully, hold the door and open flflly.

Ensure that door does not strike top of

toekick.

• A(!just toekick height if necessary.

• Tighten screws.

FrontToel<icl<Panel

InnerToel<icl<

LeftSide

Toekicl<

Slide

ScrewE

Slide out_toekick

AttachmentScrews

Pulltab while

Pushingtoekickin

St@ 12

Install

Side 7?ira

• Side trim filler strips are packed with this

dishwasher. If the cabinet cutout is wider

than the dishwasher, install the filler strips

on both sides of the dishwasher to cover

gaps.

• Open the door fidlv.

• Place side trim against dishwasher tub and

install 2 screws, loosely on each side.

• At!just trim to correct width. Tighten screws.

Side

Trim

Screw B

ZPF25 Custom Door Panel Kit

l/4" Tkick (u,slom Door Pa_el

7, 5

ZPI_2r B, Black trim

cF_ r

ZPF2, _,, White trim

Tools and Materials required

• Phillips screwdriver

• Glovesto protect againstsharp edges.

To pre_ent electrical shock,

clisc(mnect electrical pox_er

supply to dishwasher before

changing panels. Do not

operate dishwasher when

door asseinblv is i'ei/love(l.

Moto: It isbestthat 2 peopleperformthis installation.

The ZPF25 trim kit provides support for 1/4"

thick custoln door panel.

Moto: Maximumcustompanelweightis

10pounds.

Pore" &viter les

&lectrocutions, il flint

cl_brancher l'alimentation

&lectriq ue du lave-vaisselle

event de changer les

pam_eaux. I1 ne thut pas

thire follctiollller le lave-

vaisselle q uand la porte est cl&pos&e.

Kit Contents

• Metal door

• 8 wood screws

• 6 "6" clips

• DoorTrim

• 2 Door Springs (8)Screws

DoorTrim

"(;" Olips

2Door

Springs

St@ l

Cut l/4"

Thick Custo"nz

Panel to Size

• Cut door panel to the dimensions shown.

• The bottom left and right corners should

be cut at 1/4" radius. See illustration.

Rote: Thetrim will conceal thecut edgesof the panels.

1/4" Thick

DoorPanel

23-1/8"

25-1/2"

ZPF25 Custom Door Panel Kit

l/4" Tkick (ustom Door Pa_el

Step 2

Remove

Existin, g

Metal Door

• Open the door fllllv.,

Caution: One person should hold the door

while the other backs out s('rex_s to prex eat

the metal door fron/falling.

• Remove 6 screws on the inside the inner

door fl'ame, Retain screws,

• Remove the 2 screws with o-rings located in

the bottom center of the ironer door. Retain

screws and o-rings.

• [x)eIuove the ()liter door,

• Remove the 2 screws holding the center

door bracket to metal door,

• Retain bracket and insulation,

• Discard metal door,

Step 3

Assemble

Panel to

Door

• Place the supplied metal door Oll a fiat

s/li't_lce,

• Place the custom panel on top of the metal

door.

• Place supplied trim over the custom panel.

• Press trim to panel and install the color

matched screws provided. Install 3 screws

on each side and 9 screws on the bottom.

DoorTrim

Deco Panel

_orPanel

s@ 4

[nstall Door

C_nter

Bracket

• Turn the assembled door over with appear-

ance side down,

• Install center door bracket onto door using

original screws,

• Place insulation around support bracket,

Insulation

Install Screws

ZPF25 Custom Door Panel Kit

l/4" Tkick Custom Door Pa_el

Step 5

fnstall

As sembled

Door onto

Dishwasher

• Locate the "(7' clips in the parts package.

Place one clip, flat side tip, oxer each of the

screw holes, 3 on each side of the door.

Note: Onepersonshould hold the doorwhile the other installs

screwsto preventthe door assemblyfrom falling.

• Hold the assembled door to dishwasher

ironer door and slide tip against control

panel. Control panel has posts that should

engage the 9 holes in the top of the metal

door.

• Install the original center screws and

o-rings.

Note: Centerscrewsand o-rings must besecurelyfastened to

preventfuture leaks.

• Install original screx_ s to sides of imaer door

flame, 3 each side.

Step 6

[nstall

Door

5 rincs

The additional weight of the custom panel

may require that the heavy door springs be

installed.

Test Door Balance

• With one hand under the door, slowly open

the door filllv.

• Open and close the door to check t0r

proper balance. Correct door balance

should prevent the door fl'om raising by

itself fl'om a fifll open position and prevent

the door fl'om talling heavilv.

• If the door talls heavil}; damage will occur

ti'om repeated use.

• Install one or both new springs provided.

Install New Springs:

• Close and latch the dishwasher door.

• Locate door spring on left side of dish-

washer.

• Disengage the push rod guide by pushing

down on the guide and slowly pulling the

guide out of the mounting position.

• Carefldly release the tension on the spring

and remove the push rod guide fl'om the

rod.

• Remove the spring and replace with the

spring that has a yellow marking,

• Reassemble the push rod guide into the

original position,

• Test door balance,

• Install right side spring if needed,

ZPF75 Custom Panel Kit

/4 Thick (usi0m l)oor Panel

ZPF75B, Black

ZPF75_, _ hite

Tools and Materials mqu#ed

• Phillips screwdriver

• Glovesto protect against sharp edges

• Nut driver

_To prexent electrical shock,

discmmect electrical power

supply to dishwasher

befin'e changing panels.

Do not operate dishwasher

when door assembly is

reiilo','ed.

Note: It is best that 2 people perform this installation.

The ZPF75 provides fin" the installation of

1/2" to 3/4" thick custom door panel.

Noto: Maximumcustompanelweight is

10pounds.

Pour &viter les

_)lectrocutions, il thut

d_)brancher l'alimentation

_lectrique du lave-vaisselle

avant de changer les

pmmeaux. I1 ne thut pas

thire tinactimmer le lave-

vaisselle quand la porte est d6pos6e.

Kit Contents

• Metal door

• Support bracket

• Label

• 18Screws

• 2 Doorsprings

Metal Door

Screw Y

Screw X (6) Not Used Screw Z

(1O)Wood Screws (2)Support Bracket

Screws

Door Springs

Support

Bracket

St@ l:

Determine

Custom

Panel

Sizes

The custoin panel should be constructed in

the same nlanner as cabinet doors. All edges

can be seen and must be finished for the best

appearance.

C0untert0p Custom

__ , Panel Size Top

-t

Cabinets Dim A_' 3/4"Thick

Door Panel _Height

F Floor _ll_-

/ Bottom of 3/4" Max. _23-1/8"

Adjacent Cabinetry

_Height is equalto A minus 5-1/8" plus 1/4"

EXAMPLE:

_Height =30-1/2" minus5-1/8" plus 1/4" is equal to 25-5/8".

• Measm'e dimension A, fl'om underside of

countertop to bottom of ac!jacent cabinets.

- Subtract 5-1/8". Control panel height is 5".

Allow 1/8" fin" gap between bottom of

countertop and top of control panel.

-Add 1/4". The custom panel will slide tip,

behind control panel.

ZPF75 Custom Panel Kit

/4 Thick ( u,stom Door Panel

Step 2

Remove

Existing

Metal Door

• Open tile door flflly.

Caution: Oneperson shouldhold the doorwhile the other

hacksout screwsto preventthe metal doorfrom falling.

• Remove 6 screws on tile inside of tile

fi'ame. Retain screws.

• Remove tile 2 screws with o-rings located in

tile bottom center of tile door. Retain

screws and o-rings.

• Renlove tile door.

• Remove insulation and loam inserts,

discard metal door.

2 "0" Rings

Step 3

[nstall Door

Center Bracket

• Install new center door bracket onto door

using screws "Z'.

• Place insulation aroui]d support bracket.

ScrewZ

Supp!_:_!_acl<et

2-Depresslons_Fla t Face

Metallntegrated Door

Step4

Assemble

Custo' z"n

Pand

• Lay custom panel (m a fiat surtace, appear-

ance side down.

• Place tile new metal door panel onto tile

back of tile custom door panel. Align sides

and top edges.

• Drill 1/8" pilot holes, 3/8" deep, through

the metal panel and into tile custom panel,

3 each side.

• Secure custonl panel to metal door with

3 screws "X" on each side.

• Drill 1/4" pilot holes through tile top

return flange, approximately 1/4" deep.

Drill 1/8"Holes

(3 EachSide)

Drill 1/4"

Holes

ScrewX

_mPanel

Page is loading ...

GE ZBD5700 Installation guide

Brand: GE

Model: ZBD5700

Category: Dishwashers

Type: Installation guide

This manual is also suitable for

Download PDF

report

GE ZBD5700 Installation guide

This manual is also suitable for

GE ZBD5700 Installation guide

Related papers

Other documents