Goldstar MV1735B Owner's manual

Brand: Goldstar

Model: MV1735B

Category: Microwaves

Type: Owner's manual

Website: http://us.lgservice.com

CAUTION

SAFETY PRECAUTIONS

PRECAUTIONS TO BE OBSERVED BEFORE AND

DURING SERVICING TO AVOID POSSIBLE EXPOSURE

TO EXCESSIVE MICROWAVE ENERGY

a. Do not operate or allow the oven to be operated with the door open.

b. Make the following safety checks on all ovens to be serviced before activating the

magnetron or other microwave source, and make repairs as necessary; (1) Interlock

operation, (2) proper door closing, (3) seal and sealing surfaces (arcing, wear, and

other damage), (4) damage to or loosening of hinges and latches, (5) evidence of

dropping or abuse.

c. Before turning on microwave power for any service test or inspection within the

microwave generating compartments, check the magnetron, wave guide or

transmission line, and cavity for proper alignment, integrity, and connections.

d. Any defective or misadjusted components in the interlock, monitor, door seal, and

microwave generation and transmission systems shall be repaired, replaced, or

adjusted by procedures described in this manual before the oven is released to the

owner.

e. A Microwave leakage check to verify compliance with the Federal Performance

Standard should be performed on each oven prior to release to the owner.

• Proper operation of the microwave ovens requires that the magnetron be assembled to the

wave guide and cavity. Never operate the magnetron unless it is properly installed.

• Be sure that the magnetron gasket is properly installed around the dome of the tube whenever

installing the magnetron.

• Routine service safety procedures should be exercised at all times.

• Untrained personnel should not attempt service without a thorough review of the test

procedures and safety information contained in this manual.

FOREWORD

Read this Manual carefully. Failure to adhere to or observe the information in this Manual may result in exposing

yourself to the Microwave Energy normally contained within the oven cavity.

TABLE OF CONTENTS

(Page)

SAFETY PRECAUTIONS ......................................................................................................... Inside front page

SPECIFICATIONS.......................................................................................................................................... 1-1

CAUTIONS..................................................................................................................................................... 2-1

INSTALLATIONS............................................................................................................................................ 3-1

OPERATING INSTRUCTIONS....................................................................................................................... 4-1

CONTROL PANEL ................................................................................................................................. 4-1

CONTROL PANEL INSTRUCTIONS ..................................................................................................... 4-2

OVERALL CIRCUIT DIAGRAM...................................................................................................................... 5-1

SCHEMATIC DIAGRAM......................................................................................................................... 5-1

MATRIX CIRCUIT FOR TOUCH KEY BOARD...................................................................................... 5-2

GENERAL INFORMATION FOR SERVICE................................................................................................... 6-1

GENERAL PRECAUTIONS IN USE ...................................................................................................... 6-1

TRIAL OPERATION ............................................................................................................................... 6-1

FEATURES AND SPECIFICATIONS FEATURES................................................................................. 6-1

SERVICE INFORMATION ............................................................................................................................. 7-1

PRECAUTIONS AND REPAIR SERVICE TIPS..................................................................................... 7-1

MICROWAVE LEAKAGE TEST............................................................................................................. 7-2

POWER OUTPUT MEASUREMENT ..................................................................................................... 7-3

DISASSEMBLY INSTRUCTIONS .......................................................................................................... 7-4

INTERLOCK SYSTEM .......................................................................................................................... 7-12

INTERLOCK CONTINUITY TEST.......................................................................................................... 7-14

TEST AND CHECKOUT PROCEDURES AND TROUBLE SHOOTING................................................ 7-15

A. TEST PROCEDURES................................................................................................................ 7-15

B. CHECKOUT PROCEDURES..................................................................................................... 7-18

C. TROUBLE SHOOTING.............................................................................................................. 7-21

EXPLODED VIEW.......................................................................................................................................... 8-1

REPLACEMENT PARTS LIST............................................................................................................... 8-8

SCHEMATIC DIAGRAM OF PCB .......................................................................................................... 8-14

PRINTED CIRCUIT BOARD .................................................................................................................. 8-15

PCB PARTS LIST................................................................................................................................... 8-16

1-1

Rated Power Consumption 1,500W maximum (Microwave oven only)

Microwave Output

1000W (IEC 60705)

Adjustable 100W through 1000W, 10 steps

Frequency 2,450 MHz

50 MHz

Power Supply 120 VAC, 60 Hz

Rated Current 13 Amp. (Microwave oven+Cook top lamps+Ventilation fan)

Magnetron Cooling Forced Air Cooling

Rectification Rectification Voltage Double Half-Wave

Door Sealing Choke System

Safety Devices Magnetron Thermal Fuse:

Open at 109

Oven Cavity Thermostat:

Open at 110

Fuse(20A)

Primary Interlock Switch

Secondary Interlock Switch

Interlock Monitor

Magnetron 2M248J

High Voltage Capacitor Capacitor: 1.0µF, 2.1 KV AC

High Voltage Diode Diode; 350mA, 9.0 KV

Cook top Lamp 125 V, 30 W or 40 W

Cavity Lamp 125 V, 30 W

Timer Digital, up to 99 mim. 99 sec. (in each cooking stage)

Tray Tempered Safety Glass

Overall Dimensions 29

/16”(W)x16

/16”(D)x15

/2”(H)

Effective Capacity of Oven Cavity 1.7 Cu.ft.

Accessories Owner’s Manual & Cooking Guide, Installation Manual,

Exhaust Adapter, Exhaust Damper, Mounting Kit and Two

Filters, Rotating Ring Assembly, Metal Rack.

SPECIFICATIONS

2-1

CAUTIONS

• DO NOT operate on a 2-wire extension cord during

repair and use.

• NEVER TOUCH any oven components or wiring during

operation.

• BEFORE TOUCHING any parts of the oven, always

remove the power plug from the outlet.

• For about 30 seconds after the oven stops, an electric

charge remains in the high voltage capacitor. When

replacing or checking, you must discharge the high

voltage capacitor by shorting across the two terminals

with an insulated screwdriver.

•

Remove your watches whenever working close to or

replacing the Magnetron.

• DO NOT touch any parts of the control panel circuit. A

resulting static electric discharge may damage this

P.C.B.

• NEVER operate the oven with no load.

• NEVER injure the door seal and front plate of the oven

cavity.

• NEVER put iron tools on the magnetron.

• NEVER put anything into the latch hole and the interlock

switches area.

• Proper operation of the microwave oven requires that

the magnetron be assembled to the waveguide and

cavity. Never operate the magnetron unless it is

properly installed.

• Be sure that the magnetron gasket is properly

installed around the dome of the tube whenever

installing the magnetron.

Unlike other appliances, the microwave oven is

high-voltage and high-current equipment.

Though it is free from danger in ordinary use,

extreme care should be taken during repair.

THE OVEN IS TO BE SERVICED ONLY

BY PROPERLY QUALIFIED SERVICE

PERSONNEL.

MICROWAVE RADIATION

Personnel should not be exposed to the

microwave energy which may radiate from the

magnetron or other microwave generating

device if it is improperly used or connection.

All input and output microwave connections,

waveguide, flange, and gasket must be secure

never operate the device without a microwave

energy absorbing load attached.

Never look into an open waveguide or antenna

while the device is energized.

Gasket

ANTENNA

COOLING FIN

MAGNETRON

CHASSIS GROUND

FILAMENT

TERMINALS

MAGNETRON

3-1

INSTALLATIONS

PRECAUTIONS ON INSTALLATION

A. Plug the power supply cord into a 120V AC, 60Hz,

single-phase power source with a capacity of 15A

or 20A.

B. Avoid placing the unit in a location where there is

direct heat or splashing water.

C. Install the unit on the mounting plate firmly.

D. Place the unit as far away as possible from TV,

radio, etc. to prevent interference.

GROUNDING INSTRUCTIONS

For personal safety, this appliance must be fully

grounded at all times.

In the event of an electrical short circuit, grounding

reduces the risk of electrical shock.

The plug must be plugged into an outlet that is

properly installed and grounded.

BEFORE YOU BEGIN, READ THE FOLLOWING INSTRUCTIONS COMPLETELY AND CAREFULLY.

WARNING

Improper use of the grounding plug can result in a

risk of electric shock.

Do not, under any circumstances, cut or remove the

third ground prong from the power cord plug.

CAUTION

This unit is equipped with a 3-prong plug for your

safety. If the wall outlet is a grounded 3-hole type,

the unit will be grounded automatically.

Plug with Ground

Prong

Properly Polarized

and Grounded

Outlet

CONTROL PANEL

4-1

OPERATING INSTRUCTIONS

One Touch Control

POPCORN

PIZZA

CLOCK HELP

PO TATO

REHEAT

BEVERAGE

COOK

CUSTOM

COOK

LIGHT

TIMER

CUSTOM

SET

HOLD

WARM

AUTO

DEFROST

KITCHEN

TIMER

LESS

STOP/

CLEAR

Ez OnSTART

TURNTABLE

On/Off

VENT

Hi/Low/Off

LIGHT

Hi/Low/Off

POWER

LEVEL

TIME

COOK

123

456

789

CONTROL PANEL INSTRUCTIONS

4-2

1. DISPLAY: The display includes a clock and indicators to

tell you time of day, cooking time settings, and cooking

functions selected.

2. MORE: Press this pad to add ten seconds of cooking time

each time you press it.

3. LESS: Press this pad to subtract ten seconds of cooking

time each time you press it.

4. CLOCK(TIME OF DAY): Press this pad to enter the time

of day.

5. HELP: Press this pad to learn how to use each oven

function.

6. ONE TOUCH CONTROL: Press these keys let you cook

foods easily.

7. NUMBER: Press number pads to enter cooking time,

power level, quantities, or weights.

8. POWER LEVEL: Press this pad to select a cooking power

level.

9. TIME COOK: Press this pad followed by Numper Pads to

set a cooking time.

10. STOP/CLEAR: Press this pad to stop the oven or to

clear all entries.

11. START: Press this pad to start a function. If you open

the door after oven begins to cook, START again.

12. EZ ON: Press this pad to cook for 30 seconds at 100%

power level.

13. CUSTOM SET: Press this pad to change the oven’s

default settings for sound, clock, display speed, defrost

weight, and demo mode operations.

14. HOLD WARM: Press this pad to keep hot, cooked foods

safely warm in your microwave oven for up to 99 minutes

99 seconds.

15. AUTO DEFROST: Press this pad to select food type and

defrost food by weight.

16. CUSTOM COOK: Press this pad to recall one cooking

instruction previously programmed into memory.

17. LIGHT TIMER: Press this pad to set the light timer.

18. KITCHEN TIMER: Press this pad to set the kitchen

timer.

19. TURNTABLE ON/OFF: Press this pad to turn off the

turntable. OFF will appear in the display.

20. VENT HI/LOW/OFF: Press this pad to turn the fan on or

off.

21. LIGHT HI/LOW/OFF: Press this pad to turn on the

cooktop/countertop light.

5-1

MODEL

SCHEMATIC DIAGRAM

OVERALL CIRCUIT DIAGRAM

MATRIX CIRCUIT FOR TOUCH KEY BOARD

78654321

POPCORN

VENT

H/L/OFF

HELP

POTATO

LIGHT

H/L/OFF

CUSTOM

SET

CUSTOM

COOK

678 90

BEVERAGE

EZ ON

CLOCK

HOLD

WARM

POWER

LEVEL

KITCHEN

TIMER

LIGHT

TIMER

PIZZA

START

STOP/

CLEAR

TIME

COOK

AUTO

COOK

AUTO

REHEAT

AUTO

DEFROST

LESS

N.C N.C N.C

N.CN.C N.C

TURNTABLE

ON/OFF

5-2

6-1

GENERAL PRECAUTIONS IN USE

A. Never operate the unit when it is empty.

Operating the oven with no load may shorten the

life of the magnetron. Whenever cooking dry foods

(dried fish, bread, etc.) or a small amount of food,

be sure to put a glass of water into the cooking

compartment. The glass turntable may become hot

after operating, be careful when touching it.

B. Aluminum foil should be avoided because it will

disrupt cooking and may cause arcing. However,

small pieces may be used to cover some parts of

food to slow the cooking. Any aluminum foil used

should never be closer than 2.5 cm to any side wall

of the oven.

TRIAL OPERATION

After installation, the following sequences and results

should be checked carefully.

A. Put a container filled with water (about 1 liter) into

the oven, and close the door tightly.

B. Set cooking time for 10 minutes by touching “1”

and then “0” three times. “1, 0, 0, 0” appears in

the display window.

C. Touch the START key.

Make sure the cavity light comes on. The unit will

begin cooking and the display window will show the

time counting down by seconds.

D. After about 5 minutes, make sure the primary

interlock switch, the secondary interlock switch and

the interlock monitor switch operate properly by

opening and closing the door several times. Touch

the START key each time the door is closed.

E. Continue operating the unit. Four long beep sound

signal is heard when the time is up. The unit will

shut off automatically.

F. Confirm the water is hot.

G. Finally, measure the output power according to

“POWER OUTPUT MEASUREMENT” on

page 7-3.

FEATURES AND SPECIFICATIONS

FEATURES

A. The safety systems incorporated in this model are:

(1) Primary interlock switch

(2) Secondary interlock switch

(3) Interlock monitor switch

(4) Choke system

(5) Magnetron thermal fuse

(6) Oven cavity thermostat

(Note: This thermostat located on the oven

cavity will open and stop the unit from operation

only if a high temperature is reached, such as,

a fire created by overcooking food.)

B. Any one of 10 power output levels ranging 100W to

1000W can be selected by the touch control and

electronic computer system.

GENERAL INFORMATION FOR SERVICE

PRELIMINARY

A. SINCE NEARLY 2,100 VOLTS EXISTS IN SOME

CIRCUITS OF THIS UNIT REPAIRS SHOULD BE

CARRIED OUT WITH GREAT CARE.

The filament leads of magnetron carry High

Voltage with respect to ground. Extreme caution

must be exercised. Never plug the unit into a

power source to determine which component is

defective in high voltage section.

B. TO AVOID POSSIBLE EXPOSURE TO

MICROWAVE ENERGY LEAKAGE, THE

FOLLOWING PRECAUTIONS MUST BE TAKEN

BEFORE SERVICING.

(1) Before the power is applied:

(a) Make sure the primary interlock switch, the

secondary interlock switch and the interlock

monitor switch operate properly by opening

and closing the door several by opening and

closing the door several times.

(b) Make sure the perforated screen and the

dielectric choke of the door are correctly and

firmly mounted.

(2) After power is applied:

(a) Make sure the interlock switch mechanism

is operating properly by opening and closing

the door.

(b) Check microwave energy leakage must bebelow

the limit of 5 mW/cm

(All service adjustments should be made for

minimum microwave energy leakage

readings).

(3) Do not operate the unit until it is completely

repaired, if any of the following conditions exist.

The unit must not be operated.

(a) The door does not close firmly.

(b) The hinge is broken.

(d) The door is bent or warped, or there is any

other visible damage on the unit that may

cause microwave energy leakage.

NOTE: Always keep the seal clean.

(e) Make sure that there are no defective parts

in the interlock mechanism.

(f) Make sure that there are no detective parts

in the microwave generating and transmission

assembly (especially waveguide).

(4) The following items should be checked after the

unit is repaired:

(a) The interlock monitor switch is connected

correctly and firmly.

(b) The magnetron gasket is properly positioned

and mounted.

(no microwave energy leakage)

(d) The door can be properly closed and the

safety switches work properly.

(e) The unit must stop when the door is opened or

the time is up.

The unit must not be operated with any of the above

components removed or by-passed.

7-1

PRECAUTIONS AND REPAIR SERVICE TIPS

SERVICE INFORMATION

7-2

CAUTIONS

• Be sure to check microwave leakage prior to

servicing the oven if the oven is operative prior to

servicing.

• The service personnel should inform the

manufacture importer, or assembler of any certified

oven unit found to have a microwave emission level

in excess of 5 mW/cm

and should repair any unit

found to have excessive emission levels at no cost to

the owner and should ascertain the cause of the

excessive leakage. The service personnel should

instruct the owner not to use the unit until the oven has

been brought into compliance.

• If the oven operates with the door open, the service

personnel should:

- Tell the user not to operate the oven.

- Contact the manufacturer and CDRH

(Center for Devices and Radiological Health)

immediately.

NOTE: Address on CDRH

Office of Compliance(HFZ-312)

Center for Devices and Radiological

Healthe 1390, Piccard Drive,

Rockville. MD 20850

• The service personnel should check all surface and

vent openings for microwave leakage.

• Check for microwave leakage after every servicing. The

power density of the microwave radiation leakage

emitted by the microwave oven should not exceed

4 mW/cm

. Always start measuring of an unknown field

to assure safety for operating personnel from radiation

leakage.

EQUIPMENT

• TESTER (VOLTS-DC, AC, Ohmmeter)

• Microwave survey meter

- Holaday HI-1500

HI-1501

- Narda 8100

8200

• 600 cc non conductive material beaker (glass or

plastic), inside diameter: approx. 8.5 cm (3

/2 in.)

• Glass thermometer: 100°C or 212°F (1 deg scale)

MEASURING MICROWAVE ENERGY

LEAKAGE

• Pour 275±15cc of 20±5°C(68±9°F) water in a beaker

which is graduated to 600 cc, and place the beaker

on the center of the turntable.

• Set the energy leakage monitor to 2,450 MHz and

use it following the manufacturer's recommended

test procedure to assure correct result.

• When measuring the leakage, always use the 2-inch

(5cm) spacer supplied with the probe.

• Operate the oven at its maximum output.

• Measure the microwave radiation using and

electromagnetic radiation monitor by holding the

probe perpendicular to the surface being measured.

Move probe along shaded area.

Probe scanning speed

Less than 2.5 cm/sec. ( 1 in/sec)

MICROWAVE LEAKAGE TEST

MEASUREMENT WITH THE OUTER CASE

REMOVED

(1) When you replace the magnetron, measure for

microwave energy leakage before the outer case

is installed and after all necessary components

are replaced or adjusted. Special care should be

taken in measuring the following parts.

- Around the magnetron

- The waveguide

WARNING: AVOID CONTACTING ANY HIGH

VOLTAGE PARTS.

MEASUREMENT WITH A FULLY

ASSEMBLED OVEN

(1) After all components, including the outer

panels, are fully assembled, measure for

microwave energy leakage around the door

viewing window, the exhaust opening and air

inlet openings.

(2) Microwave energy leakage must not exceed the

values prescribed below.

NOTES:

Leakage with the outer panels removed - less

than 5 mW/cm

Leakage for a fully assembled oven (“Before the

latch switch (primary) is interrupted”) with the door

in a slightly opened position - less than 2 mW/cm

NOTE WHEN MEASURING

(1) Do not exceed meter full scale deflection.

(2) The test probe must be removed no faster than

1 inch/sec (2.5cm/sec) along the shaded area,

otherwise a false reading may result.

(3) The test probe must be held with the grip portion

of the handle. A false reading may result if the

operator’s hand is between the handle and the

probe.

(4) When testing near a corner of the door, keep

the probe perpendicular to the surface making

sure the probe horizontally along the oven

surface, this may possibly cause probe damage.

RECORD KEEPING AND NOTIFICATION

AFTER MEASUREMENT

(1) After adjustment and repair of any microwave

energy interruption or microwave energy blocking

device, record the measured values for future

reference. Also enter the information on the

service invoice.

(2) Should the microwave energy leakage not be

more than 2 mW/cm

after determining that all

parts are in good condition, functioning properly

and genuine replacement parts which are listed in

this manual have been used.

(3) At least once a year, have the electromagnetic

energy leakage monitor checked for calibration

by its manufacturer.

(1)

Microwave power output measurement is made with

the microwave oven supplied at its rated voltage and

operated at its maximum microwave power setting

with a load of (1000±5) g of potable water.

(2)

The water is contained in a cylindrical borosilicate

glass vessel having a maximum material thickness of

1/8” (3 mm) and an outside diameter of

approximately 7.6” (190mm).

(3)

The oven and the empty vessel are at ambient

temperature prior to the start of the test.

(4)

The initial temperature (T1) of the water is (10±2)°C

(50°F) It is measured immediately before the water is

added to the vessel. After addition of the water to the

vessel, the load is immediately placed on the center

of the turntable which is in the lowest position and the

microwave power switched on.

(5)

The time T for the temperature of the water to rise by

a value ∆ T of (10±2)°K is measured, where T is the

time in seconds and ∆T is the temperature rise. The

initial and final water temperatures are selected so

that the maximum difference between the final water

temperature and the ambient temperature is 5°K.

(6)

The microwave power output P in watts is

calculated from the following formula :

4187 x (∆T)

is measured while the microwave generator is

operating at full power. Magnetron filament heat-up

time is not included. (about 3 sec)

(7)

The water is stirred to equalize temperature

throughout the vessel, prior to measuring the final

water temperature.

(8)

Stirring devices and measuring instruments are

selected in order to minimize addition or removal of

heat.

7-3

WATER LOAD

TURNTABLE

P =

POWER OUTPUT MEASUREMENT

IMPORTANT NOTES:

UNIT MUST BE DISCONNECTED FROM ELEC-

TRICAL OUTLET WHEN MAKING REPAIRS, RE-

PLACEMENTS, ADJUSTMENTS AND CONTIN-

UITY CHECKS. WAIT AT LEAST ONE MINUTE,

UNTIL THE HIGH VOLTAGE CAPACITOR IN THE

HIGH VOLTAGE POWER SUPPLY HAS FULLY

DISCHARGED.

THE CAPACITOR SHOULD BE DISCHARGED BY

USING INSULATED WIRE - I.E. TEST PROBE

CONNECTED TO 10K-OHM RESISTOR IN SERIES

TO GROUND.

WHEN RECONNECTING THE WIRE LEADS TO

ANY PART, MAKE SURE THE WIRING CONNE-

CTIONS AND LEAD COLORS ARE CORRECTLY

MATCHED ACCORDING TO THE OVERALL CIR-

CUIT DIAGRAM. (ESPECIALLY SWITCHES AND

HIGH VOLTAGE CIRCUIT.)

A. REMOVING POWER AND CONTROL

CIRCUIT BOARD (Figures 1, 2 and 3)

(1) Remove a screw securing the control panel

assembly to the oven cavity.

(2) Remove the control panel with pushing it upward.

(3) Remove the three connectors (CN1, CN2) and

wire leads (Relay2) from the circuit board.

(4) Remove 3 screws securing the circuit board.

(5) Remove the FPC connector from the terminal

socket following “HOW TO REMOVE THE FPC

CONNECTOR” on the next page.

(6) Remove the circuit board from the control bracket

carefully.

7-4

Circuit Board

FPC Connector(S1)

Control Bracket

Circuit Board

Figure 1

Figure 2

Figure 3

DISASSEMBLY INSTRUCTIONS

Control Panel

Screw

Power

Transformer

Relay 2

(CN2)

(Relay 2)

(CN1)

7-5

HOW TO REMOVE THE F.P.C. CONNECTOR

Follow the steps below as illustrated in Figures 4

and 5 to remove the F.P.C. connector.

(1) Hold the edges of the plastic fastener with

thumb and forefinger.

(Figure 4)

(2) Lift up the lever of the plastic fastener from

the terminal socket by lightly pressing the

lever end with forefinger.

(Figure 5)

(3) Remove the F.P.C. connector from the

terminal socket.

HOW TO INSERT THE F.P.C. CONNECTOR

Follow the steps below as illustrated in Figures 6

and 7 to insert the F.P.C. connector.

(1) Insert the F.P.C. connector into the terminal

socket securely with the fingers.

(2) Hold the plastic fastener with thumb and

forefinger of the other hand, and push it

slowly into the terminal socket. (Figure 6)

NOTE: When reconnecting the F.P.C

connector make sure that the holes

on the F.P.C. connector are properly

engaged with the hooks on the plastic

fastener

(3) Lock the level of the plastic fastener into the

hook of the terminal socket securely by

releasing the fingers.

(Figure 7)

Terminal

socket

Terminal

socket

F.P.C.

Connector

F.P.C.

Connector

Plastic fastener

Holes

Hook

Plastic fastener

Plastic

fastener

Terminal

socket

F.P.C.

Connector

Terminal

socket

F.P.C.

Connector

Plastic fastener

Holes

Hook

Figure 4

Figure 7

Figure 6

Figure 5

B. REMOVING THE OUT CASE(Figure 8)

(1) Remove the vent grille by removing two screws

securing it to the out case.

(2) Remove two screws securing it to the air duct.

(3) Remove the mounting plate by turning the screws

(1 or 2 screws) securing it to the out case.

(4) Remove two screws on the left central edge and

one screws on the right central edge of Base

plate. Remove the Mount, All from the out case by

removing one screw securing it to the out case.

(5) Remove the outcase with disconnecting power

cord connector.

Vent Grille

Controller

(3 screws)

Door

Mounting

Plate

(1 or 2 screws)

Out Case

Mount,All

Figure 8

7-6

7-7

C REMOVING THE DOOR INTERLOCK

SWITCHES (Figures 9,10)

(1) Disconnect the wire leads from the interlock

switches.

(2) Remove two screws securing the Latch Board.

(3) Make necessary replacements and check

microwave energy leakage according to

“ADJUSTMENT PROCEDURE” on page 7-12.

Latch Board

Secondary

Interlock Switch

Interlock

Monitor Switch

Primary

Interlock Switch

Latch Board

(from H.V.Transformer)

(

from Fan Motor

)

(

from Power Cord)

(

from cooktop lamp

)

Secondary Interlock Switch

Monitor Interlock Switch

Primary Interlock Switch

PK(from P.C.B)

(

from P.C.B)

(from H.V.Transformer)

Figure 9

Figure 10

WIRE COLOR

SYMBOL COLOR

N.P.

WHITE

BLACK

BROWN

RED

BLUE

PINK

GREY

Not Provided

D. REMOVING MAGNETRON

(Figures 11 Through 13)

(1) Remove the vent grille by loosening two screws.

(Figure 11)

(2) Remove the outcase. See page 7-6.

(3) Remove three tap tite screws securing the

magnetron to the wave guide.

(4) Remove the magnetron VERY CAREFULLY.

NOTES:

• When removing the magnetron, make sure that its

dome does not hit any adjacent parts, or it may be

damaged.

• When replacing the magnetron, be sure to install the

magnetron gasket in the correct position and be sure

that the gasket is in good condition.

• After replacing the magnetron, check for microwave

energy leakage with a survey meter Check

microwave energy leakage must be below the limit

of 5 mW/cm

. (All service adjustments should be

made for minimum microwave energy leakage

readings.)

Figure 11

Figure 13

7-8

Figure 12

Vent Grille

Controller

(3 screws)

Door

Mounting

Plate

(1 or 2 screws)

Out Case

Mount,All

E. REMOVING STIRRER FAN

(Figures 14 and 15)

(1) Remove one rivet ASS'Y securing it to the oven

upper plate by using knife blade.

(2) Rotate slightly and pull out the stirrer fan cover.

(3) Remove the stirrer fan.

F. REMOVING DOOR (Figure 16)

(1) Remove the vent grille by two screws securing it to

the outcase loosening.

(2) Lift up and draw the door.

G. DISASSEMBLING DOOR (Figure 17)

(1) Remove the dielectric choke by using knife

blade or small screw driver, etc.

(2) Remove two screws securing it to the door handle.

CAUTION: Be careful not to damage door seal

plate with the screwdriver.

NOTES:

• After replacing the door, be sure to check that the

primary interlock switch, the secondary interlock

switch and the interlock monitor switch is in good

operating normally.

• After replacing the door, check for microwave energy

leakage with a survey meter. Microwave energy

leakage must be below the limit of 5mW/cm

. (With a

275 ml water load)

7-9

Door Screen

Figure 15

Figure 14

Figure 17

Figure 16

Page is loading ...

Goldstar MV1735B Owner's manual

Brand: Goldstar

Model: MV1735B

Category: Microwaves

Type: Owner's manual

Download PDF

report

Goldstar MV1735B Owner's manual

Goldstar MV1735B Owner's manual

Related papers

Other documents