Broadcast Tools 2×6 DA Plus Owner's manual
- Category
- Musical Equipment
- Type
- Owner's manual
This manual is also suitable for
Installation and Operation Manual
PROBLEM SOLVED
Due to the dynamic nature of product design, the information contained in this
document is subject to change without notice. Broadcast Tools, Inc., assumes no
responsibility for errors and/or omissions contained in this document. Revisions
of this information or new editions may be issued to incorporate such changes.
Broadcast Tools® is a registered trademark of Broadcast Tools, Inc.
All Sentinel® labeled products are registered trademarks of Broadcast Tools, Inc.
Copyright® 1989 - 2015 by Broadcast Tools, Inc. All rights reserved.
No part of this document may be reproduced or distributed without permission.
Visit www.broadcasttools.com for important product update information.
Manual update: 6/16/2015
If you need a firmware upgrade, contact Broadcast Tools®
No part of this document may be reproduced or distributed without permission.
ALL SPECIFICATIONS AND FEATURES FOR THIS PRODUCT ARE SUBJECT TO
CHANGE WITHOUT NOTICE
NOTE: We recommend the use of Chrome, Firefox or Safari as your browser.
2x6 DA Plus
2X3 or 1x6 Distribution Amplifier
INC
®
2x6 DA Plus Installation and Operation Manual
Table of Contents
Section Title . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page #
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Who to Contact for Help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Product Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Features/Benefits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Installation/Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Surge Protection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
UPS standby power system . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
LED indicators. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Input connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Input Level switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Audio Output connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Stereo/Monaural Jumper Settings . . . . . . . . . . . . . . . . . . . . . . . 6
Output Level adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Front and rear panel drawings . . . . . . . . . . . . . . . . . . . . . . . . Appendix
Connector and configuration jumper layout . . . . . . . . . . . . . Appendix
Fractional schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Appendix
WEBSITE:
Visit our web site for
product updates and
additional information.
2
CONTENTS
3
2x6 DA Plus Installation and Operation Manual
INTRODUCTION
INTRODUCTION
Thank you for your purchase of the 2x6 DA Plus Stereo Distribution Amplifier,
which we will refer to throughout the manual as the 2x6 DA Plus. We’re confident
this product will give you many years of dependable service. This manual is intend-
ed to give you all the information needed to install and operate the BROADCAST
TOOLS® 2x6 DA Plus
SAFETY INFORMATION
Only qualified technical personnel should install the 2X6 DA PLUS. Any attempt
to install this device by a person who is not technically qualified could result in a
hazardous condition to the installer or other personnel or damage to the 2X6 DA
PLUS or other equipment. Please ensure that proper safety precautions have been
taken before installing this device. If you are unfamiliar with this type of equipment,
please contact a properly qualified engineer to handle the installation and setup of
the 2X6 DA PLUS. Broadcast Tools, Inc., is unable to support NON-Broadcast
Tools software, hardware or NON-Broadcast Tools computer/hardware/software
problems. If you experience these problems, please research your hardware/software
instruction manuals or contact the manufacturers technical support department.
WHO TO CONTACT FOR HELP
If you have any questions regarding your product or you need assistance, please con-
tact your distributor from whom you purchased this equipment. If you would like
more information about BROADCAST TOOLS® products, you may reach us at:
Broadcast Tools, Inc.
131 State Street
Sedro-Woolley, WA 98284-1503 USA
Voice: 360.854.9559
Fax: 866.783.1742
Internet Home Page: www.broadcasttools.com
E-mail:[email protected]
THANK YOU FOR CHOOSING
BROADCAST TOOLS® BRAND PRODUCTS!
CAUTION!
Broadcast Tools®
Products, as with any
electronic device, can
fail without warning.
Do not use this product
in applications where a
life threatening condition
could result due to failure.
NOTE:
This manual should be
read thoroughly before
installation and operation.
WEBSITE:
Visit our web site for
product updates and
additional information.
Broadcast Tools is a Veteran Owned Business
Designed, Assembled and Supported in WA State, USA
4
2x6 DA Plus Installation and Operation Manual
OVERVIEW
Product Overview
The 2x6 DA Plus stereo distribution amplifier is equipped with a stereo line level
high-Z input, which accepts a balanced or unbalanced source with six active bal-
anced low-Z output amplifiers. Each output amplifier may be paired for stereo oper-
ation or each output pair may be summed for monaural operation without affecting
the stereo separation of the other outputs. Each output amplifier has a recessed front
panel level control trimmer.
Features/Benefits
• Stereo or monaural output set via jumpers.
• Front panel output level trimmers.
• Switch selectable input gain for –10dBV or +4dBU sources, eliminating the
need for external level conversion.
• Removable euro-block screw terminal connectors are used for audio con-
nections. Necessary mating plugs are supplied.
• Fully RFI proofed.
• Surge protected internal power supply, PS-1515 universal switching +/-
15VDC power supply with domestic connectors supplied. International AC
connectors optional.
• Up to three units may be mounted on the optional RA-1 rack shelf. Desktop
and wall mounting is also possible.
Inspection
Please examine your 2X6 DA PLUS carefully for any damage that may have been
sustained during shipping. If any damage is present, please notify the shipper imme-
diately and retain the packaging for inspection by the shipper. The package should
contain the 2X6 DA PLUS, and a +/-15 VDC wall power supply with domestic con-
nector. Manuals may be downloaded from our web site.
WEBSITE:
Visit our web site for
product updates and
additional information.
5
2x6 DA Plus Installation and Operation Manual
INSTALLATION
Installation/Operation
Power
Connect the supplied PS-1515 power supply’s 3-pin AMP-style latching power con-
nector to the unit and the +/-15 VDC switching power supply with domestic con-
nector into a 120 Vac 50-60 Hz power source. The Power+ and Power- LEDs will
light to indicate proper supply voltage.
NOTE: Never use any type of power supply other than the specified/supplied power
supply.
Surge Protection
The 2X6 DA PLUS has built-in resistance to voltage changes; we recommend that
you use a power surge protector or line conditioner on the incoming AC line.
Lightning strikes and/or other high voltage surges may damage your 2X6 DA PLUS
and connected equipment if it is not properly protected. For lightning protection
devices, check out www.polyphaser.com and www.itwlinx.com.
UPS Standby Power System
We recommend that you connect your 2X6 DA PLUS to a UPS system. A UPS helps
minimize the risk to the 2X6 DA PLUS and provides power during a power outage.
LED indicators
• “Power+” and “Power-“ LEDs: Indicate positive and negative power supply.
• “LT Act” and “RT Act” LEDs: Indicate left and right audio input activity.
Input Connection
Connect your audio source to the DA’s 5-position input terminal block. The input is
labeled: “INPUT” “L-“ “L+” for the left channel and “R-“ “R+” for the right chan-
nel. Connect the cable shields to G (ground) connection. For unbalanced inputs,
install a jumper between the "-" input and G (ground). Single (mono) inputs may be
fed to all output channels by connecting the left and right inputs in parallel.
NOTE: Please verify proper phasing.
Input Level Switch
The input on the 2x6 DA Plus can be switched between two gain ranges using the
rear panel “Input Level” switch. With the switch in the +4 dBu “in” position the
input gain is set to accept a +4 dBu nominal signal. With the switch in the -10 dBu
“out” position 12 db of gain is added to the input to accommodate consumer/low line
level input signals.
WEBSITE:
Visit our web site for
product updates and
additional information.
6
2x6 DA Plus Installation and Operation Manual
INSTALLATION
Audio Output Connections
The 2x6 DA Plus provides balanced analog stereo outputs on three pluggable 5-posi-
tion euro-block style connectors. The output level is adjustable via front panel 1-turn
trimmers labeled 1-6. Connect each load to the 2 x 6 DA outputs, labeled "OUT-
PUTS 1L-/1L+, 2L-/2L+ and 3L-
/3L+". For unbalanced loads, use the "+" and GND terminals only. Do not connect
the "-" terminal to ground. Shields should be tied to the “GND” terminals.
Stereo/Monaural Jumper Settings
Each stereo output can be set to output a monaural sum of the left and right input
audio. Follow the silk-screened “Mono” labels on the PCB. If the jumper is
installed, that output will be combined to monaural. Placing a jumper over JP1 con-
verts output one to mono, JP2 output two and JP3 addresses output three. The fac-
tory setting is Stereo. The three stereo outputs operate independently; setting one
output pair to MONO has no effect on the other pairs, and does not degrade the
integrity of the other stereo outputs.
Output Level Adjustment
Use the front panel left (LT) and right (RT) level adjustment trimmers to set each
output channel to the desired output level.
WEBSITE:
Visit our web site for
product updates and
additional information.
7
2x6 DA Plus Installation and Operation Manual
SPECIFICATIONS
SPECIFICATIONS
Input Level: -10dBv or +4dBu nominal. Switch selectable. +24dBu max, @ 600 Ω
Input Impedance: 20K Ω balanced, 10 K Ω unbalanced
Output Level: +4dBu nominal, + 24dBu max, @ 600 Ω, balanced
Output Impedance: 100 Ω balanced, 47 Ω unbalanced
System Gain: 20 dB
Frequency Response: +/- 0.2dB (20Hz – 20kHz)
Noise: 75 dB below nominal
Power: PS-1515 universal switching power supply with domestic AC
connector supplied. International AC connectors optional.
+/-15 VDC 400mA output with 3-pin AMP-style latching power
connector.
Dimensions: 6 x 5.25 x 1.63 in (W x L x H)
Options: RA-1 Rack Shelf. 1 RU. Accommodates up to 3 units.
PS-1515-500/IEC, AC line cord not supplied.
WEBSITE:
Visit our web site for
product updates and
additional information.
8
2x6 DA Plus Installation and Operation Manual
LIMITED WARRANTY
LIMITED WARRANTY
The term “Buyer” as used in this document refers to and includes both (but only) (a) any person or entity who acquires such an item for
the purpose of resale to others (i.e., a dealer or distributor of an item), and (b) the first person or entity who acquires such an item for
such person’s or entity’s own use.
Broadcast Tools warrants to each Buyer of any item manufactured by Broadcast Tools that the item will be free from defects in materi-
als and workmanship at the time it is shipped by Broadcast Tools if the item is properly installed, used and maintained.
EXCLUSIVE REMEDIES
If Broadcast Tools is notified, in writing, of a failure of any item manufactured by Broadcast Tools to conform to the foregoing Limited
Warranty within one (1) year following the date of the Buyer’s acquisition of the item, and if the item is returned to Broadcast Tools in
accordance with Broadcast Tools’ instructions for confirmation by inspection of the defect (which at Broadcast Tools’ election may
include, without limitation, a requirement that the Buyer first obtain a Return Authorization number from Broadcast Tools, that the Buyer
furnish proof of purchase in the form of an invoice and/or receipt, and that the Buyer prepay all freight charges associated with any return
of the item to Broadcast Tools using such freight service as Broadcast Tools reasonably may specify), Broadcast Tools will repair or
replace the defective item, or will refund the purchase price paid by the Buyer for the item. Broadcast Tools shall have the exclusive
right to choose between these alternative remedies.
NO OTHER WARRANTIES OR REMEDIES
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, BROADCAST TOOLS AND ITS SUPPLIERS DISCLAIM ALL OTHER
WARRANTIES, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABIL-
ITY OR FITNESS FOR A PARTICULAR PURPOSE; AND THE FOREGOING ALTERNATIVE REMEDIES SHALL BE EXCLUSIVE OF
ALL OTHER REMEDIES. THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY HAVE OTHER RIGHTS,
WHICH VARY FROM STATE/JURISDICTION TO STATE/JURISDICTION.
NO LIABILITY FOR CONSEQUENTIAL DAMAGES
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, NEITHER BROADCAST TOOLS NOR ANY OF ITS SUPPLIERS
SHALL HAVE ANY LIABILITY FOR ANY SPECIAL, INCIDENTAL, INDIRECT, CONSEQUENTIAL OR PUNITIVE DAMAGES WHATSO-
EVER (INCLUDING, WITHOUT LIMITATION, ANY DAMAGES FOR LOST PROFITS, BUSINESS INTERRUPTION, LOSS OF DATA OR
INFORMATION, COST OF CAPITAL, CLAIMS OF CUSTOMERS, OR ANY OTHER PECUNIARY LOSS) ARISING OUT OF THE USE
OF OR THE INABILITY TO USE ANY ITEM SUPPLIED BY BROADCAST TOOLS, EVEN IF BROADCAST TOOLS HAS BEEN
ADVISED OF THE POSSIBILITY OF SUCH DAMAGES HAVE ANY LIABILITY FOR ANY SPECIAL, INCIDENTAL, CONSEQUENTIAL,
EXEMPLARY OR PUNITIVE DAMAGES. THIS LIMITATION OF LIABILITY APPLIES WHETHER A CLAIM IS ONE ALLEGING
BREACH OF A CONTRACT OR WARRANTY, NEGLIGENCE OR OTHER TORT, FOR THE VIOLATION OF ANY STATUTORY DUTY,
THE FAILURE OF ANY LIMITED OR EXCLUSIVE REMEDY TO ACHIEVE ITS ESSENTIAL PURPOSE, OR ANY OTHER CLAIM OF
ANY NATURE. BECAUSE SOME STATES AND JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY
FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES, THIS LIMITATION MAY NOT APPLY TO YOU.
Broadcast Tools, Inc.
131 State Street
Sedro-Woolley, WA 98284 • USA
360.854.9559
voice • 866.783.1742 fax
suppor[email protected] e-mail
www.broadcasttools.com website
2x6 DA Plus Installation and Operation Manual
9
APPENDIX
Product_Name Installation and Operation Manual
10
APPENDIX
Product_Name Installation and Operation Manual
11
APPENDIX
Product_Name Installation and Operation Manual
12
APPENDIX
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
Broadcast Tools 2×6 DA Plus Owner's manual
- Category
- Musical Equipment
- Type
- Owner's manual
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Broadcast Tools ACT-2 Owner's manual
-
-
-
-
-
-
-
-
-