Chief K1C1I2B Installation guide
- Category
- Mounting kits
- Type
- Installation guide
INSTALLATION INSTRUCTIONS
Instrucciones de instalación
Installationsanleitung
Instruções de Instalação
Istruzioni di installazione
Installatie-instructies
Instructions d´installation
K1 Single Column with iPad®2/iPad®3 Mount
Spanish Product Description
German Product Description
Portuguese Product Description
Italian Product Description
Dutch Product Description
French Product Description
K1C1I2B
K1C1I2B Installation Instructions
2
DISCLAIMER
Milestone AV Technologies and its affiliated corporations and
subsidiaries (collectively "Milestone"), intend to make this
manual accurate and complete. However, Milestone makes no
claim that the information contained herein covers all details,
conditions or variations, nor does it provide for every possible
contingency in connection with the installation or use of this
product. The information contained in this document is subject
to change without notice or obligation of any kind. Milestone
makes no representation of warranty, expressed or implied,
regarding the information contained herein. Milestone assumes
no responsibility for accuracy, completeness or sufficiency of
the information contained in this document.
Chief® is a registered trademark of Milestone AV Technologies.
All rights reserved.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: A WARNING alerts you to the possibility of
serious injury or death if you do not follow the instructions.
CAUTION: A CAUTION alerts you to the possibility of
damage or destruction of equipment if you do not follow the
corresponding instructions.
WARNING: Failure to read, thoroughly understand, and
follow all instructions can result in serious personal injury,
damage to equipment, or voiding of factory warranty! It is the
installer’s responsibility to make sure all components are
properly assembled and installed using the instructions
provided.
WARNING: Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the combined weight of
all components located between the K1C1I2B up to (and
including) the display does not exceed 25 lbs (11.34 kg).
WARNING: Use this mounting system only for its intended
use as described in these instructions. Do not use
attachments not recommended by the manufacturer.
WARNING: Never operate this mounting system if it is
damaged. Return the mounting system to a service center for
examination and repair.
WARNING: Do not use this product outdoors.
--SAVE THESE INSTRUCTIONS--
DIMENSIONS
12.50
317.5
Installation Instructions K1C1I2B
3
LEGEND
Tighten Fastener
Apretar elemento de fijación
Befestigungsteil festziehen
Apertar fixador
Serrare il fissaggio
Bevestiging vastdraaien
Serrez les fixations
Loosen Fastener
Aflojar elemento de fijación
Befestigungsteil lösen
Desapertar fixador
Allentare il fissaggio
Bevestiging losdraaien
Desserrez les fixations
Phillips Screwdriver
Destornillador Phillips
Kreuzschlitzschraubendreher
Chave de fendas Phillips
Cacciavite a stella
Kruiskopschroevendraaier
Tournevis à pointe cruciforme
Open-Ended Wrench
Llave de boca
Gabelschlüssel
Chave de bocas
Chiave a punte aperte
Steeksleutel
Clé à fourche
By Hand
A mano
Von Hand
Com a mão
A mano
Met de hand
À la main
Hex-Head Wrench
Llave de cabeza hexagonal
Sechskantschlüssel
Chave de cabeça sextavada
Chiave esagonale
Zeskantsleutel
Clé à tête hexagonale
Pencil Mark
Marcar con lápiz
Stiftmarkierung
Marcar com lápis
Segno a matita
Potloodmerkteken
Marquage au crayon
Drill Hole
Perforar
Bohrloch
Fazer furo
Praticare un foro
Gat boren
Percez un trou
Adjust
Ajustar
Einstellen
Ajustar
Regolare
Afstellen
Ajuster
Remove
Quitar
Entfernen
Remover
Rimuovere
Verwijderen
Retirez
Optional
Opcional
Optional
Opcional
Opzionale
Optie
En option
Security Wrench
Llave de seguridad
Sicherheitsschlüssel
Chave de segurança
Chiave di sicurezza
Veiligheidssleutel
Clé de sécurité
K1C1I2B Installation Instructions
4
TOOLS REQUIRED FOR INSTALLATION
PARTS
#2
1/8" (included)
3/16" (included)
A (1)
E (1)
[arm assembly]
B (1)
[adapter plate]
[iPad interface]
J (1)
3/16"
K (1)
1/8"
C (4)
M4x12mm
D (4)
M4x12mm
F (4)
M4x12mm
G (4)
M4x20mm
H (4)
M4
Installation Instructions K1C1I2B
5
Assembly And Installation
Connecting Arm Assembly to Desk
Standard Installation
1. Loosen clamp screw until enough space is created between
clamp and mount to allow for desk mounting.(See Figure 1)
NOTE: If space is limited behind desk (i.e. against wall, etc.),
remove clamp screw and attachment entirely and
reattach clamp screw prior to Step 3! (See Figure 2)
2. Place mount on top of desk at desired mounting location.
(See Figure 1)
3. Tighten clamp using clamp screw until mount is securely
fastened to desk. (See Figure 1)
Figure 1
Figure 2
Low Profile Installation
1. Remove top cap from column. (See Figure 3)
2. Slide mount assembly off of column. (See Figure 3)
Figure 3
3. Rotate mount 90 degrees in either direction prior to
reinstalling onto column. (See Figure 4)
4. Reinstall onto column and adjust to desired height. (See
Figure 4)
5. Reinstall top cap to column. (See Figure 4)
Figure 4
1
2
3
desk
1
2
3
4
5
K1C1I2B Installation Instructions
6
iPad2®/iPad3® Installation
1. Remove quick release faceplate from arm assembly (A) by
pressing quick release tab and sliding faceplate off mount.
(See Figure 5)
Figure 5
2. Use four M4x12mm Phillips pan machine screws (D) to
connect faceplate to adapter plate. (See Figure 6)
Figure 6
3. Reinstall faceplate to mount.
4. Use four M4x12 Phillips flat head screws (C) to connect
iPad® interface (E) to adapter plate (B). (See Figure 7)
Figure 7
IMPORTANT ! : The K1C1I2B is designed specifically for
use with the iPad®2 or iPad®3. Other portable tablet
devices may not fit properly into the interface.
5. Fit the iPad® into the interface (E), bottom edge first. (See
Figure 8)
6. Angle the iPad® back while pressing back on the locking
tab of the mount. (See Figure 8)
7. Fit the top edge of the iPad® under the tab. (See Figure 8)
Figure 8
quick release tab
1
1
2
(D) x 4
faceplate
(A)
2
(C) x 4
(E)
(B)
5
7
6
Installation Instructions K1C1I2B
7
8. To release the iPad® from the mount, firmly hold the iPad®
while pressing back on the tab to release and remove the
iPad®. (See Figure 9)
Figure 9
9. Position iPad® with faceplate attached above mount. (See
Figure 10)
10. Slide faceplate onto mounting head until quick release tab
clicks into place. (See Figure 10)
Figure 10
Adjustments
Column Height Adjustment
1. Loosen column adjustment knob. (See Figure 11)
2. Adjust height to desired level. (See Figure 11)
3. Tighten column adjustment knob. (See Figure 11)
Figure 11
Pivot Adjustment Range
1. Adjust arm angle as desired up to 90 degrees in either
direction. (See Figure 12)
WARNING: Swinging the arm beyond 90 degrees may
result in the mount slipping off the desk causing serious
injury!
Figure 12
10
1
3
2
(top view)
+/- 90 degrees range
of motion
edge of desk or wall face
K1C1I2B Installation Instructions
8
Head Tilt Adjustment
1. Adjust head tilt to desired tilt position. (See Figure 13)
2. Adjust head tilt tension screw to change the adjustment
tension. (See Figure 13)
Height Adjustment
1. Adjust height to desired level. (See Figure 13)
2. Open cable management cover on upper arm to expose
height-adjustable tension screw. See Cable Management
section for details.
3. Use 1/8" hex key (K) to adjust height-adjustable tension
screw to change adjustment tension. (See Figure 13)
4. Close cable management cover on upper arm. See Cable
Management section for details.
Pivot Adjustment
1. Adjust pivot position as desired. (See Figure 13)
2. Use 3/16" hex key (J) to adjust pivot point tension screws to
change pivot adjustment tension. (See Figure 13)
Figure 13
Portrait Adjustment
The iPad® may be adjusted 90 degrees in either direction in
order to provide a portrait view of the iPad®.
Figure 14
Cable Management
1. Route cables through cable management channel on upper
arm. (See Figure 15)
Figure 15
pivot point
tension
height-adjustable tension
head tilt tension
cable (typical)
1
Installation Instructions K1C1I2B
9
K1C1I2B Installation Instructions
10
Installation Instructions K1C1I2B
11
K1C1I2B Installation Instructions
USA/International A 6436 City West Parkway, Eden Prairie, MN 55344
P 800.582.6480 / 952.225.6000
F 877.894.6918 / 952.894.6918
Europe A Franklinstraat 14, 6003 DK Weert, Netherlands
P +31 (0) 495 580 852
F +31 (0) 495 580 845
Asia Pacific A Office No. 1 on 12/F, Shatin Galleria
18-24 Shan Mei Street
Fotan, Shatin, Hong Kong
P 852 2145 4099
F 852 2145 4477
Chief Manufacturing, a products division
of Milestone AV Technologies
8800-002197 Rev00
2012 Milestone AV Technologies, a
Duchossois Group Company
www.chiefmfg.com
06/12
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
Chief K1C1I2B Installation guide
- Category
- Mounting kits
- Type
- Installation guide
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Chief K0W1I2B Installation guide
-
-
-
-
-
Chief MIWRF6000B Specification
-
-
-
Chief K1C110B Installation guide
-
Other documents
-
Novus 961+0119+000 Datasheet
-
Chief Manufacturing MSP-DARKWE/CE/CD/PZ-110 User manual
-
Atdec VTB-FD Installation guide
-
Twelve South 12-2021 Owner's manual
-
Twelve South HoverBar User guide
-
-
Enabling Devices 1587 User manual
-
Enabling Devices 1589X User manual
-
-
Sanus VMD1 Installation guide
