Schumacher 00-99-000940-0110 User manual

00-99-000940/0110

Models / Modelos / Modèles: INC-406A & INC-406AC

Automatic Battery Charger / Cargador de batería

automático / Chargeur de batterie automatique

READ THE ENTIRE MANUAL BEFORE USING THIS PRODUCT. •

FAILURE TO DO SO CAN RESULT IN SERIOUS INJURY OR DEATH.

LEA EL MANUAL COMPLETO ANTES DE UTILIZAR ESTE •

PRODUCTO. CUALQUIER FALLA PODRÍA RESULTAR EN SERIAS

LESIONES O PODRÍA SER MORTAL.

LIRE ENTIÈREMENT LE GUIDE AVANTD’UTILISER CE PRODUIT. •

L’ÉCHEC DE FAIRE AINSI PEUT S’ENSUIVRE DANS LA BLESSURE

SÉRIEUSE OU LA MORT.

OWNER’S MANUAL•

MANUAL DEL USUARIO•

GUIDE D’UTILISATION•

Voltage / Tensión / Tension: 6, 12

Amperage / Amperaje / Ampérage: 6

™

Page is loading ...

TABLE OF CONTENTS

SECTION PAGE

IMPORTANT SAFETY INSTRUCTIONS 2

PERSONAL PRECAUTIONS 2

PREPARING TO CHARGE 3

CHARGER LOCATION 4

DC CONNECTION PRECAUTIONS 4

FOLLOW THESE STEPS WHEN BATTERY IS INSTALLED

IN VEHICLE. 4

FOLLOW THESE STEPS WHEN BATTERY IS OUTSIDE VEHICLE. 5

BATTERY CHARGING – AC CONNECTIONS 5

ASSEMBLY INSTRUCTIONS 6

MOUNTING INSTRUCTIONS 6

CONTROL PANEL 7

OPERATING INSTRUCTIONS 7

CALCULATING CHARGE TIME 8

MAINTENANCE INSTRUCTIONS 9

STORAGE INSTRUCTIONS 9

TROUBLESHOOTING 9

REPLACEMENT PARTS 10

BEFORE RETURNING FOR REPAIRS 10

LIMITED WARRANTY 11

ÍNDICE

SECCIÓN PÀGINA

INSTRUCCIONES IMPORTANTES DE SEGURIDAD 13

PRECAUCIONES PERSONALES 14

PREPARACIÓN PARA LA CARGA 14

UBICACIÓN DEL CARGADOR 15

PRECAUCIONES DE CONEXIÓN EN CC 15

SIGA ESTOS PASOS CUANDO LA BATERÍA ESTÉ COLOCADA

EN EL VEHÍCULO. 16

SIGA ESTOS PASOS CUANDO LA BATERÍA SE ENCUENTRE

FUERA DEL VEHÍCULO. 16

CARGA DE BATERÍA, CONEXIONES DE CA 17

INSTRUCCIONES DE MONTAJE 17

INSTRCCIONES PARA EL MONTAJE 18

PANEL DE CONTROL 18

INSTRUCCIONES DE OPERACIÓN 19

CÁLCULO DE TIEMPO DE CARGA 20

INSTRUCCIONES DE MANTENIMIENTO 21

INSTRUCCIONES DE ALMACENAJE 21

LOCALIZACIÓN Y SOLUCIÓN DE PROBLEMAS 21

REPUESTOS 22

ANTES DE DEVOLVER A REPARACIONES 22

GARANTÍA LIMITADA 23

TABLE DES MATIÈRES

PARTIE PAGE

CONSIGNES DE SÉCURITÉ IMPORTANTES 25

PRÉCAUTIONS PERSONNELLES 25

PRÉPARATION POUR LE CHARGEMENT 26

EMPLACEMENT DU CHARGEUR 27

PRÉCAUTIONS SUR LA CONNEXION C.C. 27

ÉTAPES À SUIVRE QUAND LA BATTERIE EST INSTALLÉE

DANS UN VÉHICULE. 27

ÉTAPES À SUIVRE QUAND LA BATTERIE EST INSTALLÉE

HORS DU VÉHICULE. 28

CHARGEMENT D’UNE BATTERIE – RACCORDEMENTS C.A. 29

DIRECTIVES DE MONTAGE 29

INSTRUCTIONS DE MONTAGE 29

PANNEAU DE CONTRÔLE 30

CONSIGNES D’UTILISATION 31

CALCUL DU TEMPS DE CHARGEMENT 32

CONSIGNES D’ENTRETIEN 32

DIRECTIVES D’ENTREPOSAGE 33

TABLEAU DE DÉPANNAGE 33

PIÈCES DE RECHANGE 34

AVANT DE L’ENVOYER POUR RÉPARATION 34

GARANTIE LIMITÉE 35

• 1 •

IMPORTANT: READ AND SAVE THIS SAFETY AND INSTRUCTION MANUAL.

SAVE THESE INSTRUCTIONS – The INC-406A and INC-406AC offer a wide

range of features to accommodate your needs. This manual will show you how

to use your charger safely and effectively. Please read, understand and follow

these instructions and precautions carefully, as this manual contains important

safety and operating instructions. The safety messages used throughout this

manual contain a signal word, a message and an icon.

The signal word indicates the level of the hazard in a situation.

Indicates an imminently hazardous situation which, if not avoided,

will result in death or serious injury to the operator or bystanders.

Indicates a potentially hazardous situation which, if not avoided,

could result in death or serious injury to the operator or bystanders.

Indicates a potentially hazardous situation which, if not avoided,

could result in moderate or minor injury to the operator or

bystanders.

Indicates a potentially hazardous situation which, if not avoided,

could result in damage to the equipment or vehicle or property

damage.

Safety messages in this manual contain two different type styles.

Unnumbered type states the hazard.•

Numbered type states how to avoid the hazard.•

The icon gives a graphical description of the potential hazard.

Pursuant to California Proposition 65, this product contains chemicals

known to the State of California to cause cancer and birth defects or

other reproductive harm.

• 2 •

IMPORTANT SAFETY INSTRUCTIONS1.

Riskofelectricshockorre.

Do not expose the charger to rain or snow.1.1

Use only recommended attachments. Use of an attachment not recommended 1.2

orsoldbySchumacher®ElectricCorporationmayresultinariskofre,

electric shock or injury to persons or damage to property.

To reduce the risk of damage to the electric plug or cord, pull by the plug rather 1.3

than the cord when disconnecting the charger.

An extension cord should not be used unless absolutely necessary. Use of an 1.4

improperextensioncordcouldresultinariskofreandelectricshock.Ifan

extension cord must be used, make sure:

That the pins on the plug of the extension cord are the same number, size •

and shape as those of the plug on the charger.

That the extension cord is properly wired and in good electrical condition.•

That the wire size is large enough for the AC ampere rating of the charger •

asspeciedinSection8.

To reduce the risk of electric shock, unplug the charger from the outlet before 1.5

attempting any maintenance or cleaning. Simply turning off the controls will not

reduce this risk.

Remove personal metal items such as rings, bracelets, necklaces and watches 1.6

when working with a lead-acid battery. A lead-acid battery can produce a short-

circuit current high enough to weld a ring or the like to metal, causing a severe

burn.

Donotoperatethechargerwithadamagedcordorplug;takeittoaqualied1.7

service person. (Call customer service at: 1-800-621-5485.)

Do not operate the charger if it has received a sharp blow, been dropped or 1.8

otherwisedamagedinanyway;takeittoaqualiedserviceperson.(Call

customer service at: 1-800-621-5485.)

Donotdisassemblethecharger;takeittoaqualiedservicepersonwhen1.9

serviceorrepairisrequired.Incorrectreassemblymayresultinariskofreor

electric shock. (Call customer service at: 1-800-621-5485.)

PERSONAL PRECAUTIONS2.

Risk of explosive gases.

Working in the vicinity of a lead-acid battery is dangerous. Batteries generate 2.1

explosive gases during normal battery operation. For this reason, it is of

utmost importance that you follow the instructions each time you use the

charger.

To reduce the risk of a battery explosion, follow these instructions and those 2.2

published by the battery manufacturer and the manufacturer of any equipment

you intend to use in the vicinity of the battery. Review the cautionary markings

on these products and on the engine.

• 3 •

This charger employs parts, such as switches and circuit breakers, that tend to 2.3

produce arcs and sparks. If used in a garage, locate this charger 18 inches or

moreaboveoorlevel.

NEVERsmokeorallowasparkorameinthevicinityofabatteryorengine.2.4

Be extra cautious to reduce the risk of dropping a metal tool onto the battery. 2.5

It might spark or short-circuit the battery or other electrical part that may cause

an explosion.

Use this charger for charging LEAD-ACID batteries only. It is not intended to 2.6

supply power to a low voltage electrical system other than in a starter-motor

application. Do not use this battery charger for charging dry-cell batteries that

are commonly used with home appliances. These batteries may burst and

cause injury to persons and damage to property.

NEVER charge a frozen battery.2.7

NEVER overcharge a battery.2.8

PREPARING TO CHARGE3.

Risk of contact with battery acid. Battery acid is a

highly corrosive sulfuric acid.

Consider having someone close enough by to come to your aid when you work 3.1

near a lead-acid battery.

Have plenty of fresh water and soap nearby in case battery acid contacts your 3.2

skin, clothing or eyes.

Wear complete eye and body protection, including safety goggles and 3.3

protective clothing. Avoid touching your eyes while working near the battery.

If battery acid contacts your skin or clothing, immediately wash the area with 3.4

soapandwater.Ifacidentersyoureye,immediatelyoodtheeyewithcold

running water for at least 10 minutes and get medical attention right away.

If it is necessary to remove the battery from the vehicle to charge it, always 3.5

removethegroundedterminalrst.Makesurealloftheaccessoriesinthe

vehicle are off to prevent arcing.

Be sure the area around the battery is well ventilated while the battery is being 3.6

charged.

Clean the battery terminals before charging the battery. During cleaning, keep 3.7

airborne corrosion from coming into contact with your eyes, nose and mouth.

Use baking soda and water to neutralize the battery acid and help eliminate

airborne corrosion. Do not touch your eyes, nose or mouth.

Adddistilledwatertoeachcelluntilthebatteryacidreachesthelevelspecied3.8

bythebatterymanufacturer.Donotoverll.Forabatterywithoutremovable

cell caps, such as valve regulated lead acid batteries (VRLA), carefully follow

the manufacturer’s recharging instructions.

Read, understand and follow all instructions for the charger, battery, vehicle 3.9

and any equipment used near the battery and charger. Study all of the battery

manufacturer’sspecicprecautionswhilechargingandrecommendedratesof

charge.

Determine the voltage of the battery by referring to the vehicle owner’s manual 3.10

and make sure that the output voltage selector switch is set to the correct

voltage. If the charger has an adjustable charge rate, charge the battery in the

lowestraterst.

• 4 •

Make sure that the charger cable clips make tight connections.3.11

CHARGER LOCATION4.

Risk of explosion and contact with

battery acid.

Locate the charger as far away from the battery as the DC cables permit.4.1

Never place the charger directly above the battery being charged; gases from 4.2

the battery will corrode and damage the charger.

Do not set the battery on top of the charger.4.3

Never allow battery acid to drip onto the charger when reading the electrolyte 4.4

specicgravityorllingthebattery.

Do not operate the charger in a closed-in area or restrict the ventilation in any 4.5

way.

DC CONNECTION PRECAUTIONS5.

Connect and disconnect the DC output clips only after setting all of the charger 5.1

switches to the “off” position and removing the AC plug from the electrical

outlet. Never allow the clips to touch each other.

Attach the clips to the battery and chassis, as indicated in sections 6 and 7.5.2

FOLLOW THESE STEPS WHEN BATTERY IS INSTALLED IN VEHICLE.6.

A spark near the battery may cause

a battery explosion. To reduce the

risk of a spark near the battery:

Position the AC and DC cables to reduce the risk of damage by the hood, door 6.1

and moving or hot engine parts. NOTE: If it is necessary to close the hood

during the charging process, ensure that the hood does not touch the metal

part of the battery clips or cut the insulation of the cables.

Stay clear of fan blades, belts, pulleys and other parts that can cause injury.6.2

Check the polarity of the battery posts. The POSITIVE (POS, P, +) battery post 6.3

usually has a larger diameter then the NEGATIVE (NEG, N, -) post.

Determine which post of the battery is grounded (connected) to the chassis. 6.4

If the negative post is grounded to the chassis (as in most vehicles), see step

6.5. If the positive post is grounded to the chassis, see step 6.6.

For a negative-grounded vehicle, connect the POSITIVE (RED) clip from the 6.5

battery charger to the POSITIVE (POS, P, +) ungrounded post of the battery.

Connect the NEGATIVE (BLACK) clip to the vehicle chassis or engine block

away from the battery. Do not connect the clip to the carburetor, fuel lines or

sheet-metal body parts. Connect to a heavy gauge metal part of the frame or

engine block.

• 5 •

For a positive-grounded vehicle, connect the NEGATIVE (BLACK) clip from the 6.6

battery charger to the NEGATIVE (NEG, N, -) ungrounded post of the battery.

Connect the POSITIVE (RED) clip to the vehicle chassis or engine block away

from the battery. Do not connect the clip to the carburetor, fuel lines or sheet-

metal body parts. Connect to a heavy gauge metal part of the frame or engine

block.

When disconnecting the charger, turn all switches to off, disconnect the AC 6.7

cord, remove the clip from the vehicle chassis and then remove the clip from

the battery terminal.

See CALCULATING CHARGE TIME for length of charge information.6.8

FOLLOW THESE STEPS WHEN BATTERY IS OUTSIDE VEHICLE.7.

A spark near the battery may

cause a battery explosion. To

reduce the risk of a spark near the

battery:

Check the polarity of the battery posts. The POSITIVE (POS, P, +) battery post 7.1

usually has a larger diameter than the NEGATIVE (NEG, N, -) post.

Attach at least a 24-inch (61 cm) long 6-gauge (AWG) insulated battery cable 7.2

to the NEGATIVE (NEG, N, -) battery post.

Connect the POSITIVE (RED) charger clip to the POSITIVE (POS, P, +) post 7.3

of the battery.

Position yourself and the free end of the cable you previously attached to the 7.4

NEGATIVE (NEG, N, -) battery post as far away from the battery as possible –

then connect the NEGATIVE (BLACK) charger clip to the free end of the cable.

Donotfacethebatterywhenmakingthenalconnection.7.5

When disconnecting the charger, always do so in the reverse order of the 7.6

connectingprocedureandbreaktherstconnectionwhileasfarawayfromthe

battery as practical.

A marine (boat) battery must be removed and charged on shore. To charge it 7.7

onboard requires equipment specially designed for marine use.

BATTERY CHARGING – AC CONNECTIONS8.

Riskofelectricshockorre.

This battery charger is for use on a nominal 120-volt 8.1

circuit and has a grounded plug that looks like the plug

illustrated. The charger must be grounded to reduce

the risk of electric shock. The plug must be plugged

into an outlet that is properly installed and grounded in

accordance with all local codes and ordinances. The

plugpinsmusttthereceptacle(outlet).Donotusewith

an ungrounded system.

DANGER–NeveralterACcordorplugprovided–ifitdoesnotttheoutlet,

havepropergroundedoutletinstalledbyaqualiedelectrician.Improper

connection can result in a risk of an electric shock or electrocution.

• 6 •

NOTE: Pursuant to Canadian Regulations, use of an adapter plug is not

allowed in Canada. Use of an adapter plug in the United States is not

recommended.

Recommended minimum AWG size for extension cord:8.2

100 feet long or less - use an 14 gauge extension cord.•

Over 100 feet long - use a 12 gauge extension cord.•

ASSEMBLY INSTRUCTIONS9.

No assembly required

MOUNTING INSTRUCTIONS10.

Tomountthechargertoawallorotheratsurface:

Remove the two screws from one side of the unit near the back.10.1

Attach a mounting bracket, with the keyhole towards the top, using the screws 10.2

you just removed.

Repeat for the other side. Note: Completely install one bracket before moving 10.3

to the next.

Using the charger as a template, install two #10 panhead screw anchors (or 10.4

equivalent) into the wall you want to mount the charger to. Leave the heads

of the screws extended 1/16” away from the surface. The mounting brackets

are designed to match the 16” wall stud spacing commonly found in wood and

steel framed buildings, for increased support install the anchors into the wall

studs. NOTE: Make sure the screw/anchor combination installed into the wall

isabletosupportuptoftypoundsofweight.

Position the charger, with the mounting brackets installed, so that the keyhole 10.5

slots on the mounting brackets line up with both screws you installed. Then

slide the charger down so that the screw heads lock in the keyhole slot of the

mounting brackets.

• 7 •

CONTROL PANEL11.

Illuminated ON/OFF Power Switch

Use this switch to turn the charger ON or OFF. When it is ON, it will light red.

LED Indicators

CONNECTED (red) LED - When lit, this LED indicates the battery is 1.

properly connected.

CHARGING (yellow) LED - When lit, this LED indicates the charger is 2.

charging the battery.

CHARGED (green) LED - When lit, this LED indicates the battery has 3.

reached full charge and the charger has gone into Maintain Mode.

CHECKBATTERY(red)LED-Whenashing,thisLEDindicatesthereisa4.

problem with the battery.

OPERATING INSTRUCTIONS12.

Charging

This charger is normally used when charging batteries out of a vehicle, but can

also be used to charge a battery in a vehicle.

NOTE: This charger is equipped with an auto-start feature. It will not supply

current to the battery clips until a battery is properly connected. Unlike

traditional chargers, the clips will not spark if touched together.

Check to make sure every charger component is in place and in good 1.

working condition.

Connect the battery following the precautions listed in Sections 2.

6 and 7.

Connect the battery cable to the charger.3.

Connect the AC power following the precautions listed in Section 8, if it is 4.

not already connected.

Turn the Main Power switch ON, if it is not already on.5.

Select the proper Battery Type, 6V or 12V.6.

The charger automatically starts charging and switches to Maintain Mode

when complete.

Battery Connection Indicator

If the charger does not detect a properly connected battery, the CONNECTED

(red) LED will not light until such a battery is detected. Charging will not

begin until the CONNECTED (red) LED is on. When charging begins, the

CHARGING (yellow) LED will illuminate.

Charging Mode

When an Automatic Charge is performed, the charger switches to the Maintain

Mode (see below) automatically after the battery is charged.

• 8 •

Aborted Charge

If charging can not be completed normally, charging will abort. When charging

aborts, the charger’s output is shut off, and the CHECK BATTERY (red) LED

will blink. To reset after an aborted charge, disconnect the battery.

Desulfation Mode

If the battery is left discharged for an extended period of time, it could become

sulfated and not accept a normal charge. If the charger detects a sulfated

battery, the charger will switch to a special mode of operation designed for

such batteries. If successful, normal charging will resume after the battery is

desulfated. Desulfation could take up to 10 hours. If desulfation fails, charging

will abort and the CHECK BATTERY (red) LED will blink, have the battery

checked.

Completion of Charge

Charge completion is indicated by the CHARGED (green) LED. When lit, the

charger has stopped charging and switched to the Maintain Mode of operation.

Maintain Mode

When the CHARGED (green) LED is lit, the charger has started Maintain

Mode. In this mode, the charger keeps the battery fully charged by delivering a

small current when necessary.

General Charging Notes

Fan:Thechargerisdesignedtocontrolitscoolingfanforefcientoperation.

Consequentially, it is normal for the fan to start and stop when maintaining a

fully charged battery. Keep the area near the charger clear of obstructions to

allowthefantooperateefciently.

CALCULATING CHARGE TIME13.

Use the following table to more accurately determine the time it will take to

bringabatterytofullcharge.First,identifywhereyourbatterytsintothe

chart.

Find your battery’s rating on the chart below, and note the charge time given

for each charger setting. The times given are for batteries with a 50% charge

prior to recharging. Add more time for severely discharged batteries.

BATTERY SIZE/RATING CHARGE RATE/

CHARGING TIME

6 AMP

SMALL

BATTERIES

Motorcycle,

garden

tractor, etc.

6 - 12 AH 38 min - 1¼ hrs

12 - 32 AH 1¼ - 3½ hrs

CARS/TRUCKS 200 - 315 CCA 40 - 60 RC 3¾ - 4¾ hrs

315 - 550 CCA 60 - 85 RC 4¾ - 6 hrs

550 - 1000 CCA 80 - 190

RC

6 - 11½ hrs

MARINE/DEEP CYCLE 80 RC 6 hrs

140 RC 9 hrs

160 RC 10 hrs

180 RC 11 hrs

• 9 •

MAINTENANCE INSTRUCTIONS14.

Before performing maintenance, unplug and disconnect the battery charger 14.1

(see Sections 6, 7 and 8).

After use, unplug the charger and use a dry cloth to wipe all battery corrosion 14.2

and other dirt or oil from the terminals, cords, and the charger case.

Ensure that all of the charger components are in place and in good working 14.3

condition, including the plastic boots on the battery clips.

Servicing does not require opening the unit, as there are no user-serviceable 14.4

parts.

STORAGE INSTRUCTIONS15.

Store the charger unplugged, in an upright position. The cord will still conduct 15.1

electricity until it is unplugged from the outlet.

Store inside, in a cool, dry place (unless you’re using an on-board Marine 15.2

Charger).

Do not store the clips on the handle, clipped together, on or around metal, or 15.3

clipped to cables.

TROUBLESHOOTING16.

PROBLEM POSSIBLE CAUSE REASON/SOLUTION

CONNECTED (red) LED

is not lit.

The battery is not

connected correctly.

Reverse connections at

battery.

Check for a poor connection

to the battery and frame.

Make sure the connection

points are clean. Rock the

clips back and forth for a

better connection.

Shut the charger off

and correct the lead

connections.

The CHECK BATTERY

(red) LED is blinking.

The charger is in Abort

Mode.

Reset the charger by

disconnecting the battery.

Have the battery checked.

The CHARGED (green)

LED turns on a few

minutes or less after

connecting the battery.

The battery may be

fully charged or recently

charged, leaving the battery

voltage high enough to

appear to be fully charged.

The battery may be

sulfated.

If the battery is in a vehicle,

turn the headlights on for

a few minutes to reduce

the battery voltage and try

charging again.

A sulfated battery will

eventually accept a charge.

Continue charging for a few

hours. If the charger cannot

complete charging the

battery, it will go into Abort

Mode.

The charger is making an

audible clicking sound.

The charger has a relay

that turns the current on

and off to the battery.

No problem, this is a normal

condition.

• 10 •

PROBLEM POSSIBLE CAUSE REASON/SOLUTION

Charger will not turn on

when properly connected.

AC outlet is dead.

Poor electrical connection.

Check for open fuse or

circuit breaker supplying AC

outlet.

Check power cord and

extension cord for loose

ttingplug.

Battery clips do not spark

when touched together.

The charger is equipped

with an auto-start feature.

It will not supply current

to the battery clips until

a battery is properly

connected. Unlike

traditional chargers, the

clips will not spark if

touched together.

No problem, this is a normal

condition.

REPLACEMENT PARTS17.

Output Cables (INC-406A) 38-99-000679

Output Cables (INC-406AC) 22-99-001838

BEFORE RETURNING FOR REPAIRS18.

When a charging problem arises, make certain that the battery is capable 18.1

of accepting a normal charge. Use a good battery to double check all

connections, the AC outlet for a full 120-volts, the charger clips for correct

polarity and the quality of the connections from the cables to the clips and from

the clips to the battery system. The clips must be clean.

When a battery is very cold, partially charged or sulfated, it will not draw 18.2

the full rated amperes from the charger. It is both dangerous and damaging

to a battery to force higher amperage into it than it can effectively use in

recharging.

When an UNKNOWN OPERATING PROBLEM arises, please read the 18.3

complete manual and call the customer service number for information that will

usually eliminate the need for return.

If the above solutions do not eliminate the problem or for information about troubleshooting

or replacement parts, call toll-free from anywhere in the U.S.A.

1-800-621-5485

7:00 am to 5:00 pm Central Time Monday thru Friday

• 11 •

LIMITED WARRANTY19.

SCHUMACHER ELECTRIC CORPORATION, 801 BUSINESS CENTER

DRIVE, MOUNT PROSPECT, IL 60056-2179, MAKES THIS LIMITED

WARRANTY TO THE ORIGINAL RETAIL PURCHASER OF THIS PRODUCT.

THIS LIMITED WARRANTY IS NOT TRANSFERABLE OR ASSIGNABLE.

Schumacher Electric Corporation (the “Manufacturer”) warrants this battery

charger for 1 year from the date of purchase at retail against defective material

or workmanship that may occur under normal use and care. If your unit is

not free from defective material or workmanship, Manufacturer’s obligation

under this warranty is solely to repair or replace your product with a new

or reconditioned unit at the option of the Manufacturer. It is the obligation

of the purchaser to forward the unit, along with mailing charges prepaid

to the Manufacturer or its authorized representatives in order for repair or

replacement to occur.

Manufacturer does not provide any warranty for any accessories used with this

product that are not manufactured by Schumacher Electric Corporation and

approved for use with this product. This Limited Warranty is void if the product

ismisused,subjectedtocarelesshandling,repaired,ormodiedbyanyone

other than Manufacturer or if this unit is resold through an unauthorized

retailer.

Manufacturer makes no other warranties, including, but not limited to, express,

implied or statutory warranties, including without limitation, any implied

warrantyofmerchantabilityorimpliedwarrantyoftnessforaparticular

purpose. Further, Manufacturer shall not be liable for any incidental, special

or consequential damage claims incurred by purchasers, users or others

associatedwiththisproduct,including,butnotlimitedto,lostprots,revenues,

anticipated sales, business opportunities, goodwill, business interruption

and any other injury or damage. Any and all such warranties, other than

the limited warranty included herein, are hereby expressly disclaimed and

excluded. Some states do not allow the exclusion or limitation of incidental or

consequential damages or length of implied warranty, so the above limitations

orexclusionsmaynotapplytoyou.Thiswarrantygivesyouspeciclegal

rights and it is possible you may have other rights which vary from this

warranty.

THIS LIMITED WARRANTY IS THE ONLY EXPRESS LIMITED WARRANTY

AND THE MANUFACTURER NEITHER ASSUMES OR AUTHORIZES

ANYONE TO ASSUME OR MAKE ANY OTHER OBLIGATION TOWARDS

THE PRODUCT OTHER THAN THIS WARRANTY.

Schumacher Electric Corporation Customer Service

1-800-621-5485

Monday – Friday 7:00 a.m. to 5:00 p.m. CST

Schumacher and the Schumacher Logo are registered trademarks of

Schumacher Electric Corporation

Page is loading ...

Schumacher 00-99-000940-0110 User manual

Schumacher 00-99-000940-0110 User manual

in other languages

Related papers

Other documents