13
Note :
It could happen, that during the search process, the KN-URC20B fi nds several codes to which your TV set
responds, but where all buttons do not function for each code. In this case, the search process should be
re-started (steps 3 to 9) until you obtain the best code. Re-starting the search process starts at the last saved
programming.
Automatic programming of the satellite receiver and the DVB-T (Freeview)/cable-box
(STB) according to brand
As an alternative, and if the correct code for your unit cannot be found for manual programming, you can use the
automatic search function by brand for programming.
1) Switch your satellite receiver or DVB-T (Freeview)/cable-box (STB) and TV set on.
2) Look up the brand of your unit in the brand list in the appendix to this instruction manual. There is a 3-digit
brand code for each brand.
3) Press and hold the STB Standby button (
) until the signal LED ( ) fl ashes twice.
4) Use the number buttons to enter the code 3 0 0 3. The Signal LED (
) fl ashes twice to confi rm that the
search mode has been activated.
5) Use the number keys to enter the three-digit brand code from the brand list for the brand that you have
selected. The signal LED (
) fl ashes twice to indicate that the code has been accepted.
6) Hold down the Standby button (
) on your KN-URC20B until the unit switches off. This process can take
several minutes.
7) As soon as the unit has switched off, push the OK button to confi rm the programming (
) until the Signal
LED (
) fl ashes twice.
8) Now test the individual buttons on your remote control for function, starting with the STB Standby button
(
), volume buttons (
/
), and then with the buttons 1 to 43 (in accordance with functional
description table). The AV button (
) and TV Standby button (
) are not tested.
9) If the unit responds properly to all functions, your KN-URC20B is correctly programmed and can be used.
Note
:
It could happen, that during the search process, the KN-URC20B fi nds several codes to which your unit responds,
but where all buttons do not function for each code. In this case, the search process should be re-started (steps 3
to 9) until you obtain the best code. Re-starting the search process starts at the last saved programming.
Automatic TV search
As an alternative, or if neither manual programming nor automatic programming by brand has found the correct
code for your TV set, you can use the automatic search function.
1) Switch your TV set on.
2) Press and hold the TV Standby button (
) until the signal LED ( ) fl ashes twice. If the button is not
pushed long enough, the TV set switches off. In this case, start the programming again by switching the TV set
on.
3) Use the number buttons to enter the code 1 0 0 1. The Signal LED (
) fl ashes twice to confi rm that the
search process has been activated.
4) Hold down the Standby button (
) on your KN-URC20B until the TV set switches off. This process can take
several minutes.
5) As soon as the unit has switched off, push the OK button to confi rm the programming (
) until the Signal
LED (
) fl ashes twice.
6) Test the functionality of your remote control using the TV standby button (
) and the AV button (
). If the
TV set responds properly to all functions, your KN-URC20B is correctly programmed and can be used.
Note
:
It could happen, that during the search process, the KN-URC20B fi nds several codes to which your TV set
responds, but where all buttons do not function for each code. In this case, the search process should be
re-started (steps 2 to 6) until you obtain the best code. Re-starting the search process starts at the last saved
programming.
Automatic search process on the satellite receiver and the DVB-T (Freeview)/cable-box
(STB)
As an alternative, or if neither manual programming nor automatic programming by brand has found the correct
code for your unit, you can use the automatic search function.
BA König KN-URC20B, 135x215 mm CS6.indd 13BA König KN-URC20B, 135x215 mm CS6.indd 13 12.09.2012 09:32:1512.09.2012 09:32:15