Einhell Expert Plus TE-HD 18 Li Kit User manual

TE-HD 18 Li - Solo

Art.-Nr.: 45.138.10 (1,5 Ah) I.-Nr.: 11014

Art.-Nr.: 45.138.12 (Solo) I.-Nr.: 11014

7

D Originalbetriebsanleitung

Akku-Bohrhammer

GB Original operating instructions

Cordless hammer drill

F Instructions d’origine

Marteau perforateur à

accumulateur

I Istruzioni per l’uso originali

Trapano battente a batteria

DK/ Original betjeningsvejledning

N Borehammer med oplader

S Original-bruksanvisning

Batteridriven borrhammare

NL Originele handleiding

Accu boorhamer

E Manual de instrucciones original

Taladro percutor a batería

P Manual de instruções original

Martelo perfurador sem ﬁ o

GR Πρωτότυπες Οδηγίες χρήσης

Πνευματικο πιστολετο μπαταριας

Anl_TE_HD_18_Li_Kit_SPK7.indb 1Anl_TE_HD_18_Li_Kit_SPK7.indb 1 09.05.2019 08:20:1209.05.2019 08:20:12

Page is loading ...

GB

- 17 -

Table of contents

1. Safety regulations

2. Layout and items supplied

3. Proper use

4. Technical data

5. Before starting the equipment

6. Operation

7. Cleaning, maintenance and ordering of spare parts

8. Disposal and recycling

9. Storage

10. Charger indicator

Anl_TE_HD_18_Li_Kit_SPK7.indb 17Anl_TE_HD_18_Li_Kit_SPK7.indb 17 09.05.2019 08:20:2809.05.2019 08:20:28

GB

- 18 -

Danger! - Read the operating instructions to reduce the risk of inquiry

Caution! Wear ear-muﬀ s. The impact of noise can cause damage to hearing.

Caution! Wear safety goggles. Sparks generated during working or splinters, chips and dust emitted

by the device can cause loss of sight.

Caution! Wear a breathing mask. Dust which is injurious to health can be generated when working on

wood and other materials. Never use the device to work on any materials containing asbestos!

Store the battery only in dry rooms with an ambient temperature of +10°C to +40°C. Place only charged

batteries in storage (charged at least 40%).

Select between the individual functions only when the equipment is at a standstill. If you fail to observe

this point, the equipment may be damaged.

Turn and push the SDS-Plus drill bit into the tool chuck as far as it will go. The tool will lock automatically.

1. Pull back and hold the locking sleeve!

2. Remove the tool!

Anl_TE_HD_18_Li_Kit_SPK7.indb 18Anl_TE_HD_18_Li_Kit_SPK7.indb 18 09.05.2019 08:20:2809.05.2019 08:20:28

GB

- 19 -

For use in dry rooms only.

Safety class II

2

The diameter of the drill bit must not exceed 12 mm.

Anl_TE_HD_18_Li_Kit_SPK7.indb 19Anl_TE_HD_18_Li_Kit_SPK7.indb 19 09.05.2019 08:20:2809.05.2019 08:20:28

GB

- 20 -

Danger!

When using the equipment, a few safety pre-

cautions must be observed to avoid injuries and

damage. Please read the complete operating

instructions and safety regulations with due care.

Keep this manual in a safe place, so that the in-

formation is available at all times. If you give the

equipment to any other person, hand over these

operating instructions and safety regulations as

well. We cannot accept any liability for damage

or accidents which arise due to a failure to follow

these instructions and the safety instructions.

1. Safety regulations

The corresponding safety information can be

found in the enclosed booklet.

Danger!

Read all safety regulations and instructions.

Any errors made in following the safety regula-

tions and instructions may result in an electric

shock, ﬁ re and/or serious injury.

Keep all safety regulations and instructions

in a safe place for future use.

2. Layout and items supplied

2.1 Layout (Fig. 1)

1. Locking sleeve

2. Drill/impact drill selector switch

3. Changeover switch

4. On/Oﬀ switch

5. Battery pack

6. Pushlock button

7. Battery capacity indicator

8. Charging unit

9. LED lamp

2.2 Items supplied

Please check that the article is complete as

speciﬁ ed in the scope of delivery. If parts are

missing, please contact our service center or the

sales outlet where you made your purchase at

the latest within 5 working days after purchasing

the product and upon presentation of a valid bill

of purchase. Also, refer to the warranty table in

the service information at the end of the operating

instructions.

•

Open the packaging and take out the equip-

ment with care.

•

Remove the packaging material and any

packaging and/or transportation braces (if

available).

•

Check to see if all items are supplied.

•

Inspect the equipment and accessories for

transport damage.

•

If possible, please keep the packaging until

the end of the guarantee period.

Important!

The equipment and packaging material are

not toys. Do not let children play with plastic

bags, foils or small parts. There is a danger of

swallowing or suﬀ ocating!

•

Cordless impact drill

•

Battery charger

•

Battery 1.5 Ah

•

Battery 4.0 Ah

•

Original operating instructions

•

Safety instructions

3. Proper use

The equipment is designed for drilling work with

hammer action in concrete, rock and brick, al-

ways using the correct drill bit. The equipment is

also suitable for screwdriving and drilling in wood

and steel.

The equipment is to be used only for its prescri-

bed purpose. Any other use is deemed to be a

case of misuse. The user / operator and not the

manufacturer will be liable for any damage or inju-

ries of any kind caused as a result of this.

Please note that our equipment has not been de-

signed for use in commercial, trade or industrial

applications. Our warranty will be voided if the

machine is used in commercial, trade or industrial

businesses or for equivalent purposes.

Anl_TE_HD_18_Li_Kit_SPK7.indb 20Anl_TE_HD_18_Li_Kit_SPK7.indb 20 09.05.2019 08:20:2909.05.2019 08:20:29

GB

- 21 -

4. Technical data

Voltage supply ........................................18 V d.c.

Idling speed: ......................................0-1100 rpm

Forward and reverse rotation ..........................yes

Battery charger output voltage: .............21 V d. c.

Battery charger output current: ....................... 3 A

Mains voltage for charger ...200-260 V ~ 50-60 Hz

Battery type: .......................................Lithium-ion

Number of battery cells: ............................... 5/10

Battery capacitance: .................... 1.5 Ah / 4.0 Ah

Weight.........................................................1.7 kg

The maximum screw diameter indicates the ma-

ximum diameter of the screw that can be screwed

into wood. The screw diameter can vary depen-

ding on the type of wood.

Sound and vibration

Sound and vibration values were measured in

accordance with EN 60745-1.

L

pA

sound pressure level ........................ 86 dB(A)

K

pA

uncertainty .............................................3 dB

L

WA

sound power level .......................... 97 dB(A)

K

WA

uncertainty .............................................3 dB

Wear ear-muﬀ s.

The impact of noise can cause damage to hea-

ring.

Total vibration values (vector sum of three direc-

tions) determined in accordance with

EN 60745-2-6.

Impact drilling in concrete

Vibration emission value a

h

= 9.9 m/s

2

K uncertainty = 1.5 m/s

2

The speciﬁ ed vibration value was established in

accordance with a standardized testing method. It

may change according to how the electric equip-

ment is used and may exceed the speciﬁ ed value

in exceptional circumstances.

The speciﬁ ed vibration value can be used to

compare the equipment with other electric power

tools.

The speciﬁ ed vibration value can be used for initi-

al assessment of a harmful eﬀ ect.

Keep the noise emissions and vibrations to a

minimum.

•

Only use appliances which are in perfect wor-

king order.

•

Service and clean the appliance regularly.

•

Adapt your working style to suit the appliance.

•

Do not overload the appliance.

•

Have the appliance serviced whenever ne-

cessary.

•

Switch the appliance off when it is not in use.

•

Wear protective gloves.

Caution!

Residual risks

Even if you use this electric power tool in

accordance with instructions, certain resi-

dual risks cannot be rules out. The following

hazards may arise in connection with the

equipment’s construction and layout:

1. Lung damage if no suitable protective dust

mask is used.

2. Damage to hearing if no suitable ear protec-

tion is used.

3. Health damage caused by hand-arm vib-

rations if the equipment is used over a pro-

longed period or is not properly guided and

maintained.

Limit the operating time.

All stages of the operating cycle must be conside-

red (for example, times in which the electric tools

are switched oﬀ and times in which the tool is

switched on but operates without load).

5. Before starting the equipment

Be sure to read the following information before

you use your cordless screwdriver for the ﬁ rst

time:

1. Charge the battery pack with the charger

supplied. An empty battery pack requires a

charging period of approximately 0.5-1 hour.

2. Only ever use sharp drill bits and screwdriver

bits which are suitable for the purpose and in

faultless condition.

3. Always check for concealed electric cables

and gas and water pipes when drilling and

screwing in walls.

Anl_TE_HD_18_Li_Kit_SPK7.indb 21Anl_TE_HD_18_Li_Kit_SPK7.indb 21 09.05.2019 08:20:2909.05.2019 08:20:29

GB

- 22 -

6. Operation

6.1 Charging the LI battery pack (Fig. 2-3)

1. Remove the battery pack (5) from the handle,

pressing the pushlock buttons (6) downwards

to do so.

2. Check that your mains voltage is the same as

that marked on the rating plate of the battery

charger. Insert the power plug of the charger

(8) into the mains socket outlet. The green

LED will then begin to ﬂ ash.

3. Push the battery pack onto the battery char-

ger.

In section 10 “Charger indicator” you will ﬁ nd a

table with an explanation of the LED indicator on

the charger.

If the battery pack fails to become charged, ple-

ase check

•

whether there is voltage at the socket-outlet

•

whether there is proper contact at the char-

ging contacts on the charger.

If the battery still fails to become charged, please

return

•

the charger

•

the battery pack

to our Customer Service Department.

To ensure that the LI battery pack provides

long service you should take care to recharge

it promptly. You must recharge the battery pack

when you notice that the power of the cordless

screwdriver drops.

6.2 Screw/Drill/Hammer drill selector switch

(Fig. 4/Item 2)

Caution! Change the switch position only

when the equipment is at a standstill!

Drilling/screwdriving:

For drilling/screwdriving, press the button (a) on

the selector switch (2) and simultaneously turn

the selector switch (2) to position A.

Hammer drilling:

For hammer drilling, press the button (a) on the

selector switch (2) and simultaneously turn the

selector switch (2) to position B.

Important.

You only require slight contact pressure for ham-

mer drilling. Excessive contact pressure will place

unnecessary strain on the motor. Check drill bits

at regular intervals. Sharpen or replace blunt drill

bits.

6.3 Changeover switch (Fig. 5/Item 3)

Using the slide switch above the On/Oﬀ switch

you can select the direction of rotation of the

equipment and lock the equipment so that it can-

not be switched on accidentally. You can select

between clockwise and counter-clockwise rotati-

on. To avoid causing damage to the gearing, the

direction of rotation must only be changed when

the equipment is at a standstill. When the slide

switch is in the middle position, the On/Oﬀ switch

is blocked.

Danger!

To avoid danger, the machine must only be

held using the two handles.

Otherwise you may suﬀ er an electric shock if you

drill into electric cables!

6.4 On/Oﬀ switch (Fig. 5/Item 4)

Inﬁ nitely variable speed control is possible with

the On/Oﬀ switch. The further you push the

switch, the higher the speed of the equipment.

Switching on:

Press the On/Oﬀ switch (4).

Switching oﬀ :

Press the On/Oﬀ switch (4).

6.5 Battery capacity indicator (Fig. 6 – Item 7)

Press the battery capacity indicator switch (b).

The battery capacity indicator (7) shows the char-

ge status of the battery using 3 LEDs.

All 3 LEDs are lit:

The battery is fully charged.

2 or 1 LED(s) are lit:

The battery has an adequate remaining charge.

1 LED blinks:

The battery is empty, recharge the battery.

All LEDs blink:

The battery pack has undergone exhaustive di-

scharge and is defective. Do not use or charge a

defective battery pack.

Anl_TE_HD_18_Li_Kit_SPK7.indb 22Anl_TE_HD_18_Li_Kit_SPK7.indb 22 09.05.2019 08:20:2909.05.2019 08:20:29

GB

- 23 -

6.6 LED lamp (Fig. 6 / Item 9)

The LED lamp (9) can be used in poor lighting

conditions to illuminate the area where you want

to drill or screw. The LED lamp (9) will be lit au-

tomatically as soon as you press the ON/OFF

switch (4).

6.7 Inserting a tool (Fig. 7)

Important. Set the changeover switch (3) to its

center position whenever you carry out any work

(for example changing the tool, maintenance

work, etc.) on the equipment.

•

Clean the tool before fitting it and apply a thin

coating of bit grease to the tool shaft.

•

Turn and push the dust-free tool into the tool

chuck (c) as far as it will go. The tool will lock

automatically.

•

Check that the bit is locked in placed by

pulling on it.

6.8 Removing a tool (Fig. 8)

Pull back and hold the locking sleeve (1) and re-

move the tool.

6.9 Screwdriving

We recommend using self-centering screws (e.g.

Torx screws, recessed head screws) designed for

reliable working. Be sure to use a bit that matches

the screw in shape and size. Set the torque, as

described elsewhere in these operating instruc-

tions, to suit the size of screw.

7. Cleaning, maintenance and

ordering of spare parts

Danger!

Always pull out the battery pack before

starting any cleaning work.

7.1 Cleaning

•

Keep all safety devices, air vents and the

motor housing free of dirt and dust as far as

possible. Wipe the equipment with a clean

cloth or blow it with compressed air at low

pressure.

•

We recommend that you clean the device

immediately each time you have finished

using it.

•

Clean the equipment regularly with a moist

cloth and some soft soap. Do not use

cleaning agents or solvents; these could at-

tack the plastic parts of the equipment. Ensu-

re that no water can seep into the device. The

ingress of water into an electric tool increases

the risk of an electric shock.

7.2 Maintenance

There are no parts inside the equipment which

require additional maintenance.

7.3 Ordering spare parts and accessories

Please provide the following information when

ordering spare parts:

•

Type of unit

•

Article number of the unit

•

ID number of the unit

•

Spare part number of the required spare part

For our latest prices and information please go to

www.isc-gmbh.info

Tip! For good results we

recommend high-quality ac-

cessories from !

www.kwb.eu

welcome@kwb.eu

8. Disposal and recycling

The equipment is supplied in packaging to pre-

vent it from being damaged in transit. The raw

materials in this packaging can be reused or

recycled. The equipment and its accessories are

made of various types of material, such as metal

and plastic. Never place defective equipment in

your household refuse. The equipment should

be taken to a suitable collection center for proper

disposal. If you do not know the whereabouts of

such a collection point, you should ask in your

local council oﬃ ces.

9. Storage

Store the equipment and accessories out of

children’s reach in a dark and dry place at above

freezing temperature. The ideal storage tempe-

rature is between 5 and 30 °C. Store the electric

tool in its original packaging.

Anl_TE_HD_18_Li_Kit_SPK7.indb 23Anl_TE_HD_18_Li_Kit_SPK7.indb 23 09.05.2019 08:20:2909.05.2019 08:20:29

GB

- 24 -

10. Charger indicator

Indicator status Explanations and actions

Red LED Green LED

Oﬀ Flashing Ready for use

The charger is connected to the mains and is ready for use; there is no

battery pack in the charger

On Oﬀ Charging

The charger is charging the battery pack in quick charge mode. The char-

ging times are shown directly on the charger.

Important! The actual charging times may vary slightly from the stated

charging times depending on the existing battery charge.

Oﬀ On The battery is charged and ready for use.

The unit then changes over to gentle charging mode until the battery is

fully charged.

To do this, leave the rechargeable battery on the charger for approx. 15

minutes longer.

Action:

Take the battery pack out of the charger. Disconnect the charger from the

mains supply.

Flashing Oﬀ Adapted charging

The charger is in gentle charging mode.

For safety reasons the charging is performed less quickly and takes more

time. The reasons can be:

- The rechargeable battery has not been used for a very long time.

- The battery temperature is outside the ideal range.

Action:

Wait for the charging to be completed; you can still continue to charge the

battery pack.

Flashing Flashing Fault

Charging is no longer possible. The battery pack is defective.

Action:

Never charge a defective battery pack.

Take the battery pack out of the charger.

On On Temperature fault

The battery pack is too hot (e.g. due to direct sunshine) or too cold

(below 0° C).

Action:

Remove the battery pack and keep it at room temperature (approx. 20° C)

for one day .

Anl_TE_HD_18_Li_Kit_SPK7.indb 24Anl_TE_HD_18_Li_Kit_SPK7.indb 24 09.05.2019 08:20:2909.05.2019 08:20:29

GB

- 25 -

For EU countries only

Never place any electric power tools in your household refuse.

To comply with European Directive 2012/19/EU concerning old electric and electronic equipment and

its implementation in national laws, old electric power tools have to be separated from other waste and

disposed of in an environment-friendly fashion, e.g. by taking to a recycling depot.

Recycling alternative to the return request:

As an alternative to returning the equipment to the manufacturer, the owner of the electrical equipment

must make sure that the equipment is properly disposed of if he no longer wants to keep the equipment.

The old equipment can be returned to a suitable collection point that will dispose of the equipment in

accordance with the national recycling and waste disposal regulations. This does not apply to any ac-

cessories or aids without electrical components supplied with the old equipment.

The reprinting or reproduction by any other means, in whole or in part, of documentation and papers

accompanying products is permitted only with the express consent of the iSC GmbH.

Subject to technical changes.

This consignment contains lithium-ion batteries.

In accordance with special provision 188 this consignment is not subject to the ADR regulations. Handle

with care. Danger of ignition in case of damage to the consignment package. If the consignment packa-

ge is damaged: Check and if necessary repackage.

For further information contact: 0049 9951 95920-66. Outside Germany charges will apply instead for a

regular call to a landline number in Germany.

Anl_TE_HD_18_Li_Kit_SPK7.indb 25Anl_TE_HD_18_Li_Kit_SPK7.indb 25 09.05.2019 08:20:2909.05.2019 08:20:29

GB

- 26 -

Ser vice information

We have competent service partners in all countries named on the guarantee certiﬁ cate whose contact

details can also be found on the guarantee certiﬁ cate. These partners will help you with all service re-

quests such as repairs, spare and wearing part orders or the purchase of consumables.

Please note that the following parts of this product are subject to normal or natural wear and that the

following parts are therefore also required for use as consumables.

Category Example

Wear parts* Carbon brushes, chuck, Battery

Consumables* Drill bits, chisels

Missing parts

* Not necessarily included in the scope of delivery!

In the eﬀ ect of defects or faults, please register the problem on the internet at www.isc-gmbh.info. Ple-

ase ensure that you provide a precise description of the problem and answer the following questions in

all cases:

•

Did the equipment work at all or was it defective from the beginning?

•

Did you notice anything (symptom or defect) prior to the failure?

•

What malfunction does the equipment have in your opinion (main symptom)?

Describe this malfunction.

Anl_TE_HD_18_Li_Kit_SPK7.indb 26Anl_TE_HD_18_Li_Kit_SPK7.indb 26 09.05.2019 08:20:2909.05.2019 08:20:29

GB

- 27 -

Warranty certiﬁ cate

Dear Customer,

All of our products undergo strict quality checks to ensure that they reach you in perfect condition. In the

unlikely event that your device develops a fault, please contact our service department at the address

shown on this guarantee card. You can also contact us by telephone using the service number shown.

Please note the following terms under which guarantee claims can be made:

1. These guarantee terms apply to consumers only, i.e. natural persons intending to use this product

neither for their commercial activities nor for any other self-employed activities. These warranty

terms regulate additional warranty services, which the manufacturer mentioned below promises to

buyers of its new products in addition to their statutory rights of guarantee. Your statutory guarantee

claims are not aﬀ ected by this guarantee. Our guarantee is free of charge to you.

2. The warranty services cover only defects due to material or manufacturing faults on a product which

you have bought from the manufacturer mentioned below and are limited to either the rectiﬁ cation of

said defects on the product or the replacement of the product, whichever we prefer.

Please note that our devices are not designed for use in commercial, trade or professional applica-

tions. A guarantee contract will not be created if the device has been used by commercial, trade or

industrial business or has been exposed to similar stresses during the guarantee period.

3. The following are not covered by our guarantee:

- Damage to the device caused by a failure to follow the assembly instructions or due to incorrect

installation, a failure to follow the operating instructions (for example connecting it to an incorrect

mains voltage or current type) or a failure to follow the maintenance and safety instructions or by ex-

posing the device to abnormal environmental conditions or by lack of care and maintenance.

- Damage to the device caused by abuse or incorrect use (for example overloading the device or the

use or unapproved tools or accessories), ingress of foreign bodies into the device (such as sand,

stones or dust, transport damage), the use of force or damage caused by external forces (for ex-

ample by dropping it).

- Damage to the device or parts of the device caused by normal or natural wear or tear or by normal

use of the device.

4. The guarantee is valid for a period of 24 months starting from the purchase date of the device. Gu-

arantee claims should be submitted before the end of the guarantee period within two weeks of the

defect being noticed. No guarantee claims will be accepted after the end of the guarantee period.

The original guarantee period remains applicable to the device even if repairs are carried out or

parts are replaced. In such cases, the work performed or parts ﬁ tted will not result in an extension

of the guarantee period, and no new guarantee will become active for the work performed or parts

ﬁ tted. This also applies if an on-site service is used.

5. To make a claim under the guarantee, please register the defective device at: www.isc-gmbh.info.

Please keep your bill of purchase or other proof of purchase for the new device. Devices that are

returned without proof of purchase or without a rating plate shall not be covered by the guarantee,

because appropriate identiﬁ cation will not be possible. If the defect is covered by our guarantee,

then the item in question will either be repaired immediately and returned to you or we will send you

a new replacement.

Of course, we are also happy oﬀ er a chargeable repair service for any defects which are not covered by

the scope of this guarantee or for units which are no longer covered. To take advantage of this service,

please send the device to our service address.

Also refer to the restrictions of this warranty concerning wear parts, consumables and missing parts as

set out in the service information in these operating instructions.

Anl_TE_HD_18_Li_Kit_SPK7.indb 27Anl_TE_HD_18_Li_Kit_SPK7.indb 27 09.05.2019 08:20:3009.05.2019 08:20:30

Page is loading ...

Einhell Expert Plus TE-HD 18 Li Kit User manual

This manual is also suitable for

Einhell Expert Plus TE-HD 18 Li Kit User manual

in other languages

Related papers

Other documents