Kenwood Electronics FPM260 Owner's manual

Category
Food processors
Type
Owner's manual

This manual is also suitable for

English 2 - 9
Nederlands 10 - 17
Français 18 - 26
Deutsch 27 - 34
Italiano 35 - 42
Português 43 - 50
Español 51 - 58
Dansk 59 - 66
Svenska 67 - 74
Norsk 75 - 82
Suomi 83 - 90
Türkçe 91 - 98
Česky 99 - 106
Magyar 107 - 114
Polski 115 - 123
E 124 - 132
Slovenčina 133 - 140
Українська 141 - 149
´¸∂w
051 - 751
safety
G
Read these instructions carefully and retain for future reference.
G
Remove all packaging and any labels.
G
The blades and discs are very sharp, handle with care. Always hold by
the finger grip at the top, away from the cutting edge, both
when handling and cleaning.
G
Do not lift or carry the processor by the handle - or the handle may break
resulting in injury.
G
Always remove the knife blade before pouring contents from the bowl.
G
Keep hands and utensils out of the processor bowl and liquidiser goblet
whilst connected to the power supply.
G
Switch off and unplug:
GG
before fitting or removing parts;
GG
when not in use;
GG
before cleaning.
G
Never use your fingers to push food down the feed tube. Always use the
pusher/s supplied.
G
Never fit the blade unit to the power unit without the
liquidiser or mill jar fitted.
G
Before removing the lid from the bowl or liquidiser/mill from the power unit:
GG
switch off;
GG
wait until the attachment/blades have completely stopped;
GG
be careful not to unscrew the liquidiser goblet or mill jar from the blade
assembly.
G
SCALD RISK: Hot ingredients should be allowed to cool to room
temperature before blending.
G
Do not use the lid to operate the processor, always use the on/off speed
control.
G
This appliance will be damaged and may cause injury if the
interlock mechanism is subjected to excessive force.
G
Always unplug your food processor when not in use.
G
Never use an unauthorised attachment.
G
Never leave the appliance unattended when it is operating.
G
Never use a damaged appliance. Get it checked or repaired: see ‘service
& customer care’.
G
Never let the power unit, cord or plug get wet.
G
Don’t let excess cord hang over the edge of a table or worktop or touch
hot surfaces.
G
Do not exceed the maximum capacities stated in the recommended
speed chart.
2
G
Children should be supervised to ensure that they do not play with the
appliance.
G
This appliance shall not be used by children. Keep the appliance and its
cord out of reach of children.
G
Appliances can be used by persons with reduced physical, sensory or
mental capabilities or lack of experience and knowledge if they have been
given supervision or instruction concerning use of the appliance in a safe
way and if they understand the hazards involved.
G
Only use the appliance for its intended domestic use. Kenwood will not
accept any liability if the appliance is subject to improper use, or failure to
comply with these instructions.
G
Misuse of your processor/liquidiser can result in injury.
G
The maximum rating is based on the attachment that draws the greatest
load. Other attachments may draw less power.
Refer to the relevant section under “using the attachments” for additional
safety warnings for each individual attachment.
liquidiser
G
SCALD RISK: Hot ingredients should be allowed to cool to room
temperature before blending.
G
Always take care when handling the blade assembly and avoid touching
the cutting edge of the blades when cleaning.
G
Only operate the liquidiser with the lid in place.
G
Only use the goblet with the blade assembly supplied.
G
Never run the liquidiser empty.
G
To ensure the long life of your liquidiser, do not run it for longer than 60
seconds.
G
Smoothie recipes - never blend frozen ingredients that have formed a solid
mass during freezing, break it up before adding to the goblet.
mill
G
Never fit the blade unit to your food processor without the jar fitted.
G
Never unscrew the jar while the mill is fitted to your appliance.
G
Do not touch the sharp blades – Keep the blade unit away from children.
G
Never remove the mill until the blades have completely stopped.
G
To ensure the long life of your mill, never run for longer than
30 seconds. Switch off as soon as you have got the right consistency.
G
The processing of spices is not recommended as they may damage the
plastic parts.
G
The appliance will not work if the mill is incorrectly fitted.
G
Use for dry ingredients only.
3
slicing/grating discs
G
Never remove the lid until the cutting disc has completely stopped.
G
Handle the cutting discs with care - they are extremely sharp
centrifugal juicer
G
Do not use the juicer if the filter is damaged.
G
The cutting blades on the base of the filter drum are very sharp, take care
when handling and cleaning the drum.
G
Only use the pusher supplied. Never put your fingers in the feed tube.
Unplug before unblocking the feed tube.
G
Before removing the lid, switch off and wait for the filter to stop.
4
b
efore plugging in
G
Make sure your electricity supply is the same as the one
shown on the underside of your appliance.
WARNING: THIS APPLIANCE MUST BE EARTHED.
G
This appliance conforms to EC directive 2004/108/EC on
Electromagnetic Compatibility and EC regulation no.
1935/2004 of 27/10/2004 on materials intended for contact
with food.
before using for the first time
1 Remove the plastic blade covers from the knife blade. Take
care the blades are very sharp. These covers should
be discarded as they are to protect the blade during
manufacture and transit only.
2 Wash the parts see ‘care & cleaning’
key
processor
pusher
feed tube
lid
detachable drive shaft
bowl with drive shaft
power unit
speed/pulse control
safety interlocks
cord storage (at back)
A
plastic liquidiser
blade unit
sealing ring
goblet
filler cap
lid
B
glass liquidiser
blade unit
sealing ring
goblet
lid
filler cap
attachments
Not all of the attachments listed below may be included with
your food processor. Attachments are dependent upon the
model variant.
glass multi mill (if supplied)
knife blade
dough tool
twin beater geared metal whisk
thick slicing/coarse grating disc
thin slicing/fine grating disc
rasping/parmesan disc (if supplied)
citrus juicer (if supplied)
centrifugal juicer (if supplied)
spatula (if supplied)
to use your food processor
1 Fit the bowl by aligning the on the bowl with the on
the power unit, turn clockwise until it locks .
2 Fit an attachment over the bowl drive shaft.
Note: Detachable drive shaft should only be
fitted when using the discs, citrus juicer or twin
beater geared metal whisk.
G
Always fit the bowl and attachment onto the processor
before adding ingredients.
3 Fit the lid - ensuring the top of the drive shaft/tool locates
into the centre of the lid.
G
Do not use the lid to operate the processor,
always use the on/off speed control.
4 Plug in, switch on and select a speed. (Refer to the
recommended speed chart).
G
The processor will not operate if the bowl or lid
are not fitted correctly into the interlock. Check
that the feed tube and bowl handle are situated
to the right hand side.
G
Use the pulse (P) for short bursts. The pulse will operate for
as long as the control is held in position.
5 Reverse the above procedure to remove the lid, attachments
and bowl.
G
Always switch off and unplug before removing the
lid.
important
G
Your processor is not suitable for crushing or grinding coffee
beans, or converting granulated sugar to caster sugar.
G
W
hen adding almond essence or flavouring to mixtures avoid
contact with the plastic as this may result in permanent
m
arking.
A
Plastic liquidiser
to use your liquidiser
1
Fit the sealing ring into the blade unit - ensuring the
s
eal is located correctly in the grooved area.
G
Leaking will occur if the seal is damaged or
i
ncorrectly fitted.
2
Hold the underside of the blade unit and insert the blades
into the goblet - turn anti-clockwise until it clicks . Refer to
t
he graphics on the underside of the blade unit as follows:
-
unlocked position
- locked position
The liquidiser will not operate if incorrectly
assembled.
3 Put your ingredients into the goblet.
4 Fit the lid onto the goblet and turn clockwise until it clicks.
Fit the filler cap.
5 Place the liquidiser onto the power unit, align the on the
liquidiser with the on the power unit and turn
clockwise to lock .
G
The appliance will not operate if the liquidiser is
incorrectly fitted to the interlock.
6 Select a speed (refer to the recommended speed chart) or
use the pulse control.
B
Glass liquidiser
to use your liquidiser
1 Fit the sealing ring into the blade unit - ensuring the
seal is located correctly in the grooved area.
G
Leaking will occur if the seal is damaged or
incorrectly fitted.
2 Screw the goblet onto the blade assembly . Refer to the
graphics on the underside of the blade unit as follows:
- unlocked position
- locked position
The liquidiser will not operate if incorrectly
assembled.
3 Put your ingredients into the goblet.
4 Fit the lid to the goblet and push down to secure . Fit the
filler cap.
5 Place the liquidiser onto the power unit, align the on the
liquidiser with the on the power unit and turn
clockwise to lock .
G
The appliance will not operate if the liquidiser is
incorrectly fitted to the interlock.
6 Select a speed (refer to the recommended speed chart) or
use the pulse control.
h
ints
G
When making mayonnaise, put all the ingredients, except the
o
il, into the liquidiser. Remove the filler cap. Then, with the
a
ppliance running, add the oil slowly through the hole in the
lid.
G
T
hick mixtures, e.g. pâtés and dips, may need scraping down.
I
f the mixture is difficult to process, add more liquid.
G
Ice crushing - operate the pulse in short bursts until crushed to
t
he desired consistency.
G
T
he processing of spices is not recommended as they may
damage the plastic parts.
G
T
he appliance will not work if the liquidiser is incorrectly
f
itted.
G
To blend dry ingredients - cut into pieces, remove the filler
cap, then with the appliance running, drop the pieces down
one by one. Keep your hand over the opening. For best
r
esults empty regularly.
G
Don’t use the liquidiser as a storage container. Keep it empty
before and after use.
G
Never blend more than 1.2 litres - less for frothy liquids like
milkshakes.
to use your mill (if supplied)
blade unit
sealing ring
jar
Use the mill for milling herbs, nuts and coffee beans.
1 Put the ingredients into the jar .
2 Fit the sealing ring into the blade unit .
3 Turn the blade unit upside down. Lower it into the jar, blades
down.
4 Screw the blade unit onto the jar until finger tight . Refer to
the graphics on the underside of the blade unit as follows:
- unlocked position
- locked position
5 Place the mill onto the power unit, align the on the mill
with the on the power unit and turn clockwise to lock
.
6 Switch onto maximum speed or use the pulse control.
hints
Herbs are best milled when clean and dry.
5
6
recommended speed chart
tool/attachment function speed maximum
capacities
knife blade Cake making 1 – 2 1,2Kg/2lb 6oz total weight
Rubbing fat into flour 2 300g/11oz flour weight
A
dding water to combine pastry ingredients 1 – 2
C
hopping & pureeing 2 400g/14oz chopping lean
m
eat total weight
Thick soup mixes (600ml liquid to 600g dry 1.2 litres/1 pt 16 fl oz
ingredients). Process vegetables with start on 1 and
3
00ml water until finely chopped, add increase to 2
the remaining water until incorporated.
Thinner soup mixes/milk 600 ml/18 fl oz
dough tool Yeasted mixes 2 340g/12oz flour weight
twin beater geared metal whisk Egg whites 24
C
ream 1 – 2 250 ml/7
1
2 f
l oz
discs - slicing/grating Firm food items such as carrots, hard cheeses 2–
Softer items such as cucumbers, tomatoes 1–
rasping disc (if supplied) Parmesan cheese, Potato for German 2–
potato dumplings
citrus juicer (if supplied) Citrus fruits 1–
liquidiser All processing 2 1.2 litres/1 pt 16 fl oz
glass mill (if supplied) Herbs 2 10g/
1
2oz
Nuts, coffee beans 2 50g/2oz
Uncooked meat - beef steak - cut into
2
1
2
cm cubes
2 (5 secs) 50g/2oz
centrifugal juicer (if supplied) Hard fruit and vegetables ie carrots and apples 2 800g/1lb 12oz
Soft fruit ie tomatoes and grapes 1 500g/1lb 2oz
using the attachments
Refer to recommended speed chart for each attachment.
knife blade
The knife blade is the most versatile of all the attachments.
The length of the processing time will determine the texture
achieved. For coarser textures use the pulse control.
Use the knife blade for cake and pastry making, chopping
raw and cooked meat, vegetables, nuts, pate, dips,
pureeing soups and to also make crumbs from biscuits and
bread.
hints
G
Cut food such as meat, bread, vegetables into cubes
approximately 2cm/3/4in before processing.
G
Biscuits should be broken into pieces and added down the
feed tube whilst the machine is running.
G
When making pastry use fat straight from the fridge cut into
2cm/3/4in.cubes.
G
Take care not to over-process.
dough tool
Use for yeasted dough mixes.
G
Place the dry ingredients in the bowl and add the liquid
down the feed tube whilst the machine is running. Process
until a smooth elastic ball of dough is formed this will take
60 secs.
G
Re-knead by hand only. Re-kneading in the bowl is not
recommended as it may cause the processor to become
unstable.
twin beater geared metal whisk
Use for light mixtures only eg egg whites, cream, evaporated
milk and for whisking eggs and sugar for fatless sponges.
Heavier mixtures such as fat and flour will damage it.
using the whisk
1 Fit the bowl onto the power unit, add the detachable drive
shaft.
2 Push each beater securely into the drive head.
3 Fit the whisk by carefully turning until it drops over the drive
shaft.
4 Add the ingredients.
5 Fit the lid - ensuring the end of the shaft locates into the
centre of the lid.
6 Switch on.
important
G
The whisk is not suitable for making one-stage
cakes or creaming fat and sugar as these mixes
will damage it. Always use the knife blade for
cake making.
hints
G
Best results are obtained when the eggs are at room
temperature.
G
Ensure the bowl and whisks are clean and free from grease
before whisking.
G
Carefully fold in flour and sugar by hand using a metal spoon
for fatless sponges and meringues.
slicing/grating discs
To use the discs.
reversible slicing/grating discs - thick , thin
U
se the grating side for cheese, carrots, potatoes and foods
o
f a similar texture.
Use the slicing side for cheese, carrots, potatoes, cabbage,
c
ucumber, courgette, beetroot and onions.
r
asping disc (if supplied)
Grates Parmesan cheese and potatoes for German potato
dumplings.
to use the cutting discs
1 Fit the bowl onto the power unit, add the detachable drive
shaft.
2
Holding by the centre grip, place the disc onto the drive shaft
with the appropriate side uppermost.
3 Fit the lid.
4 Put the food in the feed tube.
5 Switch on and push down evenly with the pusher - never
put your fingers in the feed tube.
hints
G
Use fresh ingredients
G
Don’t cut food too small. Fill the width of the feed tube fairly
full. This prevents the food from slipping sideways during
processing.
G
Food placed upright comes out shorter than food placed
horizontal.
G
There will always be a small amount of waste on the disc or
in the bowl after processing.
citrus juicer (if supplied)
Use the citrus juicer to squeeze the juice from citrus fruits (eg
oranges, lemons, limes and grapefruits).
cone
sieve
to use the citrus juicer
1 Fit the bowl onto the power unit, add the detachable drive
shaft.
2 Fit the sieve into the bowl - ensuring the sieve handle is
locked into position directly over the bowl handle.
3 Place the cone over the drive shaft turning until it drops all
the way down.
4 Cut the fruit in half. Then switch on and press the fruit onto
the cone.
G
The citrus juicer will not operate if the sieve is
not locked correctly.
G
For best results store and juice the fruit at room temperature
and hand roll on a worktop before juicing.
G
To help with juice extraction move the fruit from side to side
when juicing.
G
When juicing large quantities, empty the strainer regularly to
prevent the build up of pulp and seeds.
centrifugal juicer (if supplied)
Use the centrifugal juicer for making juice from firm fruit
a
nd vegetables.
p
usher
centrifugal lid
pulp remover
f
ilter drum
bowl
juicing spout
to use the centrifugal juicer
1 Place the juicer bowl with the spout onto the power unit,
a
lign the on the bowl with the on the power unit and
t
urn clockwise until it locks
.
2 Place the pulp remover into the filter drum - ensuring
the tabs locate with the slots in the bottom of the drum
.
3 Fit the filter drum .
4 Place the attachment lid onto the bowl and turn until it
locks . Your juicer will not operate if the bowl or
lid are not fitted correctly into the interlock .
5 Place a suitable glass or jug under the juice outlet.
6 Cut the food to fit the feed tube.
7 Switch on and push down evenly with the pusher - never
put your fingers in the feed tube. Process fully before
adding more.
G
After adding the last piece, let the juicer run for a further 30
seconds to extract all the juice from the filter drum.
important
G
If the juicer starts to vibrate, switch off and empty the pulp
from the drum. (The juicer vibrates if the pulp becomes
unevenly distributed).
G
Maximum capacity that can be processed at one time is
800g of fruit or vegetables.
G
Some very hard foods may make your juicer slow down or
stop. If this happens switch off and unblock the filter.
G
Switch off and clear the pulp collector regularly during use.
hints
G
Before processing remove stones and pips (eg pepper,
melon, plum) and tough skins (eg melon, pineapple). You
don’t need to peel or core apples and pears.
G
Use firm, fresh fruit and vegetables.
G
Citrus fruit - peel and remove the white pith, otherwise the
juice may taste bitter. For best results use the citrus juicer.
7
care & cleaning
G
A
lways switch off and unplug before cleaning.
G
Handle the blades and cutting disc with care -
t
hey are extremely sharp.
G
S
ome foods may discolour the plastic. This is perfectly
normal and won’t harm the plastic or affect the flavour of
y
our food. Rub with a cloth dipped in vegetable oil to
r
emove the discolouration.
p
ower unit
G
Wipe with a damp cloth, then dry. Ensure that the interlock
a
rea is clear of food debris.
G
D
on’t immerse the power unit in water.
G
Store excess cord in the storage area at the back of the
p
ower unit .
l
iquidiser/mill
1 Empty the goblet/jar before unscrewing it from the blade
unit.
2 Wash the goblet/jar by hand.
3 Remove and wash the seals.
4 Don’t touch the sharp blades – brush them clean using hot
soapy water, then rinse thoroughly under the tap. Don’t
immerse the blade unit in water.
5 Leave to dry upside down.
twin beater geared metal whisk
G
Detach the beaters from the drive head by gently pulling
them free. Wash in warm soapy water.
G
Wipe the drive head with a damp cloth, then dry.
Do not immerse the drive head in water.
all other parts
G
Wash by hand, then dry.
G
Alternatively they are dishwasher safe and can be washed
on the top rack of your dishwasher. Avoid placing items on
the bottom rack directly over the heating element. A short
low temperature (Maximum 50°C) programme is
recommended.
service & customer care
G
I
f the cord is damaged it must, for safety reasons, be
replaced by KENWOOD or an authorised KENWOOD
r
epairer.
G
I
f you experience any problems with the
o
peration of the processor, before calling for
assistance refer to the troubleshooting guide.
If you need help with:
G
u
sing your appliance or
G
servicing or repairs
G
Contact the shop where you purchased your appliance.
G
Designed and engineered by Kenwood in the UK.
G
Made in China.
IMPORTANT INFORMATION FOR CORRECT
DISPOSAL OF THE PRODUCT IN ACCORDANCE
WITH EC DIRECTIVE 2002/96/EC.
At the end of its working life, the product must not be disposed
of as urban waste.
It must be taken to a special local authority differentiated waste
collection centre or to a dealer providing this service.
Disposing of a household appliance separately avoids possible
negative consequences for the environment and health deriving
from inappropriate disposal and enables the constituent
materials to be recovered to obtain significant savings in energy
and resources. As a reminder of the need to dispose of
household appliances separately, the product is marked with a
crossed-out wheeled dustbin.
8
item suitable for
dishwashing
main bowl, lid, pusher
knife blades, dough tool
detachable drive shaft
discs
whisk beaters
Do not immerse the drive head in water
citrus juicer
centrifugal juicer
liquidiser goblet, lid, filler cap
glass mill jar
blade unit and seal for liquidiser and mill
spatula
9
troubleshooting guide
P
roblem Cause Solution
The processor will not operate. No Power. Check processor is plugged in.
Bowl not fitted to power unit correctly. Check bowl is located correctly and
the handle is situated towards the
r
ight hand side.
Bowl lid not locked on correctly. Check that the lid interlock is
l
ocated correctly into the handle
area.
T
he processor will not work
i
f the bowl and lid are fitted
i
ncorrectly.
If none of the above check the
fuse/circuit breaker in your home.
Liquidiser/mill will not operate Liquidiser/mill not locked on correctly. The liquidiser/mill will not operate if
fitted incorrectly to the interlock.
Liquidiser/mill not assembled correctly. Check blade unit is fully tightened
into the goblet/jar.
Processor stops during Processor overloaded/maximum Check maximum capacities stated
processing capacities exceeded. in the recommended speed chart.
Lid unlocked. Check lid is locked correctly.
Liquidiser/mill leaking from blade assembly base. Seal missing Check seal is fitted correctly and not
Seal incorrectly fitted damaged. To obtain a replacement
Seal damaged. seal see “service & customer care”
Poor performance of tools/attachments Refer to hints in relevant “using the attachment” section. Check attachments are
assembled correctly.
HEAD OFFICE: Kenwood Limited, 1-3 Kenwood Business Park, New Lane, Havant, Hampshire PO9 2NH
41046/4
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140
  • Page 141 141
  • Page 142 142
  • Page 143 143
  • Page 144 144
  • Page 145 145
  • Page 146 146
  • Page 147 147
  • Page 148 148
  • Page 149 149
  • Page 150 150
  • Page 151 151
  • Page 152 152
  • Page 153 153
  • Page 154 154
  • Page 155 155
  • Page 156 156
  • Page 157 157
  • Page 158 158
  • Page 159 159
  • Page 160 160
  • Page 161 161
  • Page 162 162

Kenwood Electronics FPM260 Owner's manual

Category
Food processors
Type
Owner's manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI