Magnat Audio 2.1 Owner's manual

Category
Speaker sets
Type
Owner's manual

This manual is also suitable for

9
GB
Dear MAGNAT Customer,
Congratulations on your fine new loudspeakers and thank you very much for choosing MAGNAT! You
have made an excellent choice. The high-quality speakers produced by MAGNAT are renowned all over
the world.
Please study the instructions and information below carefully before using your new loudspeakers.
IMPORTANT SAFETY PRECAUTIONSPlease read through the instruction manual carefully before
starting to use the device. This manual contains important information concerning operation
and safety aspects. It is imperative you observe all of the information. Keep the manual in a safe
location.
• WARNING NOTICES: All of the warning symbols on the speakers, accessories and in the instruction
manual itself must be adhered to.
• EXPOSURE TO HEAT: Only operate the speakers and accessories in a temperature range from
10°C to 40°C.
• The speakers should not be positioned near heat sources (heaters, ovens, radiant heaters, naked
flames, etc.). When setting up close to an amplifier a minimum distance of 10 cm must be maintained.
The distance between the active subwoofer enclosure and the walls of the room or other objects
(e. g. furniture, shelf units) may not be less than 5 cm on any side.
• The aluminium plate and cooling fins of the amplifier at the rear of the active subwoofer serve to cool
the built-in amplifier; for this reason, they must also be at least 5 cm away from all objects and must
not be covered (e.g. by a curtain).
• EFFECT OF MOISTURE: The speakers should not be exposed to dripping or splash water. Neither
should they be used to support vases or other containers filled with liquid. Do not expose the speakers
to water or high levels of humidity. There is a danger of electric shock. In the event of contact with
moisture or liquids remove the mains adapter immediately.
• FOREIGN MATERIAL: Ensure that no foreign material enters through the speaker openings and into
the interior. This could trigger short circuits and even result in electric shock and fire.
• CLEANING: Please use a soft, dry cloth with no cleaning agents, sprays or chemical solvents, as
these could damage the surfaces.
• ELECTRICAL CONNECTION: Please note the voltage levels on the information sign. The mains
adapter for the speakers should only be operated with the voltage and frequency values specified
on the sign.
• LIGHTNING PROTECTION/PREVENTIVE MEASURES: If the device is not going to be used for a
prolonged period (e.g. when on holiday), it should be disconnected from the mains by removing the
plug. The device should also be disconnected from the mains in the event of a thunderstorm. Doing
this will prevent damage caused by lightning and overvoltage.
• MAINS CABLE: The mains cable must always be suitable for operation and it should only ever be laid
out in a manner that prevents it from being trodden on. It should not be pinched by objects either, as
this can damage the cable. When using plugs and power strips it must be ensured that the cable is
not kinked at the point where it emerges from the socket. Do not connect or remove the mains cable
with damp hands.
• OVERLOAD: Sockets, power strips and extension cables should not be overloaded. If an overload
occurs, there is a risk of electric shock and fire.
• SETTING UP: Please read the installation instructions. If you want to mount the speakers on the wall,
follow the description in the installation instructions.
• The speakers should only be positioned or mounted on a solid surface and not on moving base
frames, otherwise there is a risk of injury.
• Repairs must always be conducted by qualified specialists, as you might otherwise be exposed to
dangerous high voltage levels or other hazards.
10
GB
The triangle with a lightning symbol warns the user that high voltage is used within the device
which can result in electric shock.
The triangle with an exclamation mark informs the user that important operating and
maintenance instructions (repair) are contained in the accompanying instruction manual, which
must be observed.
DO NOT OPEN! RISK OF ELECTRIC SHOCK!
CAUTION: In order to avoid electric shock do not open the speaker
housing/mains adapters or remove the covers. The user is not to conduct
any repairs him/herself. Repairs should only be conducted by qualified
technicians! Do not use any sockets or extension cables that do not fully
accommodate the plug of the device.
INSTRUCTIONS FOR DISPOSAL
In accordance with European Directive 2002/96/EC all electrical and electronic appliances must be dis-
posed of separately via local collection points. Please observe the local regulations and do not dispose
of your old appliances with normal household waste.
Battery disposal
Old batteries are hazardous waste and must be disposed of in accordance with current regulations.
CONTENTS
(A) 2 pcs. Satellite speakers
(B) 1 pc. Subwoofer with built-in amplifier
(C) 1 pc. Infrared receiver with 5 m connecting cable
(D) 1 pc. Remote control including battery (button cell CR2025))
(E) 2 pcs. Stands for satellite speakers
(F) 2 pcs. Wall bracket for satellite speakers
(G) 2 x 3 m Speaker cable for connecting the satellite speakers to the subwoofer
(H) 1 x 2 m Stereo audio cable, RCA jack on both sides
(I) 1 pc. Mains cable
(J) 1 pc. Instruction manual
UNPACKING THE SPEAKER SET
Please unpack the speakers and accessories carefully and check the contents of the box using the list
above. In the event of any transport damage, please contact your supplier. Keep the packing material in
a safe location. The original packaging enables trouble-free transportation for any subsequent relocation
and servicing requirements.
11
GB
SETTING UP THE SYSTEM COMPONENTS
Satellite speakers (A): The speakers should be positioned to the left and right of the TV. They should be
the same distance from the screen but no more than 1 m. The stands can be used to set up the satellite
speakers on a flat surface (e.g. sideboard, shelves, etc.) or they can be mounted on the wall by using
the wall bracket.“
Subwoofer (B): The subwoofer should be positioned on the floor near the satellite speakers, usually to
the left or right-hand side of the TV. The distance to the screen should not be less than 100 cm for CRT
TVs and 50 cm for flat screen TVs.
Infrared receiver (C): The receiver should be placed near the screen and/or other home cinema
equipment. It can be set up on a flat surface (e.g. sideboard, shelves, etc.) or it can be mounted on the
wall.
Please note: The remote control must be able to communicate freely with the receiver. The receiver
should also be protected from direct sunlight.
Fig. 1 shows you use of the support for the satellites.
Fig. 2 shows the use of the supplied wall mounts for the satellites.
Wall mounting of the IR receiver is illustrated in Fig.3. The mounting screws are not included in delivery.
Important information / safety instructions: The customer is solely responsible for the use of other
wall brackets / speakers attachments. The customer is also solely responsible for the secure attachment
of the speaker bracket to the wall and the selection of suitable mounting material (e.g. screws, wall plugs,
etc.), while taking account of the weight and construction of the speaker and the condition of the wall.
SYSTEM INSTALLATION
The necessary connections for the individual components are illustrated in Fig. 4.
Connecting the satellite speakers to the subwoofer:
The Interior Cinema 2.1 VA set comes with prefabricated speaker cables for the two speakers (2x3m).
If possible, use these cables when connecting the speakers. If required, you can shorten and strip the
cables yourself. Please note that both cables for the satellite speakers should be the same length. If
you need longer cables, do not extend the cables supplied, but purchase new, equivalent cables in the
desired length from a specialised store.
The connectors are located at the rear of the satellite speakers. They are equipped with a clamping
mechanism. Press the top of the terminals and insert the stripped ends of the cable into the side holes.
The speaker outputs (1) on the subwoofer are equipped with terminal screws; undo these screws one
after the other and insert the stripped ends of the cable into the side openings. Then re-tighten the ter-
minal screws. Please ensure that any protruding wires do not cause a short circuit. Make sure you pay
attention to the correct polarity.
Connecting the infrared receiver to the subwoofer:
The infrared receiver is equipped with a 5 metre long connecting cable. This cable should not be
shortened or extended. Connect the cable connector to the subwoofer via the IR sensor jack (4).
Connecting a TV to audio input LINE IN 1:
Use the supplied audio cable (H) and connect the audio output on your TV to audio input LINE IN 1 (2).
If your TV has an audio output with fixed level, this is preferable to the audio output with variable level.
Switching off the speakers on your TV: In order to achieve an optimum sound experience the integrated
speakers in your TV must be switched off. In general, this can be done as follows:
1. Via a switch on the back of the TV
2. Via the TV‘s setup menu
3. By using the remote control to set the TV volume to a minimum.
12
GB
The Interior-Cinema set can also be connected to a headphone jack on the TV. A cable adapter is
generally required for this purpose (not included in delivery). The TV‘s speakers are usually switched off
automatically when using the headphone jack. The TV volume should be set to a middle setting and the
overall listening volume should be adjusted via the Interior-Cinema remote control.
Connecting an additional audio source to LINE IN 2:
An additional audio source (e.g. MP3 player, CD player, etc.) can be connected to audio input LINE IN 2
(3) (3.5 mm stereo jack). The necessary connecting cable is not included in delivery.
Important note:
When connecting audio sources with variable output level (e.g. connection via headphone jack or a TV
set with variable audio output), the level of the audio source should be set in such a way that no distortion
can be heard at the maximum volume setting of the Magnat Interior Cinema 2.1 VA. The volume of the
audio source should also be taken into account. No distortions should be evident here either. The volume
of the audio source should also be taken into account. No distortions should be evident here either.
Mains connection:
Connect the power connector of the subwoofer (8) to an electrical socket via the mains cable (I).
OPERATION
Operating elements on the subwoofer (fig. 4):
Mains switch (6): After installation use this switch to turn on the device. If the device is not going to be
used for a prolonged period, it should be switched off.
STBY/ON button (5): This button can be used to switch between the standby and operating modes. This
function is also possible via the remote control.
Fuse (7): Only use a fuse with the parameters indicated next to the fuse holder, on the rear of the
amplifier.
The infrared receiver (fig. 5):
LED status indication (9): indicates the system‘s possible states:
•LED is illuminated red: The system is in the standby mode.
•LED is illuminated blue: The system is switched on and input LINE IN 1 is active.
•LED is illuminated purple: The system is switched on and input LINE IN 2 is active.
Sensor for the remote control (10): Please aim at this sensor when using the remote control.
Operation with the system remote control (fig. 6):
ON/STBY (11): Switches the device on when it is in the standby mode. If the LED does not illuminate,
actuate the power switch located on the rear of the subwoofer. Conversely the device can be switched
from power operation to the standby mode.
MUTE (12): Switches the sound on and off.
VOLUME (13): Increases (+) or decreases (-) the volume.
SUB (14): Increases (+) / decreases (-) the volume of the subwoofer.
SOURCE (Input selector switch) (15): Switches between the different audio sources (LINE IN 1, LINE
IN 2). The selected input is displayed via the LED (e) on the IR receiver (blue or purple).
13
GB
SERVICE AND TECHNICAL PROBLEMS
If you should encounter any technical problems, please contact your specialist dealer or
Magnat Audio-Produkte GmbH, Tel.: 02234807-0.
SPECIFICATIONS
Satellite speakers
Configuration: Two-way
Power handling capacity RMS / Max.: 50/100 watts
Impedance: 4 – 8 ohm
Frequency range: 90 – 32 000 Hz
Cross-over frequency: 5000 Hz
Efficiency (2.8 V/1 m): 88 dB
Dimensions (WxHxD): 90 x 110 x 110 mm
Weight: 0.9 kg
Subwoofer
Configuration: bass reflex, downfire
Output power RMS/Max.: 120/240 watts
Frequency range: 28 – 200 Hz
Cross-over frequency: 150 Hz
Dimensions (WxHxD): 235 x 400 x 380 mm
Weight: 9 kg
SUBJECT TO TECHNICAL CHANGE
36
Speaker R
Speaker L
TV
- +
+ -
e.g. MP3 Player
Subwoofer
4
Wir gratulieren Ihnen! Durch Ihre kluge Wahl sind Sie Besitzer eines MAGNAT HiFi-Produktes geworden. MAGNAT HiFi-Produkte
erfreuen sich aufgrund der hohen Qualität eines ausgezeichneten Rufes weltweit. Dieser hohe Qualitätsstandard ermöglicht es für MAGNAT
HiFi-Lautsprecher 5 Jahre und für MAGNAT HiFi-Elektronik 2 Jahre Garantie zu gewähren.
Die Produkte werden während des gesamten Fertigungsvorganges laufend kontrolliert und geprüft. Im Servicefall beachten Sie bitte
folgendes:
1. Die Garantiezeit beginnt mit dem Kauf des Produktes und gilt nur für den Erstbesitzer.
2. Während der Garantiezeit beseitigen wir etwaige Mängel, die nachweislich auf Material- oder Fabrikationsfehler beruhen, nach unserer
Wahl durch Austausch oder Nachbesserung der defekten Teile. Weitergehende Ansprüche, insbesondere auf Minderung, Wandlung,
Schadenersatz oder Folgeschäden sind ausgeschlossen. Die Garantiezeit wird von einer Garantieleistung durch uns nicht berührt.
3. Am Produkt dürfen keine unsachgemäßen Eingriffe vorgenommen worden sein.
4. Bei Inanspruchnahme der Garantie wenden Sie sich bitte zunächst an Ihren Fachhändler. Sollte es sich als notwendig erweisen, das
Produktanunseinzuschicken,sosorgenSiebittedafür,dass•dasProduktineinwandfreierOriginalverpackungverschicktwird,•die
Kontrollkarte ausgefüllt dem Produkt beiliegt •dieKaufquittungbeigefügtist.
5.VonderGarantieausgenommensind:•Leuchtmittel•Verschleißteile•Transportschäden,sichtbaroderunsichtbar(Reklamationenfür
solcheSchädenmüssenumgehendbeiderTransportfirma,BahnoderPosteingereichtwerden.)•KratzerinMetallteilen,Frontabdeckungen
u.s.w.(DieseDefektemüsseninnerhalbvon5TagennachKaufdirektbeiIhremHändlerreklamiertwerden.)•Fehler,diedurchfehler-
hafte Aufstellung, falschen Anschluss, unsachgemäße Bedienung (siehe Bedienungsanleitung), Beanspruchung oder äußere gewaltsame
Einwirkungentstandensind.• Unsachgemäßreparierte odergeänderte Geräte,die vonanderer Seiteals vonuns geöffnetwurden.
•FolgeschädenanfremdenGeräten•KostenerstattungbeiSchadensbehebungdurchDritteohneunservorherigesEinverständnis.
Congratulations! You have made a wise selection in becoming the owner of a MAGNAT HiFi equipment. Due to high quality
MAGNAT HiFi products have earned an excellent reputation through the western world. And this high quality standard enables us to grant
a 5-years warranty for MAGNAT HiFi speakers and a 2-years warranty for MAGNAT HiFi-electronic components.
The equipments are checked and tested continously during the entire production process. In case you have problems with your MAGNAT
HiFi equipment, kindly observe the following:
1. The guarantee period commences with the purchase of the component and is applicable only to the original owner.
2. During the guarantee period we will rectify any defects due to faulty material or workmanship by replacing or repairing the defective part
at our discretion. Further claims, and in particular those for price reduction, cancellation of sale, compensation for damages or subsequential
damages, are excluded. The guarantee period is not altered by the fact that we have carried out guarantee work.
3. Unauthorized tampering with the equipment will invalidate this guarantee.
4. Consult your authorized dealer first, if guarantee service is needed. Should it prove necessary to return the component to the factory,
pleaseinsurethat•thecomponentispackedinoriginalfactorypackingingoodcondition•thequalitycontrolcardhasbeenfilledoutand
enclosed with the component •yourencloseyourreceiptasproofofpurchase.
5.Excludedfromtheguaranteeare:•Illuminates•Wearparts•Shippingdamages,eitherreadilyapparentorconcealed(claimsforsuch
damagesmustbelodgedimmediatelywithforwardingagent,therailwayexpressofficeorpostoffice).•Scratchesincases,metalcompo-
nents,frontpanels,etc.(Youmustnotifyyourdealerdirectlyofsuchdefectswithinthreedaysofpurchase.)•Defectscausedbyincorrect
installationorconnection,byoperationerrors(seeoperatinginstructions),byoverloadingorbyexternalforce.•Equipmentswhichhave
beenrepairedincorrectlyormodifiedorwherethecasehasbeenopenedbypersonsotherthanus.•Consoquentialdamagestoother
equipments.•Reimbursementofcools,withoutourpriorconsent,whenrepairingdamagesbythirdparties.
Toutes nos félicitations!
Vouz avez bien choisi et êtes le propriétaire heureux d’un produit MAGNAT. Les produits MAGNAT ont une excellente réputation pour leur
bonne qualité. Pour cette raison, nous accordons 5 ans de garantie sur tous les MAGNAT haut-parleurs et 2 ans de garantie sur tous les
amplificateurs MAGNAT.
Les appareils sont soumis pendant toutes les opérations de fabrications à des contrôles et vérifications constants. Si, pourtant, vous ren-
contrez des difficulés avec votre appareil MAGNAT veuillez tenir compte de ce qui suit:
1. La garantie débute avec l’achat de l’appareil et est valable uniquement pour le premier propriétaire.
2. Pendant la période de garantie nous réparons les dommages provenant des défauts de matériel ou de fabrication et nous procédons, à
notre guise, à l’échange ou à la réparation des pièces défectueuses.
3. Aucune réparation impropre ne doit avoir été effectuée à l’appareil.
4. Lors d’une demande de garantie, veuillez vous adresser en premier lieu à votre distributeur. Si ce dernier décide que l’appareil doit nous
êtreretourné,veuilleztenircompteque:•l’appareilsoitexpédiédanssonermballaged’origine,•lacartedecontrôledûmentrempliesoit
jointe,•lebond’achatsoitjoint.
5.Nesontpascomprisdanslagarantie:•Matérield´eclairage•Piècesd’usure•Avariesdetransport,visiblesounon(detellesréclamations
doiventêtrefaitesimmédiatementauprèsdutransporteur,duchermindeferoudelaposte).•Desrayuressurleboîtier,piècesmétalliques,
couverclesetc.(cesdommagesdoiventêtresignalésdirectementàvotredistributeurdanslestroisjourssuivantl’achat).•Dommages
résultant d’un raccordement incorrect, maniement incorrect (voir instructions de service), surcharge ou application de force extérieure.
•Appareilsréparésnonconformémentoumodifiésetquiontétéouvertsparunepersonneautrequenous.•Dommagesultérieursà
d’autresappareils.•Remboursementdesfraisàdestiersayanteffectuélesréparationssansnotreaccordpréalable.
D
GB
F
Garantiekarte
Warranty Card
Typ/Type
Serien-Nr./Serial-No.
Name und Anschrift des Händlers/Stempel
Name and address of the dealer/stamp
Käufer/Customer
Name/Name
Straße/Street
PLZ, Ort/City
Land/Country
Nur gültig in Verbindung mit Ihrer Kaufquittung!
No warranty without receipt!
Kaufdatum/buying date
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40

Magnat Audio 2.1 Owner's manual

Category
Speaker sets
Type
Owner's manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI