Craftsman WEEDWACKER 316.711022 Owner's manual

Brand: Craftsman

Model: WEEDWACKER 316.711022

Category: Grass trimmers

Type: Owner's manual

This manual is also suitable for

Operator's Manual

2-Cycle

WEEDWACKER® GAS TRIMMER

Model No. 316.711191

CAUTION: Before using this product,

read this manuaJ and follow aJl its Safety

RuJes and Operating instructions.

* SAFETY

* ASSEMBLY

* OPERATION

* MAINTENANCE

. ESPANOL, R 19

Sears Brands Management Corporation, Hoffman Estates, IL 60179 U.S.A.

Visit our website: www.craftsman.corn

769-10237 / 00 09/14

TABLEOFCONTENTS

Safety............................................... 2

Warranty............................................. 5

KnowYourUnit........................................ 6

Specifications......................................... 6

Assembly............................................. 7

OilandFuel........................................... 9

StartingandStopping.................................. 10

Operation............................................ 11

Maintenance......................................... 13

CleaningandStorage.................................. 16

Troubleshooting....................................... 17

RepairProtectionAgreements........................... 18

ServiceNumbers.............................. BackCover

Allinformation,illustrationsandspecificationsinthismanualarebased

onthelatestproductinformationavailableatthetimeofprinting.We

reservetherighttomakechangesatanytimewithoutnotice.

©SeamBrands,LLC

Thepurposeofsafetysymbolsistoattractyourattentionto

possibledangers.Thesafetysymbols,andtheirexplanations,

deserveyourcarefulattentionandunderstanding.Thesafety

warningsdonotbythemselveseliminateanydanger.The

instructionsorwarningstheygivearenotsubstitutesforproper

accidentpreventionmeasures.

iSYMBOL MEANING

•

DANGER. Signals an EXTREME hazard.

Failure to obey a safety DANGER signal WILL result in

serious injury or death to yourself or to others.

WAR NING: Signals a SERIOUS hazard.

Failure to obey a safety WARNING signal CAN result in

serious injury to yourself or to others.

CAUTION. Signals a MODERATE hazard.

Failure to obey a safety CAUTION signal MAY result in

property damage or injury to yourself or to others.

NOTE: Advises you of information or instructions vital to the

operation or maintenance of the equipment.

SPARK ARRESTOR NOTE

NOTE: For users on U.S. Forest Land and in the states of

California, Maine, Oregon and Washington. All U.S. Forest Land

and the state of California (Public Resources Codes 4442 and

4443), Oregon and Washington require, by law that certain internal

combustion engines operated on forest brush and/or grass-covered

areas be equipped with a spark arrestor, maintained in effective

working order, or the engine be constructed, equipped and

maintained for the prevention of fire. Check with your state or local

authorities for regulations pertaining to these requirements. Failure

to follow these requirements could subject you to liability or a fine.

This unit is factory equipped with a spark arrestor, if it requires

replacement, contact a Sears Parts & Repair Service Center to

install the appropriate muffler assembly.

_ CALIFORNIA PROPOSiTiON 65

WARNING: This product contains a chemical

known to the state of California to cause cancer, birth defects

or other reproductive harm.

Read the operator's manual and follow all warnings and safety

instructions. Failure to do so can result in serious injury to the

operator and/or bystanders.

• iMPORTANT SAFETY iNSTRUCTiONS •

READ ALL iNSTRUCTiONS BEFORE OPERATING

WARNING. When using the unit, all safety

rules must be followed. Please read these instructions

before operating the unit in order to ensure the safety of

the operator and any bystanders. Please keep these

instructions for later use.

• Read the instructions carefully. Be familiar with the controls and

proper use of the unit.

Do not operate this unit when tired, ill or under the influence of

alcohol, drugs or medication.

Children must not operate the unit. Teens must be accompanied

and guided by an adult.

All guards and safety attachments must be installed properly

before operating the unit.

Inspect the unit before use. Replace damaged parts. Check for

fuel leaks. Make sure all fasteners are in place and secure.

Replace parts that are cracked, chipped, or damaged in any

way. Do not operate the unit with loose or damaged parts.

Only use the trimming line described in the Specifications section

of this manual. Never use metal-reinforced line, wire, chain or

rope. These can break off and become dangerous projectiles.

Do not replace the cutting head with rigid or metal blades. Doing

so could result in serious injury.

Be aware of risk of injury to the head, hands and feet.

Carefully inspect the area before starting the unit. Remove

rocks, broken glass, nails, wire, string and other objects that

may be thrown or become entangled with the unit.

Clear the area of children, bystanders and pets; keep them

outside a 50-foot (15 m) radius, at a minimum. Even then, they are

still at risk from thrown objects. Encourage bystanders to wear

eye protection. Ifyou are approached, stop the unit immediately.

Squeeze the throttle control and check that it returns

automatically to the idle position. Make all adjustments or

repairs before using the unit.

This unit is intended for occasional, household use only.

SAFETY WARNINGS FOR GAS UNITS

WARNING: Gasoline is highly flammable and

its vapors can explode if ignited. Take the following

precautions:

Store fuel only in containers specifically designed and approved

for the storage of such materials.

Always stop the engine and allow it to cool before filling the

tank. Never remove the fuel tank cap or add fuel when the

engine is hot. Always loosen the fuel tank cap slowly to relieve

any pressure in the tank before fueling.

Always mix and add fuel in a clean, well-ventilated outdoor area

where there are no sparks or flames. DO NOT smoke.

Never operate the unit without the fuel cap securely in place.

Avoid creating a source of ignition for spilled fuel. Wipe up any

spilled fuel from the unit immediately, before starting the unit.

Move the unit at least 30 ft. (9.1 m) from the fueling source and

site before starting the engine. DO NOT smoke.

Never start or run the unit inside a closed room or building.

Breathing exhaust fumes can kill. Operate this unit only in a well

ventilated outdoor area.

WHILE OPERATING

Wear safety glasses or goggles that meet current ANSi / ISEA

Z87.1 standards and are marked as such. Wear ear/hearing

protection when operating this unit. Wear a face mask or dust

mask if the operation is dusty.

Wear heavy long pants, boots, gloves and a long sleeve shirt. Do

not wear loose clothing, jewelry, short pants, sandals or go

barefoot. Secure hair above shoulder level.

The cutting head shield must always be in place while operating

the unit. Do not operate the unit without both trimming lines

extended and the proper line installed. Do not extend the

trimming line beyond the length of the shield.

The cutting head should remain stationary when the engine

idles. If it does not, refer to Adjusting the Idle Speed.

Adjust the handle to provide the best grip, if applicable.

Make sure the attachment is not in contact with anything before

starting the unit.

Use the unit only in daylight or good artificial light.

Avoid accidental starting. Be in the starting position whenever

pulling the starter rope. The operator and unit must be in a stable

position while starting. Refer to Starting and Stopping.

Use the right tool. Only use this tool for its intended purpose.

Always hold the unit with both hands when operating. Keep a

firm grip on both handles or grips.

Do not overreach. Always keep proper footing and balance. Take

extra care when working on stairs, steep slopes or inclines. To

avoid serious injury, do not operate the unit while on a ladder or

a roof.

Keep hands, face, and feet away from all moving parts. Do not

touch or try to stop moving parts.

Do not touch the engine, gear housing or muffler. These parts get

extremely hot from operation, even after the unit is turned off.

Do not operate the unit faster than the speed needed to do the job.

Do not run the unit at high speed when not in use.

Do not force the unit. It will do a better, safer job when used at

the intended rate.

Always stop the unit when operation is delayed or when walking

from one location to another.

Before setting the unit down, always make sure the engine is off

and all moving parts have stopped.

If you strike or become entangled with a foreign object, stop the

unit immediately and check for damage. Do not operate the unit

before repairing damage. Do not operate the unit with loose or

damaged parts.

Turn the engine to off and disconnect the spark plug for

maintenance or repair.

Use only original equipment manufacturer (OEM) replacement

parts and accessories for this unit. Use of any other parts or

accessories could lead to serious injury to the user, or damage

to the unit, and void the warranty.

Keep the unit clean. Carefully remove vegetation and other

debris that could block moving parts.

To reduce fire hazard, replace a faulty muffler and spark arrestor.

Keep the engine and muffler free from grass, leaves, excessive

grease or carbon build up.

If the unit starts to vibrate abnormally, stop the unit immediately.

Inspect the unit for the cause of the vibration. Vibration is

generally an indicator of trouble.

OTHER SAFETY WARNINGS

• Maintain the unit with care.

All service, other than the maintenance procedures described in

this manual, should be performed by a Sears or other qualified

service dealer.

Never remove, modify or make inoperative any safety device

furnished with the unit.

Before inspecting, servicing, cleaning, storing, transporting or

replacing any parts on the unit:

1.Stop the unit.

2. Make sure all moving parts have stopped.

3. Allow the unit to cool.

4. Disconnect the spark plug wire.

Secure the unit while transporting.

Never store the unit with fuel in the tank, inside a building where

fumes may reach an open flame (pilot lights, etc.) or sparks

(switches, electrical motors, etc.).

Store the unit in a dry place, secured or at a height to prevent

unauthorized use or damage. Keep the unit out of the reach of

children.

Never douse or squirt the unit with water or any other liquid.

Keep handles dry and clean (free from debris, oil and grease).

Clean the unit after each use. Refer to Cleaning and Storage. Do

not use solvents or strong detergents.

Keep these instructions. Refer to them often and use them to

instruct other users. If you loan this unit to others, also loan

them these instructions.

SAVE THESE INSTRUCTIONS

• SAFETY & iNTERNATiONAL SYMBOLS •

This operator's manual describes safety and international symbols and pictographs that may appear on this product. Read the operator's

manual for complete safety, assembly, operating and maintenance and repair information.

SYMBOL MEANING

, SAFETY ALERT SYMBOL

_ !ndicates danger I Wain!ng or cauti0n: MaY be used in

i ;ira . conjunction with other symbols or pictographs.

o READ OPERATOR'S MANUAL

WARNING: Readtheoperator's

manual(s) and follow a!! warnings and safety

instructionsl Failure to do so Can reSult in Serious

. injuryto the operator and/or bystanders.

4tii " WEAR EYE AND HEAR'NG PROTECT'ON

oWsiseAccanRcaN!Ngi :!:OuW_ _;:iteS :rid

! n;i ev i Y n] Y cJ aing :

Wear eye protection meeting Cur[ent ANSI/ISEA

Z871! standa[ds and ear protection when operating

this unit. Use afull face shield when needed.

%, UNL EDFUEL

AlwaYs use Clean, fresh unleaded fue!:

_,_,# .

.OIL

_L.5/J

. Refer to operator S manual for the proper type of Oil.

• DO NOT USE E85 FUELIN THIS UNIT

WARNIN G::"! has been ploven tha;

c_Onmtaaignieng,g[:ate rnethanndlO:f_ _thhtnwOlrWilnlti_.ke!y

SYMBOL MEANING

...... _ , ON/OFF STOP CONTROL

| oN/START/RUN

' ON/OFFSTOP CONTROL

OFF or STOP

' PRIMER BULB

Push primer bulb, fully and slowly, 10 times.

,l® ", THROWN OBJECTS AND ROTATING CUTTER CAN

/7_ CAUSE SEVERE INJURY

"" "--_'/ Sm o a be

WARNING: all bjectscn

prope ed at h gh speed, caus ng njury. Keep away

. from the rotating rotor.

' KEEP BYSTANDERS AWAY

e_Wpe_ R N !eN rgF:elK:etP,a'abY5tafelt r(1'5m)

. from the operating area.

' HOT SURFACE

WARN ! NG. Donottouchahotmuff,er

,_}t_,,,,q,, or cylinder. You may get burned. These parts get

_1_'_' extremely hot from operation. When turned off they

remain hot for a short time.

._' SHARP BLADE

,,_r_,,,,,_• Sharp blade on trimmer

attachment shield. To prevent serious injury, do not

• touch the line cutting blade.

CRAFTSMANLiMiTED WARRANTY

FOR TWO YEARS from the date of sale, this product is warranted against defects in material or workmanship.

WITH PROOF OF SALE, a defective product will receive free repair or replacement at option of seller.

ADDITIONAL LIMITED WARRANTY ON TRIMMER SHAFTS

FOR THE THIRD THROUGH TENTH YEAR from the date of sale, the outer metal housing of the upper and lower trimmer shafts is warranted

against defects in material or workmanship.

WiTH PROOF OF SALE, a new housing will be supplied free of charge. You are responsible for the labor cost of installation. This additional

coverage does not apply to inner trimmer shaft components.

For warranty coverage details to obtain free repair or replacement, visit the web page: www.craftsman.com/warranty

This warranty covers ONLY defects in material and workmanship. Warranty coverage does NOT include:

. Expendable items that can wear out from normal use within the warranty period, such as cutting line, spark plugs, or filters.

• Product damage resulting from user attempts at product modification or repair or caused by product accessories.

• Repairs necessary because of accident or failure to operate or maintain the product according to all supplied instructions.

• Preventive maintenance, or repairs necessary due to improper fuel mixture, contaminated or stale fuel.

This warranty is void if this product is ever used while providing commercial services or if rented to another person.

This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

Sears Brands Management Corporation, Hoffman Estates, IL 60179

To order parts or schedule service for this product, call 1-888-331-4569.

APPLiCATiONS

Asatrimmer:

• Cuttinggrassandlightweeds

Edging

Decorativetrimmingaroundtrees,fences,etc.

Otheroptionalaccessoriesmaybeusedwiththisunit.

Spark Plug

Muffler

Starter 1

Shaft Grip

Choke Lever

ASSEMBLY TOOLS REQUIRED:

= #2 Phillips screwdriver

• 3/8" Socket

Handle

On/Off Switch

Fuel Cap

Shaft Housing

Throttle

Control

Coupler Primer Bulb

Line Cutting Blad_

Cutting Head

Shield

Cutting Head

Engine Type ........................................................................................ Air-Cooled, 2-Cycle

Displacement ....................................................................................... 25 cc (1.52 cu. in.)

Spark Plug Gap .................................................................................... 0.025 in. (0.635 mm)

Spark Plug .......................................................................... Champion® RDJ7J or equivalent plug

Lubrication ........................................................................................... Fuel/Oil Mixture

Fuel/Oil Ratio .................................................................................................. 40:1

Fuel Tank Capacity ...................................................................................... 10 oz. (296 ml)

Approximate Unit Weight (No fuel) .................................................................... 10 - 11 Ibs. (4.5 - 5 kg)

Trimmer Mechanism ................................................................................. Hassle FreeTM Head

Trimming Line ................................................ 0.110 in. (2.79 mm) Medium Hassle FreeTM XTRA QUIET Spiral Line

Cutting Path Diameter .................................................................................. 14 in. (35.56 cm)

* All specifications are based on the latest product information available at the time of printing. We reserve the right to make changes at any

time without notice.

iNSTALLiNG THE CUTTING HEAD SHIELD

_ WARNING: To prevent serious personal injury, never ]

operate the unit without the cutting head shield in place.

1. Place the cutting head shield onto the mount bracket. Align the

holes in the cutting head shield with the holes in the mount

bracket. (Fig. 1)

Screw the 2 screws through the mount bracket and into the

cutting head shield until finger tight.

Using a #2 Phillips screwdriver, tighten the screws until the

cutting head shield is firmly in place. Tighten the screws equally.

The gap between the mount bracket and the cutting head shield

should be the same on each side.

Screws (2}

Mount Bracket " hield

Fig. 1

iNSTALLiNG AND ADJUSTING THE HANDLE

installing the Handle

1. Push the handle down onto the shaft housing (Fig. 2). The bolt

hole in the handle should be to the right.

2. Insert the bolt into the bolt hole and push it through (Fig. 2).

Tighten the bolt with a 3/8" socket, but do not tighten the bolt

completely.

3. While holding the unit in the operating position (Fig. 10), move

the handle to the location that provides the best grip. Place it a

minimum of 6 inches (15.24 cm) from the end of the shaft grip

(Fig. 2).

4. Tighten the bolt with a 3/8" socket until the handle is secure.

Adjusting the Handle

If the handle requires adjustment:

1. Loosen the bolt with a 3/8" socket (Fig. 2).

2. While holding the unit in the operating position (Fig. 10), move

the handle to the location that provides the best grip. Place it a

minimum of 6 inches (15.24 cm) from the end of the shaft grip

(Fig. 2).

3. Tighten the bolt with a 3/8" socket until the handle is secure.

Shaft Grip

Minimum 6 in.

(15.24cm}

Bolt J

Fig. 2

Handle

Shaft

Housing

WARNING: Before using any attachment, read and i

understand the manual that came with the attachment.

IFollow all safety information contained within.

WARNING: To avoid serious personal injury and i

damage to the unit, shut the unit off before removing or

installing an attachment.

OPERATING THE COUPLER

The coupler enables the use of various optional attachments.

Installing the Attachment

1. Remove the cap from the attachment. If present, remove the

gray spacer from the coupler.

2. Set the unit on a flat, level surface.

3. Turn the knob counterclockwise to loosen the coupler (Fig. 3).

4. Align the release button with the guide recess (Fig. 5).

5. Push the attachment straight into the coupler (Fig. 4) until the

release button snaps firmly into the primary hole (Fig. 5).

6. Turn the knob clockwise to tighten the coupler (Fig. 3).

CAUTION: Before operating the unit, make sure the

release button is fully snapped into the primary hole and the

knob is securely tightened.

CAUTION: Unless specified otherwise, the release

button should be snapped into the primary hole only. Using

the wrong hole could lead to personal injury or damage to

the unit.

Removing the Attachment

1. Set the unit on a flat, level surface.

2. Turn the knob counterclockwise to loosen the coupler (Fig. 3).

3. Press and hold the release button (Fig. 5).

4. Pull the attachment straight out of the coupler (Fig. 4).

Tighten

Coupler

Primary Hole

Fig. 3

Fig. 4

Loosen

Knob

Attachment

Release Button

Guide Recess

Fig. 5

OiL AND FUEL MiXiNG iNSTRUCTiONS

FUELING THE UNiT

The use of old and/or improperly mixed fuel is the most common cause

of performance problems. Use only fresh, clean unleaded gasoline.

Follow the instructions carefully for the proper gasoline/oil mixture.

Definition of Blended Fuels

Today's fuels are often a blend of gasoline and oxygenates such as

ethanol, methanol or MTBE (ether). Alcohol-blended fuel absorbs

water. As little as 1% water in the fuel can make fuel and oil

separate, forming acids when stored. ALWAYS use fresh fuel (less

than 30 days old).

NOTE: Dispose of old fuel according to federal, state and local

regulations.

Using Blended Fuels

If using a blended fuel:

• Always use the fresh fuel mix explained in your operator's manual

Use the fuel additive STA-BIL® or an equivalent

Always agitate the fuel mix before fueling the unit

Drain the tank and run the engine dry before storing the unit

_WARNING: DO NOT USE E85 FUEL iN THiS UNIT. it |

has been proven that fuel containing greater than 10%

]

ethanol will likely damage this engine and void the warranty.

Using Fuel Additives

The bottle of 2-cycle oil provided with this unit contains a fuel

additive to help inhibit corrosion and minimize gum deposits.

Always use the brand of 2-cycle oil that came with this unit. If this is

unavailable, use a 2-cycle oil designed for air-cooled engines and

mix it with a fuel additive, such as STA-BIL Fuel Stabilizer or an

equivalent. Add 0.8 oz. (23 ml) of fuel additive per gallon of fuel,

according to the instructions on the container. NEVER add fuel

additives directly to the unit's fuel tank.

WARNING: Gasoline is extremely flammable, ignited

vapors may explode. Always stop the engine and allow it

to cool before filling the fuel tank. Do not smoke while

filling the tank. Keep sparks and open flames at a distance

from the area.

WARNING: Remove the fuel cap slowly to avoid injury

from fuel spray. Never operate the unit without the fuel cap

securely in place.

WARNING: Add fuel in a clean, well ventilated outdoor

area. Wipe up any spilled fuel immediately. Avoid creating

a source of ignition for spilled fuel. Do not start the engine

until fuel vapors dissipate.

1. Position the unit with the fuel cap facing up.

2. Remove the fuel cap.

3. Place the fuel container spout into the fill hole on the fuel tank

and fill the tank.

NOTE: Do not overfill the tank.

4. Wipe up any fuel that may have spilled.

5. Reinstall the fuel cap.

6. Move the unit at least 30 ft. (9.1 m) from the fuel container and

the fueling site before starting the engine.

Mixing the Fuel

NOTE: This unit comes with a 3.2 oz. (95 ml) bottle of 2-cycle oil. To

obtain the correct fuel mixture described below, pour the entire

bottle into one gallon of unleaded gasoline.

CAUTION: For proper engine operation and maximum

reliability, pay strict attention to the gasoline and oil mixing

instructions on the 2-cycle oil bottle. Using improperly

mixed fuel can severely damage the engine.

Thoroughly mix the proper ratio of unleaded gasoline with 2-cycle

engine oil. Do not mix them directly in the unit's fuel tank. Use a

separate fuel can. Use a 40:1 gasoline/oil ratio. See the table below

for specific gasoline and oil mixing ratios.

Unleaded gasoline

1 gallon U.S.

(3.8 liters}

1 liter

2=cycle oil

3.2 fL oz.

(95ml}

25 ml

MIXING RATIO =40:1

I_ IWARNING: Operate this unit only in a well-ventilated

outdoor area. Carbon monoxide exhaust fumes can be

lethal in a confined area.

[_J WARNING: Avoid accidentally starting the unit. To avoid

serious injury, the operator and the unit must be in a stable

position when pulling the starter rope (Fig. 9).

STARTING iNSTRUCTiONS

1. Mix gasoline with oil. Refer to Oil and Fuel Mixing Instructions.

2. Fill the fuel tank. Refer to Fueling the Unit.

NOTE: There is no need to turn the unit on. The On/Off switch is in

the ON (I) position at all times (Fig. 6).

3. Slowly press and release the primer bulb 10 times (Fig. 7). If fuel

cannot be seen in the primer bulb, press and release the primer

bulb until fuel is visible.

4. Flip the choke lever clockwise until it clicks (Fig. 8).

5. Crouch in the starting position (Fig. 9).

6. DO NOT squeeze the throttle control (Fig. 6). Pull the starter

rope with a controlled and steady motion until the unit starts

(Fig. 9).

NOTE: This unit uses the INCREDI-PULL TM starting system, which

significantly reduces the effort required to start the engine.

7. Idle the engine for 5 to 10 seconds. If the unit stops during this

time, squeeze the throttle control and pull the starter rope in a

controlled and steady motion until the unit starts.

8. Squeeze and hold the throttle control. Allow the engine to warm

up for 30 to 60 seconds.

NOTE: The engine is properly warmed up when it accelerates

without hesitation.

IF... the engine does not start, begin the starting procedure with

step 3.

IF... the unit is hot and fails to start within 3 pulls of the starter rope,

squeeze the throttle control and pull the starter rope with a

controlled and steady motion until the unit starts.

Choke Lever

Fig. 6

Fig. 7

Throttle Control

Primer Bulb

STOPPING iNSTRUCTiONS

1. Release the throttle control and allow the engine to idle.

2. Press and hold the On/Off switch in the OFF (O) position until

the engine comes to a complete stop (Fig. 6).

Fig. 8

Starter Rope Grip

(

Fig. 9

Starting

Position

HOLDING THE UNiT

WARNING: Always wear eye, hearing, hand, foot and i

body protection to reduce the risk of injury when operating

this unit.

WARNING: To prevent serious personal injury, avoid arm I

contact with the engine while operating the unit. The

engine may be extremely hot.

• Stand in the operating position (Fig. 10). Stand up straight. Do

not bend over.

Keep feet apart and firmly planted.

Hold the shaft grip with the right hand. Keep the right arm

slightly bent.

Hold the handle with the left hand. Keep the left arm straight.

Hold the unit at waist level.

Position the cutting head a few inches above the ground.

Fig. lo

TiPS FOR BEST RESULTS

= To direct clippings away from the operator, tilt the cutting head

slightly down to the left; cut from right to left whenever possible.

Do not trim wet grass or weeds.

NOTE: Some line breakage will occur from:

Entanglement with foreign matter

Normal line fatigue

Attempting to cut thick vegetation

Forcing the line into objects such as walls or fence posts

DECORATIVE TRiMMiNG

When trimming around trees, posts, fences, etc., rotate the whole

unit so that the cutting head is at a 30 ° angle to the ground (Fig. 11).

Fig. 11

EDGING

The trimmer attachment can be used for edging (Fig. 12).

Alternatively, bladed lawn edger attachments can also be purchased

for use with this unit.

Rotating the Trimmer Attachment

_ WARNING: To avoid serious personal injury and I

damage to the unit, shut the unit off before rotating the

attachment.

When edging around sidewalks, flowerbeds, etc., rotate the trimmer

attachment 90° inside the coupler. DO NOT rotate the entire unit 90°.

1. Turn the knob counterclockwise to loosen the coupler (Fig. 3).

Refer to Operating the Coupler in the Assembly section.

2. Press and hold the release button (Fig. 5).

3. Rotate the attachment until the release button snaps firmly into

the 90° edging hole (Fig. 13).

4. Turn the knob clockwise to tighten the coupler (Fig. 3).

CAUTION: Only snap the release button into the 90°

edging hole when edging with the trimmer attachment.

Using the 90 ° edging hole with other attachments could

lead to personal injury or damage to the unit.

Maintaining the Trimming Line

Hard surfaces, such as sidewalks, can cause the trimming line to

wear down quickly or break.

• Frequently check the trimming line length. Replace the trimming

line as needed. Refer to Replacing the Trimming Line.

DO NOT force the unit. Make shallow cuts in as many passes as are

necessary to achieve the desired depth. Cut at a slow, even pace.

Fig. 12

Release

Hole

Fig. 13

WARNING: To prevent serious injury, never perform

maintenance or repairs while the unit is running. Always

allow the unit to cool before servicing or repairing the unit.

Disconnect the spark plug wire to prevent the unit from

starting accidentally.

MAINTENANCE SCHEDULE

Perform these required maintenance procedures at the frequency

stated in the table. These procedures should also be a part of any

seasonal tune-up.

NOTE: Some maintenance procedures may require special tools or

skills. If unsure about these procedures, take the unit to a Sears

or other qualified service dealer. Call 1-888-331-4569 for more

information.

NOTE: Maintenance, replacement, or repair of the emission control

devices and system may be performed by a Sears or other qualified

service dealer. Call 1-888-331-4569 for more information.

NOTE: Please read the California/EPA statement that came with the

unit for a complete listing of terms and coverage for the

emissions control devices, such as the spark arrestor, muffler,

carburetor, etc.

FREQUENCY MAINTENANCE REQUIRED

Every 10 hours Clean and re-oil the air filter. Refer to

Maintaining the Air Filter.

Every 25 hours Check the spark plug condition and gap. Refer

to Maintaining the Spark Plug.

Holes

Fig. 14

Line

Cutting Head

REPLACING THE TRiMMiNG LiNE

Only use the trimming line described in the Specifications section.

Other types of trimming line may cause the unit to overheat or fail.

I_ IWARNING: Never use metal-reinforced line, wire, chain or |

rope. These can break off and become dangerous projectiles.

1. Remove the old line from the cutting head. Push one end of the

trimming line into the cutting head until a loop of line protrudes

from the head. Pull the loop to remove the line.

2. Use a clean cloth to clean the surface of the cutting head.

3. Insert the ends of the new trimming line into the holes in the

cutting head (Fig. 14). Push the line through the holes until both

ends protrude from the positioning tunnels (Fig. 15).

4. Pull the ends of the line until the line is tight against the cutting

head. Make sure the ends of the line are of equal length (Fig. 16).

If one end is longer than the other, push the longer end back

through the cutting head partway and pull the shorter end out. If

necessary, repeat this process until both ends are of equal length.

5. Press the exposed loop of trimming line until it is tight against

the cutting head (Fig. 16).

Positioning

Tunnel

Line

Fig. 15

Loop

Line

Fig. 16

MAiNTAiNiNG THE AiR FILTER

_ WARNING: To avoid serious personal injury, always stop

the engine and allow it to cool before cleaning or maintaining

the unit.

Failure to maintain the air filter can result in poor performance or

can cause permanent damage to the engine. Engine failure due to

improper air filter maintenance is not covered by the product warranty.

Cleaning the Air Filter

1. Open the air filter cover: press in the lock tab and swing the air

filter cover to the right (Fig. 17).

2. Remove the air filter from inside the air filter cover (Fig. 17).

3. Wash the air filter in detergent and water. Rinse the air filter

thoroughly and allow it to dry.

4. Lightly coat the air filter with clean SAE 30 oil.

5. Squeeze the air filter to spread and remove excess oil.

6. Reinstall the air filter inside the air filter cover (Fig. 17).

NOTE: Operating the unit without the air filter and air filter cover will

VOID the warranty.

7. Close the air filter cover: swing the air filter cover to the left and

press it closed until the lock tab snaps into place (Fig. 17).

Air Filter

i!!!il "2, ',,

Lock Tab Air Filter Cover

Fig. 17

ADJUSTING THE iDLE SPEED

_ ARNING: The cutting head may spin during idle speed_

adjustments. Wear protective clothing and observe all

Jsafety instructions to prevent serious personal injury.

If the engine will not idle properly:

1. Drain the fuel tank and add fresh, properly-mixed fuel. Refer to

Oil and Fuel.

2. Clean the air filter. Refer to Maintaining the Air Filter.

If the engine still will not idle properly, adjust the idle speed:

1. Start the engine. Refer to Starting and Stopping.

2. Release the throttle control and let the engine idle.

• If the engine stops, increase the idle speed. Use a small

Phillips screwdriver to turn the idle speed screw clockwise,

1/8 of a turn at a time, until the engine idles smoothly (Fig. 18).

If the cutting head spins when the engine idles, reduce the idle

speed. Turn the idle speed screw counterclockwise, 1/8 of a

turn at a time, until the cutting head stops moving (Fig. 18).

If the engine still will not idle properly, and any of the following

conditions are true, take the unit to a Sears or other qualified service

dealer:

the engine hesitates or stalls on acceleration

there is a loss of engine power

idle Speed Screw

Fig. 18

MAiNTAiNiNG THE SPARK PLUG

1. Stop the engine and allow it to cool. Grasp the spark plug boot

firmly and pull it from the spark plug.

2. Clean around the spark plug. Remove the spark plug from the

cylinder head with a 5/8-inch socket, turning counterclockwise.

I _ib !WARNING: Do not sand blast, scrape or clean spark plug I

electrodes. Grit in the engine could damage the cylinder.

3. Inspect the spark plug. If the spark plug is cracked, fouled or

dirty, replace it with replacement part #753-06193, a Champion

RDJ7J or an equivalent spark plug.

4. Use a feeler gauge to set the air gap at 0.025 in. (0.635 ram}

(Fig. 19).

5. Install the spark plug in the cylinder head. Tighten the spark plug

with a 5/8-inch socket, turning it clockwise until snug.

NOTE: If using a torque wrench, torque to:

110=120 in.olb. (12.3=13.5 Nora). Do not over tighten.

6. Reattach the spark plug boot.

0.025 in.

(0.635 rnrn}

Fig. 19

CLEANING STORAGE

_ WARNING" To avoid serious personal injury, always stop

the engine and allow it to cool before cleaning or maintaining

the unit.

Use a small brush to clean the outside of the unit. Do not use strong

detergents. Household cleaners that contain aromatic oils such as

pine and lemon, and solvents such as kerosene, can damage

plastic. Wipe off any moisture with asoft cloth.

• Never store a fueled unit where fumes may reach an open flame

or spark.

Allow the engine to cool before storing.

Lock up the unit to prevent unauthorized use or damage.

Store the unit in a dry, well-ventilated area.

Store the unit out of the reach of children.

Short-term Storage (1-2 weeks)

1. Store the unit in a horizontal position. If this is not possible, store

the unit vertically with the engine at the top.

Long-term Storage

1. Remove the fuel cap, tip the unit and drain the fuel into an

approved container. Reinstall the fuel cap.

2. Start the engine and allow it to run until it stalls. This ensures

that all fuel has been drained from the carburetor.

3. Allow the engine to cool. Remove the spark plug and put 5

drops of any high-quality motor oil or 2-cycle oil into the

cylinder. Pull the starter rope slowly to distribute the oil. Reinstall

the spark plug.

4. Thoroughly clean the unit and inspect it for any loose or

damaged parts. Repair or replace damaged parts and tighten

loose screws, nuts or bolts.

Preparing the Unit for Use after Long-term Storage

1. Remove the spark plug and drain all of the oil from the cylinder.

NOTE: Do not use fuel that has been stored for more than 30 days.

Dispose of old fuel according to federal, state and local regulations.

PROBLEM

The fuel tank is empty

The engine is flooded

The spark plug is fouled

SOLUTION

Fill the fuel tank with properly mixed fuel

iii [ [ """""""""""""""'"""""""""""""""""""""'"'

Squeeze the throttle control and pull the starter rope until the engine

starts

Replace the spark plug

The air filter is dirty

The idle speed is incorrect

The fuel is old (over 30 days) and/or improperly mixed

The air filter is dirty

The fuel is old (over 30 days) and/or improperly mixed

The spark plug is fouled

Clean or replace the air filter

Adjust the idle speed

Drain the fuel tank and add fresh, properly-mixed fuel

Clean or replace the air filter

Drain the fuel tank and add fresh, properly-mixed fuel

Replace the spark plug

° Find information and tools to help with home projects.

brought to you by Sears

Congratulations on making a smart purchase. Your new Craftsman@ product is designed and manufactured for years of dependable

operation. But like all products, it may require repair from time to time. That's when having a Repair Protection Agreement can save you

money and aggravation.

Here's what the Repair Protection Agreement* includes:

[] Expert service by our 10,000 professional repair specialists

[] Unlimited service and no charge for parts and labor on all covered repairs

[] Product replacement up to $1500 if your covered product can't be fixed

[] Discount of 25% from regular price of service and related installed parts not covered by the agreement; also, 25% off regular price of

preventive maintenance check

[] Fast help by phone - we call it Rapid Resolution - phone support from a Sears representative. Think of us as a "talking owner's manual."

Once you purchase the Repair Protection Agreement, a simple phone call is all that it takes for you to schedule service. You can call anytime

day or night, or schedule a service appointment online.

The Repair Protection Agreement is a risk-free purchase. If you cancel for any reason during the product warranty period, we will provide a

full refund. Or, a prorated refund anytime after the product warranty period expires. Purchase your Repair Protection Agreement today!

Some limitations and exclusions appJy. For prices and additional information in the U.S.A. call 1-800-827-6655.

*Coverage in Canada varies on some items. For full details call Sears Canada at 1-800-361-6665.

Sears installation Service

For Sears professional instaflation of home appliances, garage door openers, water heaters, and other major home items, in the U.S.A. or

Canada call 1-800-4-MY-HOME.

Manual del Operador

Motor de 2 tiernpos

RECORTADOR WEEDWACKER_ A GASOLINA

Modelo No. 316.711191

PRECAUCION: Antes de utilizar, este

producto lea este manual y siga todas

las reglas de seguridad e instrucciones

de operaci6n.

* SEGURIDAD

* ENSAMBLAJE

. OPERACION

* MANTENIMIENTO

Sears Brands Management Corporation, Hoffman Estates, iL 60179 U.S.A.

Visite nuestro sitio web: www.craftsman.com

769-10237 / 00 09/14

Page is loading ...

Product questions or problems?

Customer Care ot Line

Get answers to questions, troubleshoot problems,

order parts, or schedule repair service.

Para respuestas a preguntas o problemas, y ordenar

piezas o pedir servicio para la reparaci6n de su equipo.

To help us help you, register your product at www.craftsman.com/registration

Para poderte ayudar mejor, registra tu producto en www.craftsman.com/registration

Join the Craftsman Club todayZ

CRRFT :MRN

www.craftsman.com/signup

Receive exclusive member benefits including special pricing and offers,

project sharing, expert advice, and SHOP YOUR WAY REWARDS!

Como miembro exclusivo, recibe diversos beneficios como ofertas, precios especiales, proyectos

nuevos, consejos de expertos y nuestro programa de puntos SHOP YOUR WAY REWARDS!

® Registered Trademark /TM Trademark of KCD IP, LLC in the United States, or Sears Brands, LLC in other countries

® Marca Registrada/TM Marca de FAbrica de KCD IP, LLC en Estados Unidos, o Sears Brands, LLC in otros paises

Craftsman WEEDWACKER 316.711022 Owner's manual

Brand: Craftsman

Model: WEEDWACKER 316.711022

Category: Grass trimmers

Type: Owner's manual

This manual is also suitable for

Download PDF

report

in other languages

español: Craftsman WEEDWACKER 316.711022 El manual del propietario

Craftsman WEEDWACKER 316.711022 Owner's manual

This manual is also suitable for

Craftsman WEEDWACKER 316.711022 Owner's manual

in other languages

Related papers