Apevia X-Gear ATXB5KLW Series Installation guide

Apevia
Brand
Apevia
Model
X-Gear ATXB5KLW Series
Category
Computer cases
Type
Installation guide
ATXB5KLW(X-Gear) Series Installation Guide
1:Unscrew the thumb screws 2.Pull the side panel back then 3:Find the motherboard stand-offs
from side panel. pull out. from the enclosed screw box.
4:Put the motherboard stand-offs 5.Sit the motherboard on the 6.Find screws in the screw box.
on the motherboard tray. motherboard tray.
7.Screw in all the screws into the 8.Same as Step 7.
motherboard stand-offs
9.Take out front panel:
Step (1): Unscrew the side panel Step (2): Take out the side Step (3): There are 4 screws that
panel (motherboard side) panel (motherboard side) hold the front panel to the case. (2
on each side) Unscrew the 2 screws
from inside of the case.
Step (4): Unscrew the other Step (5): Pull out the front panel
2 screws from the other side. from the bottom.
10.Optional:Install case fan in 11.Optional: Install case fan 12.Take out the metal plate and
the front panel (You can put up at rear (1*80mm-120mm fan) install 5.25” drives(DVD, CD-RW,
to 2*80mm fans in the front.) CD-ROM)
13.Secure the 5.25” drives 14.Slide in 3.5” floppy drive and 15.Install 3.5” hidden drives such
in place with screws. secure with screws. as hard drive, zip drive.
16.Screw all 3.5” hidden drives 17.Snap in the front panel and 18.Audio Cable: Take out the I/O slot
with screws. screw the front panel to the case. with a hole from the back of the case
.
19.Find the audio cables and 20.Put the I/O slot back. 21.Screw the I/O slot back and
bring them through the I/O slot leave the audio connectors outside
to outside of the back panel. the case for now.
22.Find the 4pin connectors 23.Find the 20-pin connector 24.Plug into your motherboard.
(Female and Male) from case from power supply. Different M/B has different layout.
fan. Connect the Male to the Please refer to your motherboard
female 4pin from power supply. user manual.
25.Find the 4-pin P4 connector 26.Plug into your motherboard. 27.Find 2*USB cables.
from power supply.(for P4 only) (For Intel P4 motherboard only) (USB1 & USB2)
28.Plug USB cables to your M/B. 29.Find “HDD LED” and 30.Plug them onto your M/B.
Please refer to M/B user manual. “Reset SW” cables. Please refer to M/B user manual.
31.Find “Power SW” and “+P LED” 32.Plug audio cables to 33.Find “Case Speaker” from
“-P LED” cables and plug onto M/B. sound card or M/B. screw box.
Please refer to M/B user manual.
34.Install case speaker to M/B 35.Install LED Lights: Find 2*LED 36.Connect the 4-pin Male connector
following M/B user manual. connectors from the front panel. to a 4-pin Female connector from
They are 2*2-pin connectors that power supply.
lead out to2*4-pin connector
(1*Male, 1*Female)
37.Once power on, the front 38.Find “Case Feet” in screw box. Lay
4 LEDs will light up. case down and put “Case Feet” on.
Note: You can link together all the 4-pin connectors(male to female) from all the case fans, LED, HDD and just
use one of the 4-pin Molex connectors from power supply. It will leave you more 4-pin connectors from your
power supply for other devices.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5

Apevia X-Gear ATXB5KLW Series Installation guide

Apevia
Brand
Apevia
Model
X-Gear ATXB5KLW Series
Category
Computer cases
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents