Toro Mid-Size ProLine Pistol Grip Hydro, 15 HP User manual

Brand: Toro

Model: Mid-Size ProLine Pistol Grip Hydro, 15 HP

Category: Lawnmowers

Type: User manual

Operator’s Manual

Original Instructions (EN)

Form No. 3352–529

Mid-Size Mower

ProLine Hydro 15 hp with 48in Side Discharge

Mower

Model No. 30528—Serial No. 250000001 and Up

W 2004 by The Toro Company

8111 Lyndale Avenue South

Bloomington, MN 55420-1196

Printed in the USA

CALIFORNIA

Proposition 65 Warning

The engine exhaust from this product contains

chemicals known to the State of California to cause

cancer, birth defects, or other reproductive harm.

Warning

Important This engine is not equipped with a spark

arrester muffler. It is a violation of California Public

Resource Code Section 4442 to use or operate this engine

on any forest-covered, brush-covered or grass-covered

land. Other states or federal areas may have similar laws.

This spark ignition system complies with Canadian

ICES-002.

Ce système d’allumage par étincelle de véhicule est

conforme à la norme NMB-002 du Canada.

The enclosed Engine Owner’s Manual is supplied for

information regarding The U.S. Environmental

Protection Agency (EPA) and the California Emission

Control Regulation of emission systems, maintenance

and warranty.

Keep this engine Owner’s Manual with your mower.

Should this engine Owner’s Manual become damaged

or illegible, replace immediately. Replacements may be

ordered through the engine manufacturer.

Contents

Page

Introduction 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Safety 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Safe Operating Practices 3. . . . . . . . . . . . . . . . . . . .

Toro Mower Safety 4. . . . . . . . . . . . . . . . . . . . . . . .

Slope Chart 7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Safety and Instruction Decals 9. . . . . . . . . . . . . . . .

Gasoline and Oil 12. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Recommended Gasoline 12. . . . . . . . . . . . . . . . . . . .

Using Fuel Stabilizer/Conditioner 12. . . . . . . . . . . .

Filling the Fuel Tank 12. . . . . . . . . . . . . . . . . . . . . .

Checking the Engine Oil Level 12. . . . . . . . . . . . . .

Setup 13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Loose Parts 13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Installing the Front Casters 14. . . . . . . . . . . . . . . . . .

Installing the Upper Handle 14. . . . . . . . . . . . . . . . .

Connecting the Throttle Cable 15. . . . . . . . . . . . . . .

Installing the Blade Control (PTO) Rod 15. . . . . . . .

Installing the Control Rods 15. . . . . . . . . . . . . . . . . .

Installing the Control Arm Rods 16. . . . . . . . . . . . .

Page

Installing the Speed Control Rod 16. . . . . . . . . . . . .

Installing the Fuel Tank 17. . . . . . . . . . . . . . . . . . . .

Setting up the Hydro Linkage 17. . . . . . . . . . . . . . .

Checking the Hydraulic Fluid 18. . . . . . . . . . . . . . .

Operation 19. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Think Safety First 19. . . . . . . . . . . . . . . . . . . . . . . . .

Controls 19. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Operating the Parking Brake 19. . . . . . . . . . . . . . . .

Starting and Stopping the Engine 20. . . . . . . . . . . . .

Operating the Neutral Locks 21. . . . . . . . . . . . . . . .

Operating the Mower Blade Control (PTO) 21. . . . .

The Safety Interlock System 22. . . . . . . . . . . . . . . .

Driving the Machine Forward or Backward 22. . . . .

Bringing the Machine to Neutral Position 23. . . . . .

Stopping the Machine 23. . . . . . . . . . . . . . . . . . . . . .

Pushing the Machine by Hand 23. . . . . . . . . . . . . . .

Transporting Machines 24. . . . . . . . . . . . . . . . . . . . .

Using the Side Discharge or Mulching Grass 24. . . .

Adjusting the Height-of-Cut 24. . . . . . . . . . . . . . . . .

Adjusting the Caster Position 25. . . . . . . . . . . . . . . .

Height-of-Cut Chart 26. . . . . . . . . . . . . . . . . . . . . . .

Maintenance 27. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Recommended Maintenance Schedule 27. . . . . . . . .

Servicing the Cutting Blades 28. . . . . . . . . . . . . . . .

Servicing the Air Cleaner 30. . . . . . . . . . . . . . . . . . .

Servicing the Engine Oil 31. . . . . . . . . . . . . . . . . . .

Servicing the Spark Plug 32. . . . . . . . . . . . . . . . . . .

Servicing the Brake 33. . . . . . . . . . . . . . . . . . . . . . .

Checking the Tire Pressure 34. . . . . . . . . . . . . . . . . .

Cleaning the Cooling System 34. . . . . . . . . . . . . . . .

Greasing and Lubricating the Machine 34. . . . . . . .

Cleaning the Cooling System 35. . . . . . . . . . . . . . . .

Draining the Fuel Tank 35. . . . . . . . . . . . . . . . . . . . .

Servicing the Fuel Filter 35. . . . . . . . . . . . . . . . . . . .

Servicing the Hydraulic System 36. . . . . . . . . . . . . .

Performing the Hydro Linkage Adjustments 37. . . .

Adjusting the Speed Control Linkage 37. . . . . . . . .

Adjusting the Neutral Control Linkages 38. . . . . . . .

Adjusting the Hydro Control Linkages 39. . . . . . . .

Adjusting the Control Rod 41. . . . . . . . . . . . . . . . . .

Tracking the Adjustment 41. . . . . . . . . . . . . . . . . . .

Adjusting the Spring Anchor Links 41. . . . . . . . . . .

Checking the Belts 42. . . . . . . . . . . . . . . . . . . . . . . .

Replacing the Mower Belt 42. . . . . . . . . . . . . . . . . .

Adjusting the Mower Belt Tension 43. . . . . . . . . . . .

Adjusting the Blade Brake 43. . . . . . . . . . . . . . . . . .

Replacing the Grass Deflector 44. . . . . . . . . . . . . . .

Wiring Diagram 44. . . . . . . . . . . . . . . . . . . . . . . . . .

Hydraulic Diagram 45. . . . . . . . . . . . . . . . . . . . . . . .

Page

Cleaning and Storage 46. . . . . . . . . . . . . . . . . . . . . .

Troubleshooting 47. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

The Toro Total Coverage Guarantee 52. . . . . . . . . . . . .

Introduction

Read this manual carefully to learn how to operate and

maintain your product properly. The information in this

manual can help you and others avoid injury and product

damage. Although Toro designs and produces safe

products, you are responsible for operating the product

properly and safely.

Whenever you need service, genuine Toro parts, or

additional information, contact an Authorized Service

Dealer or Toro Customer Service and have the model and

serial numbers of your product ready. Figure 1 illustrates

the location of the model and serial numbers on the

product.

Figure 1

1. Location of the model and serial numbers

Write the product model and serial numbers in the space

below:

Model No.

Serial No.

This manual identifies potential hazards and has special

safety messages that help you and others avoid personal

injury and even death. Danger, Warning, and Caution are

signal words used to identify the level of hazard. However,

regardless of the hazard, be extremely careful.

Danger signals an extreme hazard that will cause serious

injury or death if you do not follow the recommended

precautions.

Warning signals a hazard that may cause serious injury or

death if you do not follow the recommended precautions.

Caution signals a hazard that may cause minor or moderate

injury if you do not follow the recommended precautions.

This manual uses two other words to highlight information.

Important calls attention to special mechanical

information and Note: emphasizes general information

worthy of special attention.

Safety

This machine meets or exceeds the B71.4–2004

specifications of the American National Standards

Institute in effect at the time of production.

Note: The addition of attachments made by other

manufacturers that do not meet American National

Standards Institute certification will cause noncompliance

of this machine.

Improper use or maintenance by the operator or owner

can result in injury. To reduce the potential for injury,

comply with these safety instructions and always pay

attention to the safety alert symbol, which means

CAUTION, WARNING, or DANGER—“personal

safety instruction.” Failure to comply with the

instruction may result in personal injury or death.

Safe Operating Practices

The following instructions are from ANSI standard

B71.4—2004.

Training

• Read the Operator’s Manual and other training material.

If the operator(s) or mechanic(s) can not read English it

is the owner’s responsibility to explain this material to

them.

• Become familiar with the safe operation of the

equipment, operator controls, and safety signs.

• All operators and mechanics should be trained. The

owner is responsible for training the users.

• Never let children or untrained people operate or

service the equipment. Local regulations may restrict

the age of the operator.

• The owner/user can prevent and is responsible for

accidents or injuries occurring to himself or herself,

other people or property.

Preparation

• Evaluate the terrain to determine what accessories and

attachments are needed to properly and safely perform

the job. Only use accessories and attachments approved

by the manufacturer.

• Wear appropriate clothing including hard hat, safety

glasses and hearing protection. Long hair, loose

clothing or jewelry may get tangled in moving parts.

• Inspect the area where the equipment is to be used and

remove all objects such as rocks, toys and wire which

can be thrown by the machine.

• Use extra care when handling gasoline and other fuels.

They are flammable and vapors are explosive.

• Use only an approved container

• Never remove gas cap or add fuel with engine

running. Allow engine to cool before refueling.

Do not smoke.

• Never refuel or drain the machine indoors.

• Check that operator’s presence controls, safety switches

and shields are attached and functioning properly. Do

not operate unless they are functioning properly.

Operation

• Never run an engine in an enclosed area.

• Only operate in good light, keeping away from holes

and hidden hazards.

• Be sure all drives are in neutral and parking brake is

engaged before starting engine. Only start engine from

the operator’s position.

• Be sure of your footing while using this machine,

especially when backing up. Walk, don’t run. Never

operate on wet grass. Reduced footing could cause

slipping.

• Slow down and use extra care on hillsides. Be sure to

travel side to side on hillsides. Turf conditions can

affect the machine’s stability. Use caution while

operating near drop-offs.

• Slow down and use caution when making turns and

when changing directions on slopes.

• Never raise deck with the blades running.

• Never operate with the PTO shield, or other guards not

securely in place. Be sure all interlocks are attached,

adjusted properly, and functioning properly.

• Never operate with the discharge deflector raised,

removed or altered, unless using a grass catcher.

• Do not change the engine governor setting or overspeed

the engine.

• Stop on level ground, disengage drives, engage parking

brake (if provided), shut off engine before leaving the

operator’s position for any reason including emptying

the catchers or unclogging the chute.

• Stop equipment and inspect blades after striking objects

or if an abnormal vibration occurs. Make necessary

repairs before resuming operations.

• Keep hands and feet away from the cutting unit.

• Look behind and down before backing up to be sure of

a clear path.

• Keep pets and bystanders away.

• Slow down and use caution when making turns and

crossing roads and sidewalks. Stop blades if not

mowing.

• Be aware of the mower discharge direction and do not

point it at anyone.

• Do not operate the mower under the influence of

alcohol or drugs.

• Use care when loading or unloading the machine into or

from a trailer or truck.

• Use care when approaching blind corners, shrubs, trees,

or other objects that may obscure vision.

Maintenance and storage

• Disengage drives, set parking brake, stop engine and

remove key or disconnect spark plug wire. Wait for all

movement to stop before adjusting, cleaning or

repairing.

• Clean grass and debris from cutting unit, drives,

mufflers, and engine to help prevent fires. Clean up oil

or fuel spillage.

• Let engine cool before storing and do not store near

flame.

• Shut off fuel while storing or transporting. Do not store

fuel near flames or drain indoors.

• Park machine on level ground. Set parking brake. Never

allow untrained personnel to service machine.

• Use jack stands to support components when required.

• Carefully release pressure from components with stored

energy.

• Remove spark plug wire before making any repairs.

• Use care when checking blades. Wrap the blade(s) or

wear gloves, and use caution when servicing them.

Only replace blades. Never straighten or weld them.

• Keep hands and feet away from moving parts. If

possible, do not make adjustments with the engine

running.

• Keep all parts in good working condition and all

hardware tightened. Replace all worn or damaged

decals.

Toro Mower Safety

The following list contains safety information specific to

Toro products and other safety information you must know.

This product is capable of amputating hands and feet and

throwing objects. Always follow all safety instructions to

avoid serious injury or death.

This product is designed for cutting and recycling grass or,

when equipped with a grass bagger, for catching cut grass.

Any use for purposes other than these could prove

dangerous to user and bystanders.

General Operation

• Allow only responsible adults who are familiar with the

instructions to operate the machine.

• Be sure the area is clear of other people before mowing.

Stop the machine if anyone enters the area.

• Do not mow in reverse unless absolutely necessary.

Always look down and behind before and while

backing.

• Be aware of the mower discharge direction and do not

point it at anyone. Do not operate the mower without

either the entire grass catcher or the guard in place.

• Slow down before turning. Sharp turns on any terrain

may cause loss of control.

• Turn off blades when not mowing.

• Keep hands, feet, hair and loose clothing away from

attachment discharge area, underside of mower and any

moving parts while engine is running.

• Stop the engine before removing the grass catcher or

unclogging the chute.

• Mow only in daylight or good artificial light.

• Watch for traffic when operating near or crossing

roadways.

• Do not touch equipment or attachment parts which may

be hot from operation. Allow to cool before attempting

to maintain, adjust or service.

• Use only Toro-approved attachments. Warranty may be

voided if used with unapproved attachments.

Slope Operation

Slopes and ramps are a major factor related to

loss-of-control and accidents, which can result in severe

injury or death. All slopes and ramps require extra caution.

If you feel uneasy on a slope, do not mow it.

• Remove obstacles such as rocks, tree limbs, etc. from

the mowing area.

• Watch for holes, ruts or bumps. Tall grass can hide

obstacles.

• Use slow speed so that you will not have to stop while

on the slope.

• Use extra care with grass catchers or other attachments.

These can change the stability of the machine.

• Keep all movement on slopes slow and gradual. Do not

make sudden changes in speed or direction.

• Avoid starting or stopping on a slope. If tires lose

traction, disengage the blades.

• Check carefully for overhead clearances (i.e. branches,

doorways, electrical wires) before driving under any

objects and do not contact them.

• Mow slopes side to side.

DO NOT

• Do not mow slopes greater than 15 degrees.

• Avoid turning on slopes. If you must turn, turn slowly

and gradually downhill, if possible.

• Do not mow near drop-offs, ditches, or embankments.

The machine could suddenly turn over if a wheel goes

over the edge of a cliff or ditch, or if an edge caves in.

• Do not mow on wet grass. Reduced traction could cause

sliding.

• Do not use a grass catcher on steep slopes. Heavy grass

bags could cause loss of control of the machine.

• Do not mow up and down slopes.

Service

• Never store the machine or fuel container inside where

there is an open flame, such as near a water heater or

furnace.

• Keep nuts and bolts tight, especially the blade

attachment bolts. Keep equipment in good condition.

• Never tamper with safety devices. Check safety systems

for proper operation before each use.

• Use only genuine replacement parts to ensure that

original standards are maintained.

• Check brake operation frequently. Adjust and service as

required.

Slope Chart

Fold along appropriate line

Align this edge with a vertical surface

(Tree, Building, Fence post, pole, etc.)

Example: Compare

slope with folded

edge.

Safety and Instruction Decals

Safety decals and instructions are easily visible to the operator and are located near any area

of potential danger. Replace any decal that is damaged or lost.

1-403005

93-1122

1-523552

66-1340

95-2814

95-5537

1. Read the Operator’s Manual for instructions on operating the

cutting blade

2. Push forward to engage

3. Pull back to disengage

98-0776

98-5130

1. Warning—read the Operator’s Manual for instructions on

torquing the blade bolt/nut to 75-80 ft.-lb.(102-106 N⋅m).

98-5954

99-3943

1. Engine

105-4109

105-4110

106-0699

106-2743

106-0829

1. Forward

2. Neutral

3. Reverse

4. Warning—wear hearing

protection.

5. Fast

6. Continuous variable setting

7. Slow

8. Neutral

Gasoline and Oil

Recommended Gasoline

Use unleaded regular gasoline suitable for automotive use

(85 pump octane minimum). Use leaded regular gasoline if

unleaded regular is not available.

Important Never use methanol, gasoline containing

methanol, or gasohol containing more than 10% ethanol

because the fuel system could be damaged. Do not mix oil

with gasoline.

Danger

In certain conditions, gasoline is extremely

flammable and highly explosive. A fire or

explosion from gasoline can burn you and others

and can damage property.

• Fill the fuel tank outdoors, in an open area,

when the engine is cold. Wipe up any gasoline

that spills.

• Never fill the fuel tank inside an enclosed trailer.

• Do not fill the fuel tank completely full. Add

gasoline to the fuel tank until the level is 1/4 to

1/2 in. (6 to 13 mm) below the bottom of the

filler neck. This empty space in the tank allows

gasoline to expand.

• Never smoke when handling gasoline, and stay

away from an open flame or where gasoline

fumes may be ignited by a spark.

• Store gasoline in an approved container and

keep it out of the reach of children. Never buy

more than a 30-day supply of gasoline.

• Always place gasoline containers on the ground

and away from your vehicle before filling.

• Do not fill gasoline containers inside a vehicle or

on a truck or trailer bed because interior

carpets or plastic truck bed liners may insulate

the container and slow the loss of any static

charge.

• When practical, remove gas-powered equipment

from the truck or trailer and refuel the

equipment with its wheels on the ground.

• If this is not possible, then refuel such

equipment on a truck or trailer from a portable

container, rather than from a gasoline dispenser

nozzle.

• If a gasoline dispenser nozzle must be used, keep

the nozzle in contact with the rim of the fuel

tank or container opening at all times until

fueling is complete.

Gasoline is harmful or fatal if swallowed.

Long-term exposure to vapors can cause serious

injury and illness.

• Avoid prolonged breathing of vapors.

• Keep face away from nozzle and gas tank or

conditioner opening.

• Keep gas away from eyes and skin.

Warning

Using Fuel

Stabilizer/Conditioner

Use a fuel stabilizer/conditioner in the machine to provide

the following benefits:

• Keeps gasoline fresh during storage of 90 days or less

(For longer storage, drain the fuel tank.)

• Cleans the engine while it runs

• Eliminates gum-like varnish buildup in the fuel system,

which causes hard starting

Important Do not use fuel additives containing

methanol or ethanol.

Add the correct amount of gas stabilizer/conditioner to the

gas.

Note: A fuel stabilizer/conditioner is most effective when

mixed with fresh gasoline. To minimize the chance of

varnish deposits in the fuel system, use fuel stabilizer at all

times.

Filling the Fuel Tank

1. Disengage the power take off (PTO) and turn the engine

off.

2. Wait for all moving parts to stop before leaving the

operating position and then set the parking brake.

3. Clean around the fuel tank cap and remove the cap. Add

unleaded regular gasoline to the fuel tank until the level

is 1/4 to 1/2 inch (6 mm to 13 mm) below the bottom of

the filler neck. This space in the tank allows gasoline to

expand. Do not fill the fuel tank completely full.

4. Install the fuel tank cap securely. Wipe up any spilled

gasoline.

Checking the Engine Oil Level

Before you start the engine and use the machine, check the

oil level in the engine crankcase; refer to Checking the

Engine Oil Level, page 31.

Setup

Note: Determine the left and right sides of the machine from the normal operating position.

Loose Parts

Note: Use the chart below to verify all parts have been shipped.

DESCRIPTION QTY. USE

Caster assemblies

Bolt, 3/8 x 3/4 inch

Flange nut, 3/8 inch

Installing the front casters

Upper handle

Flanged bolt, 3/8 x 1 inch

Flanged nut, 3/8 inch

Spring washer

Wire tie

Installing the upper handle and wire harness

Hairpin cotter 1 Installing the blade control rod

Clevis pin

Hairpin cotter

Installing the control rods

Washer

Hairpin cotter

Installing the drive linkage

Clevis pin

Hairpin cotter

Installing the speed control rod

Fuel tank

Bolt, 5/16 x 3/4 inch

Lock washer, 5/16 inch

Locknut

Washer, 5/16 inch

Stud

Spring

Installing the fuel tank

Operator’s Manual

Engine Operator’s Manual

Parts Catalog

Video

Review before operating machine

Registration card 1 Fill out and return to Toro

Installing the Front Casters

1. Align the casters with the holes on the top and front of

the mower, and insert 8 bolts (3/8 x 3/4 inch) through

the mower. Secure the caster with 8 flange nuts

(3/8 inch) below the mower (Fig. 2).

m–3777

Figure 2

1. Front caster

2. Bolt

3. Flange nut

Note: Tighten the lower bolts first to pull the caster

against the front, then tighten the top bolts.

2. Torque the bolts to 30–35 ft.-lb. (40–47 NSm).

Installing the Upper Handle

1. Align the holes in upper handle with the mounting holes

in the rear frame and bracket (Fig. 3).

m–5969

Figure 3

1. Upper handle

2. Rear frame bracket

3. Flange bolt (26 mm)

4. Spring washer

5. Flange nut

Important Install the flange bolts with the bolt head on

the outside of the upper handle. Refer to figure 3.

2. Secure each leg of the upper handle to the rear frame

and bracket with two flange bolts (3/8 x 1 inch

(26 mm), spring washers and flange nuts (Fig. 3).

Tighten until spring washers are compressed.

3. Route the wire harness along the inside of the left

handle and under the control panel (Fig. 17).

4. Connect the right-angled insulated terminals to the

switch (Fig. 4).

m–6490

Figure 4

1. Switch 2. Right-angled insulated

terminals

5. Use the wire ties to secure the wire harness to the inside

of the left handle, away from the blade control (PTO)

rod (Fig. 17). Secure at bottom and top of handle.

Connecting the Throttle Cable

1. Place throttle control lever in the fast position (Fig. 5).

2. Hook wire Z–bend into hole of speed control lever

(Fig. 5).

3. Loosen cable clamp screw allowing cable installation,

but do not tighten (Fig. 5).

4. Move control cable casing and wire until hole in speed

control lever is aligned with hole in base plate. Insert a

1/4 in. (6 mm) diameter pin or bolt into aligned holes to

hold adjustment.

5. Pull throttle cable slightly to remove any slack and

tighten cable clamp screw to lock adjustment in place.

6. Remove alignment pin and check control operation.

m–2596

Figure 5

1. Wire Z-bend

2. Speed control lever

3. Base plate

4. Alignment holes 1/4 in.

(6 mm)

5. Cable clamp

Installing the Blade Control

(PTO) Rod

1. From outer side of bell crank, insert end of blade

control (PTO) rod thru hole (Fig. 6).

m–5997

Figure 6

1. Blade control (PTO) rod

2. Bell crank

3. Hairpin cotter

2. Secure the blade control (PTO) rod to the bell crank

with a hairpin cotter (Fig. 6).

Installing the Control Rods

1. Install the control rod to the drive lever and neutral lock

with a clevis pin and washer (Fig. 7). Washer to be

positioned between drive lever and neutral lock.

2. Install a hairpin cotter between drive lever and washer

and into clevis pin (Fig. 7).

Note: Make sure the clevis pin is inserted into the neutral

lock.

3. Repeat this procedure for the opposite side.

m–5998

Figure 7

1. Left handle shown

2. Neutral lock

3. Clevis pin

4. Drive lever

5. Control rod

6. Operator Presence

Control lever (OPC)

7. Hairpin cotter

4. Thread rod fittings equal distance onto each control rod.

For a starting point, thread rod fittings onto control rod

approximately 2–1/2 inch (64 mm) from the bottom

(Fig. 8).

5. Install rod fittings to idler brackets with clevis pins and

e–ring (Fig. 8).

m–5400

Figure 8

1. Control rod

2. Idler bracket

3. Rod fitting

4. E–ring

5. 2–1/2 inch (64 mm) from

bottom

Installing the Control Arm

Rods

1. Insert control arm swivel thru hole in speed control

crank and secure with hairpin cotter (Fig. 9).

m–5994

Figure 9

1. Control arm

2. Swivel

3. Speed control crank

2. Repeat this procedure for the opposite side.

Installing the Speed Control

Rod

1. Move the speed control lever fully forward (Fig. 10).

Figure 10

1. Speed control lever

2. Install speed control rod to right side of speed control

lever (under control panel) with a hair pin cotter

(Fig. 11).

m–5996

Figure 11

1. Speed control rod

2. Speed control lever

3. Hair pin cotter

3. Install yoke end of speed control rod to the speed

control crank with a clevis pin and hairpin cotter

(Fig. 12).

Figure 12

1. Speed control rod

2. Yoke

3. Speed control crank

4. Hair pin cotter

5. Clevis pin

Installing the Fuel Tank

1. Apply retaining adhesive, such as Loctite RC 609 or

680, to the threads of the 2 threaded studs (5/16 x

7/8 inch) supplied in loose parts. Install studs into the

two left holes in underside of fuel tank

2. Align the fuel tank to the top of the rear frame, and

secure the right side of the fuel tank with 2 bolts (5/16 x

3/4 inch), 2 lock washers (5/16 in.), and 2 washers

(5/16 in.) (Fig. 13).

m-6488

Figure 13

1. Bolt, 5/8 x 7/8 inch (2)

2. Lock washer, 5/16 inch

(2)

3. Washer, 5/16 inch (2)

4. Stud (2)

5. Spring (2)

6. Locknut (2)

3. Secure the fuel tank studs to the frame with 2 washers

(5/16 in.), 2 springs, and 2 locknuts (5/16 in.) (Fig. 13).

Note: Tighten the left side of the fuel tank until it is

completely tight, then unscrew the locknut one full turn.

This allows the spring to work.

4. Push the fuel line onto the fuel tank fitting, and secure

the fuel line with a hose clamp (Fig. 14).

m–6442

Figure 14

1. Fuel line

2. Hose clamp

3. Fuel fitting

Setting up the Hydro Linkage

Perform the following adjustments when the machine is

first set up and when any adjustment is needed. Do them in

the order that they are listed here.

Adjusting the Speed Control Linkage

Refer to Adjusting the Speed Control Linkages on page 37.

Adjusting the Neutral Control Linkages

Refer to Adjusting the Neutral Control Linkages on

page 38.

Adjusting the Hydro Control Linkages

Refer to Adjusting the Hydro Control Linkages on page 39.

Adjusting the Control Rods

Refer to Adjusting the Control Rods on page 41.

Adjusting the Tracking

Refer to Adjusting the Tracking on page 41.

Checking the Hydraulic Fluid

Check the hydraulic fluid level before engine is first

started.

Check the hydraulic fluid level after first 8 operating hours.

Check the hydraulic fluid level after every 25 operating

hours.

Fluid Type: Mobil 1 15W-50 synthetic motor oil or

equivalent synthetic oil.

Important Use oil specified or equivalent. Other fluids

could cause system damage.

Hydraulic System Oil Capacity: 77 oz. (2.3 l)

Note: There are two ways of checking the hydraulic oil.

One is when the oil is warm and one is when the oil is cold.

The baffle inside the tank has two levels depending if the

oil is warm or cold.

1. Position machine on a level surface.

2. Disengage the power take off (PTO) and turn the engine

off.

3. Wait for all moving parts to stop before leaving the

operating position and then set the parking brake.

4. Clean area around cap and filler neck of hydraulic tank

(Fig. 15).

m–5615

Figure 15

1. Cap

2. Baffle

3. Cold fluid level—full

4. Hot fluid level—full

5. Remove cap from filler neck. Look inside to check if

there is fluid in the reservoir. (Fig. 15).

6. If there is no fluid, add fluid to the reservoir until it

reaches the cold level of the baffle.

7. Run the machine at low idle for 15 minutes to allow any

air to purge out of the system and warm fluid. Refer to

Starting and Stopping the Engine on page 20.

8. Recheck the fluid level while the fluid is warm. If

required, add fluid to the reservoir until it reaches the

hot level of the baffle.

Note: The fluid level should be to the top of the hot level

of the baffle, when the fluid is warm (Fig. 15).

9. Install cap on filler neck.

Hydraulic fluid escaping under pressure can

penetrate skin and cause injury.

• If hydraulic fluid is injected into the skin it must

be surgically removed within a few hours by a

doctor familiar with this type of injury.

Gangrene may result if this is not done.

• Keep body and hands away from pin hole leaks

or nozzles that eject high pressure hydraulic

fluid.

• Use cardboard or paper to find hydraulic leaks.

• Safely relieve all pressure in the hydraulic

system before performing any work on the

hydraulic system.

• Make sure all hydraulic fluid hoses and lines are

in good condition and all hydraulic connections

and fittings are tight before applying pressure to

hydraulic system.

Warning

Operation

Note: Determine the left and right sides of the machine

from the normal operating position.

Think Safety First

Carefully read all the safety instructions and decals in the

safety section. Knowing this information could help you,

your family, pets or bystanders avoid injury.

The use of protective equipment for eyes, hearing, feet and

head is recommended.

This machine produces sound levels in excess of

85dBA at the operator’s ear and can cause hearing

loss through extended periods of exposure.

Wear hearing protection when operating this

machine.

Caution

Figure 16

1. Caution 2. Wear hearing protection

Controls

Become familiar with all the controls (Fig. 17) before you

start the engine and operate the machine.

Throttle control – The throttle control has Choke, Fast,

Slow and Stop positions.

Operator Presence Control (OPC) levers – When you

squeeze the OPC levers against the handles, the OPC

system senses that the operator is in the normal operating

position. When you release the OPC levers, the OPC

system senses that the operator has left the normal

operating position, and the system will stop the engine if

either the speed control lever is not in the Neutral position

or the blade control (PTO) lever is engaged.

Blade control knob (PTO) – Push/pull knob is used in

conjunction with OPC levers to drive mower blades.

Speed control lever – This machine has a variable speed

control with a neutral position. This controls how fast the

machine will travel.

Drive levers – Release drive levers to engage forward

traction operation and squeeze to reverse. Squeeze right

side of drive lever to turn right and left side to turn left.

Neutral lock – Squeeze drive levers back and move locks

to the rear for neutral lock. Squeeze drive levers back and

move locks to the front for parking brake lock.

Recoil Starter – Pull recoil starter handle to start engine.

Fuel Shut–off Valve – (Inline) Close fuel shut–off valve

when transporting or storing mower.

Parking Brake Lever – The parking brake lever is on the

right side. Pull up on the brake lever to set the parking

brake.

m–6487

Figure 17

1. Throttle control

2. Operator Presence

Control levers (OPC)

3. Blade control knob (PTO)

4. Drive lever

5. Neutral lock

6. Ignition switch

7. Speed control lever

Operating the Parking Brake

Always set the parking brake when you stop the machine or

leave it unattended. Before each use, check the parking

brake for proper operation.

If the parking brake does not hold securely, adjust it. Refer

to Servicing the Brake on page 33.

Children or bystanders may be injured if they

move or attempt to operate the machine while it is

unattended.

Always remove set the parking brake when leaving

the machine unattended, even if just for a few

minutes.

Caution

Setting the Parking Brake

Pull the parking brake lever rearward (Fig. 21).

m-6102

Figure 18

1. Parking brake lever (in the released position)

Releasing the Parking Brake

Push the parking brake lever forward.

Starting and Stopping the

Engine

Starting

1. Connect the wires to the spark plugs.

2. Open the fuel valve.

Note: A cold weather staring kit has been incorporated to

assist engine starting in cold weather or when the unit has

not been run for a period of time.

To use cold start kit:

• Grasp split ring (Fig. 19) on right side of machine,

pull ring and chain straight out from side of machine

and hook ring over control shield bolt.

m–6473

Figure 19

1. Split ring 2. Control shield bolt

• After engine is started, pull chain straight out from

side of machine until ring can be removed from

shield bolt. Slowly release tension on chain.

3. Disengage the blade control (PTO) and move the speed

control lever to neutral.

4. Move the drive levers to neutral and set the neutral

locks.

5. Set the parking brake.

6. Move the speed control lever to neutral.

7. Move the throttle control to the choke position before

starting a cold engine.

8. Grasp the recoil starter handle firmly and pull it out

until positive engagement results; then pull the handle

vigorously to start the engine. Allow the rope to recoil

slowly.

Stopping

1. Move the throttle lever to slow (Fig. 20).

2. Move drive levers to neutral and set neutral locks.

3. Disengage the blade control (PTO) and move the speed

control lever to neutral.

4. Let engine idle for 30 to 60 seconds before turning the

engine off.

5. To stop the engine, pull the throttle all the way back to

stop (Fig. 20).

Page is loading ...

Toro Mid-Size ProLine Pistol Grip Hydro, 15 HP User manual

Brand: Toro

Model: Mid-Size ProLine Pistol Grip Hydro, 15 HP

Category: Lawnmowers

Type: User manual

Download PDF

report

Toro Mid-Size ProLine Pistol Grip Hydro, 15 HP User manual

Toro Mid-Size ProLine Pistol Grip Hydro, 15 HP User manual

Related papers

Other documents