Digital Watchdog DWC-MV85DiA Installation guide

Brand
Digital Watchdog
Model
DWC-MV85DiA
Type
Installation guide
Step 1 – PREPARING TO MOUNT THE CAMERA
Step 3 – INSTALLING THE CAMERA
Step 2 – CABLING THE CAMERA TO EXTERNAL DEVICES
1. The mounting surface must bear ve times the weight of your camera.
2. Do not let the cables get caught in improper places or the electric line cover
to be damaged. This may cause a breakdown or re.
3. For the installation process, remove the dome cover from the camera module
by loosening the three (3) screws on the dome. Use the wrench provided with
the camera.
4. Using the mounting template sheet or the camera itself, mark and drill the
necessary holes in the wall or ceiling.
6. For soft installation surfaces, use the included metal mount plate. Fix the
mount plate on the mounting surface using the included screws. Then, press
the bottom case onto the mount plate. The three bezels on the case will align
and snap lock onto the plate.
7. Use the camera’s 3-Axis gimbal to adjust the camera’s tilt and angle.
The camera’s maximum tilting angle is 75°.
8. Assemble the dome cover over the camera body and detach the protecting
lm from the dome bubble.
5. Pass the wires through the mount bracket and make all necessary
connections.
a. NETWORK CONNECTIONS – If you are using a PoE Switch, connect the
camera using an Ethernet cable for both data and power.
b. NETWORK CONNECTIONS – If you are using a non-PoE switch, connect
the camera to the switch using an Ethernet cable for data transmission
and use a power adapter to power the camera.
1
2
3
5
4
Template
Sheet
Resetting the camera: To reset the camera, use the tip of a paper clip
or a pencil and press the reset button. Pressing the button for ve (5)
seconds will initiate a camera-wide reset of all the settings, including
network settings.
WARNING DO NOT TOUCH THE SURFACE OF THE BUBBLE.
CleanView
™
Hydrophobic Dome Coating has been
applied to the camera’s dome.
Reset
Button
WHAT’S IN THE BOX
QSG Manual 1 Set Mount Plate 1 Set
Template
Sheet for
installing by
Bolt & Nut
1 Set
Screw &
Plastic Anchor
– 3pcs
1 Set
Template
Sheet for
installing by
Plate
1 Set Tor x Wrench 1 Set
Mount Bolt &
Nut – 2pcs
1 Set
Power
Ethernet
Cable
Ethernet
Cable
5
a
5
b
Quick Start Guide Quick Start Guide
NOTE: Download All Your Support Materials and Tools in One Place
1. Go to: http://www.digital-watchdog.com/support-download/
2. Search your product by entering the part number in the ‘Search by Product’
search bar. Results for applicable part numbers will populate automatically
based on the part number you enter.
3. Click ‘Search’. All supported materials, including manuals, Quick Start Guides
(QSG), software and rmware will appear in the results.
Installation using Mount Bolt and Screws:
9. Using the template sheet, make and drill the cabling holes on the wall/ceiling.
10. Secure the two long mounting screws to the camera’s base.
11. Pass the wires through the mount bracket and make all necessary
connections.
12. Mount the camera to the mounting surface by using the 2 mounting nuts.
Rotate the locking discs over the screws until the camera is held tightly from
the mounting surface.
NOTE: The camera’s maximum tilting angle is 75°
DWC-MV85DiA
Default Login Information
Username: admin Password: admin
Attention: This document is intended to serve as a quick reference for initial
set-up. It is recommended that the user read the entire instruction manual
for complete and proper installation and usage.
Power Requirements Power Consumption
DC 12V
PoE IEEE 802.3af
Auto Focus Working MAX 7.5W
LED On: 7.2W / LED Off: 5.0W
Tel: 866-446-3595 / 813-888-9555
Technical Support Hours:
9:00AM – 8:00PM EST, Monday thru Friday
digital-watchdog.com
NOTE: Please see the full product manual for web viewer setup,
functions and camera settings options.
7. To view the camera’s web viewer, click on ‘View Camera Website’.
8. To save the changes made to the camera’s settings, input the ID and PW of
the camera for authentication and click ‘Save’.
9. If the camera needs to be rebooted after the settings were changed, press
the ‘Reboot’ button. The camera will cycle power and will appear back in the
search results once the reboot is complete.
6. The camera’s default network
information is:
Step 6 – DW IP FINDER
™
Use the DW IP Finder
™
software to scan the network and detect all MEGApix
®
cameras, set the camera’s network settings or access the camera’s web client.
Rev Date: 12/16
Copyright © Digital Watchdog. All rights reserved.
Specications and pricing are subject to change without notice.
Step 7 – WEB VIEWER
Step 4 – CABLING
Select DHCP if the internet service is dynamic IP. This will allow the camera to
receive its IP address from the DHCP server.
Select STATIC to manually enter the camera’s IP address, subnet mask,
Gateway and DNS information.
Contact your network administrator for more information.
‘Port Forwarding’ has to be set in your network’s router for external access
to the camera.
Step 5 – MANAGING THE SD CARD
1. To install the camera’s SD Card, locate the SD card slot in the back of the
camera module.
2. Insert a class 10 SD card into the SD card slot by pressing the SD card slot.
3. To remove the SD Card, press the card inward to release from the card slot.
Default ID / PW : admin / admin
WARNING DO NOT TOUCH THE SURFACE OF THE BUBBLE.
CleanView
™
Hydrophobic Dome Coating has been
applied to the camera’s dome.
Network Setup
1. Go to: http://www.digital-watchdog.com
2. Search for ‘IP Finder’ on the quick search bar at the top of the page.
3. The latest IP Finder software will appear in the search results. Click on the
link to download the le to your computer.
4. The software will scan your network for all supported cameras and display
the results in the table. Allow up to 5 seconds for the IP Finder to nd the
camera on the network.
5. Select a camera from the list by double-clicking on the camera’s image
or clicking on the ‘Click’ button under the IP Conf. column. The camera’s
network information will appear. If necessary, you can adjust the camera’s
network type.
Quick Start Guide
Use the diagram below to properly connect power, network, audio, alarm and
sensors to the camera.
AUDIO
INPUT
AUDIO
OUTPUT
POWER
NETWORK
ALARM
OUTPUT
ALARM
INPUT
Once the camera’s network settings have been setup properly, you can access
the camera’s web viewer using the DW IP Finder
™
. To open the camera’s web
viewer:
1. Find the camera using the DW IP Finder
™
.
2. Double-click on the camera’s view in the results table.
3. Press the ‘View Camera Website.’ The camera’s web viewer will open up in
your default web browser.
4. Enter the camera’s username and password (default are admin / admin).
5. If you are accessing the camera for the rst time, install the ActiveX les in
order to view video from the camera.
Search for Cameras
Camera’s
Network Settings
View Camera’s
Thumbnail View
Camera’s Firmware
Camera Uptime
Open Camera’s IP
Conguration Screen
Filter Search Results
Camera Name,
Model, IP Address,
and MAC Address
Firmware Upgrade
Default TCP/IP information
• IP: DHCP
  • Page 1 1
  • Page 2 2

Digital Watchdog DWC-MV85DiA Installation guide

Brand
Digital Watchdog
Model
DWC-MV85DiA
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents