TP-LINK TL-WA750RE User guide

Category
Network extenders
Type
User guide
TL-WA750RE
150Mbps Universal Wi-Fi Range Extender
REV 1.3.2
1910011
329
COPYRIGHT & TRADEMARKS
Specifications are subject to change without notice. is a registered trademark of
TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or
registered trademarks of their respective holders.
No part of the specifications may be reproduced in any form or by any means or used to make any
derivative such as translation, transformation, or adaptation without permission from TP-LINK
TECHNOLOGIES CO., LTD. Copyright © 2015 TP-LINK TECHNOLOGIES CO., LTD.
All rights reserved.
http://www.tp-link.com
FCC STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
Consult the dealer or an experienced radio/ TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:
1) This device may not cause harmful interference.
2) This device must accept any interference received, including interference that may
cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
Note: The manufacturer is not responsible for any radio or tv interference caused by unauthorized
modifications to this equipment. Such modifications could void the user’s authority to operate the
equipment.
FCC RF Radiation Exposure Statement
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled
environment. This device and its antenna must not be co-located or operating in conjunction with
any other antenna or transmitter.
“To comply with FCC RF exposure compliance requirements, this grant is applicable to only
Mobile Configurations. The antennas used for this transmitter must be installed to provide a
separation distance of at least 20 cm from all persons and must not be co-located or operating in
conjunction with any other antenna or transmitter.”
CE Mark Warning
This is a class B product. In a domestic environment, this product may cause radio interference, in
which case the user may be required to take adequate measures.
This device has been designed to operate with the antennas listed below, and having a maximum
gain of 3 dBi. Antennas not included in this list or having a gain greater than 3 dBi are strictly
prohibited for use with this device. The required antenna impedance is 50 ohms.
To reduce potential radio interference to other users, the antenna type and its gain should be so
chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that permitted for
successful communication.
Canadian Compliance Statement
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject
to the following two conditions:
(1)This device may not cause interference, and
(2)This device must accept any interference, including interference that may cause undesired
operation of the device.
Cet appareil est conforme aux norms CNR exemptes de licence dIndustrie Canada. Le
fonctionnement est soumis aux deux conditions suivantes:
(1)cet appareil ne doit pas provoquer d’interférences et
(2)cet appareil doit accepter toute interférence, y compris celles susceptibles de provoquer un
fonctionnement non souhaité de l’appareil.
Industry Canada Statement
Complies with the Canadian ICES-003 Class B specifications.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
This device complies with RSS 210 of Industry Canada. This Class B device meets all the
requirements of the Canadian interference-causing equipment regulations.
Cet appareil numérique de la Classe B respecte toutes les exigences du Règlement sur le
matériel brouilleur du Canada.
Korea Warning Statements
당해 무선설비는 운용중 전파혼 가능성이 있음.
NCC Notice & BSMI Notice
注意!
依據 低功率電波輻射性電機管理辦法
第十二條 經型式認證合格之低功率射頻電機,費經許可,公司、商號或使用者均不得擅自變更頻
率、加大功率或變更原設計之特性或功能。
第十四條 低功率射頻電機之使用不得影響飛航安全及干擾合法通行;經發現有干擾現象時,應立
即停用,并改善至無干擾時方得繼續使用。前項合法通信,指依電信規定作業之無線電信。低功
射頻電機需忍受合法通信或工業、科學以及醫療用電波輻射性電機設備之干擾。
減少電磁波影響,請妥適使用。
安全諮詢及注意事項
請使用原裝電源供應器或只能按照本產品注明的電源類型使用本產品。
清潔本產品之前請先拔掉電源線。請勿使用液體、噴霧清潔劑或濕布進行清潔。
注意防潮,請勿將水或其他液體潑灑到本產品上。
插槽與開口供通風使用,以確保本產品的操作可靠並防止過熱,請勿堵塞或覆蓋開口。
請勿將本產品置放於靠近熱源的地方。除非有正常的通風,否則不可放在密閉位置中。
請不要私自打開機殼,不要嘗試自行維修本產品,請由授權的專業人士進行此項工作。
Продукт сертифіковано згідно с правилами системи УкрСЕПРО на відповідність вимогам
нормативних документів та вимогам, що передбачені чинними законодавчими актами
України.
Safety Information
When product has power button, the power button is one of the way to shut off the product;
when there is no power button, the only way to completely shut off power is to disconnect the
product or the power adapter from the power source.
Don’t disassemble the product, or make repairs yourself. You run the risk of electric shock
and voiding the limited warranty. If you need service, please contact us.
Avoid water and wet locations.
This product can be used in the following countries:
AT
BG
BY
CA
CZ
DE
DK
EE
ES
FI
FR
GB
GR
HU
IE
IT
LT
LV
MT
NL
NO
PL
PT
RO
RU
SE
SK
TR
UA
US
TP-LINK TECHNOLOGIES CO., LTD
DECLARATION OF CONFORMITY
For the following equipment:
Product Description: 150Mbps Universal Wi-Fi Range Extender
Model No.: TL-WA750RE
Trademark: TP-LINK
We declare under our own responsibility that the above products satisfy all the technical
regulations applicable to the product within the scope of Council Directives:
Directives 1999/5/EC, Directives 2004/108/EC, Directives 2006/95/EC, Directives 1999/519/EC,
Directives 2011/65/EU
The above product is in conformity with the following standards or other normative documents
EN 300 328 V1.8.1
EN 301 489-1 V1.9.2 & EN 301 489-17 V2.2.1
EN 55022: 2010 + AC: 2011
EN 55024: 2010
EN 61000-3-2: 2006 + A1: 2009 + A2: 2009
EN 61000-3-3: 2013
EN 60950-1: 2006 + A11: 2009 + A1: 2010 + A12: 2011
EN 50385: 2002
The product carries the CE Mark:
Person responsible for marking this declaration:
Yang Hongliang
Product Manager of International Business
Date of Issue: 2015
TP-LINK TECHNOLOGIES CO., LTD.
Building 24 (floors 1, 3, 4, 5), and 28 (floors 1-4) Central Science and Technology Park,
Shennan Rd, Nanshan, Shenzhen, China
CONTENTS
Package Contents .................................................................................................... 1
Chapter 1 Introduction ........................................................................................... 2
1.1 Product Overview ............................................................................................ 2
1.2 Main Features ................................................................................................. 2
1.3 Appearance ..................................................................................................... 2
Chapter 2 Hardware Installation ........................................................................... 4
2.1 Before You Begin ............................................................................................ 4
2.2 Basic Requirements ........................................................................................ 5
2.3 Connecting the Device .................................................................................... 5
Chapter 3 Quick Installation Guide ....................................................................... 6
Chapter 4 Configure the Device .......................................................................... 10
4.1 Status ............................................................................................................ 10
4.2 Quick Setup ................................................................................................... 11
4.3 Profile ............................................................................................................ 11
4.4 Network ......................................................................................................... 13
4.4.1 LAN .................................................................................................................. 13
4.4.2 DHCP Settings ................................................................................................. 14
4.4.3 DHCP Client List .............................................................................................. 16
4.5 Wireless ........................................................................................................ 17
4.5.1 Wireless Settings ............................................................................................. 17
4.5.2 Wireless Security ............................................................................................. 18
4.5.3 Wireless MAC Filtering .................................................................................... 20
4.5.4 Wireless Advanced .......................................................................................... 22
4.5.5 Wireless Statistics............................................................................................ 23
4.5.6 Throughput Monitor ......................................................................................... 24
4.6 System Tools ................................................................................................. 24
4.6.1 Firmware Upgrade ........................................................................................... 25
4.6.2 Factory Defaults............................................................................................... 26
4.6.3 Backup & Restore ............................................................................................ 26
4.6.4 Reboot ............................................................................................................. 27
4.6.5 Password ......................................................................................................... 28
4.6.6 System Log ...................................................................................................... 28
Appendix A: Factory Defaults ............................................................................... 30
Appendix B: Troubleshooting ............................................................................... 31
Appendix C: Specifications ................................................................................... 33
Appendix D: Glossary ............................................................................................ 34
TL-WA750RE
150Mbps Universal Wi-Fi Range Extender User Guide
Package Contents
The following items should be found in your package:
TL-WA750RE 150Mbps Universal Wi-Fi Range Extender
Ethernet Cable
Quick Installation Guide
Note:
Make sure that the package contains the above items. If any of the listed items is damaged or
missing, please contact your distributor.
Conventions
The Range Extender, the Device or TL-WA750RE mentioned in this User guide stands for
TL-WA750RE 150Mbps Universal Wi-Fi Range Extender without any explanations.
Parameters provided in the pictures are just references for setting up the product, which may differ
from the actual situation. You can set the parameters according to your demand.
The power plug may differ from the picture illustrated in this UG due to different regional power
specifications. Here we just take that of EU version for example.
1
TL-WA750RE
150Mbps Universal Wi-Fi Range Extender User Guide
Chapter 1 Introduction
1.1 Product Overview
The TL-WA750RE 150Mbps Universal Wi-Fi Range Extender is dedicated to Small Office/Home
Office (SOHO) wireless network solutions. It will enlarge your existing wireless network and
mobility within your wireless network while also allowing you to connect a wired device to a
wireless environment. Increased mobility and the absence of cabling will be beneficial for your
network.
With using IEEE 802.11n wireless technology, this device can transmit wireless data at the rate of
up to 150Mbps. With multiple protection measures, including wireless LAN 64/128/152-bit WEP
encryption, Wi-Fi protected Access (WPA2-PSK, WPA-PSK), the TL-WA750RE 150Mbps
Universal Wi-Fi Range Extender delivers complete data privacy.
It supports an easy wireless connection to the root AP (equipped with WPS/QSS button) by
pressing the RE button on the front panel. It also supports an easy, web-based setup for
installation and management. Even though you may not be familiar with the Range Extender, you
can easily configure it with the help of this Guide. Before installing the Range Extender, please
look through this Guide to get the full information of the TL-WA750RE 150Mbps Universal Wi-Fi
Range Extender.
1.2 Main Features
Applies IEEE 802.11n wireless technology
Supports multiple encryption security types including: 64/128/152-bit WEP and
WPA/WPA2-Personal
Supports built-in DHCP server
Supports two operating modes: Range Extender Mode 1 and Range Extender Mode 2
Supports firmware upgrade
Supports web management
1.3 Appearance
Figure 1-1
2
TL-WA750RE
150Mbps Universal Wi-Fi Range Extender User Guide
LED Explanation:
Name Status Indication
RE
On
The Range Extender is connected to your router.
Blinking
The Range Extender is establishing a connection with your router.
Off
The Range Extender is not connected to your router.
Wireless
Blinking
The wireless function is working properly.
Off The wireless function is not working.
Power
On
The Range Extender is on.
Off
The Range Extender is off.
Ethernet
On
The Ethernet port is connected.
Off
The Ethernet port is not connected.
Signal
Strength
On
The number of lit LEDs indicates the strength of wireless signal.
Blinking
A connection to your router has been established, but no Internet
access yet.
Off The Range Extender is not connected to your router.
Table 1-1
(RANGE EXTENDER/WPS): If your Wireless router or AP supports WPS or QSS
function, you can press the WPS or QSS button and then press the RANGE EXTENDER
button to establish a secure connection between the Wireless router (or AP) and the Range
Extender TL-WA750RE.
RESET: This button is used to restore the Range Extender’s factory default settings.
There are two ways to reset the Range Extenders factory defaults:
Method One: With the Range Extender powered on, use a pin to press the RESET button
until all the LEDs turn on momentarily, then release the button and wait the Range Extender
to reboot to its factory default settings.
Method Two: Restore the default settings fromSystem Tools > Factory Defaultsof the
Range Extender's Web-based management page.
ETHERNET: One 10/100Mbps RJ45 Ethernet port used to add wireless connectivity to an
Ethernet-enabled device such as Internet TV, DVR, Gaming console and so on. Please note
that this port is not allowed to be connected with router or AP.
3
TL-WA750RE
150Mbps Universal Wi-Fi Range Extender User Guide
Chapter 2 Hardware Installation
2.1 Before You Begin
Please read this User Guide carefully before installing and using the equipment. The operating
distance range of your wireless connection can vary significantly depending on the physical
position of the wireless devices. Factors that can weaken signals by getting in the way of your
network’s radio waves are metal appliances or obstructions, and walls. Typical ranges vary based
on the types of materials and background RF (radio frequency) noise in your home or office.
In order to optimize the performance of TL-WA750RE, please follow the instructions below to
achieve an ideal location (please make sure it is always within the wireless coverage of the
wireless router).
1) Half-way Between - Generally, the ideal location for TL-WA750RE is half-way between the
Wireless router and Wireless Client. If the wireless signal is not satisfactory, you may place
TL-WA750RE somewhat nearer to the Wireless router.
2) No Obstacles and Spacious - Clear obstacles in the way between TL-WA750RE and
Wireless router. It’s better to locate it in a spacious place, such as near the corridors.
3) No Interference - Keep TL-WA750RE far away from wireless interference, which may come
from electrical appliances that works in the same frequency band as TL-WA750RE, such as
Blue tooth devices, cordless phones, microwave ovens, etc.
4) 3 Signal Lights - You can also find an ideal location via the signal lights on the front panel of
TL-WA750RE. These lights show the strength of signal your range extender receives from
the root AP. It's recommended that you choose a location where at least 3 signal lights light
up, in order to guarantee a good performance.
Note:
TP-LINK recommends that you connect to the Range Extender when your home network
connection is poor, or when you want a larger wireless coverage to eliminate “dead zones”. As in
compliance with the wireless transmission protocol, all the Range Extender devices are set to
work in half-duplex instead of full-duplex mode. In other words, the Range Extender has to
process one-way communication between your root Wireless router (or AP) and the terminal
clients; so the transmission time will be double-increased, while the speed will be decreased.
4
TL-WA750RE
150Mbps Universal Wi-Fi Range Extender User Guide
2.2 Basic Requirements
Place your Range Extender in a well-ventilated place far from direct sunlight, any heater or
heating vent.
Leave at least 2 inches (5cm) space around the device for heat dissipation.
Turn off your Range Extender and unplug the power adapter in a lighting storm to avoid
damage.
Use Web browser, such as Microsoft Internet Explorer 5.0 or above, Netscape Navigator 6.0
or above.
Operating temperature of the Range Extender should be 0~40 (32~104).
Operating humidity of the Range Extender should be 10%~90%RH (Non-condensing).
2.3 Connecting the Device
Figure 2-1 Typical connection of TL-WA750RE
To establish a typical connection of the Range Extender, please take the following steps:
1. Connect the Cable/DSL modem to a Wireless router with an Ethernet cable.
2. Plug your TL-WA750RE directly to a standard electrical wall socket, which is next to the
Wireless router.
3. Connect your Wireless Clients (such as notebook, pad, smart phone, etc.) to TL-WA750RE
wirelessly. Or you can connect your PC to the sole LAN port of Range Extender via an
Ethernet cable.
4. Log in the web-based management page of TL-WA750RE and complete the configurations.
(Please refer to Chapter 3 Quick Installation Guide or Chapter 4 Configure the Device
for the
configurations, as you need.) Through the web page configuration you can successfully
connect
TL-WA750RE to the wireless router.
5. Adjust an ideal location for TL-WA750RE. (Please refer to Section 2.1 Before You Begin
for
detailed information about ideal location.)
5
TL-WA750RE
150Mbps Universal Wi-Fi Range Extender User Guide
Chapter 3 Quick Installation Guide
This chapter will guide you to configure your PC to communicate with the Range Extender and to
configure and manage the TL-WA750RE 150Mbps Universal Wi-Fi Range Extender easily with a
Web-based utility.
With a Web-based utility, it is easy to configure and manage the TL-WA750RE 150Mbps Universal
Wi-Fi Range Extender. The Web-based utility can be used on any Windows, Macintosh or UNIX
OS with a Web browser, such as Microsoft Internet Explorer, Mozilla Firefox or Apple Safari.
1. To access the configuration utility, open a web-browser and type in the domain name
http://tplinkrepeater.net
in the address field of the browser.
Figure 3-1 Login to the Range Extender
After a moment, a login window will appear as shown in Figure 3-2. Enter admin for the User
Name and Password (both in lower case letters). Then click OK or press Enter.
Figure 3-2 Login Windows
Note:
If the above screen does not prompt, it means that your web-browser has been set to a proxy. Go
to Tools menu > Internet Options > Connections > LAN Settings, in the screen that appears,
cancel the Using Proxy checkbox, and click OK to finish it.
6
TL-WA750RE
150Mbps Universal Wi-Fi Range Extender User Guide
2. After successful login, there will pop up the Quick Setup Start page. Click Next to get the
quick setup started.
Figure 3-3 Quick Setup Start
Note:
If you are not to go through the Quick Setup right away, you can click Exit and enter the main
menu of the device.
3. Figure 3-4 will appear for you to choose the region. Then click Next to continue.
Figure 3-4 Quick Setup Choose Region
Note:
Per FCC regulations, all Wi-Fi products marketed in the U.S. must be fixed to the U.S. region
only.
4. The device will detect the existing wireless networks. Please wait for a while.
Figure 3-5 Quick Setup Detect Existing Networks
7
TL-WA750RE
150Mbps Universal Wi-Fi Range Extender User Guide
5. A list of available wireless networks will appear. Check the box before the SSID of your
desired network, and then click Next.
Figure 3-6 Quick Setup Available Wireless Networks
Note:
If you could not find your wireless network name (SSID) in the list, you can click
Rescan
to
redetect it or tick the checkbox before "Set SSID and MAC Manually" to manually configure
the wireless settings.
6. Wireless Settings page will appear as shown in Figure 3-7. Enter the Wi-Fi Password of your
main router/AP, name your range extender Wi-Fi network or keep it default, and then click
Next to continue.
Figure 3-7 Quick Setup Wireless Settings
8
TL-WA750RE
150Mbps Universal Wi-Fi Range Extender User Guide
7. Double-check your wireless setting and network setting on the page as shown in Figure 3-8. If
verified, click Finish to complete the Quick Setup. If there is anything wrong, click Back to
return the previous pages and reconfigure it.
Figure 3-8 Quick Setup Review Settings
Note:
Its recommended to click the Export Settings button to save these settings as a txt file for
your future reference.
8. When the Range Extender is applying the wireless settings (as shown in Figure 3-9), please
wait for a while patiently until Figure 3-10 appears. Then you have successfully extended the
root devices wireless signal.
Figure 3-9 Quick SetupApplying
Figure 3-10 Quick Setup Completed
9
TL-WA750RE
150Mbps Universal Wi-Fi Range Extender User Guide
Chapter 4 Configure the Device
This Chapter describes how to configure your Range Extender via the web-based management
page. The TL-WA750RE 150Mbps Universal Wi-Fi Range Extender is easy to configure and
manage with the Web-based (Internet Explorer, Netscape
®
Navigator, Firefox, Safari, Opera or
Chrome) management page, which can be launched on any windows, Macintosh or UNIX OS with
a web browser.
After a successful login, you can configure and manage the device. There are eight main menus
on the leftmost column of the web-based management page: Status, Quick Setup, Profile,
Network, Wireless, DHCP and System Tools. Submenus will be available after clicking one of
the main menus. On the right of the web-based management page are the detailed explanations
and instructions for the corresponding page.
4.1 Status
Selecting Status will enable you to view the Range Extender’s current status and configuration, all
of which are read-only.
Figure 4-1 Status
Range Extender Info - This part shows you the current information of the Range Extender.
WiFi Name - The Range Extender's wireless network name (also called SSID) which
your PC and other wireless device can be connected to.
MAC Address - The physical address of the system.
DHCP Server - It shows the current status of the DHCP Server of the Range Extender.
Channel - The current wireless channel in use.
10
TL-WA750RE
150Mbps Universal Wi-Fi Range Extender User Guide
Wireless Connection It shows whether the Range Extender is connected to the Main
Router/AP by Wireless.
IP Address The IP address of the Range Extender.
Type The Range Extender's IP address Type.
Signal Received From Main Router/AP - This is the signal strength the Range
Extender received from the Main Router/AP.
Wireless Rate To Main Router/AP - This is the real wireless rate between the Range
Extender and the Main Router/AP.
Main Router/AP Info - This part shows you the current information of the Main Router/AP.
WiFi Name - This is the Wi-Fi name of the Main Router/AP (The Main Router/AP is
usually your router or access point or gateway).
MAC Address - The MAC address of the main Router or AP.
Internet Access - It shows whether the Main Router/AP has access to the Internet.
System Up Time - The length of the time since the device was last powered on or reset.
Firmware Version - This field displays the current firmware version of the Range Extender.
Hardware Version - This field displays the current hardware version of the Range Extender.
Click the Refresh button to get the latest status and settings of the device.
4.2 Quick Setup
Please refer to Chapter 3 Quick Installation Guide.
4.3 Profile
Profile function can help you remember previously connected wireless networks.
You can Edit, Delete or Add profiles in this page (as shown in Figure 4-2) for your convenient
reconnection later on.
Figure 4-2 Profile
Choose - You can choose any one wireless network you want to connect to.
Profile Name - The name you give to your wireless network(s). By default, it's the same as
root SSID, but you can change it to any other names that you can easily remember and
distinguish.
Root SSID - the SSID (wireless network name) of your root device, a wireless router or AP.
11
TL-WA750RE
150Mbps Universal Wi-Fi Range Extender User Guide
MAC - The physical address of your root AP, also called BSSID.
Security Type - The security type of your root device.
Modify - You can Edit or Delete the profile(s).
Click Connect to connect the range extender to the wireless network that you have chosen in the
profile list.
Click Add to add a new profile to the list.
Click Delete All to delete all the information in the profile list.
To add a profile:
1. Click Add in the Profiles list page as shown in Figure 4-2.
2. Configure the required parameters (as shown in Figure 4-3), including name your profile, enter
the SSID of your root device (a wireless router or AP) and its MAC address, select the security
type of your root device and also enter the wireless password. Then click to Save your profile.
Figure 4-3 Add or Modify the Profile
Profile Name - The name you give to your wireless networks. By default, it's the same as
root SSID, but you can change it to any other names that you can easily remember and
distinguish.
Root SSID - The wireless network name of your root AP this profile will connect to.
MAC of Root Device - The MAC of your root device this profile will connect to.
Wireless Security - The security type of your root wireless networks this profile will refer
to. Please make sure it's the same as the root AP's.
Wireless Password - The wireless password of your root AP. Please make sure it's the
same as your root AP.
Click Save to save this profile in the profile list and go back to the Profile List page.
Click Back to go back to the Profile List page, without saving any configuration on this page.
3. After youve set and saved the profile, it will return to the profiles list page and display as in
Figure 4-4.
12
TL-WA750RE
150Mbps Universal Wi-Fi Range Extender User Guide
Figure 4-4 Add or Modify the Profile
Click Edit to further edit the profile(s), or Delete to delete the profile(s).
Click Connect to connect the range extender to the wireless network that you have chosen in
the profiles list.
Click Add to add a new profile to the list.
Click Delete All to delete all the information in the profiles list.
4.4 Network
The Network option allows you to customize your local network manually by changing the default
settings of the Range Extender. There are three submenus under the DHCP menu: LAN, DHCP
Settings and DHCP Client List. Clicking one of them will enable you to configure the
corresponding function. The detailed explanations for each submenu are provided below.
Figure 4-5 Network Menu
4.4.1 LAN
Selecting Network > LAN will enable you to configure the IP parameters of Network on this page.
Figure 4-6 LAN Dynamic IP
13
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42

TP-LINK TL-WA750RE User guide

Category
Network extenders
Type
User guide

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI