Videotec DTWRX User manual

Type
User manual
EN
English - Instructions manual
IT
Italiano - Manuale di istruzioni
FR
Français - Manuel d’instructions
DE
Deutsch - Bedienungslanleitung
RU
 - Руководство по эксплуатации
DTWRX
Telemetry data receiver for wiper and washer remote control
Instruction manual - English - EN
1MNVKDTWRX_1723_EN
ENGLISH
DTWRX
Telemetry data receiver for wiper and washer remote control
1 About this manual
Read all the documentation supplied carefully before
installing and using this unit. Keep the manual in a
convenient place for future reference.
1.1 Typographical conventions
DANGER!
High level hazard.
Risk of electric shock. Disconnect the
power supply before proceeding with any
operation, unless indicated otherwise.
CAUTION!
Medium level hazard.
This operation is very important for the
system to function properly. Please read
the procedure described very carefully and
carry it out as instructed.
INFO
Description of system specications.
We recommend reading this part carefully
in order to understand the subsequent
stages.
2 Notes on copyright and
information on trademarks
The mentioned names of products or companies are
trademarks or registered trademarks.
3 Safety rules
CAUTION! Device installation and
maintaining must be performed by
specialist technical sta only.
The manufacturer declines all responsibility
for any damage caused by an improper use
of the appliances mentioned in this manual.
Furthermore, the manufacturer reserves the right
to modify its contents without any prior notice.
The documentation contained in this manual has
been collected and veried with great care. The
manufacturer, however, cannot take any liability
for its use. The same thing can be said for any
person or company involved in the creation and
production of this manual.
Before starting any operation, make sure the
power supply is disconnected.
Be careful not to use cables that seem worn or old.
Never, under any circumstances, make any
changes or connections that are not shown in
this handbook. Improper use of the appliance
can cause serious hazards, risking the safety of
personnel and of the installation.
Use only original spare parts. Non-original spare
parts could cause re, electrical discharge or other
hazards.
Before proceeding with installation, check the
supplied material to make sure it corresponds
to the order specication by examining the
identication labels (4.2 Product marking, page 2).
EN - English - Instruction manual
2 MNVKDTWRX_1723_EN
4 Identication
4.1 Product description and type
designation
The DTWRX receiver is an optional board for remote
control of wiper and washer pump. It works only
with WASPT pump series, where it can be easily
installed thanks to its connector. It allows the control
of wiper and washer functions when the housing is
stand-alone, not mounted on a P&T and then without
telemetry receiver.
4.2 Product marking
See the label attached to the product.
5 Preparing the product for
use
Any change that is not expressly approved
by the manufacturer will invalidate the
guarantee.
5.1 Unpacking
When the product is delivered, make sure that the
package is intact and that there are no signs that it
has been dropped or scratched.
If there are obvious signs of damage, contact the
supplier immediately.
When returning a faulty product we recommend
using the original packaging for shipping.
Keep the packaging in case you need to send the
product for repairs.
5.2 Contents
Check the contents to make sure they correspond
with the list of materials as below:
Data receiver board
Instruction manual
5.3 Safely disposing of packaging
material
The packaging material can all be recycled. The
installer technician will be responsible for separating
the material for disposal, and in any case for
compliance with the legislation in force where the
device is to be used.
6 Installation
Electrical connections must be performed
with the power supply disconnected and
the circuit-breaker open.
Use cables with the characteristics outlined
below.
Type: twisted cable
Minimum section: 0.5mm² (20AWG).
Maximum length: 1200m.
Congure protocol, baud rate and receiver address
via the DS1 DIP switch (Tab. 1, page3).
Fig. 1
Open the box of the WASPT device.
Connect telemetry lines RS-485 A and B to connector
J9 (WASPT board) as described in the relative manual.
If the receiver is connected to one of the head
communication channels RS-485, the line must be
terminated (SW8 column, Tab. 1, page3).
Insert the DTWRX board in the specic J8 housing
and close the box of the WASPT device.
Fig. 2
Supply power to the device, checking that the
controls function correctly from the start.
Instruction manual - English - EN
3
7 Conguration
DIP SWITCH CONFIGURATION DS1
Description SW 1 SW 2 SW 3 SW 4 SW 5 SW 6 SW 7 SW 8
Address Not available OFF OFF OFF OFF OFF
1 ON OFF OFF OFF OFF
2 OFF ON OFF OFF OFF
3 ON ON OFF OFF OFF
31 ON ON ON ON ON
Protocol and
baud rate
VIDEOTEC MACRO
9600
OFF OFF
VIDEOTEC MACRO
38400
ON OFF
PELCO D 2400 OFF ON
PELCO D 9600 ON ON
RS-485 line
termination
Line terminated ON
Line not terminated OFF
Tab.
1
8 Instructions for normal
operation
8.1 Wiper/Washer commands
If DCJ keyboard with VIDEOTEC MACRO protocol is
used, use the WIPER/WASHER buttons. Pressing
these buttons will activate the relative function,
while releasing them will stop execution. For
further information, refer to the manual of the
keyboard in use.
MNVKDTWRX_1723_EN
For the devices that communicate via the PELCO D
protocol please refer to the relative table.
WIPER/WASHER COMMANDS PELCO D
Action Command
Wiper Start Save Preset 85
Aux 3 ON
Wiper Stop Save Preset 86
Aux 3 OFF
Washer Start Save Preset 87
Aux 4 ON
Washer Stop Save Preset 97
Aux 4 OFF
Tab. 2
MNVKDTWRX_1723_EN
9 Disposal of waste
materials
The European Directive 2012/19/EU on Waste
Electrical and Electronic Equipment (WEEE) mandates
that these devices should not be disposed of in the
normal ow of municipal solid waste, but they should
be collected separately in order to optimize the
recovery stream and recycling of the materials that
they contain and to reduce the impact on human
health and the environment due to the presence of
potentially hazardous substances.
The symbol of the crossed out bin is marked
on all products to remember this.
The waste may be delivered to appropriate collection
centers, or may be delivered free of charge to the
distributor where you purchased the equipment at
the time of purchase of a new equivalent or without
obligation to a new purchase for equipment with size
smaller than 25cm .
For more information on proper disposal of these
devices, you can contact the responsible public
service.
10 Technical data
10.1 General
2 functions: WIPER, WASHER
31 selectable addresses through DIP switch
Serial input RS-485
2 status LED: Stand-by and receiver control
10.2 Mechanical
Dimensions: 43x56x13mm (1.7x2.2x0.51in)
Unit weight: 0.02kg
10.3 Electrical
Power consumption: 0.5W
10.4 Serial communications
Half duplex RS-485 serial interface for keypad
telemetry data reception (maximum distance
1200m/3940ft) and from SM matrix range (maximum
distance 1200m/3940ft)
Protocols:
PELCO D (2400, 9600 baud)
VIDEOTEC MACRO (9600, 38400 baud)
10.5 Environment
For installation indoors and outdoors
Operating temperature: from -25°C up to +60°C
10.6 Certications
Electrical safety (CE): EN60950-1
Electromagnetic compatibility (CE): EN50130-4,
EN61000-6-3, FCC Part 15 (Class B)
EAC certication
11 Technical drawings
The dimensions of the drawings are in
millimetres.
56
43
Fig. 3 DTWRX.
Headquarters Italy Videotec S.p.A.
Via Friuli, 6 - I-36015 Schio (VI) - Italy
Tel. +39 0445 697411 - Fax +39 0445 697414
www.videotec.com
MNVKDTWRX_1723
Headquarters Italy Videotec S.p.A.
Via Friuli, 6 - I-36015 Schio (VI) - Italy
Tel. +39 0445 697411 - Fax +39 0445 697414
France Videotec France SARL
Immeuble Le Montreal, 19bis Avenue du Québec, ZA de Courtaboeuf
91140 Villebon sur Yvette - France
Tel. +33 1 60491816 - Fax +33 1 69284736
Email: info.fr@videotec.com
Asia Pacic Videotec (HK) Ltd
Flat 8, 19/F. On Dak Industrial Building, No. 2-6 Wah Sing Street
Kwai Chung, New Territories - Hong Kong
Tel. +852 2333 0601 - Fax +852 2311 0026
Email: info.hk@videotec.com
Americas Videotec Security, Inc.
Gateway Industrial Park, 35 Gateway Drive, Suite 100
Plattsburgh, NY 12901 - U.S.A.
Tel. +1 518 825 0020 - Fax +1 518 825 0022
Email: info.usa@videotec.com - www.videotec.com
www.videotec.com
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24

Videotec DTWRX User manual

Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI