Indesit MM 060 DSL0 Owner's manual

Page is loading ...

1

2

3

4

5

6

7

8

9

10

11

12

13

15

14

17

18

16

19

Fig. 1

Aling the location hole with the pin

Fig. 2

1

2

Fig. 3 Fig. 4

MM 060 EU

220-240V

600W

B

Aling the location hole

with the pin

Fig. 5

Fig. 6 Fig. 7

Fig. 8

Fig. 9

Page is loading ...

8

iten

PARTS AND FEATURES

1. Funnel

2. Mincer head

3. Lock button

4. ON/OFF button

5. REVERSE button

6. Motor unit

7. Grinding screw

8. Blade

9. Die plate (large hole)

10. Blade cover

11. Spanner

12. Blades-cleaning disk

13. Die plate (small hole)

14. Die plate (medium hole)

15. Sausage ller’s nozzle support

16. Funnel cover

17. Sausage ller’s nozzle (ne)

18. Sausage ller’s nozzle (coarse)

19. Food pusher

INTRODUCTION

Thank you for purchasing our product.

In doing so, you have opted for an effective high-per-

formance appliance.

If the instructions on the correct use of this appliance

are not observed, the manufacturer shall assume no

responsibility for any resulting damage.

The operating instructions may refer to different mod-

els: any difference is clearly identied.

IMPORTANT SAFEGUARDS

1. When using the electrical

appliance, the below basic

safety precautions should be

followed:

2. Read all instructions.

3. Do not immerse the motor

unit of the blender in water, as

this would give rise to electric

shocks.

4. Before using it, check that

the voltage of the wall outlet

corresponds to the voltage

shown on the rating plate.

5. Do not operate any appliance

with a damaged cord / plug. If

the appliance malfunctions or

is dropped or damaged in any

manner return the appliance to

the nearest authorised service

facility for examination, repairs

or electrical / mechanical

adjustment.

6. Unplug it from the outlet when

not in use, before installing /

removing any parts and before

cleaning it.

7. Never introduce food by hand.

Always use the food pusher.

8. The metal blades and disc

are extremely sharp: handle

with care. Always hold the

blade attachments away from

the cutting edges, both when

handling and cleaning the unit.

9. The use of attachments not recommended by

the appliance manufacturer may cause injuries

or damage.

10. The appliance cannot be used to grind hard and/

or dry substances, otherwise the blade could be

blunted.

11. Do not let the cord hang over the edge of a table

/ counter or touch any hot surfaces.

12. Do not use ngers to scrape food away from

discharge outlet while appliance is operating.

Cut type injury may result.

13. During operating, never unplug the power outlet

to stop working directly. You must make sure the

ON/OFF button is on the off position rstly, then

unplug the power outlet.

14. Never run the appliance empty after assembling

the blade and blade tray. Otherwise the blade

and blade tray will be abraded seriously, and

accelerate the unit aging.

15. This appliance is not intended for use by

persons (including children) with reduced

physical, sensory or mental capabilities, or lack

of experience and knowledge, unless they have

been provided supervision or instructions on the

use of the appliance by a person responsible for

9

iten

operates normally; put the meat piece into

funnel, then press with the food pusher.

Attention: Always ensure bones and rind are

removed from the meat before mincing.

Note: The appliance is equipped

with a delayed start system: after

pushing the ON/OFF button, the

appliance will start operating with a

delay of about 2-3 seconds.

Note: The max operation time per time shall

not exceed 14 minutes when processing beef.

6. Place the funnel cover under the blade cover

to receive minced meat coming from the

appliance’s outlet.

7. Press the ON/OFF button

release it immediately when blocking exists

during grinding, then press the REVERSE

button, let the unit turn clockwise, then release

immediately, then press down the ON/OFF button

again; if the blocking still exists, repeat the operations

until the blocking disappears.

8. When nish grinding, press ON/OFF and unplug

to the power source.

9. Disassemble the mincer head assembly: press

lock button properly with one hand (see arrow

1 of Picture 4), turn the mincer head assembly

clockwise with the other hand and remove it (see

arrow 2 of picture 4).

Caution: Ensure that the motor unit is unplugged

when disassembling.

Making sausages

1. Assemble the mincer head, grinding screw,

sausage ller’s nozzle support, sausage ller’s

nozzle (select thick or thin according to your

preference) and blade cover as shown in the

picture 5.

Note: Never assemble blade and mincer die-

plates when making sausages, and do

not assemble sausages ller’s nozzle and

related support when grinding meat.

2. Fix the mincer head into the motor unit. Press

the lock button with one hand (see arrow 1 of

picture 2), and hold the mincer head with the

their safety.

16. Children should be supervised to ensure that

they do not play with the appliance.

17. Do not use outdoor.

18. This appliance is intended for domestic use only.

19. Save these instructions

OPERATING INSTRUCTIONS

Note: Before the rst use, please clean all the

detachable parts such as food pusher,

funnel, mincer head, die plate (large hole,

medium hole, small hole), blade cover,

blade, kibble cone, kibble shaper and so on

completely.

The blade is sharp, handle with care.

INSTRUCTION

Grinding

1. Assemble grinding screw, blade, blade tray and

blade cover as illustrated in picture (see picture

1) before grinding. Select proper mincer die-

plate (ne, medium or coarse holes) according

to your preference. Smaller holes will make

the minced meat thinner and more uniform.

Note: Align the location hole on the selected

die-plate to the pin; the rear

surface of the blade has a letter “B”, ensure

that the side of “B” is toward the grinding

screw when assembling (picture 1).

2. Fix the mincer head into the motor unit. Press the

lock button with one hand (see arrow 1 of picture

2), and hold the mincer head with the other hand,

insert it into the hole of the unit and turn it counter-

clockwise until it cannot move anymore (see

arrow 2 of picture 2). Release the lock button and

the mincer head is xed on the motor unit: tighten

the blade cover using the spanner to ensure all

elements are securely in place (see picture 3).

Caution: Make sure the appliance is

unplugged when assembling.

3. Put the funnel on the mincer head.

4. Ensure that the ON/OFF button is in release

state, then plug in power supply.

5. Press ON/OFF button: the grinding blade

turns counter-clockwise when the appliance

10

iten

other hand, insert it into the hole of the unit and

turn it counter-clockwise until it cannot move

anymore (see arrow 2 of picture 2). Release

the lock button and the mincer head is xed on

the motor unit: tighten the blade cover using the

spanner to ensure all elements are securely in

place.

3. Set clean small intestine to sausage pole as in

picture 6, then place minced meat into funnel.

4. Press the ON/OFF button, the appliance turns

anti-clockwise and the minced meat goes inside

the intestine; you can tie the intestine anywhere

you like with thread to make the sausage have

proper length.

CLEANING AND MAINTENANCE

1. Unplug the power cord before cleaning.

2. Disassemble all the parts from mincer head,

and immerse all of them in water for cleaning,

including the mincer head itself.

Caution: The blade is sharp, so handle carefully

when cleaning.

Note: The grinding screw can be disassembled

for cleaning if necessary, as shown in picture 7.

3. Wipe the outside surface of the motor unit with a

damp cloth, then drying thoroughly.

Note: Never immerse the motor unit in the

water for cleaning.

4. After cleaning all the accessories, dry them

completely, then assemble them in the food

pusher as shown in picture 8 (picture 8)

CLEANING TIP:

To remove the meat that is stuck in ne and medium

mincer die-plates, align the holes of the die-plates

with the blades-cleaning disc and push the blades-

cleaning disc into die-plate, as shown in picture 9.

Any meat stuck in the die-plate will be pushed out. Any

remaining meat that is still in the blade tray should be

washed off using a soft sponge and hot soapy water.

To remove foods from the die-plate (large hole), rinse

it under cold, running water to force meat from holes,

any remaining meat stuck on the blade tray should be

washed off using a soft sponge and hot soapy water.

Ensure that all attachments and discs are dried

thoroughly before storing. If trays are not dried, rust

may occur on the trays.

DISPOSAL OF OLD ELECTRICAL

APPLIANCES

The European Directive 2012/19/EU on Waste Elec-

trical and Electronic Equipment (WEEE), re-

quires that old household electrical applian-

ces must not be disposed of in the normal

unsorted municipal waste stream.

Old appliances must be collected separately

in order to optimise the recovery and recycling of the

materials they contain and reduce the impact on hu-

man health and the environment. The cros-

sed out “wheeled bin” symbol on the product

reminds you of your obligation, that when you

dispose of the appliance it must be separately col-

lected. Consumers should contact their local authority

or retailer for information concerning the correct di-

sposal of their old appliance.

Page is loading ...

Indesit Company SpA

Viale Aristide Merloni, 47

60044 Fabriano (AN), Italy

www.indesitcompany.com

ÜLKEYE ÖZGÜ BILGILER KITAPÇIĞIN SON SAYFASINDA BULABILIRSINIZ

MINCER

2014/10 - ver.1.3

Indesit MM 060 DSL0 Owner's manual

This manual is also suitable for

Indesit MM 060 DSL0 Owner's manual

in other languages

Related papers

Other documents