LG WD-14570RD Owner's manual

Brand: LG

Model: WD-14570RD

Category: Washing machines

Type: Owner's manual

P/No.: MFL31184275

WD-1257(0~9)RD

WD-1457(0~9)RD

WD-1657(0~9)RD

WD-1457ARD

WD-1457ERD

roduct Feature

ontents

Warnings ....................................................................................................................3

Specification ................................................................................................................5

Installation ...................................................................................................................6

Care before washing .................................................................................................11

Adding detergent .......................................................................................................12

Function ..................................................................................................................14

How to use washer ....................................................................................................15

Maintenance ..............................................................................................................25

Troubleshooting guide ...............................................................................................29

Terms of Warranty.....................................................................................................32



Direct Drive System

The advanced Brushless DC motor directly drives the drum without

belt and pulley.



Water Circulation

Spray detergent solution and water onto the load continuously.

Clothes are soaked more quickly and thoroughly during wash cycle.

The detergent suds can be removed more easily by the water shower during rinse

cycle. The water circulation system uses both water and detergent more efficiently.



Built-in Heater

Internal heater automatically heats the water to the best temperature on selected

cycles.



Child Lock

The Child lock prevents children from pressing any button to change the settings

during operation.



More economical by Intelligent Wash System

Intelligent Wash System detects the amount of load and water temperature, and

then determines the optimum water level and washing time to minimize energy and

water consumption.



Low noise speed control system

By sensing the amount of load and balance, it evenly distributes load to minimize

the spinning noise level.



Steam Washing and Refresh

Steam Washing features upgraded washing performance with low energy

consumption. Refresh cycle reduces wrinkles from dry clothes.



Automatic Wash Load Detection

Automatically detects the load and optimizes the washing time.



Safety device (Aqua lock)

Aqua lock System is designed for detecting water leak during operation to prevent

water from flooding over the floor.

󲷸 󲷸

arnings

For your safety, the information in this manual must be followed to minimize

the risk of fire or explosion, electric shock, or to prevent property damage,

personal injury, or loss of life.



READ ALL INSTRUCTIONS AND EXPLANATION OF THE INSTALLATION BEFORE USE

WARNING!

❊ Do not push down the door excessively, when washer door open.

This could topple over the washer.

• Before installation, check exterior damages. If it has,

do not install.

• Do not install or store the washer where it will

be exposed to the weather.

• Do not tamper with controls.

• Do not repair or replace any part of the washer

or attempt any servicing unless specifically

recommended in the user-maintenance instructions

or published user-repair instructions that you

understand and have the skills to carry out.

• Keep the area underneath and around your

appliances free of combustible materials such as

lint, paper, rags, chemicals, etc.

• Close supervision is necessary if this appliance is

used by or near children or infirm persons.

Do not allow them to play on, with, or inside this

or any other appliance.

• Keep washer away from fire.

• Do not leave the washer door open.

An open door could entice children to hang on the

door or crawl inside the washer.

• Never reach into washer while it is running.

Wait until the drum has completely stopped.

• The laundry process can reduce the flame retardant

of fabrics.

• To avoid such a result, carefully follow the garment

manufacturer’s wash and care instructions.

• Do not wash or dry articles that have been cleaned

in, washed in, soaked in, or spotted with

combustible or explosive substances (such as wax,

oil, paint, gasoline, degreasers, dry-cleaning

solvents, kerosene, etc.) which may ignite or

explode. Oil may remain in the tub after a whole

cycle resulting in fire during drying. So, do not load

oiled clothes.

• Do not slam the washer door closed or try to force

the door open when locked. This could result in

damage to the washer.

• When the machine runs at high temperature, the

front door may be very hot. Don’t touch it.

• To minimize the possibility of electric shock, unplug

this appliance from the power supply or disconnect

the washer at the household distribution panel by

removing the fuse or switching off the circuit breaker

before attempting any maintenance or cleaning.

• When unplugging power cord, do not pull out by

grasping the cord. Otherwise, the power cord may

be damaged.

• Never attempt to operate this appliance if it is

damaged, malfunctioning, partially disassembled, or

has missing or broken parts, including a damaged

cord or plug.

• Before discarding an old machine unplug it. Render

the plug useless. Cut off the cable directly behind

the appliance to prevent misuse.

• When a product was under water, Please call

service center. The risk of electric shock and fire.

GROUNDING INSTRUCTIONS

This appliance must be grounded. In the event of malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path

of least resistance for electric current. This appliance is equipped with a cord having an equipment-grounding conductor and grounding plug.

The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinance.

• Do not use an adapter or otherwise defeat the grounding plug.

• If you don’t have the proper outlet, consult an electrician.

IMPORTANT SAFETY INSTRUCTIONS

WARNING : To reduce the risk of fire, electric shock, or injury to persons when using

the washer, follow basic precautions, including the following:

SAVE THESE INSTRUCTIONS

WARNING :

Improper connection of the equipment-grounding conductor can result in risk of electric shock. Check with

a qualified electrician or serviceman if you are in doubt as to whether the appliance is properly grounded. Do not modify

the plug provided with the appliance - if it does not fit the outlet, have a proper outlet installed by a qualified electrician.

arnings

To minimize the risk of fire in a tumble dryer, the following should be observed:

• Items that have been spotted or soaked with vegetable or cooking oil constitute a fire

hazard and should not be placed in a tumble dryer.

Oil-affected items can ignite spontaneously, especially when exposed to heat

sources Such as in a tumble dryer. The items become warm, causing an oxidation

reaction in the oil. Oxidation creates heat. If the heat cannot escape, the items can

become hot enough to catch fire. Piling, stacking or storing oil-affected items can

prevent heat from escaping and so create a fire hazard.

If it is unavoidable that fabrics that contain vegetable or cooking oil or have been

contaminated by hair care products be placed in a tumble dryer they should first be

washed in hot water with extra detergent-this will reduce, but not eliminate, the

hazard. Washed in hot water with extra detergent-this will reduce, but not

eliminate, the hazard. The ‘cool down’ cycle of tumble dryers should be used to

reduce the temperature of the items. They should not be removed from the tumble

dryer or piled or stacked while hot.

• Items that have been previously cleaned in, washed in, soaked in or spotted with

petrol/gasoline, dry-cleaning solvents or other flammable or explosive substances

should not be placed in a tumble dryer.

Highly flammable substances commonly used in domestic environments include

acetone, denatured alcohol, petrol/gasoline, kerosene, spot removers (some

brands), turpentine, waxes and was removers.

• Items containing foam rubber (also known as latex foam) or similarly testured

rubber. like materials should not be dried in a tumble dryer on a heat setting.

Foam rubber materials can, when heated, produce fire by spontaneous combustion.

• Fabric softeners or similar products should not be used in a tumble dryer to eliminate

the effects of static electricity unless this practice is specifically recommended by the

manufacturer of the fabric softener or product.

• Undergarments that contain metal reinforcements should not be placed in a tumble

dryer.

Damage to the tumble dryer can result if metal reinforcements come loose during

drying. When available a drying rack could be used for such items.

• Plastic articles such as shower caps or babies waterproof napkin covers should not

be placed in a tumble dryer.

• Rubber-backed articles, clothes fitted with foam rubber pads, pillows, galoshes and

rubber-coated tennis shoes should not be placed in a tumble dryer.

pecification

Drawer

Inlet hose(1EA)

Option : Hot/Cold(2EA)

Spanner



Accessories

❋ The appearance and specifications may be varied without notice to raise the units quality.

 Name : Front loading washing machine

 Power supply : 220 - 240V~, 50Hz

 Size : 600mm(W)640mm(D)850mm(H)

 Weight : 66kg

 Wash Capacity/Max. Watt : Refer to the Rating Label

 Dry Capacity/Max. Watt : Refer to the Rating Label

 Max. Watt (Steam) : 1100W

 Spin speed : No Spin/400/800/1000/1200 [WD-1257(0~9)RD]

No Spin/400/800/1000/1400

[WD-1457(0~9)RD/WD-1457ARD/WD-1457ERD]

No Spin/400/800/1000/1600 [WD-1657(0~9)RD]

 Water consumption : 149

 Permissible water pressure : 0.3-10 kgf/cm

(30-1000 kPa)

nstallation

1. To prevent internal damage during

transport, the special 4 bolts are locked.

Before operating the washer, remove

the bolts along with the rubber bungs.

• If they are not removed, it may cause heavy

vibration, noise and malfunction.

3. Take out the 4 bolts along with the rubber

bungs by slightly twisting the bung. Keep

the 4 bolts and the spanner for the future

use.

• Whenever the appliance is transported, the

transit bolts must be refitted.

The appliance is fitted with transit bolts to prevent internal damage during transport.

• Packing and all transit bolts must be

removed before using the washer.

󳀙 When unpacking the base, be

sure to remove the additional

packing support in the middle of

the base packing.

2. Unscrew the 4 bolts with

the spanner supplied.

4. Close the holes with the caps supplied.



Transit bolts

Install or store where it will not be exposed to temperature below freezing or exposed to the

weather.

Properly ground washer to conform with all governing codes and ordinances.

The base opening must not be obstructed by carpeting when the washing machine is installed on a

carpeted floor.

In countries where there are areas which may be subject to infestation by cockroaches or other

vermin, pay particular attention to keeping the appliance and its surroundings in clean condition at

all times.

Any damage which may be caused by cockroaches or other vermin will not be covered by the

appliance guarantee.



Removing transit bolts

(Packing support may not

be used depending on

models.)

nstallation

Level floor :

Allowable slope under entire washer is 1˚

Power outlet :

Must be within 1.5 meters of either side of location of

washer. Do not overload the outlet with more than one

appliance.

Additional Clearance :

For wall, door and floor modeling is required.

(10cm : rear /2cm:right & left side)

Do not place or store laundry products on top of washer at

any times.

They can damage the finish or controls.



Installation place requirement



Positioning

Install the washer on a flat hard floor.

Make sure that air circulation around the washer is not impeded by carpets, rug etc.

• Never try to correct any unevenness in the floor with pieces of wood, cardboard or similar

materials under the washer.

• If it is impossible to avoid positioning the washer next to a gas cooker or coal burning stove,

an insulation(85x60cm) covered with aluminum foil on the side facing the cooker or stove,

must be inserted between the two appliance.

• The washer must not be installed in rooms where the temperature can drop below 0°C.

• Please ensure that when the washer is installed, it is easily accessible for the engineer in

the event of a breakdown.

• Adjust all four feet using the transit bolt spanner provided ensuring the appliance is stable,

and a clearance of approximately 20mm is left between the top of the washer and the

underside of the work-top.

nstallation

Water supply pressure must be between 30kPa and 1000kPa

(0.3~10kgf/cm

)

Don’t strip or crossthread when connecting Inlet hose to the valve.

If the water supply pressure is more than 1000kPa, a decompression

device should be installed.

• Two rubber seals are supplied with the water inlet hoses. They

are used for preventing water leaks.

• Make sure the connection to taps is tight enough.

• Periodically check the condition of the hose and replace the

hose if necessary.

• Make sure that there is no kink on the hose and that it is not

crushed.



When your washer has two valves.

• The Inlet hose which has red connector is for the hot water tap.

• If the washer has two valves, the energy is saved by using hot

valve.

■

Washing Machine is to be connected to the water mains using new hose-sets and old hose-sets should

not be used.

■

Connecting water supply hose

1. Do not use an extension cord or double adapter.

2. If the supply cord is damaged, it must be replaced by the manufacturer or its service agents or similarly

qualified person in order to avoid a hazard.

3. Always unplug the machine and turn off the water supply after use.

4. Connect the machine to an earthed socket in accordance with current wiring regulations.

5. The appliance must be positioned so that the plug is easily accessible.

• Repairs to the washing machine must only be carried out by qualified personnel. Repairs carried out by

inexperienced persons may cause injury or serious malfunctioning. Contact your local service center

• Do not install your washing machine in rooms where temperature below freezing may occur. Frozen hoses may burst

under pressure. The reliability of the electronic control unit may be impaired at temperatures below freezing point.

• If the appliance is delivered in the winter months and temperatures are below freezing : Place the washing

machine at room temperature for a few hours before putting it into operation.

■

Electrical connection

CAUTION concerning the Power Cord

Most appliances recommend they be placed upon a dedicated circuit; that is, a single outlet circuit

which powers only that appliance and has no additional outlets or branch circuits. Check the

specification page of this owner's manual to be certain.

Do not overload wall outlets. Overloaded wall outlets, loose or damaged wall outlets, extension cords,

frayed power cords, or damaged or cracked wire insulation are dangerous. Any of these conditions

could result in electric shock or fire. Periodically examine the cord of your appliance, and if its

appearance indicates damage or deterioration, unplug it, discontinue use of the appliance, and have

the cord replaced with an exact replacement part by an authorized servicer.

Protect the power cord from physical or mechanical abuse, such as being twisted, kinked, pinched,

closed in a door, or walked upon. Pay particular attention to plugs, wall outlets, and the point where

the cord exits the appliance.

CAUTION

NOTE

After completing connection, if water leaks from the hose, repeat the same steps. Use the most conventional type

of faucet for water supply. In case the faucet is square or too big, remove the spacing ring before inserting the

faucet into the adaptor.

nstallation



Installation of drain hose

• The drain hose should not be placed higher

than 100 cm above the floor. Water in the

washer does not drain or drains slowly.

• Proper securing of the drain hose will

protect the floor from damage due to water

leakage.

• When the drain hose is too long, do not

force back into the washer. This will cause

abnormal noise.

• When installing the drain hose sink,

secure it tightly with a string.

• Proper securing of the drain hose will

protect the floor from damage due to

water leakage.

This equipment is not designed for maritime use or for use mobile installations such as

caravans, aircraft etc.

Turn off the stopcock if the machine is to be left for any length of time (e.g. holiday),

especially if there is no floor drain(gully) in the immediate vicinity.

When disposing of the appliance, cut off the mains cable, and destroy the plug Disable the

door lock to prevent young children being trapped inside.

Packaging material (e.g. Films, Styrofoam) can be dangerous for children. There is a risk

of suffocation ! Keep all packaging well away from children

nstallation



Level adjustment



Concrete floors



Wooden floors (Suspended floors)

1. Adjusting the washing machine level properly prevents excessive

noise and vibration.

Install the appliance on a solid and level floor surface, preferably in a

corner of the room.

2. If the floor is uneven, adjust the adjustable feet as required.

(do not insert pieces of wood etc. under the feet)

Make sure that all four feet are stable and resting on the floor and

then check that the appliance is perfectly level. (use a spirit level)



After the washer is level, tighten the lock nuts up towards of the base of

the washer. All lock nuts must be tightened.

❊ Diagonal Check

When pushing down the edges of the washing machine top plate diagonally, the machine

should not move up and down at all. (Please, check both of two directions)

If machine rocks when pushing the machine top plate diagonally, adjust the feet again.

• The installation surface must be clean, dry and level.

• Install washer on a flat hard floor.



Tile floors (Slippery floors)

• Position each foot on the Tread Mate and level the machine to suit. (Cut Tread Mate into 70x70 mm

sections and stick the pieces on to the dry tile where machine is to be placed.)



Tread Mate is a self adhesive material used on ladders & steps that prevents slipping.

• Wooden floors are particularly susceptible to vibration.

• To prevent vibration we recommend you place rubber cups under each foot,

at least 15mm thick under the washer, secured to at least 2 floor beams with screws.

• If possible install the washer in one of the corners of the room, where the floor is more stable.



Insert the rubber cups to reduce vibration.



You can obtain the rubber cups (p/no.4620ER4002B) from the LG svc dept.

Important!

• Proper placement and levelling of the washer ensure long, regular and reliable operation.

• The washer must be absolutely horizontal and stand firmly in position.

• It must not “Seesaw” across corners under load.

• The installation surface must be clean, free from floor wax and other lubricant coatings.

• Do not let the feet of the washer get wet. If feet of the washer get wet, slipping may occur.

Timber or suspended type flooring may contribute to

excessive vibration and unbalance errors.

In the case that the washing machine is installed on a raised

platform, it must be securely fastened in order

to eliminate the risk that it might fall off.

NOTE

are before washing

1. Care Labels

Look for a care label on your clothes. This will tell you about the fabric content of your garment and

how it should be washed.

2. Sorting

To get the best results, Sort clothes into loads that can be washed with the same wash cycle.

Water temperature and spin speed and different fabrics need to be washed in different ways.

Always sort dark colors from pale colors and whites. Wash separately as dye and lint transfer can

occur causing discoloration of white etc. If possible, do not wash heavily soiled items with lightly

soiled one.

Soil (Heavy, Normal, Light) Separate clothes according to amount of soil.

Color (White, Lights, Darks) Separate white fabrics from colored fabrics.

Lint (Lint producers, Collectors) Wash lint producers and lint collectors

separately.

3. Caring before loading



Caring before washing



Before the first washing



Combine large and small items in a load. Load large items first. Large items should not be more than half

the total wash load.

Do not wash single items. This may cause an out-of-balance load. Add one or two similar items.

• Check all pockets to make sure that they

are empty. Items such as nails, hair clip,

matches, pens, coins and keys can damage

both your washer and your clothes.

• Close zippers, hooks and strings to

make sure that these items don’t

snag on other clothes.

• Pre treat dirt and stains by brushing a little

detergent dissolved in water onto stains like

collars and cuffs to help shift dirt.

• Check the folds of the flexible gasket (gray) and

remove any small articles,if any.

• Check inside of the drum and remove any left

items in it for next wash cycle.

• Remove any clothing or items on the flexible

gasket to prevent clothing and the gasket

damages.

Select a cycle (COTTON 60°C, add a half load of detergent) allow the unit to wash

without clothing. This will remove residues and water from the drum that may have been left

during manufacturing.

dding detergent

• Main wash only

➔

• Pre Wash + Main Wash

➔

• Do not exceed the maximum fill line.

Close the dispenser drawer slowly.

Overfilling can cause early dispensing

of the fabric softener which could stain

clothes.

• Do not leave the fabric softener in the

detergent drawer for more than 2 days.

(Fabric softener could harden)

• Softener will automatically be added

during the last rinse cycle.

• Do not open the drawer when water is

supplied.

• Solvents(benzene, etc) are not

allowable.

1. The Dispenser Drawer

2. Adding Fabric Softener



Adding detergent and fabric softener

Do not pour fabric softener

directly on the cloths

NOTE

dding detergent

• The detergent should be used according to the

instruction of the detergent manufacture.

• If too much detergent is used, too many suds

can occur and this will decrease the washing

result or cause heavy load to the motor.

• Use powder detergent only for the front

loading washer.

❇

If suds occur too much, pleas reduce the

detergent amount.

• Detergent usage may need to be adjusted

for water temperature, water hardness,

size and soil level of the load. For best

results, avoid oversudsing.

4. Water softener

• A water softener, such as Anti limescale

(Clagon) can be used to cut down on the

use of detergent in extremely hard water

areas. Dispense according to the amount

specified on the packaging.

First add detergent and then the water

softener.

• Use the quantity of detergent as for soft

water.

❋

Tips

Full load : according to

manufacturer’s recommendation.

Part load : 3/4 of the normal

amount.

Minimum load : 1/2 of full load.

• Detergent is flushed from the dispenser

at the beginning of the cycle.

1) Open the door and Tablets into the

drum.

3. Detergent dosage

5. Using the Tablets

MAXMAX

MAX

2) Load the laundry into the drum.

3) Close the door.

MAX

unction



Recommended courses according to the laundry type

Water

Program

Fabric Type Temp.

(Option)

Cotton

Synthetic

Allergy

Care

Delicate

Duvet

Quick 30

Rinse+

Spin

Refresh

Hand

Wash

/Wool

Color fast garments

(shirts, night dresses,

pajamas...)and lightly soiled

white cotton(underwear)

Polyamide, Acrylic,

Polyester

Allergy care is made for

cotton clothes because

of high temperature.

Delicate laundry easily

damaged

“Hand wash” marked

delicate and wool laundry

Cotton bedding with filling

duvet, pillow, blanket, sofa

cover with light filling

Colored laundry which is

lightly soiled fast

Cotton mixed, Polyeter

mixed Dress shirts, blouses

- Time Delay

- Steam Wash

- Intensive

- Pre Wash

- Rinse

- Medic Rinse

- Low Temp.

- Iron Dry

- Cupboard

Dry

- Very Dry

- Time

- Low Temp.

- Iron Dry

- Cupboard

Dry

- Very Dry

- Time

- Time Delay

- Intensive

- Rinse

- Medic Rinse

- Time Delay

- Steam

Default

❋ Water Temperature : Select the water temperature to the wash cycles. Always follow garment manufacture’s

care label or instructions when laundering.

❋ Intensive : When washing full load or heavily soiled laundry, you can increase effectiveness by choosing intensive option.

❋ Program setting with “Cotton 60°C + Steam Wash + Intensive” option for test in accordance or in conformity

with EN60456 and IEC60456.

❋ Pre Wash : If the laundry is heavily soiled, “Pre Wash” Cotton is recommended. Pre Wash is available in

Cotton, Synthetic and Allergy Care program.

❋ Medic Rinse : For high effectiveness or more purity in rinse operation you can choose Medic Rinse option.

Medic Rinse is default in Allergy Care program.

❋ Rinse

: Used to additional rinse, which may assist in removing traces of detergent residue.

By selecting Rinse+ function, the Rinse Time and the Rinse water are increased.

❋ Allergy Care : This program helps to reduce allergic reactions caused by house dust mite, and it does it by

killing and removing the mite in the laundry with the help of high temperature steam and

powerful rinse.

60°C

(Cold, 30°C,

40°C, 95°C)

40°C (Cold,

30°C, 60°C)

40°C

(Cold, 30°C)

30°C

(Cold, 40°C)

No Choose

95°C

(40°C, 60°C)

Rating

Less than

4kg

Less than

4kg

Less than

2kg

Less than

2kg

Less than

2kg

Maximum

Load

Option

Dry

(Option)

1 king size

(9 Tog)

Rating

3 items

ow to use washer

• Press the Power button to start.

• Press the Start/Pause button.

• Initial condition

- Wash : Main wash

- Rinse : 3 times

- Spin :

• 1600 rpm

[WD-1657(0~9)RD]

• 1400 rpm

[WD-1457(0~9)RD/1457ARD/1457ERD]

• 1200 rpm

[WD-1257(0~9)RD]

- Water temperature : 60˚C

- Program : Cotton

• Press the Power button to start.

• Select the conditions which you want to

use, by pressing each button.

For selecting the each conditions, please

refer to the page16~page24

• Press the Start/Pause button.

1. Cotton automatically

selected upon power on.

2. Manual Selecting

Allergy Care

ow to use washer

Program

• 9 programs are available according to the

laundry type.

• Lamp will light up to indicate selected program.

• When Start/Pause button is pressed, the Cotton

program is automatically selected.

- By turning the Program dial, the program is

selected in order of “ Cotton – Synthetic –

Delicate – Hand Wash/Wool – Duvet – Quick 30

– Rinse+Spin – Refresh – Allergy Care”.

Regarding to the laundry type for each program

Please refer to the page14.

1. Power

2. Initial Program

Power

• Press the Power button to turn power on and

off.

• To cancel the Time Delay function, the

Power button should be pressed.

• When the Power button is pressed, the

washer is ready for Cotton program. And the

other initial conditions as follows.

• So, if you want to advance into the washing

cycle without changing the program, just

press Start/Pause button and then the

washer will proceed.

■

Initial program

• [WD-1657(0~9)RD]

- Cotton Program / Main Wash /

Normal Rinse / 1600 rpm / 60˚C

• [WD-1457(0~9)RD/1457ARD/1457ERD]

- Cotton Program / Main Wash /

Normal Rinse / 1400 rpm / 60˚C

• [WD-1257(0~9)RD]

- Cotton Program / Main Wash /

Normal Rinse / 1200 rpm / 60˚C

Allergy Care

(1) (2) (3) (6) (7) (8) (9) (10) (11)(4) (5)

Allergy Care

(1) Button : Power

(2) Dial : Program

(3) Button : Start/Pause

(4) Button : Time Delay

(5) Button : Steam Wash

(6) Button : Temperature

(7) Button : Spin

(8) Button : Option

(9) Button : Child Lock

(10) Button : Tub Clean

(11) Dial : Dry

ow to use washer

Start/Pause

• This Start/Pause button is used to start

wash cycle or pause the wash cycle.

• If temporary stop of wash cycle is needed,

press “Start/Pause” button.

• When in Pause, the power is turned off

automatically after 4 minutes.

• NB. The door will not open before 1 to 2

minutes when Pause is selected,

or at the end of the wash cycle.

1. Start

2. Pause

• While the "Detecting" is shown in the display

the machine rotates slowly and detects how

many laundries are loaded in the drum. It

will take a few seconds.

• Available in Cotton, Synthetic and Allergy

Care program.

3. Detecting

4. Door Lock

Allergy Care

Time Delay

Preparing washing before starting “Time Delay”

- Turn on the water tap.

- Load laundry and close the door.

- Place the detergent and fabric softener in

the drawer.

• How to set “Time Delay”

- Press Power button.

- Turn the Program dial to select

the program you require.

- Press Time Delay button and set the

desired time.

- Press the Start/Pause button.

• If Time Delay button is pressed, “3:00” is

displayed. The maximum delayed time is

19:00 hours and the minimum time is 3:00

hours.

• Each pressing of the button advances time

delay by one hour.

• To cancel the time delay, press the

Power button.

• Time Delay is ‘expected time’ from the

present to the completion of washing cycle

or selected process (Wash, Rinse, Spin).

According to the condition of water supply and

temperature, the delayed time and the actual

washing time may vary.

Allergy Care

• Lights whenever the door of the washer is

locked.

• The door can be unlocked by pressing the

Start/Pause button to stop the washer.

• The door can be opened after a short delay.

Allergy Care

ow to use washer

Steam Wash

By pressing the Steam Wash button, Steam

Function Can be selected.

When Steam Function is selected, Steam wash

( ) LED lights on.

Steam Wash is

• For normally soiled full load.

• For tough stained clothes, underway, or baby

Clothes.

• Steam Wash is available with Cotton, Synthetic,

Allergy Care program.

Refresh cycle is fixed Steam wash.

• This option features upgraded washing

performance with low energy.

• Do not load delicates such as wool, silk, and

easily discolored clothes.

NOTE:

- Steam wash is a highly concentrated and

efficient.

It may seem there is no water inside the

drum(normal condition).

- During the steam cycle the strong steam

spray may not be seen through the door

(normal condition).

- During the steam operation, a spraying sound

will be heard. (normal condition)

- Do not try to open the door while operating.

Steam can cause severe burns.

CAUTION:

- Do not reach into the washer while operating.

Steam can cause severe burns.

Refresh

■ Refresh cycle

• For slightly wrinkled clothes which have

been stored for an extended time.

It just makes wrinkled clothes easy to iron

(Do not load wet clothes).

• Wrinkles will be reduced.

■ How to use Refresh cycle

1. Turn on the washer and select the Refresh program.

2. Load 3 items or less and close the door.

3. Press the Steam Wash button repeatedly until the

desired and correct number of items is displayed.

Initial display is 2 items.

4. Press the Start/Pause button.

CAUTION:

- Do not reach into the washer while operating.

Steam can cause severe burns.

- Keep pets away from the washer.

[Precautionary Notes]

- The Refresh cycle is not like other washing or

drying cycles.

- Due to the characteristic of cotton fibers, this cycle

is not recommended for 100% cotton clothing.

- Remove stains from clothing before using the

Refresh cycle to prevent permanently setting the

stains by high heat.

- Be sure that the faucet is open. This cycle uses a

little water to produce steam.

- Be careful not to touch the door. It can be very hot.

- Do not open the door while operating.

Steam can cause severe burns.

- After removing clothes from the Refresh cycle they

may feel slightly damp wait at least 10 minutes

before putting the clothes on.

- Best result are achieved when articles are of similar

size and fabric type. Do not overload

(Load less than 3 dress shirtes)

Allergy Care

Program

Cotton

Synthetic

Allergy Care

Temperature

60°c (30°c, 40°c, 95°c)

40°c (30°c, 60°c)

95°c (40°c, 60°c)

Press the Steam Wash button.

ow to use washer

Water Temp.

• By pressing the Temp.

button, the water

temperature can be

selected.

- Cold

- 30˚C / 40˚C / 60˚C / 95˚C

• Water temperature can be selected as below

according to the program.

- Allergy Care

40˚C – 60˚C – 95°C

- Cotton

Cold – 30˚C – 40˚C – 60˚C – 95˚C

- Synthetic

Cold – 30˚C – 40˚C – 60˚C

- Delicate & Quick 30 & Hand Wash/Wool &

Duvet

Cold – 30˚C – 40˚C

The required temperature lamp will light up for

identification.

For the more detailed information, please refer to

the page14.

Allergy Care

Option

By pressing each

the button, each

function will be

selected.

2. Pre Wash

• Use this option for load that need pretreatment.

Add 16 minutes pre wash and drain.

- When using Pre Wash option, do not use

liquid detergent in the main wash

comportment. Use powder for the main wash.

• Available in Cotton, Synthetic and Allergy Care

program.

4. Medic Rinse

• For high effectiveness or more purity in rinse

operation you can choose Medic Rinse option.

• Available in Cotton, Synthetic and Allergy Care

program.

• Medic Rinse is default in Allergy Care program.

The required temperature lamp will light up for

identification.

1. Intensive

• When washing full load or heavily soiled

laundry, you can increase effectiveness by

choosing intensive option.

• By selecting the Intensive option, the wash

time may be extended, depending on the

program selected.

• To use this option, press the intensive button

once before the wash program is started.

Allergy Care

3. Rinse

• Used to additional rinse, which may assist in

removing traces of detergent residue.

• By selecting Rinse

function, the Rinse

Time and the Rinse water are increased.

Page is loading ...

LG WD-14570RD Owner's manual

Brand: LG

Model: WD-14570RD

Category: Washing machines

Type: Owner's manual

Download PDF

report

LG WD-14570RD Owner's manual

LG WD-14570RD Owner's manual

Related papers

Other documents