FLEETFLIX AI Pro Dash Camera User guide
- Category
- Car video systems
- Type
- User guide
FLEETFLIX AI Pro Dash Camera is a powerful device packed with the latest advancements in technology, offering fleets of all sizes a way to enhance driver and fleet safety, and reduce safety-related costs. The camera is fully integrated into the Geotab Platform and offers a wide range of features, including:
- Driver and fleet safety: The camera uses artificial intelligence (AI) to detect and alert drivers to potential hazards, such as lane departures, forward collisions, and speeding. It also provides real-time coaching to help drivers improve their driving habits.
- Reduced safety-related costs: The camera can help fleets reduce safety-related costs by identifying and addressing risky driving behaviors. It can also provide data to support insurance claims and reduce litigation costs.
FLEETFLIX AI Pro Dash Camera is a powerful device packed with the latest advancements in technology, offering fleets of all sizes a way to enhance driver and fleet safety, and reduce safety-related costs. The camera is fully integrated into the Geotab Platform and offers a wide range of features, including:
- Driver and fleet safety: The camera uses artificial intelligence (AI) to detect and alert drivers to potential hazards, such as lane departures, forward collisions, and speeding. It also provides real-time coaching to help drivers improve their driving habits.
- Reduced safety-related costs: The camera can help fleets reduce safety-related costs by identifying and addressing risky driving behaviors. It can also provide data to support insurance claims and reduce litigation costs.
5
G
Installing the Cables
G
■
■
■
■
.
ACC Connector
a FLEETFLIX
FLEETFLIX
WHAT ARE THE
BENEFITS OF
THE FLEETFLIX
TECHNOLOGY?
After installing the camera, the following measurements are needed
•Hood length - the distance from the front lens of the camera and the front
bumper
•Vehicle width - the total width of the vehicle at its widest point in front of the
camera (typically wheel arch to wheel arch)
•Camera height - the distance from the ground to the bottom of the camera
Driver position - which side of the vehicle the steering wheel is on, (left hand
is typical for American market vehicles)
After install has been completed and measurements have been saved in the
database, the camera will need to be calibrated. To calibrate the camera properly
you will need to take the vehicle on a short drive under these conditions:
•Good contrast for lane markers
•Capable of supporting 30+ mph for 3-5 minutes
•Avoids hills or turns
•Reasonable weather
•Light traffic
While the vehicle is driving down the road in these optimal conditions, press and
hold down the driver alert button for 4 seconds. The camera will announce
"Calibration Started" and once complete camera will announce "Calibration
Done". Once calibration is complete, your camera has been successfully set up
and returning the button to driver alert. If the camera is ever removed or
unmounted, calibration will need to be completed again.
To start Calibration
S5
- If using LDW, gray and pink input wires will need to be connected.
S6
- Remove the right panel I/O cover.
S7
- Feed the 12-pin connector of the OBD II Power Cable through the
hole on the right panel I/O cover.
S8
- Reinstall the right panel I/O cover. Make sure to tighten the screw.
S9
- Connect the other end of the OBD II Power Cable to the Blade Fuse
Holder cable.
S10
- Plug in the OBD II Power Cable to the OBD II connector in the
vehicle.
Mounting
Sl
- Attach the adhesive tape mounting bracket or optional suction cup
onto the Fleetflix Dash Cam.
S2
- Find a suitable place to install the FleetFlix Dash Cam onto the wind
shield. Use alcohol to clean the glass before mounting the device. (It is
recommended to install the device in the center of the wind shield
below the review mirror.)
Installing the Micro SD Card (As Needed)
Sl
- Loosen the screw of the right panel I/O cover, remove cover.
S2
- Locate the Micro SIM Card slot.
S3
- Insert a Micro SIM card into card slot. Use your fingernail to press the
card into the slot. When fully inserted, the card will snap into the slot.
Sl - Reference the vehicle's user manual to find the location of the fuse box and
OBD connector. Then check the ACC fuse specification on the box cover.
S2 - Pull out the ACC fuse.
S3 - Select the appropriate Blade Fuse Holder cable. Plug in the ACC fuse that was
removed from the fuse box into the Blade Fuse Holder cable, and then plug in the
other ACC fuse that we provided.
S4 - Plug in the Blade Fuse Holder cable into the ACC fuse slot in the fuse box.
-
1
-
2
-
3
FLEETFLIX AI Pro Dash Camera User guide
- Category
- Car video systems
- Type
- User guide
FLEETFLIX AI Pro Dash Camera is a powerful device packed with the latest advancements in technology, offering fleets of all sizes a way to enhance driver and fleet safety, and reduce safety-related costs. The camera is fully integrated into the Geotab Platform and offers a wide range of features, including:
- Driver and fleet safety: The camera uses artificial intelligence (AI) to detect and alert drivers to potential hazards, such as lane departures, forward collisions, and speeding. It also provides real-time coaching to help drivers improve their driving habits.
- Reduced safety-related costs: The camera can help fleets reduce safety-related costs by identifying and addressing risky driving behaviors. It can also provide data to support insurance claims and reduce litigation costs.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Other documents
-
VIA Technologies Mobile360 D700 User manual
-
Vacron vvh-mde31 User manual
-
Vacron VVG-MDE31A User manual
-
FRC inView 360 Fusion Installation guide
-
-
-
Thinkware F800 User manual
-
Volvo 2014 Owner's manual
-
Volvo 2014 Owner's manual
-
Volvo S80 2012 Owner's manual